首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
为提高装配式钢结构梁柱节点的抗震性能,首先通过熔融共混法制备高阻尼性能纳米偏高岭土/氟橡胶(NanoGmetakaolin/Fluororubber,NMK/FKM)复合材料,并对该新型材料进行4种频率下的动态力学性能试验和静态力学试验,然后以 NMK/FKM 纳米复合材料为核心耗能材料,对所提出的直角型黏弹性阻尼器进行 ABAQUS有限元模拟分析.研究结果表明:当频率为1.5Hz 时,NMK/FKM 纳米复合材料宽阻尼温域和 TA 值皆达到峰值,该工况下材料的阻尼性能最佳;直角型黏弹性阻尼器表现出刚度随位移幅值的增大而增大的动力特性;当频率为0.5、1.0和1.5Hz 时,阻尼器滞回特性表现出非线性特征,当频率升至2.0Hz时,滞回特性则为线性.随着黏弹性材料层厚度的增大,滞回环面积、阻尼器刚度和最大阻尼力逐渐减小;随着高跨比的增大,阻尼器耗能性能提升.通过调整阻尼器的高跨比和阻尼材料层厚度,可以进一步提高直角型阻尼器的动态响应.  相似文献   

2.
在混凝土空心砌块的空腔中填入橡胶砂形成的组合砌块(RSMCB)可作为简易隔震层应用于村镇建筑防震减灾。建立RSMCB的三维数值分析模型,进行循环剪切试验以及隔震分析,研究不同橡胶砂配比、竖向压应力、盖板尺寸和盖板埋深对隔震砌块动刚度和阻尼比的影响,分析不同的上部配重、输入地震波、橡胶砂配比、盖板尺寸和铺设方式对RSMCB垫层隔震效果的影响。结果表明:(1)橡胶砂芯组合砌块应变软化现象明显。(2)RSMCB的水平动刚度随橡胶砂配比增大而减小,随盖板埋深、盖板尺寸以及竖向压应力的增大而增大。(3)阻尼比随橡胶砂配比、竖向压应力、盖板尺寸和埋深的增大而减小,橡胶砂芯组合砌块隔震消能效果显著。在隔震数值模拟中,输入加速度在经过橡胶砂芯组合砌块垫层过滤后均有不同程度的降低,且被过滤掉大部分高频波。隔震效应随着盖板尺寸的增大而减小,上部结构配重越大,隔震效应越明显,橡胶砂配比为30%时RSMCB垫层隔震效应更好。橡胶砂芯组合砌块符合在村镇欠发达地区低成本隔震的要求,表现出广阔的应用前景。  相似文献   

3.
研究不同高径比橡胶基底隔震储罐的频率特征,探讨储罐隔震体系3种不同振动频率随支座隔震频率变化规律.分析在不同频谱特性地震波激励下,隔震体系各振型组分对地震响应(基底剪力、支座位移和晃动波高)的影响,以及响应峰值随支座隔震频率和阻尼比的变化特点.研究表明,基底剪力峰值与场地地震波频谱特性密切相关.支座隔震频率不能完全反映减震机理的实质,隔震振型频率是影响基底剪力的重要参数.在软弱场地上隔震储罐的减震效率低,有效隔震频率范围窄.晃动波高峰值是储罐自振特性和地震波频谱特性等多种因素导致的结果,隔震系统设计时需特别考虑晃动波高增大的影响.  相似文献   

4.
Viscoelastic dampers are now among some of the preferred energy dissipation devices used for passive seismic response control. To evaluate the performance of structures installed with viscoelastic dampers, different analytical models have been used to characterize their dynamic force deformation characteristics. The fractional derivative models have received favorable attention as they can capture the frequency dependence of the material stiffness and damping properties observed in the tests very well. However, accurate analytical procedures are needed to calculate the response of structures with such damper models. This paper presents a modal analysis approach, similar to that used for the analysis of linear systems, for solving the equations of motion with fractional derivative terms for arbitrary forcing functions such as those caused by earthquake induced ground motions. The uncoupled modal equations still have fractional derivatives, but can be solved by numerical or analytical procedures. Both numerical and analytical procedures are formulated. These procedures are then used to calculate the dynamic response of a multi-degree of freedom shear beam structure excited by ground motions. Numerical results demonstrating the response reducing effect of viscoelastic dampers are also presented.  相似文献   

