共查询到20条相似文献，搜索用时 171 毫秒
1.
高科技厂房精密仪器工作平台的微振混合控制 总被引：2，自引：1，他引：1
车辆运行过程中引起的竖向地面微幅振动是影响高科技厂房精密仪器正常运行的重要因素。本文采用隔振与主动控制相结合的混合控制系统,以高科技厂房及精密仪器工作平台的有限元动力方程为基础,采用子优化控制方法建立了高科技厂房及精密仪器工作平台的分析模型,探讨了车辆运行所引起的高科技厂房精密仪器工作平台竖向微幅振动的混合控制分析方法。一座典型的三层高科技厂房的算例分析表明,采用混合控制方法能够有效地减小高科技厂房精密仪器工作平台的竖向微幅振动。 相似文献
2.
This paper presents an experimental study, while a companion paper addresses an analytical study, to explore the possibility of using a hybrid platform to mitigate vibration of a batch of high‐tech equipment installed in a building subject to nearby traffic‐induced ground motion. A three‐storey building model and a hybrid platform model are designed and manufactured. The hybrid platform is mounted on the building floor through passive mounts composed of leaf springs and oil dampers and controlled actively by an electromagnetic actuator with velocity feedback control strategy. The passive mounts are designed in such a way that the stiffness and damping ratio of the platform can be changed. A series of shaking table tests are then performed on the building model without the platform, with the passive platform of different parameters, and with the hybrid platform. The experimental results demonstrate that the hybrid platform is very effective in reducing the velocity response of a batch of high‐tech equipment in the building subject to nearby traffic‐induced ground motion if dynamic properties of the platform and control feedback gain are selected appropriately. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
3.
The experimental results of using a hybrid platform to mitigate vibration of a batch of high‐tech equipment installed in a building subject to nearby traffic‐induced ground motion have been presented and discussed in the companion paper. Based on the identified dynamic properties of both the building and the platform, this paper first establishes an analytical model for hybrid control of the building‐platform system subject to ground motion in terms of the absolute co‐ordinate to facilitate the absolute velocity feedback control strategy used in the experiment. The traffic‐induced ground motion used in the experiment is then employed as input to the analytical model to compute the dynamic response of the building‐platform system. The computed results are compared with the measured results, and the comparison is found to be satisfactory. Based on the verified analytical model, coupling effects between the building and platform are then investigated. A parametric study is finally conducted to further assess the performance of both passive and hybrid platforms at microvibration level. The analytical study shows that the dynamic interaction between the building and platform should be taken into consideration. The hybrid control is effective in reducing both velocity response and drift of the platform/high‐tech equipment at microvibration level with reasonable control force. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
4.
High‐tech equipments engaged in the production of ultra‐precision products have very stringent vibration criteria for their functionality in normal operation conditions and their safety during an earthquake. Most previous investigations were based on simplified planar models of building structures, despite the fact that real ground motions and structures are always three‐dimensional. This paper hence presents a three‐dimensional analytical study of a hybrid platform on which high‐tech equipments are mounted for their vibration mitigation. The design methodology of the hybrid platform proposed in this study is based on dual‐level performance objectives for high‐tech equipments: safety against seismic hazard and functionality against traffic‐induced microvibration. The passive devices (represented by springs and viscous dampers) and the active actuators are designed, respectively, to meet vibration criteria corresponding to safety level and functionality level. A prototype three‐story building with high‐tech equipments installed on the second floor is selected in the case study to evaluate the effectiveness of the hybrid platform. The optimal location of the platform on the second building floor is determined during the design procedure in terms of the minimal H 2 cost function of absolute velocity response. The simulation of the coupled actuator‐platform‐building system subjected to three‐dimensional ground motions indicates that the optimally designed hybrid platform can well achieve the dual target performance and effectively mitigate vibration at both ground motion levels. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
5.
To ensure the high quality of ultra‐precision products such as semiconductors and optical microscopes, high‐tech equipment used to make these products requires a normal working environment with extremely limited vibration. Some of high‐tech industry centres are also located in seismic zones: the safety of high‐tech equipment during an earthquake event becomes a critical issue. It is thus imperative to find an effective way to ensure the functionality of high‐tech equipment against microvibration and to protect high‐tech equipment from damage when earthquake events occur. This paper explores the possibility of using a hybrid platform to mitigate two types of vibration. The hybrid platform, on which high‐tech equipment is installed, is designed to work as a passive isolation platform to abate mainly acceleration response of high‐tech equipment during an earthquake and to function as an actively controlled platform to reduce mainly velocity response of high‐tech equipment under normal working condition. To examine the performance of the hybrid platform, the analytical model of a coupled hybrid platform and building system incorporating with magnetostrictive actuators is established. The simulation results obtained by applying the analytical model to a high‐tech facility indicate that the proposed hybrid platform is feasible and effective. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
6.
