共查询到20条相似文献，搜索用时 109 毫秒
1.
2.
大陆上用重力数据和GPS水准数据确定(似)大地水准面,海洋上用卫星测高数据确定(似)大地水准面.由于沿海地区和近岸海域往往缺少完好的重力数据,近岸海域卫星测高数据质量相对较差,两类大地水准面在陆海相接区域精度偏低且存在拼合差.纯几何方法拟合陆海局部区域大地水准面,不能顾及大地水准面的物理特性,拟合结果不稳定.顾及到大地水准面的物理特性,依据其在局部所应满足的数学物理方程,拟合陆海局部区域大地水准面问题,转化为Laplace第一边值问题.讨论了有限元法衔接陆海局部区域大地水准面的数学思想,给出了相应的数学模型. 相似文献
3.
随着GPS/水准及全球重力测量的加密和扩展,获取高精度的似大地水准面或高程异常(ξ)已比较容易,如何进一步研究它和大地水准面或大地水准面高(N)之间的关系(即所谓间接的方法)使大地水准面得到精化,这就是本文的目的,文中对已推导的公式在模型作了验证,对如何利用地形等数据确定扰动重力垂直梯度也作了研究,结果表明:在海拔4000 m的高山地区,当似大地水准面的精度达到cm级时,大地水准面的精度也与之比较接近. 相似文献
4.
针对构建似大地水准面中采用的重力水准法、EGM2008水准法、GPS水准法,结合地形复杂程度、面积大小、重力似大地水准面分辨率与精度等特点,首次评价了基于多种方法构建的似大地水准面模型的外推性与真实性.采用地形复杂区域S、平原区域N以及沿海区域Q构建区域似大地水准面模型.通过时各方法得到的似大地水准面模型推估特性分析比较,结果表明:就反应似大地水准面起伏的真实情况而言,重力水准法精度最高且外推能力最强;EGM2008水准法精度次之,外推能力较强外推范围在10 km左右;GPS水准法精度最弱,外推能力最差.构建高精度高分率1 cm级似大地水准面时须采用基于grave/level法. 相似文献
5.
局部似大地水准面精化中需要进行GPS水准与重力两种水准面的拟合,其中两种观测量精度的权比确定是关键问题,本文提出基于方差分量估计的方法解决这一问题.根据此思路,文中还利用某给定区域的实际资料,对常用的几种似大地水准面拟合方法——多项式拟合、多面函数拟合以及曲面样条插值的函数模型按不等权拟合似大地水准面进行试验.通过某3... 相似文献
6.
我国在海域开展了大规模的航空重力勘探,这些资料对构建高精度大地水准面具有重要价值.基于此,本文提出一种利用海域航空重力测量数据快速构建大地水准面的方法.该方法基于移去-恢复法思想,利用位场最小曲率方法对航空重力数据进行高精度向下延拓并获取相应的扰动位,实现航空重力测量快速构建海域大地水准面.与斯托克斯积分计算相比,采用了处理效率更高的频率域位场转换,解决了向下延拓及垂向积分时航空重力异常数据空白及扩边问题,具有较高的位场转换精度.本文应用EGM2008模拟航空重力数据进行模型验证,计算结果与其给出的水准面的精度相当;同时,也选取GRAV-D计划的航空重力数据进行实际验证,计算结果与xGEOID18B水准面模型精度基本一致.模型验证和实际应用验证了本方法的实用性. 相似文献
7.
融合多源数据的高精度、高分辨率的局部重力场建模是物理大地测量学的前沿和热点问题.本文研究了基于径向基函数融合多源数据的局部重力场建模方法,利用Monte-Carlo方差分量估计实现了不同类型的观测数据的合理定权,引入了最小标准差法确定基函数的适宜网络,分析了地形因素对于基函数网络确定及局部重力场建模精度的影响.以泊松小波基函数为构造基函数,结合残差地形模型,融合实测的陆地重力异常、船载重力异常及航空重力扰动数据构建了局部区域陆海统一的似大地水准面模型.研究结果表明:引入残差地形模型平滑了地形质量引入的高频扰动信号,简化了基函数的网络设计;并提高了重力似大地水准面的精度,平原地区其精度提高了4mm,地形起伏较大的山区其精度提高了约5cm.总体而言,基于"三步法"构建的局部重力似大地水准面在荷兰、比利时及德国相关区域,其精度分别达到1.12cm、2.80cm以及2.92cm. 相似文献
8.