5.
Although the seismic actions generally consist of a combination of waves, which propagates with an angle of incidence not necessarily vertical, the common practice when analyzing the dynamic behavior of pile groups is based on the assumption of vertically incident wave fields. The aim of this paper is to analyze how the angle of incidence of SV waves affects the dynamic response of pile foundations and piled structures. A three-dimensional boundary element-finite element coupling formulation is used to compute impedances and kinematic interaction factors corresponding to several configurations of vertical pile groups embedded in an isotropic homogeneous linear viscoelastic half-space. These results, which are provided in ready-to-use dimensionless graphs, are used to determine the effective dynamic properties of an equivalent single-degree-of-freedom oscillator that reproduces, within the range where the peak response occurs, the response of slender and nonslender superstructures through a procedure based on a substructuring model. Results are expressed in terms of effective flexible-base period and damping as well as maximum shear force at the base of the structure. The relevance and main trends observed in the influence of the wavefront angle of incidence on the dynamic behavior of the superstructure are inferred from the presented results. It is found that effective damping is significantly affected by the variations of the wave angle of incidence. Furthermore, it comes out that the vertical incidence is not always the worst-case scenario.  相似文献   

6.
As high‐rise buildings are built taller and more slender, their dynamic behavior becomes an increasingly critical design consideration. Wind‐induced vibrations cause an increase in the lateral wind design loads, but more importantly, they can be perceived by building occupants, creating levels of discomfort ranging from minor annoyance to severe motion sickness. The current techniques to address wind vibration perception include stiffening the lateral load‐resisting system, adding mass to the building, reducing the number of stories, or incorporating a vibration absorber at the top of the building; each solution has significant economic consequences for builders. Significant distributed damage is also expected in tall buildings under severe seismic loading, as a result of the ductile seismic design philosophy that is widely used for such structures. In this paper, the viscoelastic coupling damper (VCD) that was developed at the University of Toronto to increase the level of inherent damping of tall coupled shear wall buildings to control wind‐induced and earthquake‐induced dynamic vibrations is introduced. Damping is provided by incorporating VCDs in lieu of coupling beams in common structural configurations and therefore does not occupy any valuable architectural space, while mitigating building tenant vibration perception problems and reducing both the wind and earthquake responses of the structure. This paper provides an overview of this newly proposed system, its development, and its performance benefits as well as the overall seismic and wind design philosophy that it encompasses. Two tall building case studies incorporating VCDs are presented to demonstrate how the system results in more efficient designs. In the examples that are presented, the focus is on the wind and moderate earthquake responses that often govern the design of such tall slender structures while reference is made to other studies where the response of the system under severe seismic loading conditions is examined in more detail and where results from tests conducted on the viscoelastic material and the VCDs in full‐scale are presented. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