While many cases of structural damage in past earthquakes have been attributed to strong vertical ground shaking, our understanding of vertical seismic load effects and their influence on collapse mechanisms of buildings is limited. This study quantifies ground motion parameters that are capable of predicting trends in building collapse because of vertical shaking, identifies the types of buildings that are most likely affected by strong vertical ground motions, and investigates the relationship between element level responses and structural collapse under multi‐directional shaking. To do so, two sets of incremental dynamic analyses (IDA) are run on five nonlinear building models of varying height, geometry, and design era. The first IDA is run using the horizontal component alone; the second IDA applies the vertical and horizontal motions simultaneously. When ground motion parameters are considered independently, acceleration‐based measures of the vertical shaking best predict trends in building collapse associated with vertical shaking. When multiple parameters are considered, Housner intensity (SI), computed as a ratio between vertical and horizontal components of a record (SIV/SIH), predicts the significance of vertical shaking for collapse. The building with extensive structural cantilevered members is the most influenced by vertical ground shaking, but all frame structures (with either flexural and shear critical columns) are impacted. In addition, the load effect from vertical ground motions is found to be significantly larger than the nominal value used in US building design. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
7.
This paper presents an experimental study to explore the possibility of using a hybrid platform to ensure the functionality of high‐tech equipment against microvibration and to protect high‐tech equipment from damage when an earthquake occurs. A three‐storey building model and a hybrid platform model were designed and manufactured. The two‐layer hybrid platform, on which the high‐tech equipment is placed, was installed on the first floor of the building to work as a passive platform aiming at abating acceleration response of the equipment during an earthquake and functioning as an actively controlled platform that intends to reduce velocity response of the equipment under a normal working condition. For the hybrid platform working as a passive platform, it was designed in such a way that its stiffness and damping ratio could be changed, whereas for the hybrid platform functioning as an active platform, a piezoelectric actuator with a sub‐optimal velocity feedback control algorithm was used. A series of shaking table tests, traffic‐induced vibration tests and impact tests were performed on the building with and without the platform to examine the performance of the hybrid platform. The experimental results demonstrate that the hybrid platform is feasible and effective for high‐tech equipment protection against earthquake and microvibration. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
8.
以北京地铁6号线新华大街站公共区Y型柱地铁车站为工程背景,利用FLAC3D有限差分程序数值模拟分析,研究超浅埋大跨度、高断面、Y形柱地铁车站结构分别在仅输入水平向地震动和同时输入水平向与竖向地震动情况下的地震响应特性。结果表明:(1)与仅输入单向地震动相比,双向地震动耦合作用下车站各测点的峰值加速度和应力值均增大,而相对水平位移减小,且随着输入地震动强度的增加,竖向地震动影响率呈递减趋势;(2)双向地震动作用下,同一工况Y形柱叉支处各测点的竖向位移明显增大,且各测点的竖向位移值较为均匀,而单向水平地震动作用下各测点竖向位移差异较大;(3)与单向水平地震动相比,竖向地震动的输入对各测点间的水平方向地震动特性规律影响较小。 相似文献
9.
Linear and non-linear responses of a two-story structural model excited by near-source fault-normal pulse and fault-parallel displacement are investigated. For the considered linear system, the multi-component differential-motion effects amplify the first-story drifts 3.0–4.0 times relative to the excitation by synchronous horizontal ground motion only. The contribution of horizontal differential ground motion to the total drift is about two thirds, and the contribution of vertical and rocking differential ground motions is about one third. For the considered nonlinear system, the effects of vertical and rocking differential ground motions become more significant for the second-story drifts. The horizontal differential ground motion amplifies the first-story drifts, but the simultaneous action of horizontal, vertical, and rocking differential ground motions can amplify the first- and second-story drifts by more than 2.0 times relative to the drifts computed for uniform horizontal ground motion only. 相似文献
10.