9.
本文使用珠峰及其周边地区的重力数据与SRTM3、1∶50000 DEM、GTOPO30地形数据,以该地区的44个GPS水准点为控制,选择国内外的EGM96、WDM94、IGG05B、DQM2000D和CG03C作为参考重力场模型,采用移去-恢复技术,首次完成了珠峰地区分辨率为2.5′×2.5′高精度似大地水准面,其精度达到±9 cm,并据此推算了珠峰顶高程异常值. 再利用登山线路上的新测重力点与珠峰地形数据,依据严格的重力归算理论及移去-恢复技术,完成了珠峰顶似大地水准面与大地水准面差值计算,即珠峰正常高与正高的换算. 相似文献
10.
高精度高程基准重力位的确定往往依赖于高精度全球重力场模型,其对全球和区域高程基准的高精度统一非常关键,GRACE、GOCE卫星重力计划极大地提高了全球重力场模型中长波的精度.本文首先对GRACE/GOCE卫星重力场模型的内符合和外符合精度进行讨论分析,结果说明卫星重力模型的截断误差影响可达到分米级水平,在确定高程基准重力位时该影响不可忽略.利用EGM2008模型扩展GRACE/GOCE卫星重力场模型至2190阶,可有效减弱卫星重力模型的截断误差影响,但不同模型扩展时的最优拼接阶次不同,其中DIR-1、DIR-5模型对应的最优拼接阶次分别为180阶和220阶,以GPS水准数据检验,扩展模型在中国区域的精度均优于18cm.最后,基于最优拼接阶次获得的扩展重力场模型对我国1985高程基准重力位进行了估计,DIR-5和TIM-5模型对应数值分别为62636853.47m~2·s~(-2)和62636853.49m~2·s~(-2),精度均为1.51m~2·s~(-2);发现在中国区域模型大地水准面与GPS/水准数据的差值存在微弱的系统性倾斜,东西向倾斜约为9cm,南北向倾斜约为1.4cm,考虑倾斜改正后基于DIR-5和TIM-5模型估计我国1985高程基准重力位的精度提高了0.16m~2·s~(-2). 相似文献
11.
Comparison of the qualities of recent global and local gravimetric geoid models in Iran 总被引：1，自引：0，他引：1
A number of regional gravimetric geoid models have recently been determined for the Iran area, and a common problem is to select the best model, e.g. for engineering applications. A related problem is that in order to improve the local geoid models, the selection of the best Global Geopotential Model (GGM) model for the region is essential, to be used in a combined solution from GGM and local gravimetric data. We discuss these problems by taking advantage of 260 GPS/levelling points as an external tool for validation of different global and local geoid models in the absolute and relative senses. By using relative comparisons of the height differences between precise levelling and GPS/geoid models we avoid possible unknown systematic effects between the different types of observables.The study shows that the combination of the newly released GRACE model (GGM02C) with EGM96 geoid model fits the GPS/levelling data in Iran with the best absolute and relative accuracy among the GGMs. Among the local geoid models, the newly gravimetric geoid model IRG04 agrees considerably better with GPS/levelling than any of the other recent local geoid models. Its rms fit with GPS/levelling is 55 cm. Hence, we strongly recommend the use of this new model in any surveying engineering or GPS/levelling projects in the area. 相似文献
12.
