共查询到20条相似文献，搜索用时 203 毫秒
1.
2.
承德钢铁公司黑山铁矿矿山爆破地震动效应 总被引：1，自引：0，他引：1
根据河北省黑山铁矿矿山４次爆破地震动效应的观测结果，给出了爆破地震动的强度预测、炸药量与爆破安全距离的关系式，以及炸药能量转换为地震波的能量的转换系数、爆破地震烈度等。 相似文献
3.
通过研究打桩公式法和应力波动法（如CASE法），提出单次冲击能量及P-S曲线测桩法:用重锤或小型火箭筒一次冲击桩顶，用桩顶附近的检波器记录振波图和检测静、动位移. 通过实测冲击能(总能量)转换系数、波动和振动各自消耗的能量等各物理量，测定计算单桩竖向承载力. 利用振波图计算力（P）与位移（S）动态关系曲线，确定屈服点，并利用静载荷试验检验动测结果和确定动静P-S曲线的相关常数，进而确定与承载力相应的沉降量. 而且，可由PS曲线的形态判定桩身成型质量. 相似文献
4.
2008年3月4日在台湾东北部的N3爆破点实施了两次爆破。第一次3000kg炸药的爆破编号为N3P,第二次750kg炸药的爆破编号为N3。为了记录这两次爆破,我们使用了8个三轴旋转传感器、13个三轴加速度计以及12个装有全球定位系统接收器的6通道24位数据记录仪在爆破前后几小时进行连续观测。这些仪器安装在距离爆破点250m(1个台)、500m(11个台)、600m(1个台)的地方,其中距离爆破点500m的11个台站形成了台站间距约为5m的中心台阵。除一个旋转传感器外,都得到了量程内的记录。尽管N3P爆破使用的炸药是N3爆破的4倍,但是13个台站记录的N3P爆破的平移加速度和旋转速度的峰值却只有N3爆破的1.5倍。在台站间距大约5m的中心台阵的记录中,我们还发现平移加速度和旋转速度变化很大(百分之几十)。N3P和N3爆破的最大峰值旋转速度分别为2.74mrad/s和1.75mrad/s。本文的主要目的是报告台湾这两次爆破的旋转和平移运动记录,并在网上发布以开放访问。Langston等(2009)已经对本次试验的平移加速度数据进行了分析,我们计划未来发表一篇关于分析旋转速度数据的文章。 相似文献
5.
为了避免福岭采石场爆破施工对周边民房的影响,布设4个测试点,对不同药量及距离产生的爆破振动给附近民房带来的影响进行监测和分析,得到了振动衰减关系及该采石场爆破施工对附近民房影响的安全距离。当保护对象距离为200 m时,96 kg药量,振动速度为0.45 cm/s,达到土坯房和毛石房屋容许振动的上限值。 相似文献
6.
为了分析一次性爆破拆除多栋建筑造成的地面振动的特征及对周边建筑物的影响,对武汉交通学校群楼爆破拆除中的地面振动进行了测量,并对实测的塌落振动的峰值、频谱特性进行分析。结果表明:此次监测记录到的峰值频率在5～10 Hz,对比高架桥以及单一高层结构爆破拆除数据,倒塌叠加使得振动能量在频谱上分布更加离散,其峰值频率与周边结构自振频率相差变大,周边建筑共振的危险性降低;对于周围的结构而言,水平振动持时大于竖向振动,但水平振动幅值明显小于竖向振动;爆破塌落振动的竖向分量对周围结构的威胁较大,应采取有效的缓冲及隔振措施;由《爆破安全规程》和周边建筑爆破前后主振频率分析可知,本次爆破拆除工作未对周边建筑造成破坏性影响,验证了群楼爆破拆除方案的高效性和安全性。 相似文献
7.
8.