Many studies have focused on horizontal ground motion, resulting in many coherency functions for horizontal ground motion while neglecting related problems arising from vertical ground motion. However, seismic events have demonstrated that the vertical components of ground motion sometimes govern the ultimate failure of structures. In this paper, a vertical coherency function model of spatial ground motion is proposed based on the Hao model and SMART 1 array records, and the validity of the model is demonstrated. The vertical coherency function model of spatial ground motion is also compared with the horizontal coherency function model, indicating that neither model exhibits isotropic characteristics. The value of the vertical coherency function has little correlation with that of the horizontal coherency function. However, the coherence of the vertical ground motion between a pair of stations decreases with their projection distance and the frequency of the ground motion. When the projection distance in the wave direction is greater than 800 meters, the coherency between the two points can be neglected. 相似文献
11.
Site response to earthquake loading is one of the fundamental problems in geotechnical earthquake engineering. Most site response analyses assume vertically propagating shear waves in a horizontally layered soil–rock system and simply ignore the effect of site response to vertical earthquake motion, although actual ground motions are comprised of both horizontal and vertical components. In several recent earthquakes very strong vertical ground motions have been recorded, raising great concern over the potential effect of vertical motion on engineering structures. Being a step toward addressing this concern, this paper presents a simple and practical procedure for analysis of site response to both horizontal and vertical earthquake motions. The procedure involves the use of the dynamic stiffness matrix method and equivalent-linear approach, and is built in the modern MATLAB environment to take full advantages of the matrix operations in MATLAB. The input motions can be specified at the soil–bedrock interface or at a rock outcropping. A detailed assessment of the procedure is given, which shows that the procedure is able to produce acceptable predictions of both vertical and horizontal site responses. 相似文献
12.
利用关东盆地及其周边KiK-net台网井上台站记录的2004—2017年15次中强地震（矩震级为5.1～6.9级）构建三分量记录显著持时Ds5-95数据库。针对该数据库,基于残差分析方法和3种水平向地震动持时参数预测方程,计算并给出事件间残差和事件内残差及其随不同类别参数的变化。在此基础上,初步探讨了水平向地震动持时预测方程应用于预测竖向地震动持时的可行性及盆地对三分量地震动持时的影响。研究结果表明,对于震源距和场地VS30相当的情况,盆地内台站持时普遍大于盆地外台站持时,盆地内、外台站竖向地震动持时均大于水平向地震动持时;3种预测方程均可实现对盆地外台站水平向地震动Ds5-95的合理估计,但在一定程度上低估了盆地内台站的水平向地震动Ds5-95;3种预测方程均无法直接应用于竖向地震动持时预测。 相似文献
13.
We present the results of an experiment about the effects on the seismic ground motion of a hill of large dimensions (6km long, 3km large and 700m high) near Corinth (Greece). We installed 7 seismometers across the hill, and analyzed the ground motion with different methods: the classical spectral ratios (CSR) and the horizontal to vertical spectral ratios calculated both on noise (HVNR) and earthquake data (RF). The amplification at the resonant frequency (around 0.7Hz) is low, as expected, but one of the two stations installed at the top exhibits large amplification (up to a factor of 10) at 3Hz. The comparison between the H/V results and the CSR ones suggests that the former method is able to point out the fundamental frequencies of a hill. Amplifications and spatial localization predicted by numerical 3D modeling are consistent with the experimental data only at frequencies lower than 1Hz. 相似文献
14.
显著的竖向地震动是近断层地震动区别于远场地震动的重要特征之一,为更合理地确定竖向地震动作用,研究了近断层区域竖向地震动的反应谱特征及其与水平向反应谱比值的影响因素.首先,选取1952—1999年世界范围内震级在M5.4—7.6之间的18次地震的地震动记录,研究竖向地震加速度反应谱及其与水平向加速度反应谱比值特征;然后统计分析了断层距、场地条件、震级以及断层机制对竖向与水平向加速度反应谱比的影响.结果表明,一般情况下竖向加速度具有更丰富的短周期分量,并且竖向加速度反应谱衰减较慢;断层距在20km以内的近断层区域、软弱土层场地、中等震级地震和逆断层大震级中长周期范围等条件下,具有较大的竖向与水平向加速度反应谱比值;在近断层区域的结构抗震设计中应充分考虑竖向地震动的影响. 相似文献
15.