From the late 1990s, many studies on local geoid construction have been made in South Korea. However, the precision of the previous geoid has remained about 15 cm due to distribution and quality problems of gravity and GPS/levelling data. Since 2007, new land gravity data and GPS/levelling data have been obtained through many projects such as the Korean Land Spatilaization, Unified Control Point and Gravity survey on the Benchmark. The newly obtained data are regularly distributed to a certain degree and show much better improvement in their quality. In addition, an airborne gravity survey was conducted in 2008 to cover the Korean peninsula (South Korea only). Therefore, it is expected that the precision of the geoid could be improved. In this study, the new South Korean gravimetric geoid and hybrid geoid are presented based on land, airborne, ship‐borne, altimeter gravity data, geopotential model and topographic data. As for the methodology, the general remove‐restore approach was applied with the best chosen parameters in order to produce a precise local geoid. The global geopotential model EGM08 was used to remove the low‐frequency components using degree and order up to 360 and the short wavelength part of the gravity signal was dealt with by using the Shuttle Radar Topography Mission data. The parameters determined empirically in this study include for Stokes’ integral 0.5° and for Wong‐Gore kernel 110–120°, respectively and 10 km for both the Bjerhammar sphere depth and attenuation factor. The final gravimetric geoid in South Korea ranges from 20–31 m with a precision of 5.45 cm overall compared to 1096 GPS/levelling data. In addition, the South Korean hybrid geoid produces 3.46 cm and 3.92 cm for degrees of fitness and precision, respectively and a better statistic of 2.37 cm for plain and urban areas was achieved. The gravimetric and hybrid geoids are expected to improve further when the refined land gravity data are included in the near future. 相似文献
13.
Contributions of terrestrial and GRACE data to the study of the secular geoid changes in North America 总被引：1，自引：0，他引：1
This paper tests and discusses different statistical methods for modelling secular rates of change of the geoid in North America. In particular, we use the method of principal component/empirical orthogonal functions (PC/EOF) analysis to model the geoid rates from Gravity Recovery and Climate Experiment (GRACE) satellite data. As demonstrated, the PC/EOF analysis is useful for studying the contributions from different signals (mainly residual hydrology signals and leakage effects) to the GRACE-derived geoid rates. The PC/EOF analysis leads to smaller geoid rates compared to the conventional least-squares fitting of a trend and annual and semi-annual cycles to the time series of the spherical harmonic coefficients. This is because we filter out particular spatiotemporal modes of the regional geoid changes.We apply the method of least-squares collocation with parameters to combine terrestrial data (GPS vertical velocities from the Canadian Base Network and terrestrial gravity rates from the Canadian Gravity Standardization Net) with the GRACE-derived vertical motion to obtain again the geoid rates. The combined model has a peak geoid rate of 1.4 mm/year in the southeastern area of Hudson Bay contrary to the GRACE-derived geoid rates that show a large peak of 1.6–1.7 mm/year west of Hudson Bay. We demonstrate that the terrestrial data, which have a longer time span than the GRACE data, are important for constraining the GRACE-derived secular signal in the areas that are well sampled by the data. 相似文献
14.
This paper deals with a method for detection of local geoid deformations; as a consequence, the methods main application concerns geoid adjustment to GPS/levelling points. This is based on the fact that these points should present no local geoid deformation to avoid errors in the adjustments. These type of miscalculations would lead to an incorrect adjustment and result in further errors in subsequent studies with GPS in the proximity at the point with local deformation.The method proposed is based on predictions of gravity disturbance from geoid undulations using Poisson integral with modified kernel, and its comparison with the gravity disturbance from GPS and gravimetric observations.The use of gravity disturbance instead of gravity anomalies has been chosen since gravity disturbance is a quantity derived from GPS and not from levelling. The loss of accuracy arising with a local height reference system is therefore theoretically avoided as far as the differences in geodetic reference systems regarding positions of gravity measurements and coefficients of the global models are accounted for.Extended numerical tests using computed geoidal undulations and the corresponding gravity disturbances obtained from the geopotential model GPM98cr computed up to degree 720 illustrate the validity of the proposed method and its usefulness as local geoid deformations detection tool.Finally, the method is tested using real GPS/Gravimetric data and geoid models IBERGEO95 and EGG97 with good results. 相似文献
15.