为了模拟近场强地震动，采用了基于有限断层模型的一种随机合成方法．震源破裂面被剖分成一定数量的子源，总的地震矩分成数量更多的子震的矩．一给定子源中一次子震引起的场地地震动的傅氏谱，通过考虑点源的谱、随着距离的衰减、能量耗散及近地表效应等导出．据此幅值谱和一个随机相位谱，并与一个时程包络函数结合，合成一个子震时程．将各子源中各个子震引起的所有时程叠加，得出场地的地震动时程．叠加中，各子震时程之间的时滞，据子震发震时差和子源至场地的距离差别引起的时差确定．对一个设定地震，选用4个断层面倾角，计算了近场21个地点的地震动．结果表明，本文方法可以很好地表达破裂的方向性效应和上盘效应．为了验证方法的可靠性，对1994年美国北岭地震中3个近断层台站MCN，LV3和PCD模拟的地震动与实际记录的加速度反应谱和时程作了比较． 相似文献
9.
讨论了爆破地震产生的地震波传播规律 ,以及地振动信号和仪器记录的电信号之间的关系。在此基础上 ,论述了振动影响测试的原理 ,记录仪器系统的标定以及从观测信号中消除仪器影响的方法。对云南某水电站主厂房施工中的爆破振动进行了测试 ,讨论了爆破地震测试中应注意的问题 相似文献
10.
11.
Study of blasting vibrations in Sarcheshmeh copper mine 总被引：1，自引：0，他引：1
K. Najm) A. Javaherian) H. B. Amnieh) ) Department of Mining Metallurgy Petroleum Engineering Amirkabir University Tehran I R Iran ) Institute of Geophysics Tehran University Tehran I R Iran 《地震学报(英文版)》2002,15(6):683-690
Introduction In spite of development of mechanized methods of ground excavation, drilling and blasting is still extensively employed because of its low capital investment and simplicity. Its extensive use is not even limited by extension of mines close to residential areas and vital establishments. If it is not used in a controlled way, blasting operation can cause instability, failure of mine slopes and damps and damage to the nearby structures. The main objective here could be to reduce the … 相似文献
12.
M. Monjezi M. Ahmadi M. Sheikhan A. Bahrami A.R. Salimi 《Soil Dynamics and Earthquake Engineering》2010
Prediction of vibration is very important in mining operations as well as civil engineering projects. In this paper, multi layer perceptron neural network (MLPNN), radial basis function neural network (RBFNN) and general regression neural network (GRNN) were utilized to predict ground vibration level in a Sarcheshmeh copper mine, Iran. It was observed that the MLPNN gives the best results. For this technique root mean square error and coefficient of correlation were found 0.03 and 0.954, respectively. Sensitivity analysis showed that distance from the blast, number of holes per delay and maximum charge per delay are the most effective parameters in making ground vibration in the blasting operation. 相似文献
13.
Ground vibrations induced by blasting are one of the fundamental problems in the mining industry and may cause severe damage to structures and plants nearby. Therefore, a vibration control study plays an important role in the minimization of environmental effects of blasting in mines. This paper presents the results of ground vibration measurement induced by bench blasting at Magnesite Incorporated Company (MAS) open pit mine in Turkey. The scope of this study is to predict peak particle velocity and to determine the slope of the attenuation curve for this site. For this purpose, the blasting parameters of 43 shots were carefully recorded and the ground vibration components were measured for each event. After carrying out statistical analysis, the site specific parameters were determined to predict the peak particle velocity. In the light of this analysis, the prediction graphics of maximum charge weight per delay versus distance for different damage criteria was proposed to be able to perform controlled blasting in order not to damage to the nearby structures, especially to the plant where rotary and shaft kilns have been established. 相似文献
14.
15.
The results from an experimental blasting program that was performed at the special explosives training field of the General Directorate of Security in Ankara, where new residential blocks are planned to be constructed nearby, are presented. With the objective of estimating the blast-induced ground vibration effects on the proposed structures, various blasting parameters of nineteen surface and underground explosions were recorded in two directions at three measurement stations. Site-specific empirical relationships between peak particle velocity, the amount of explosive and the distance were developed. These relationships were used to construct a practical blasting chart, which gives the maximum amount of explosive to be used as a function of distance, for future underground and surface blasting operations in the training field. Since the use of peak particle velocity in the field of civil engineering has been limited so far, site-specific parameters were also estimated to predict the blast-induced horizontal peak ground acceleration. Then, an attempt was made to investigate the dynamic responses of four and six storey reinforced concrete structures that consist of frame and shear wall type structural systems under the measured accelerations using finite element analysis. The limitations of this approach were discussed within the context of damage estimation. 相似文献
16.
