共查询到18条相似文献，搜索用时 109 毫秒
1.
2.
3.
4.
反复荷载下钢筋混凝土框架柱杭剪承载力分析 总被引：9，自引：6，他引：3
钢筋混凝土框架柱作为高层房屋建筑的主要承重构件,在历次地震中因框架脆性剪切破坏而造成结构严重损坏甚至倒塌的现象十分常见。本文通过分析有关试验资料,提出了钢筋混凝土框架柱塑性铰区剪切强度的计算公式及有关构造措施,以保证框架柱在一定延性条件下具有足够的抗剪强度,实现“强剪弱弯”的抗震设计原则,使抗震设计的框架结构具有足够的强度和良好的延性,以配合混凝土结构设计规范（ＧＢＪ１０－８９）的修订工作。本文的 相似文献
5.
6.
为保证框架柱端塑性铰达到预期的塑性转动之前,柱端塑性铰区不出现剪切破坏,结合框架柱塑性铰区抗剪承载力的试验研究,利用ANSYS对10个框架柱构件塑性铰区的抗剪性能进行了非线性有限元分析;有限元模型中混凝土采用SOLID65单元,钢筋采用LINK8单元,分离式建模,施加约束时将试验构件上梁上端表面的所有节点在竖直方向耦合,以保证塑性铰出现在柱端;计算了10个构件的骨架曲线,框架柱塑性铰区弹性工作阶段、带裂缝工作阶段和破坏阶段的应力云图和破坏时的裂缝分布图,将以上计算结果与试验结果进行了对比,数值计算结果和试验结果符合良好,验证了有限元模型建立的准确性,所建模型可为今后同类问题的非线性有限元计算提供参考。 相似文献
7.
8.
9.
混凝土框架柱抗剪承载力计算公式的可靠度分析探讨 总被引：1，自引：0，他引：1
通过试验研究，提出了基于能力设计法的框架柱塑性铰区抗剪承载力计算公式，并对此进行了可靠度分析。定量分析了该计算公式的可靠指标与剪跨比、配箍率等因素的关系。同时针对目前我国现行规范抗剪承载力计算的可靠度指标偏低较多的情况，该建议公式对不同抗震要求的构件提出了不同的可靠指标，既考虑了我国设计习惯，又体现了能力设计法的要求，充分考虑了安全性的要求，对工程应用具有较大的参考价值。论文的主要研究成果已被《混凝土结构设计规范》(GB50010-2002)吸收。 相似文献
10.
建立竖板-栓钉连接钢管混凝土（CFST）柱-钢筋混凝土（RC）梁节点试件（SSJD）拟静力加载试验有限元模型,并在节点损伤情况、梁端荷载-位移曲线等数值模拟结果与试验结果吻合较好的基础上,进一步开展了RC梁混凝土强度、配筋率ρs和连接竖板长度Lb及界面连接情况等对CFST柱-RC梁节点梁端塑性铰区域力学性能的影响。研究结果表明,RC梁混凝土强度对试件SSJD塑性铰区域受力性能的影响较小;适筋范围内RC梁配筋率增加可适当提高试件SSJD承载力和延性;随着连接竖板长度的增加,梁端塑性铰区域外移,梁破坏荷载增大;本研究给出的RC梁与CFST柱之间的界面抗剪承载力模拟值与计算值吻合较好,可用于界面抗剪设计。 相似文献
11.
通过对日本抗震设计规范中有关钢筋混凝土框架柱受剪承载力代表性公式的研究，凸现了由经验公式到基于桁架一拱模型建立的发展趋势。对各公式中所包括的影响框架柱受剪承载力的主要因素(如剪跨比、轴压比、配箍率、混凝土强度、纵筋率等)进行了深入讨论，并采用框架柱受剪承载力试验数据考察了各个公式的有效性。 相似文献
12.
Reinforced concrete columns with insufficient transverse reinforcement and non‐seismic reinforcement details are vulnerable to brittle shear failure and to loss of axial load carrying capacity in the event of a strong earthquake. In this paper, a procedure is presented after examining the application of two macro models for displacement‐based analysis of reinforced concrete columns subjected to lateral loads. In the proposed model, lateral load‐deformation response of the column is simulated by estimating flexural and shear deformation components separately while considering their interaction and then combining these together according to a set of rules depending upon column's yield, flexural and shear strengths. In addition, lateral deformation caused by reinforcement slip in beam–column joint regions and buckling of compression bars are taken into account and considered in the analysis. Implementation of the proposed procedure produces satisfactory lateral load–displacement relationships, which are comparable with experimental data. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
13.