7.
In conventional modal analysis procedures, usually only a few dominant modes are required to describe the dynamic behavior of multi-degrees-of-freedom buildings. The number of modes needed in the dynamic analysis depends on the higher-mode contribution to the structural response, which is called the higher-mode effect. The modal analysis approach, however, may not be directly applied to the dynamic analysis of viscoelastically damped buildings. This is because the dynamic properties of the viscoelastic dampers depend on their vibration frequency. Therefore, the structural stiffness and damping contributed from those dampers would be different for each mode. In this study, the higher-mode effect is referred to as the response difference induced by the frequency-dependent property of viscoelastic dampers at higher modes. Modal analysis procedures for buildings with viscoelastic dampers distributed proportionally and non-proportionally to the stiffness of the buildings are developed to consider the higher-mode effect. Numerical studies on shear-type viscoelastically damped building models are conducted to examine the accuracy of the proposed procedures and to investigate the significance of the higher-mode effect on their seismic response. Two damper models are used to estimate the peak damper forces in the proposed procedures. Study results reveal that the higher-mode effect is significant for long-period viscoelastically damped buildings. The higher-mode effect on base shear is less significant than on story acceleration response. Maximum difference of the seismic response usually occurs at the top story. Also, the higher-mode effect may not be reduced by decreasing the damping ratio provided by the viscoelastic dampers. For practical application, it is realized that the linear viscous damping model without considering the higher-mode effect may predict larger damper forces and hence, is on the conservative side. Supported by: Science Council, Chinese Taipei, grant no. 88-2625-2-002-006  相似文献   

8.
An exact analysis for two-dimensional dynamic interaction of monochromatic progressive plane compressional and shear seismic waves with a permeable circular tunnel lining of circumferentially varying wall thickness buried in a boundless porous elastic fluid-saturated formation is presented. The novel features of Biot dynamic theory of poroelasticity in conjunction with the translational addition theorems for cylindrical wave functions, along with the appropriate wave field expansions and the pertinent boundary conditions are employed to develop a closed-form solution in form of infinite series. The analytical results are illustrated with numerical examples in which an air-filled and water-saturated permeable tunnel lining of variable wall thickness, embedded within water-saturated surrounding formations of distinct frame properties (soft, stiff, and stiff viscoelastic soil), is insonified by fast compressional or shear waves at selected angles of incidence. The effects of liner eccentricity, interface permeability, formation material type, incident wave frequency, and angle of incidence on the hoop stress amplitude are evaluated and discussed for representative values of the parameters characterizing the system. Limiting cases are considered and good agreements with the solutions available in the literature are obtained.  相似文献   

9.
Viscoelastic dampers, as supplementary energy dissipation devices, have been used in building structures under seismic excitation or wind loads. Different analytical models have been proposed to describe their dynamic force deformation characteristics. Among these analytical models, the fractional derivative models have attracted more attention as they can capture the frequency dependence of the material stiffness and damping properties observed from tests very well. In this paper, a Fourier-transform-based technique is presented to obtain the fractional unit impulse function and the response of structures with added viscoelastic dampers whose force-deformation relationship is described by a fractional derivative model. Then, a Duhamel integral-type expression is suggested for the response analysis of a fractional damped dynamic system subjected to deterministic or random excitation. Through numerical verification, it is shown that viscoelastic dampers are effective in reducing structural responses over a wide frequency range, and the proposed schemes can be used to accurately predict the stochastic seismic response of structures with added viscoelastic dampers described by a Kelvin model with fractional derivative.  相似文献   

10.
为改善高层建筑联肢剪力墙抗震性能,消除传统连梁阻尼器残余位移较大或等效阻尼比较小等问题,设计了一种兼具耗能和自复位功能的形状记忆合金粘弹性连梁阻尼器(Shape Memory Alloy Viscoelastic Coupling Beam Damper,SVCBD),给出了新型连梁阻尼器的构造形式和工作原理。利用拉普拉斯变换得到的粘弹性材料粘性系数以及超弹性形状记忆合金(Shape Memory Alloy,SMA)本构模型,基于ABAQUS仿真平台建立了SVCBD精细有限元模型;对SVCBD滞回特性进行了模拟分析,并与普通粘弹性阻尼器进行了对比。考虑了SMA丝束初始预应力度、横截面总面积和粘弹性材料层剪切面积等参数对SVCBD滞回特性的影响。分析结果表明:与普通粘弹性连梁阻尼器(Viscoelastic Coupling Beam Damper,VCBD)相比,SVCBD滞回曲线更加饱满,耗能能力更强,残余位移减小,初始刚度也大大提高,具有很好的耗能和复位效果;SMA丝束初始预应力大小、横截面面积(即配置数量)和粘弹性材料层剪切面积均对SVCBD的耗能和复位能力具有明显的影响。  相似文献   