Ali Kahriman 《Soil Dynamics and Earthquake Engineering》2004,24(11):887-892
The aim of this study is to predict peak particle velocity level at a limestone quarry located in Istanbul, Turkey. The ground vibration components were measured for 73 blast events during the bench blast optimization studies during a long period. In blasting operations; ANFO (blasting agent), gelatine dynamite (priming) and NONEL detonators (firing) were used as explosives at this site. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured by means of vibration monitors for every event. Then, the data pairs of scaled distance and particle velocity were analyzed. The equation of scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity. At the end of statistical evaluations, an empirical relationship with good correlation was established between peak particle velocity and scale distance for this site. The established relationship and the results of the study are presented. 相似文献
17.
The present paper mainly deals with the prediction of blast-induced ground vibration level in Bakhtiary formation at intake of waterway system in Gotvand dam, Iran. For this research the ground vibration components were recorded carefully by means of 3 sets of vibration monitors for 32 blast events during the bench blasting in front of tunnels. Then, the data pairs of scaled distance and particle velocity were analyzed by using the USBM equation. At the end of statistical evaluations, a relationship between peak particle velocity and scaled distance for this site was established with good correlation. Again, other data measurements during tunnel excavation near concrete structures were used to validate the predicted PPV and optimize the blasting patterns to omit the effects of resonance and vibration in USBM (RI-8507) standard. Based on the vibration tests done in Bakhtiary conglomerate, constant dynamic factors of the rock mass related to vibration velocity are 159.07 and 1.077. 相似文献
18.
青岛地铁工程爆破振动效应分析 总被引：4，自引：0，他引：4
本文根据大量现场观测资料研究了青岛地铁施工爆破引起的地面振动效应,分析了炸药类型,药量,爆心距,施工爆破方法以及地质条件等因素对爆破振动效应的影响,总结了青岛地铁施工爆破所引起的地面振动强度的一般规律,为施工中的爆破优化设计和爆破振动控制提供了依据。 相似文献
19.
Blasting induced vibration is one of the fundamental problems in the open-pit mines and intense vibration can cause critical damage to structures and plants nearby the open-pit mines, especially to the final pit wall's stability. It is very important to study how to control vibration induced by blasting in the mitigation of negative effects of blasting in open-pit mines. This study aims to examine the propagation of blasting induced ground vibrations and find the feasible approaches to reduce the harmful effects of vibrations induced by blasting on the final pit wall's stability. For this purpose, a series of field experiments were conducted in XinQiao Mining Co. Ltd. Sixty-six events and the blasting parameters of these shots were carefully recorded. During the statistical analysis of the collected data, the predictor equation proposed by the United States Bureau of Mines (USBM) was used to establish a relationship between the Peak Particle Velocity (PPV) and the Scaled Distance (SD) factor. The relationship between PPV and SD was determined and proposed to be used in this open-pit mine. Control of maximum charge amount per delay and the selection optimum interval time to reduce the intensity of vibration by waveform interference were applied in practice. Based on the field experiments, we can determine the maximum charge amount per delay and 15 ms delay were proposed to be used in this site, and a decrease in vibration of 24.5% was obtained. 相似文献
20.
在城市浅埋地铁爆破开挖中,经常遇到地下管网、涵洞等构筑物,而爆破地震效应对其影响范围和程度的正确评价就显得尤为重要。本文以长沙地铁爆破开挖为例,以现场实测数据为基础,采用有限单元法,对爆破振动下大直径混凝土污水管道的动力响应、变形和动应力等进行了计算,评价了爆破地震对管道的安全影响。研究表明:管道在控制爆破作用下是偏于安全的;爆心距是影响管道受到爆炸作用力影响大小的最主要因素;对于以实测数据为基础,采用加速度激励的时程分析方法以爆破振动对埋地管道的影响进行评价,是一种可行且较为精确的方法。 相似文献