软土具有高灵敏度、低强度等特性,在地震过程中极易产生震陷。基于OpenSees数值模拟方法对软土场地的震陷反应进行非线性动力有限元分析,通过改变地震动峰值加速度、频谱特性、输入方式来研究其对软土震陷的影响。结果表明,地震动峰值加速度对地基土的不均匀震陷有显著影响,地震动峰值加速度越大,震陷量显著增大,震陷影响深度更大,对水平地表造成的破坏范围也更大;地震动频谱特性对软土震陷有重要影响,当地震动卓越频率与场地自振频率相近时,其幅值越大,产生的震陷越严重;水平、竖向同时输入地震动的方式能更好地反映土体的振动及震陷响应。该研究成果对探索软土震陷的机理有一定的指导意义。 相似文献
16.
In this paper, a field experiment was carried out to study train-induced environmental vibrations. During the field experiment, velocity responses were measured at different locations of a six-story masonry structure near the Beijing-Guangzhou Railway and along a small road adjacent to the building. The results show that the velocity response levels of the environmental ground and the building floors increase with train speed, and attenuate with the distance to the railway track. Heavier freight trains indu... 相似文献
17.
Sachi Furukawa Eiji Sato Yundong Shi Tracy Becker Masayoshi Nakashima 《地震工程与结构动力学》2013,42(13):1931-1949
Base isolation is a well known technology that has been proven to reduce structural response to horizontal ground accelerations. However, vertical response still remains a topic of concern for base‐isolated buildings, perhaps more so than in fixed‐base buildings as isolation is often used when high performance is required. To investigate the effects of vertical response on building contents and nonstructural components, a series of full‐scale shaking table tests were conducted at the E‐Defense facility in Japan. A four‐story base‐isolated reinforced concrete building was outfitted as a medical facility with a wide variety of contents, and the behavior of the contents was observed. The rubber base isolation system was found to significantly amplify vertical accelerations in some cases. However, the damage caused by the vertical ground motions was not detrimental when peak vertical floor accelerations remained below 2 g with three exceptions: (1) small items placed on shelves slid or toppled; (2) objects jumped when placed on nonrigid furniture, which tended to increase the response; and (3) equipment with vertical eccentricities rocked and jumped. In these tests, all equipment and nonstructural components remained functional after shaking. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
18.
磁流变阻尼器在受控结构中的优化布置 总被引：4，自引：0，他引：4
高层建筑结构中由于地震引起的结构体系的振动是十分严重的,利用磁流变阻尼器进行振动控制的方法可以有效减小体系的振动反应、这种振动控制的效果,不仅取决于阻尼器出力大小和控制算法的优化,也取决于阻尼器在高层结构中的布置位置。首先对近年来出现的许多优化布置方法进行了阐述,论述了这些方法的优缺点,然后选用了一种优化布置方法并结合一个结构体系进行了阻尼器的优化布置研究,最后给出了阻尼器优化布置的几个原则。研究的结果表明通过阻尼器在高层结构中的优化布置可以有效提高振动控制的效果． 相似文献
19.
三维隔震(振)支座的工程应用与现场测试 总被引：2，自引：0，他引：2
首先介绍了一种新型三维隔震(振)支座,该支座由联接件、竖向隔振支座和水平隔震支座组成。竖向隔振支座和水平隔震支座具有较小刚度,采用该类型支座的隔震结构,其竖向基频和水平基频可远离地铁、铁路振动和地震的主频,从而实现竖向隔振和水平隔震作用。其次介绍了该三维隔震(振)支座在某一地铁平台上部结构中的应用情况,对该类型支座进行了竖向性能和水平性能试验。最后对三维隔震(振)结构与传统结构进行了地铁运行时结构振动的对比测试。测试结果表明:三维隔震(振)系统对振动的高频信号具有显著衰减效果。 相似文献
20.
为了研究近断层地震动速度脉冲及强竖向地震动对风机塔地震响应的影响,以某陆上风电场1.5 MW风机塔为研究对象开展了结构在水平向脉冲型地震动、水平向非脉冲型地震动、水平与竖向地震动组合3种地震输入工况的时程分析。通过3种工况下塔顶位移时程、加速度时程、塔底剪力、弯矩及轴力的对比分析发现:近断层速度脉冲对结构塔顶水平位移、塔顶水平加速度、塔底剪力与弯矩均影响显著;竖向地震动会加大结构的塔顶竖向加速度响应及塔底轴力响应;随着竖向与水平加速度峰值比增大,塔顶竖向加速度响应增大,最大轴力随着峰值比增大而增大,最小轴力随着峰值比增大而减小。此外,增量动力分析表明,采用自接触的有限元模型可以更真实地预测风机塔的失稳破坏机制。 相似文献