11.
Coupling adjacent buildings using discrete viscoelastic dampers for control of response to low and moderate seismic events is investigated in this paper. The complex modal superposition method is first used to determine dynamic characteristics, mainly modal damping ratio and modal frequency, of damper-linked linear adjacent buildings for practical use. Random seismic response of linear adjacent buildings linked by dampers is then determined by a combination of the complex modal superposition method and the pseudo-excitation method. This combined method can effectively and accurately determine random seismic response of non-classically damped systems in the frequency domain. Parametric studies are finally performed to identify optimal parameters of viscoelastic dampers for achieving the maximum modal damping ratio or the maximum response reduction of adjacent buildings. It is demonstrated that using discrete viscoelastic dampers of proper parameters to link adjacent buildings can reduce random seismic responses significantly. Copyright © 1999 John Wiley & Sons Ltd.  相似文献   

12.
基于应用透射人工边界条件的显式有限元法计算断层破碎带宽度及力学参数变化、地震动入射角变化时二维断层场地模型P波入射下地表地震动场的分布。结果表明:(1)低速度破碎带的存在导致整个场地都有P波转换为SV波的分量,且在断层破碎带的区域出现断层陷波;(2)低速度破碎带的存在使输入场地恒定的能量向破碎带集聚放大,随着破碎带宽度增大或其介质波速降低集聚放大效应增大;(3)场地放大效应是频率相关的,宽度较宽或介质波速较低的断层破碎带对输入地震动中较低的频率成份放大显著;(4)竖向断层破碎带能阻隔斜入射地震P波,随着入射角增加隔震效应更显著。  相似文献   

13.
This paper deals with the free-field response of the in-plane motion resulting from a combination of inclined incident body waves. The amplification of waves in a viscoelastic layer with stochastic changes in the elastic properties and density is investigated. The method used is that of Karal and Keller and is based on the idea of the fundamental matrix. The third order correlations are neglected. The resulting integro-differential equations for the average displacements are solved by the Laplace transform. Generally, analysis indicates that the stochastic changes in the shear modulus and density enhance the damping in a significant manner. However, increases in the waves' amplification can arise in the case of a small dimensionless frequency and uncorrelated stochastic changes of material parameters.  相似文献   

14.
粘弹性阻尼器是有效的被动消能装置,普通粘弹性阻尼器的力学性能主要受环境温度、激励频率和应变幅值的影响,对结构的设计结果会产生偏差.新型粘弹性阻尼材料,其力学性能不受环境温度和激励频率的影响,通过与普通粘弹性阻尼器动态力学性能的对比,可见新型粘弹性阻尼器作为耗能元件,对消能减震结构的设计结果会比较精确.  相似文献   

15.
基于土体的等效粘弹性模型,结合场地典型剖面的土体特性以及室内实验确定的各力学参数,采用时域积分和迭代的方法研究了沁河倒虹吸管道在地震作用下的反应,分析了管道截面中间底部点绝对地震位移、顶部点相对于底部点的地震动位移及管道动静综合主应力的变化规律;并根据有限元时程法的分析结果,按照混凝土承载能力极限状态设计式,对管身混凝土的抗拉、抗压安全度进行校核。结果表明,在人工地震波、调整后的E1 Centro和Pulgas地震波分别输入的情况下沁河渠道倒虹吸管道均满足抗震要求。  相似文献   

