共查询到18条相似文献，搜索用时 140 毫秒
1.
2.
3.
地震作用下简支梁桥非线性碰撞分析 总被引：1，自引：0，他引：1
采用能量原理建立了能考虑梁薄壁特性的桥梁上部结构梁段单元动力分析模型,利用非线性接触单元Kelvin碰撞模型,考虑非线性支座的滞回特性(采用W en模型),选择适合不同场地条件的地震波,以京港澳高速公路孟姜女河桥(3跨简支梁桥)为例,进行了桥梁结构纵向碰撞非线性地震响应分析。计算结果表明,随着地震波强度的增加,桥梁上部结构碰撞次数明显增加,结构响应峰值均有所增大;跨间碰撞发生对地震响应值影响较大;伸缩缝间距大小及各跨长度比变化对跨间碰撞效应影响很大;结构碰撞响应对输入地震波具有较强的频谱敏感性;桥梁碰撞计算时桥台铅芯橡胶支座不能简单按简支约束处理。所得结论可供桥梁抗震设计参考。 相似文献
4.
为了准确分析FPS隔震桥梁的纵向地震碰撞反应,针对一典型3跨FPS隔震简支梁桥,建立了考虑FPS双向耦合效应和梁缝处三维碰撞效应的非线性动力计算模型,分析双向地震作用下FPS隔震简支梁桥纵向地震碰撞反应;研究支座半径和摩擦系数对简支梁桥纵向地震碰撞反应的影响规律。研究结果表明:横向地震作用会增大简支梁邻梁间纵向地震碰撞次数和碰撞力,降低墩底纵向剪力;为减小地震碰撞反应,设计时可适当增大支座半径和支座摩擦系数。 相似文献
5.
总结了6种半主动控制算法,采用黏滞阻尼器,对一座三跨简支梁桥进行了不同地震动输入下的半主动控制地震反应计算分析,比较分析了不同地震动输入和半主动控制算法对简支梁桥地震反应控制效果的影响。结果表明,半主动控制能有效地减小桥梁结构的大部分地震反应,同时可能会放大另外部分地震反应,这与地震动输入密切相关,不同地震动输入下的控制效果各不相同。所提六种半主动控制算法中,算法2、5、6对该简支梁桥地震反应的减震效果相对最好,这与各种算法的阻尼器耗能大小有关。 相似文献
6.
7.
城市桥梁地震碰撞反应研究与发展 总被引：8，自引：5，他引：8
地震时城市桥梁会因邻跨之间的碰撞而发生灾害.本文从桥梁碰撞的模拟模型、发生条件、影响因素、碰撞对桥梁抗震性能的影响以及防止碰撞的措施等方面,对国内外有关城市桥梁碰撞地震反应研究的成果进行了系统的总结和分析,得出以下结论：桥梁碰撞是多因素共同作用所导致的,并使得桥梁的地震反应更加复杂、呈现非线性;要准确评价桥梁地震碰撞反应需要建立更精确的模拟模型;选择合理的邻跨间距和支座宽度以及安装合适的消能减震装置,可有效地减小桥梁的地震碰撞反应. 相似文献
8.
地震对多跨简支梁桥上列车运行安全的影响 总被引：3，自引：1，他引：3
主要讨论了地震对多跨简支梁桥上列车运行安全的影响，建立了综合考虑地震输入，轨道不平顺和车辆蛇行运动的车－桥体系振动的动力分析模型，通过输入典型地震波，模拟列车过桥全过程，计算了车辆与桥梁的动力响应，研究了地震荷载对秦沈客运专线跨度为1232m的简支T梁和简支箱梁列车运行安全的影响，并讨论了列车运行速度和桥梁下部基础条件与车桥动力响应的关系。 相似文献
9.
地震作用下隔震简支梁桥碰撞反应的振动台试验 总被引：2，自引：0，他引：2
由地震引发的碰撞是影响桥梁地震反应以及造成桥梁破坏的重要因素。本文对地震作用下隔震简支梁桥的碰撞反应进行了振动台试验。设计制作1个两跨简支的隔震梁桥模型,试验研究了梁间隙、邻梁质量比、隔震支座类型等参数对桥梁碰撞反应的影响。试验结果表明邻梁间隙、邻梁质量比、隔震支座类型等参数对桥梁的碰撞反应有着显著的影响。邻梁间隙越大,碰撞次数越少;邻梁质量比越大,撞击力越大。铅芯橡胶支座比板式橡胶支座耗能能力更强,可以有效降低邻梁之间的撞击力甚至避免碰撞发生。从而为桥梁防碰撞设计提供了可靠的试验依据。 相似文献
10.
