共查询到20条相似文献，搜索用时 62 毫秒
1.
研究ｐＨ和Ｃａ（Ⅱ）对砷酸根在海水与ＮａＣｌ介质中对水合氧化物和粘土矿物上交换吸附的影响：（１）在酸性条件下和海水及ＮａＣｌ介质中，砷酸根在针铁矿上的交换率Ｅ（％）—ｐＨ曲线呈平顶峰型、在δ－ＭｎＯ呈峰型、在粘土上分别呈双峰型和肩峰型。这是砷酸根存在多种形式与固体表面发生离子／配位子交换以及介质中阴离子竞争交换吸附共同作用的结果。（２）在碱性条件下的海水介质中，砷酸根与水合氧化物和粘土矿物的Ｅ（％）—ｐＨ曲线都呈Ｖ型，这是因为生成了具有一定结构的液—固界面三元络合物之故。（３）在ＮａＣｌ介质中，Ｃａ加入起促进作用，再次证明液—固界面三元络合物生成机理与Ｖ型曲线的内在关系 相似文献
2.
实验研究海水中天然溶解有机物（ＤＯＭ）在δ－ＭｎＯ２、粘土和二氧化硅上的吸附,海水中溶解有机碳（ＤＯＣ）在δ－ＭｎＯ２、高岭石、伊利石和二氧化硅上的吸附率随ｐＨ的增加而减小。结果表明,在天然海水ｐＨ８．１条件下,海水中天然溶解有机物在这４种固体粒子上的吸附率大小为：δ－ＭｎＯ２（３２％）＞伊利石（１４％）＞高岭石（４％）≈二氧化硅（３％）。根据统计热力学方法得到的公式能够很好地拟合海水中ＤＯＭ在固体颗粒物上的吸附。 相似文献
3.
研究了ｐＨ 和总钼酸根浓度对海水中钼酸根在针铁矿上吸附的影响。钼酸根在针铁矿上的吸附等温线为Ｓ型。假设海水中钼酸根在针铁矿表面的吸附,是在双电层的内Ｈｅｌｍｈｏｌｔ 层中的能量相等的不同位置上进行的,并考虑到吸附的钼酸根之间存在着横向相互作用,由此推导得到的吸附等温式可描述钼酸根在针铁矿上的Ｓ型吸附等温线,并计算得到钼酸根在针铁矿上的最大吸附量为４ ．７６ ×１０－ ５ｍｏｌ／ｇ。钼酸根在针铁矿上的吸附受溶液ｐＨ影响,吸附密度随ｐＨ 的增加而降低。加入到海水中的钼约有２０ ％ 可被水合氧化铁的清除作用所转移。 相似文献
4.
5.
实验测定了海水中氨基酸存在下Ｃｕ（Ⅱ）在ｒ－ＭｎＯＯＨ上吸附的等温线、Ｃｕ（Ⅱ）％－－ｐＨ曲线和Ｃｕ（Ⅱ）％－氨基酸深度曲线。结果表明，较低浓度氨基酸对Ｃｕ（Ⅱ）在ｒ－ＭｎＯＯＨ上吸附没有影响，而较高浓度氨基酸却起抑制作用，这主要是由于海水中Ｃｕ（Ⅱ）－氨基酸络合反应与ｒ－ＭｎＯＯＨ竞争Ｃｕ（Ⅱ）所致。此外，海水中较高浓度氨基酸只使Ｃｕ（Ⅱ）在ｒ－ＭｎＯＯＨ上吸附的表面分级离子交换稳定常数Ｋｉ（ｉ 相似文献
6.
改性膨润土对赤潮落种及海水中DRP,COD的去除效应 总被引：3，自引：0，他引：3
实验室研究了不同条件制备的改性膨润土对赤潮生物及海水中ＤＲＰ,ＣＯＤ的去除效应,结果表明,改性膨润土有效Ａｌ为１．５％时去除效应最好,经Ｎａ２ＳＯ４,Ａｌ２（ＳＯ４）３改性的膨润土在ｐＨ＝５．５时去除效应最佳,改性膨润土的去除效率随Ａｌ／ＳＯ４比值增加而增加,改性膨润土添加絮凝剂醋甲壳质和Ｃａ（ＯＨ）２提高了去除功效。 相似文献
7.