16.
In order to study the influence of the ground motion spatial effect on the seismic response of large span spatial structures with isolation bearings, a single-layer cylindrical latticed shell scale model with a similarity ratio of 1/10 was constructed. An earthquake simulation shaking table test on the response under multiple-support excitations was performed with the high-position seismic isolation method using high damping rubber(HDR) bearings. Small-amplitude sinusoidal waves and seismic wave records with various spectral characteristics were applied to the model. The dynamic characteristics of the model and the seismic isolation effect on it were analyzed at varying apparent wave velocities, namely infinitely great, 1000 m/s, 500 m/s and 250 m/s. Besides, numerical simulations were carried out by Matlab software. According to the comparison results, the numerical results agreed well with the experimental data. Moreover, the results showed that the latticed shell roof exhibited a translational motion as a rigid body after the installation of the HDR bearings with a much lower natural frequency, higher damping ratio and only 1/2~1/8 of the acceleration response peak values. Meanwhile, the structural responses and the bearing deformations at the output end of the seismic waves were greatly increased under multiple-support excitations.  相似文献   

17.
利用实体软钢棒作为消能限位装置,将一种摩擦性能优良的二硫化钼材料作为隔震支座的滑移材料,提出并制作了一种可以应用于框架结构既能隔震又可以消能的新型摩擦滑移隔震装置。探讨了其设计方法和应用方法,并对安装了该新型摩擦滑移隔震装置的一相似比为1:5的5层框架结构模型进行了振动台试验,测试了框架结构在单向地震波作用下的地震反应规律,分析了摩擦滑移隔震结构的加速度反应、层间剪力反应、隔震层滑移量及隔震层剪力的变化规律。结果表明:一般情况下当设防烈度为8度,Ⅱ类场地时,该隔震结构的加速度响应可降低50%左右,层间剪力响应可降低50%左右,减震效果比较明显。另外,只要确定合理的构造方案和实施方案,这种新型摩擦滑移隔震装置就能满足框架结构的隔震减震要求,可应用于实际工程结构中。  相似文献   

18.
Peak ground acceleration (PGA), frequency content and time duration are three fundamental parameters of seismic loading. This study focuses on the seismic load frequency and its effect on the underground structures. Eight accelerograms regarding different occurred earthquakes that are scaled to an identical PGA and variation of ground motion parameters with ratio of peak ground velocity (PGV) to PGA, as a parameter related to the load frequency, are considered. Then, concrete lining response of a circular tunnel under various seismic conditions is evaluated analytically. In the next, seismic response of underground structure is assessed numerically using two different time histories. Finally, effects of incident load frequency and frequency ratio on the dynamic damping of geotechnical materials are discussed. Result of analyses show that specific energy of seismic loading with identical PGA is related to the seismic load frequency. Furthermore, incident load frequency and natural frequency of a system have influence on the wave attenuation and dynamic damping of the system.  相似文献   

19.
This review type of paper shows how the poroelastodynamic theory of Biot can be applied to some soil dynamics problems encountered in transportation engineering, which have been solved by the present authors. These problems involve rigid walls retaining poroelastic soil and subjected to harmonic seismic waves and moving loads on poroelastic soil. Both classes of problems involve a soil layer over bedrock, are of the plane strain type and are solved analytically by two methods: a direct (almost exact and exact for the above two classes of problems) method and an approximate method. The effects of shear modulus, porosity, permeability and hysteretic damping of the soil medium as well as the seismic frequency for retaining walls and velocity for moving loads on the dynamic response are numerically evaluated in order to assess their relative importance on that response.  相似文献   

20.
Buildings are continually subject to dynamic loads, such as wind load, seismic ground motion, and even the load from internal utility machines. The recent trend of constructing more flexible high‐rise buildings underscores the importance of including viscoelastic dampers in building designs. Viscoelastic dampers are used to control the dynamic response of a building. If the seismic design is based only on the linear response spectrum, considerable error may occur when calculating the seismic response of a building; rubber viscoelastic dampers show non‐linear hysteretic damping that is quite different from viscous damping. This study generated a non‐linear response spectrum using a non‐linear oscillator model to simulate a building with viscoelastic dampers installed. The parameters used in the non‐linear damper model were obtained experimentally from dynamic loading tests. The results show that viscoelastic dampers effectively reduce the seismic displacement response of a structure, but transmit more seismic force to the structure, which essentially increases its seismic acceleration response. Copyright © 2003 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号