《地震工程与工程振动》2016,(1)
地震造成的桥梁上部结构碰撞及落梁破坏在历次大地震中基本都能观察到,以往的研究大多数局限于地震作用下桥梁碰撞响应的数值模拟研究,相关的试验研究还不多。此外,这些研究中也少有考虑空间多维多点地震动作用引起的桥梁上部结构更大的异向振动。本文采用振动台台阵系统,对空间多维多点地震作用下相邻桥梁结构碰撞响应进行试验研究。试验设计制作了几何缩尺比为1∶6的桥梁模型,研究比较了空间多点激励以及摇摆基础与固定基础两种基础形式对试验模型地震碰撞响应的影响。介绍了试验模型的设计制作、传感器布置,给出了试验结果及模型桥梁碰撞破坏情况。试验结果表明,地震动的空间变异性不能忽视,较大的碰撞力会引起桥梁伸缩缝处混凝土严重的局部破坏,相比于固定基础,摇摆基础能有效降低墩的破坏程度,但提高了上部结构的碰撞及落梁风险。 相似文献
11.
12.
2021年5月22日青海玛多发生了Ms7.4级地震,从地震中桥梁震害情况看:此次地震的特点是断层北侧震害轻,南侧震害重。位于断层南侧的野马滩大桥是简支梁桥,发生大量落梁,是此次地震中受损最为严重的大桥之一;而位于北侧的大野马岭大桥是连续梁桥,仅发生了部分挡块开裂。其中原因值得深入研究。本文通过有限元分析软件Midas/Civil建立大野马岭大桥（上行线）模型,进行地震反应分析,讨论分析了大野马岭大桥在此次地震中的震害机理。发现南北向的地震动是造成该桥横向挡块破坏的主要原因,东西向地震动因受到桥台和纵向挡块的约束并没有出现严重损伤。若将该桥由连续梁桥变成简支梁桥,地震反应会有所变化,但总体趋势特点变化并不大。另外,本文通过现有资料选定5组地震动作为输入,进行地震反应分析,比较分析不同地震动对该桥的影响,并验证地震动模拟效果。 相似文献
13.
Seismic pounding between adjacent frames in multiple-frame bridges and girder ends in multi-span simply supported bridges has been commonly observed in several recent earthquakes. The consequences of pounding include damage to piers, abutments, shear keys, bearings and restrainers, and possible collapse of deck spans. This paper investigates pounding in bridges from an analytical perspective. A simplified nonlinear model of a multiple-frame bridge is developed including the effects of inelastic frame action and nonlinear hinge behavior, to study the seismic response to longitudinal ground motion. Pounding is implemented using the contact force-based Kelvin model, as well as the momentum-based stereomechanical approach, Parameter studies are conducted to determine the effects of frame period ratio, column hysteretic behavior, energy dissipation during impact and near source ground motions on the pounding response of the bridge. The results indicate that pounding is most critical for highly out-of-phase frames and is not significant for frame period ratios greater than 0.7. Impact models without energy dissipation overestimate the displacement and acceleration amplifications due to impact, especially for elastic behavior of the frames. Representation of stiffness degradation in bridge columns is essential in capturing the accurate response of pounding frames subjected to far field ground motion. Finally, it is shown that strength degradation and pounding can result in significant damage to the stiffer frames of the bridge when subjected to large acceleration pulses from near field ground motion records. 相似文献
14.
Implications of seismic pounding on the longitudinal response of multi-span bridges - an analytical perspective 总被引：2，自引：0，他引：2
ReginaldDesRoches SusendarMuthukumar 《地震工程与工程振动(英文版)》2004,3(1):57-65
Seismic pounding between adjacent frames in multiple-frame bridges and girder ends in multi-span simply supported bridges has been commonly observed in several recent earthquakes. The consequences of pounding include damage to piers, abutments, shear keys, bearings and restrainers, and possible collapse of deck spans. This paper investigates pounding in bridges from an analytical perspective. A simplified nonlinear model of a multiple-frame bridge is developed including the effects of inelastic frame action and nonlinear hinge behavior, to study the seismic response to longitudinal ground motion. Pounding is implemented using the contact force-based Kelvin model, as well as the momentum-based stereomechanical approach. Parameter studies are conducted to determine the effects of frame period ratio, column hysteretic behavior, energy dissipation during impact and near source ground motions on the pounding response of the bridge. The results indicate that pounding is most critical for highly out-of-phase frames and is not significant for frame period ratios greater than 0.7. Impact models without energy dissipation overestimate the displacement and acceleration amplifications due to impact, especially for elastic behavior of the frames. Representation of stiffness degradation in bridge columns is cssential in capturing the accurate response of pounding frames subjected to far field ground motion. Finally, it is shown that strength degradation and pounding can result in significant damage to the stiffer frames of the bridge when subjected to large acceleration pulses from near field ground motion records. 相似文献
15.