编制了碳纤维布加固钢筋混凝土柱的剪力-位移关系全过程分析程序,通过对多种工况下碳纤维布加固钢筋混凝土柱的剪力-位移关系进行大量计算分析,较全面地探讨了碳纤维布配箍特征值、轴压比、剪跨比、箍筋配箍特征值、纵筋配筋率、混凝土强度等参数对碳纤维布加固钢筋混凝土柱的剪力-位移关系及其破坏位移增大系数的影响。在此基础上,给出了碳纤维布加固钢筋混凝土柱破坏位移增大系数的回归计算公式,统计建立了碳纤维布加固钢筋混凝土柱的剪力-位移关系三折线模型中各无量纲特征参数的确定方法。 相似文献
14.
Reinforced concrete (RC) frame structures are one of the mostly common used structural systems, and their seismic performance is largely determined by the performance of columns and beams. This paper describes horizontal cyclic loading tests often column and three beam specimens, some of which were designed according to the current seismic design code and others were designed according to the early non-seismic Chinese design code, aiming at reporting the behavior of the damaged or collapsed RC frame strctures observed during the Wenchuan earthquake. The effects of axial load ratio,shear span ratio, and transverse and longitudinal reinforcement ratio on hysteresis behavior, ductility and damage progress were incorporated in the experimental study. Test results indicate that the non-seismically designed columns show premature shear failure, and yield larger maximum residual crack widths and more concrete spalling than the seismically designed columns. In addition, longitudinal steel reinforcement rebars were severely buckled. The axial load ratio and shear span ratio proved to be the most important factors affecting the ductility, crack opening width and closing ability, while the longitudinal reinforcement ratio had only a minor effect on column ductility, but exhibited more influence on beam ductility. Finally, the transverse reinforcement ratio did not influence the maximum residual crack width and closing ability of the seismically designed columns. 相似文献
15.
Seismic evaluation of the shear behavior in reinforced concrete bridge columns including effect of vertical accelerations 
下载免费PDF全文
下载免费PDF全文 The effect of vertical excitation on shear capacity of reinforced concrete columns is important. Field evidences, analytical studies and static or hybrid simulations suggested that excessive tension or tensile strain of the column may lead to shear strength degradation, and therefore vertical excitation can be one of the causes of shear failure. This paper describes an experimental study consisting of shaking table tests on reduced‐scale bridge columns. Results of the tests indicate that tension in the columns has the potential to degrade the shear capacity, which is mainly due to the degradation of the concrete contribution to this capacity. The presented computational results and code evaluations also support this shear strength degradation. The presented dynamic tests contribute to better understanding of the effect of vertical excitation on the shear failure, which is one of the most critical brittle failure mechanisms. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
16.
基于通用有限元软件ABAQUS,分别在准静态和动态加载条件下,对不同剪跨比和箍筋率的钢筋混凝土柱进行了数值模拟。对比现有试验结果发现,ABAQUS的模拟效果与试验结果吻合较好;加载速率的影响随着剪跨比和箍筋率的增大而降低;钢筋混凝土柱的峰值承载力随着加载速率增大而增大的趋势明显,刚度无明显变化,延性比趋于稳定。因此,在进行地震作用下钢筋混凝土结构的抗震分析时,对加载速率的影响效应要给予足够的考虑。 相似文献
17.
Failure simulation of shear‐critical RC columns with non‐ductile detailing under lateral load 下载免费PDF全文
下载免费PDF全文 Reinforced concrete columns with non‐ductile detailing typically exhibit a softening behavior characterized by severe degradation when subjected to cyclic lateral loads. Whether the response is brittle or ductile, shear failure occurs with an inclined through crack along which sliding occurs coupled with loss of horizontal and vertical load‐bearing capacity of the member. The rapid loss of resistance after the peak strength is reached is because of one or more of the following local failure mechanisms: brittle failure of poorly confined concrete; buckling of longitudinal reinforcing bars because of lack of adequate transverse reinforcement or following opening of stirrups after spalling of cover concrete; bond failure. In this study, a modeling strategy to build a detailed 3D finite element model capable of capturing all of the above‐mentioned local failure mechanisms is presented. In particular, a steel–concrete interface model for representing the interaction within the member between concrete core, cover and longitudinal and transverse reinforcement is proposed. Comparison with results of an experimental test of a shear‐sensitive column demonstrates the effectiveness of the simulation up to failure of the element. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
18.
本文对基于性能的抗震设计方法中最具有代表性的直接基于位移的设计方法在剪力墙结构中的应用进行了研究。采用结构非线性分析程序探讨了墙厚、混凝土强度等级、纵筋配筋率、钢筋级别、轴压比、墙长等因素对单肢剪力墙屈服位移的影响,从而对现有的屈服曲率计算公式进行了改进。另外将按顶点荷载作用下的屈服位移计算公式求出的屈服位移与实际倒三角形荷载作用下的剪力墙屈服位移进行了比较,,从而推导出倒三角形荷载作用下的屈服位移计算公式。 相似文献