共查询到20条相似文献，搜索用时 151 毫秒
1.
2.
活跃在中国南海的内孤立波已经成为该地区海洋油气资源开发中不得不考虑的因素。跨接管作为连接水下油气储存开采设施与海面油气处理设施的重要装置,由于具有较大柔性,由内孤立波引起的剪切海流将会对其产生巨大影响。采用KdV方程对内孤立波进行模拟,基于向量式有限元法,建立了柔性跨接管的动力学分析模型,对不同方向内孤立波作用下的跨接管的动力性能进行分析。分析结果表明在内孤立波作用下,跨接管存在一个明显的动力过程,能够导致跨接管产生较大的位置移动及其整体位置的抬升,同时跨接管对于内孤立波的入射角十分敏感,其内力可能发生突然变化。内孤立波的振幅对跨接管的极值响应有显著影响。 相似文献
3.
海洋平台结构系统可靠性分析 总被引：6，自引：0，他引：6
本文研究了对三维模型的导管架平台结构系统可靠性评估方法。在极值载荷条件下，分别以极限冲剪应力及屈曲临界应力作为管节点及杆件的极限强度，采用增量载荷法建立失效模式安全余量方程。同时研究了求取结构系统主要失效模式的自动算法及计算系统失效概率的方法。作为一个算例，运用作者开发的计算机程序，对一固定式导管架平台进行了可靠性分析，验证了本文方法对开展三维模型平台结构系统可靠性评估是可行的。 相似文献
4.
5.
基于深海平台系统的耦合时域分析技术和结构可靠性理论,分析深水系泊系统在灾害性极限海况下的失效模式。根据系泊链的结构形式特点,建立破断强度的概率模型;并根据系泊链动力响应时间历程,采用广义极值理论,通过对非线性随机动力响应的数值拟合,提出建立载荷概率模型的方法。并以某半潜平台系泊系统为研究对象,通过不同极限环境条件下的分析对比,研究载荷方向对可靠性指标的影响。根据分析结果可知,在200年一遇海况下,当环境载荷方向是135°时,系统可靠性指标,已低于目标可靠性指标要求,该系泊系统处于不安全状态。 相似文献
6.
海底管线是海洋石油的重要输运手段。为满足输送工艺的需要,正常工作条件下管线往往被施加较高的温度和压强,高温高压使管线内产生附加应力,当附加应力大于土体对管线的约束力时,管线就会发生整体屈曲。过度的水平向整体屈曲会导致截面产生较大的弯曲应力和压缩应变,对管线系统的安全运行造成威胁,因此需要对发生水平向整体屈曲后的管线进行验算。采用解析解法、规范法和有限元法对管线的整体屈曲进行分析,提出了应用临界屈曲荷载值域空间和值域下限来判断不同缺陷大小下管线是否发生水平向整体屈曲的方法。结合工程实例,分别采用内力控制标准和位移控制标准对管线水平向整体屈曲后是否失效进行了验算。研究指出,相较于位移标准,内力控制标准更为严格。 相似文献
7.
非黏结柔性管道骨架层由不锈钢材料互锁缠绕而成,主要用于抵抗外压防止软管发生压溃失效.骨架层失效是柔性软管故障的最大风险,骨架层失效模式主要分为压溃失效和拉伸失效.采用非线性有限元方法并且考虑几何大变形、材料非线性、接触和摩擦等非线性效应的影响,对"S"型骨架层结构建立三维有限元模型,进行了单外压作用下的压溃失效分析和单一轴向拉力作用下的拉伸失效分析,而后开展轴向拉力和外压载荷组合作用下骨架层压溃失效分析.结果表明轴向拉力会一定程度上降低骨架层压溃承载力,相关结论可以为柔性软管结构设计和完整性评价提供参考. 相似文献
8.
脐带缆作为水下生产系统的“神经生命线”,是水下生产系统的关键一环,其可靠性问题越来越受到关注。影响脐带缆可靠性的事件具有随机性,目前缺乏对这些随机事件发生概率的统计,难以直接对其可靠性进行定量分析。基于模糊数理论和故障树结合的方法对脐带缆可靠性进行分析,首先获得引起脐带缆失效的40个最小割集及底事件重要度排序。其次采用基于模糊集理论的定量分析对脐带缆故障树系统中的底事件进行统计计算,得到各底事件的失效概率,最终计算出顶事件概率,并得出导致脐带缆失效的主要因素依次为护套/铠装失效、钢管失效、电缆失效,为脐带缆的安全运行提出适当的建议。 相似文献
9.
高温高压下海底管道的整体屈曲稳定性分析是管道设计的重要组成部分,而选取多长的管道进行分析对其整体屈曲稳定性结果影响显著。依据临界管长将管道分为"长管"与"短管",基于动力显式分析方法,揭示了长管与短管在发生整体屈曲过程中,屈曲幅值与波长、管壁轴向压力、轴向应变及轴向位移的变化规律;研究了土体约束力影响管道临界长度的规律性,分析了土体约束力系数对长管与短管整体屈曲变形的影响。研究发现,土体约束力对短管的整体屈曲行为影响显著,短管的整体屈曲幅值随土体约束力系数的增大呈现先增大后减小的趋势。该项研究对区分不同长度管道的整体屈曲类型进而采取有效防控措施具有重要参考价值。 相似文献
10.
水下生产系统防沉板结构形式改进研究 总被引：1，自引：0，他引：1
防沉板是水下生产系统的重要基础形式,在海洋工程开发中有着广泛应用。基础承载能力不仅决定防沉板的适用范围,还关乎水下生产系统的稳定性与安全性。运用有限元软件ABAQUS,建立防沉板与土体的相互作用模型,通过平衡初始地应力,设置主从接触,施加重力荷载与位移约束,用Swipe法对不同结构形式防沉板进行数值模拟。比较分析多种防沉板在复合加载模式下的极限复合承载能力差异,讨论了单轴竖向承载力、V-H、H-M荷载空间破坏包络线。计算结果显示,防沉板是否有底部结构、底部结构的形式、布置以及深度对荷载位移曲线以及破坏包络线有着显著的影响。提出了通过改进防沉板结构形式以克服承载力不足的问题的建议,为拓宽防沉板的运用领域提供了参考。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
13.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
14.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
15.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
16.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
Shigehisa Nakamura 《Marine Geodesy》2000,23(1):55-61
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone. 相似文献
19.
The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics. 相似文献
20.