汶川大地震简支梁桥落梁震害与设计对策 总被引：2，自引：0，他引：2
总结了5.12汶川大地震中简支梁桥落梁震害及主要影响因素,发现除地震山体滑坡等地质灾害外,断层地表破裂、近断层地震动效应、桥台胸墙冲切破坏、防落梁构造措施单一及桥梁体型复杂等因素都是引起简支梁桥落梁震害的重要原因。提出了简支梁桥防落梁设计的基本理念及相关技术方案要点为允许墩梁间发生滑移,以降低桥墩承受的地震惯性力,以及盖梁提供允许的最大滑移长度及支座支承宽度,再辅助挡块或拉索限位器等共同防止落梁发生。最后结合现行规范,以拉索限位器为例给出了简支梁桥防落梁设计方法。 相似文献
16.
In the AASHTO Guide Specifications for Seismic Bridge Design Provisions,ductile diaphragms are identified as Permissible Earthquake-Resisting Elements(EREs),designed to help resist seismic loads applied in the transverse direction of bridges.When adding longitudinal ductile diaphragms,a bidirectional ductile diaphragm system is created that can address seismic excitations acting along both the bridge’s longitudinal and transverse axes.This paper investigates bidirectional ductile diaphragms with Buckling Restrained Braces(BRBs)in straight multi-span bridge with simply supported floating spans.The flexibility of the substructures in the transverse and longitudinal direction of the bridge is considered.Design procedures for the bidirectional ductile diaphragms are first proposed.An analytical model of the example bridge with bidirectional ductile diaphragms,designed based on the proposed methodology,is then built in SAP2000.Pushover and nonlinear time history analyses are performed on the bridge model,and corresponding results are presented.The effect of changing the longitudinal stiffness of the bidirectional ductile diaphragms in the end spans connecting to the abutment is also investigated,in order to better understand the impact on the bridge’s dynamic performance. 相似文献
17.
This study focuses on understanding and evaluating the effect of vehicle bridge interaction (VBI) on the response and fragility of bridges subjected to earthquakes. A comprehensive study on the effect of VBI on bridge seismic performance is conducted, providing metamodels for seismic response and fragility estimates for bridges in the presence of various types of vehicles. For this purpose, the performance of multispan simply supported concrete girder bridges with varying design and geometric parameters is assessed with 3 different types of stationary trucks placed atop them. To delineate the effects of VBI and additional truck mass, the trucks are modeled in 2 different ways—with additional masses and suspension springs (ie, with VBI) and using additional masses only (without VBI). The results provide insight on VBI effects, such as the fact that when bridge and vehicle mode shapes are in‐phase, the component responses increase and vice versa; additionally, the presence of a heavy axle near a bent increases component responses. Sensitivity analyses are also performed to determine the bridge parameters that significantly alter the component responses in the presence of vehicles. Furthermore, differences in component responses and fragilities highlight that modeling vehicles with additional masses alone is not sufficient to model the effect of truck presence on the seismic response of bridges. Finally, this study concludes that depending on the characteristics of the bridge and the vehicle, presence of a vehicle atop the bridge during an earthquake may be either beneficial or detrimental to bridge performance. 相似文献
18.
地震激励对高速车辆-简支箱梁桥系统动力响应的影响关系到高速铁路运营安全。基于车辆-轨道耦合动力学和列车-轨道-桥梁动力相互作用理论,运用有限元和多体动力学方法,建立高速铁路桥梁区段车辆-轨道-桥梁耦合系统动力学模型,分析在人工地震波作用下高速铁路车-线-桥耦合系统动力响应。结果表明:地震激励对轨道板、支撑层和桥梁的横向振动特性的影响大于对垂向振动特性的影响,桥梁结构对地震激励的敏感程度大于轨道结构;车辆运行速度对系统垂向振动特性的影响大于对横向振动特性的影响。研究结论可为地震荷载作用下高速铁路安全运营提供理论依据。 相似文献