The continuous efforts on establishment and modernization of the geodetic control in Turkey include a number of regional geoid
models that have been determined since 1976. The recently released gravimetric Geoid of Turkey, TG03, is used in geodetic
applications where GPS-heights need to be converted to the local vertical datum. To reach a regional geoid model with improved
accuracy, the selection of the appropriate global geopotential model is of primary importance. This study assesses the performance
of a number of recent satellite-only and combined global geopotential models (GGMs) derived from CHAMP and GRACE missions’
data in comparison to the older EGM96 model, which is the underlying reference model for TG03. In this respect, gravity anomalies
and geoid heights from the global geopotential models were compared with terrestrial gravity data and low-pass filtered GPS/levelling
data, respectively. Also, five new gravimetric geoid models, computed by the Fast Fourier Transform technique using terrestrial
gravity data and the geopotential models, were validated at the GPS/levelling benchmarks. The findings were also compared
with the validation results of the TG03 model.
The tests showed that as it was expected any of the high-degree combined models (EIGEN-CG03C, EIGEN-GL04C, EGM96) can be employed
for determining the gravity anomalies over Turkey. In the west of Turkey, EGM96 and EIGEN-CHAMP03S fit the GPS/levelling surface
better. However, all the tested GGMs revealed equal performance when they were employed in gravimetric geoid modelling after
de-trending the gravimetric geoid model with corrector surface fitting. The new geoid models have improved accuracy (after
fit) compared to TG03. 相似文献
16.
A precise gravimetric geoid model in a mountainous area with scarce gravity data: a case study in central Turkey 总被引：1，自引：0，他引：1
Ramazan A. Abbak Lars E. Sj?berg Artu Ellmann Aydin Ustun 《Studia Geophysica et Geodaetica》2012,56(4):909-927
In mountainous regions with scarce gravity data, gravimetric geoid determination is a difficult task that needs special attention to obtain reliable results satisfying the demands, e.g., of engineering applications. The present study investigates a procedure for combining a suitable global geopotential model and available terrestrial data in order to obtain a precise regional geoid model for Konya Closed Basin (KCB). The KCB is located in the central part of Turkey, where a very limited amount of terrestrial gravity data is available. Various data sources, such as the Turkish digital elevation model with 3 ?? × 3?? resolution, a recently published satellite-only global geopotential model from the Gravity Recovery and Climate Experiment satellite (GRACE) and the ground gravity observations, are combined in the least-squares sense by the modified Stokes?? formula. The new gravimetric geoid model is compared with Global Positioning System (GPS)/levelling at the control points, resulting in the Root Mean Square Error (RMS) differences of ±6.4 cm and 1.7 ppm in the absolute and relative senses, respectively. This regional geoid model appears to be more accurate than the Earth Gravitational Model 2008, which is the best global model over the target area, with the RMS differences of ±8.6 cm and 1.8 ppm in the absolute and relative senses, respectively. These results show that the accuracy of a regional gravimetric model can be augmented by the combination of a global geopotential model and local terrestrial data in mountainous areas even though the quality and resolution of the primary terrestrial data are not satisfactory to the geoid modelling procedure. 相似文献
17.
Modelling the fine-structure of the geoid: Methods,data requirements and some results 总被引：2，自引：0，他引：2
Rene Forsberg 《Surveys in Geophysics》1993,14(4-5):403-418
The requirements for precise geoid models on local and regional scales have increased in recent years, primarily due to the ongoing developments in height determination by GPS on land, but also due to oceanographic requirements in using satellite altimetry for recovering dynamic sea-surface topography. Suitable methods for geoid computations from gravity data include Stokes integration, FFT methods, and least-squares collocation. Especially the FFT methods are efficient in handling large amounts of gravity data, and new variants of the methods taking earth curvature rigorously into account provide attractive methods for obtaining continental-scale, high-resolution geoid models. The accuracy of such models may be from 2–5 cm locally, to 50–100 cm on regional scales, depending on gravity data coverage, long wave-length gravity field errors, and datum problems. When approaching the cm-level geoid basic geoid definition questions (geoid or quasigeoid?) become very significant, especially in rugged areas. In the paper the geoid modelling methods and problems are reviewed, and some investigations on local data requirements for cm-level geoid prediction are presented. Some actual results are presented from Scandinavia, where a recent regional high-resolution geoid model yields apparent accuracies of 2–10 cm over GPS baselines of 50 to 2000 km. 相似文献
18.