本文以人工海水和天然海水为介质，研究了Ｃｒ（Ⅲ）被Ｈ２Ｏ２的氧化作用，结果表明，Ｃｒ（Ⅲ）的氧化速率为介质ｐＨ和温度的函数；海水中溶解有机质的存在也将影响Ｃｒ（Ⅲ）的氧化速率，随着海水中腐殖质浓度的增加其氧化速率呈现下降趋势。其原因可解释为腐殖质对Ｃｒ（Ⅲ）的配合作用和对Ｃｒ（Ⅵ）的还原－催化作用。 相似文献
8.
前 言 海洋中溶解有机碳的浓度一般为0.5～2(×10~(-6)),只是海水中无机物的1/10~5,此外尚有更少的固体粒状有机物.海水中有机物的存在量虽然不大,但在许多场合下起着很重要的作用,特别是在液-固界面相互作用中可能起关键作用.许多研究表明,天然水中的颗粒物能显著地吸附有机物,并且在吸附有机物后使其表面带有负电荷,吸附的有机物对微量金属元素的吸附和天然颗粒物的凝聚有着十分重要的影响.因此,研究有机物在悬浮颗粒物上的吸附作用也就显得十分必要. 相似文献
9.
条斑紫菜对无机碳的利用 总被引：4，自引：0，他引：4
于１９９８年３月在青岛太平角采集条斑紫菜,在室内光照强度为１２０μＥ／（ｍ~２·ｓ）的培养架上培养,通过测定其光合作用引起密闭海水体系ｐＨ值及无机碳浓度的变化,借助于各种无机碳利用的抑制剂（Ａｚ、Ｖａｎ、ＤＩＤＳ、ＳＩＴＳ）对其无机碳利用机制进行了研究。结果表明,（１）条斑紫菜可间接吸收ＨＣＯ~（－）_（３）。胞外碳酸醉酶（ＣＡ）催化ＨＣＯ~（－）_（３）水解成ＣＯ_２扩散进入胞内是条斑紫菜无机碳利用的主要形式,占全部无机碳利用的７３％以上。Ａｚ是胞外ＣＡ的抑制剂,可直接检测胞外ＣＡ的存在,它不能透过细胞膜。（２）条斑紫菜可依赖于细胞膜上ＡＴＰ酶对ＨＣＯ~（－）_（３）直接转运。但未发现带Ⅲ蛋白（ｂａｎｄ ３ Ｐｒｏｔｅｉｎ）及 Ｎａ~＋／ＨＣＯ_（３）~（－）协同转运系统的参与。（３）条斑紫菜ｐＨ值补偿点为９．８３,ＣＯ_２补偿点为０．０４μｍｏｌ／Ｌ。 相似文献
10.
海水pH对疏浚物中重金属释放的影响 总被引：2，自引：0，他引：2
对厦门员当湖污染疏浚物中的Ｃｄ，Ｃｕ和Ｐｂ在不同ｐＨ的天然海水中溶出的模拟研究结果表明：在ｐＨ为５．０，６．５，８．３条件下，疏浚物中的Ｃｄ，Ｃｕ，Ｐｂ的释放率分别为８０％－９４％，４％－９％和１．０％－２．２％；在相同条件下，Ｃｄ，Ｃｕ，Ｐｂ的释放量（释放量）均随ｐＨ值增大而减少，释放量的顺序为Ｃｄ＞Ｃｕ＞Ｐｂ。讨论了ｐＨ对释放作用的影响及释放过程所遵循的动力学规律。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
13.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
14.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
15.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
16.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
Shigehisa Nakamura 《Marine Geodesy》2000,23(1):55-61
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone. 相似文献
19.
The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics. 相似文献
20.