本文首次利用解析法有效快速估计了将来GRACE（Gravity Recovery and Climate Experiment） Follow-On地球重力场的精度. 第一,基于功率谱原理分别建立了新的GRACE Follow-On卫星激光干涉星间测量系统星间速度、GPS接收机轨道位置和轨道速度以及加速度计非保守力误差影响累计大地水准面的单独和联合解析误差模型. 第二,利用提出的GRACE卫星关键载荷匹配精度指标和美国喷气推进实验室（JPL）公布的GRACE Level 1B实测精度指标的一致性,以及估计的GRACE累计大地水准面精度和德国波兹坦地学研究中心（GFZ）公布的EIGEN-GRACE02S地球重力场模型实测精度的符合性,验证了本文建立的解析误差模型是可靠的. 第三,论证了GRACE Follow-On卫星不同关键载荷匹配精度指标和轨道高度对地球重力场精度的影响. 在360阶处,利用轨道高度250 km、星间距离50 km、星间速度误差1×10-9m/s、轨道位置误差3×10-5m、轨道速度误差3×10-8m/s和非保守力误差3×10-13m/s2,基于联合解析误差模型估计累计大地水准面的精度为1.231×10-1 m. 本文的研究不仅为当前GRACE和将来GRACE Follow-On地球重力场精度的有效快速确定提供了理论基础和计算保证,同时对国际将来GRAIL（Gravity Recovery and Interior Laboratory）月球卫星重力测量计划的成功实施具有重要的参考意义. 相似文献
19.
Blázquez E.B. Gil A.J. Rodríguez-Caderot G. de Lacy M.C. Ruiz J.J. 《Studia Geophysica et Geodaetica》2003,47(3):511-520
In 1991 the first determination of a gravimetric geoid in a test area in central Spain was computed by using least square collocation. In 1995 a gravimetric geoid in the Iberian Peninsula, Ibergeo95, was calculated by FFT. Nowadays an improved geoid of Andalusia, ANDALUSGeoid2002, has been computed by fast collocation procedure and remove-restore technique in the GRS80 Reference System. The computations have been done from 16562 free-air gravity anomaly data set, obtained from IGN (Instituto Geográfico Nacional) and BGI (International Gravity Bureau), the Earth Gravity Model EGM96 and detailed (100 m × 100 m), coarse (5 km × 5 km) and reference (20 km × 20 km) digital terrain models. Relative carrier-phase GPS measurements at 69 benchmarks of the Spanish Levelling Network in Andalusia have been done. The standard deviations of differences between ANDALUSGeoid2002 and GPS/levelling undulations after fitting the tilt have been ± 11 cm, ± 39 cm and ± 38 cm in western, eastern and whole Andalusia, respectively. The ANDALUSGeoid2002 shows an improvement of Ibergeo95 in this territory. 相似文献
20.
Transformation between gravimetric and GPS/levelling-derived geoids using additional gravity information 总被引：1，自引：0，他引：1
The transformation from the gravimetric to the GPS/levelling-derived geoid using additional gravity information for the covariance function of geoid height differences has been investigated in a test area in south-western Canada. A “corrector surface” model, which accounts for datum inconsistencies, long-wavelength geoid errors, vertical network distortions and GPS errors, has been constructed using least-squares collocation. The local covariance function of geoid height differences is usually obtained from residual values between the GPS/levelling and gravimetric geoid heights after the elimination of all known systematic distortions. If additional gravity data (in the form of gravity anomalies) are available, the covariance function of geoid height differences can be determined by the following steps: (1) transforming the GPS/levelling-derived geoid heights into gravity anomalies; (2) forming differences between the computed in step 1 and given gravity anomalies; (3) determining the parameters of the local covariance function of the gravity anomaly differences; (4) constructing an analytical covariance model for the geoid height differences from the covariance function of the gravity anomaly differences using the parameters derived in step 3. The advantage of the proposed method stems from the great number of gravity data used to derive the empirical covariance function. A comparison with the least-squares adjustment shows that the standard deviation of the residuals of the predicted geoid height differences with respect to the control point values decreases by 2.4 cm. 相似文献