共查询到20条相似文献，搜索用时 125 毫秒
1.
E. Tubaldi S. A. Mitoulis H. Ahmadi A. Muhr 《Bulletin of Earthquake Engineering》2016,14(4):1285-1310
This paper investigates the potential tensile loads and buckling effects on rubber-steel laminated bearings on bridges. These isolation bearings are typically used to support the deck on the piers and the abutments and reduce the effects of seismic loads and thermal effects on bridges. When positive means of fixing of the bearings to the deck and substructures are provided using bolts, the isolators are exposed to the possibility of tensile loads that may not meet the code limits. The uplift potential is increased when the bearings are placed eccentrically with respect to the pier axis such as in multi-span simply supported bridge decks. This particular isolator configuration may also result in excessive compressive loads, leading to bearing buckling or in the attainment of other unfavourable limit states for the bearings. In this paper, an extended computer-aided study is conducted on typical isolated bridge systems with multi-span simply-supported deck spans, showing that elastomeric bearings might undergo tensile stresses or exhibit buckling effects under certain design situations. It is shown that these unfavourable conditions can be avoided with the rational design of the bearing properties and in particular of the shape factor, which is the geometrical parameter controlling the axial bearing stiffness and capacity for a given shear stiffness. Alternatively, the unfavourable conditions could be reduced by reducing the flexural stiffness of the continuity slab. 相似文献
2.
为充分了解板式橡胶支座对斜交连续梁桥地震反应的影响,利用OpenSees软件建立简化的斜交桥计算模型进行时程分析,研究板式橡胶支座摩擦滑移效应,以及支座动摩擦系数、剪切刚度、局部脱空等参数对斜交桥地震反应的影响。结果表明:板式橡胶支座考虑摩擦滑移后,不仅桥面位移和转角显著增大,而且出现残余位移和残余转角;随着支座剪切刚度的增大,桥面位移和转角均明显减小;随着桥墩处支座动摩擦系数的增大,桥面位移、转角均呈增长趋势,然而桥台处支座动摩擦系数的影响与之相反;桥墩处局部支座脱空对斜交桥的影响明显大于桥台支座。 相似文献
3.
Seismic analysis of a curved bridge considering deck‐abutment pounding interaction: an analytical investigation on the post‐impact response 
下载免费PDF全文
下载免费PDF全文 Horizontal curved bridges are very common at intersections and at the changing angle of bridge alignment. Almost in every previous earthquake report, it can be seen that the columns of a curved segment experience torsional damage, and the curved decks are unseated from the abutment support. The main reason behind that phenomenon is the in‐plane deck rotation which results because of the complex dynamic coupling between two longitudinal directional vibrations. The curved decks are susceptible to deck rotation because in a curved segment, the centre of mass and the centre of stiffness generally lie outside the bridge deck and are not located at the same point. The pounding with the abutment often increases the rotational tendency of the deck. In this paper, a classical mechanics‐based approach is adopted to analytically estimate the deck rotation potential of curved bridge considering the deck‐abutment pounding interaction. The deck‐abutment pounding is modelled using non‐smooth techniques considering the Newton's impact law in the normal and Coulomb's friction in the tangential direction. Within the scope of this paper, a parametric study is performed to get the ideal combination of the column and bent arrangement and the gap distance. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
4.
The modern transportation facilities demand that the bridges are to be constructed across the gorges that are located in seismically active areas and at the same time the site conditions compel the engineers to rest the pier foundation on soil. The purpose of this study is to assess the effects of soil–structure interaction (SSI) on the peak responses of three-span continuous deck bridge seismically isolated by the elastomeric bearings. The emphasis has been placed on gauging the significance of physical parameters that affect the response of the system and identify the circumstances under which it is necessary to include the SSI effects in the design of seismically isolated bridges. The soil surrounding the foundation of pier is modelled by frequency independent coefficients and the complete dynamic analysis is carried out in time domain using complex modal analysis method. In order to quantify the effects of SSI, the peak responses of isolated and non-isolated bridge (i.e. bridge without isolation device) are compared with the corresponding bridge ignoring these effects. A parametric study is also conducted to investigate the effects of soil flexibility and bearing parameters (such as stiffness and damping) on the response of isolated bridge system. It is observed that the soil surrounding the pier has significant effects on the response of the isolated bridges and under certain circumstances the bearing displacements at abutment locations may be underestimated if the SSI effects are not considered in the response analysis of the system. 相似文献
5.
为了合理计算山区桥梁支座刚度,针对桥墩高度不相同的特点,考虑上部结构对桥墩顶部的转动约束作用,提出在横桥向可将墩顶视为自由约束,而在纵桥向将墩顶视为定向约束。分别按照地震作用下各墩底剪力和弯矩相等的原则,推导桥梁支座纵、横桥向的刚度设计公式,并给出各桥墩支座的设计方法。为验证方法的正确性,以墩底剪力相等的原则为例,利用OpenSees建立一座墩高不等的5跨连续梁桥模型,并依支座刚度取值不同分三种工况:工况一各桥墩支座刚度相同;工况二按墩顶自由计算各支座的纵、横桥向刚度;工况三按墩顶定向约束计算各支座的纵、横桥向刚度。分别对三种工况下的桥梁结构输入三条地震动记录进行时程分析,考察各桥墩的底部剪力。分析结果表明:工况一各桥墩纵、横桥向的底部剪力均不相同;工况二各桥墩横桥向的底部剪力相同而纵桥向的底部剪力不同;工况三各桥墩纵桥向的底部剪力相同而横桥向的底部剪力不同。上述结果表明在桥梁支座设计时,横桥向桥墩的抗推刚度应按墩顶自由计算,而纵桥向桥墩的抗推刚度应按墩顶为定向约束计算。 相似文献
6.
Design formulas for supplemental viscous dampers to building structures are readily available in FEMA provisions and MCEER research reports. However, for the design of supplemental viscous dampers corresponding to a desired system damping ratio of highway bridges, there exist, if any, few design guidelines. This is particularly true if the bridge components such as elastomeric bearings, piers and abutment possess different damping ratios, stiffnesses, and lumped masses. In this paper, the design formulas for supplemental viscous dampers to highway bridges have been derived based on the concept of ‘composite damping ratio’. The design formulas can be used to determine the damping coefficients of the dampers corresponding to a desired system damping ratio of the bridge in which different component damping ratios may be assumed for the elastomeric bearings, piers and abutments. The proposed design formulas are numerically validated by comparing the seismic responses of a three‐span bridge equipped with viscous dampers with those of the same bridge without viscous dampers but with an assigned inherent system damping ratio equal to the target system damping ratio. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
7.
Nonsmooth dynamics prediction of measured bridge response involving deck‐abutment pounding 下载免费PDF全文
下载免费PDF全文 Earthquake‐induced deck‐abutment contact alters the boundary conditions at the deck level and might activate a different mechanical system than the one assumed during the design of the bridge. Occasionally this discrepancy between the assumed and the actual seismic behavior has detrimental consequences, for example, pier damage, deck unseating, or even collapse. Recently, an insightful shake‐table testing of a scaled deck‐abutment bridge model 1 , showed unexpected in‐plane rotations even though the deck was straight. These contact‐induced rotations produced significant residual displacements and damage to the piers and the bents. The present paper utilizes that experimental data to examine the validity and the limitations of a proposed nonsmooth dynamic analysis framework. The results show that the proposed approach satisfactorily captures the planar rigid‐body dynamics of the deck which is characterized by deck‐abutment contact. The analysis brings forward the role of friction on the physical mechanism behind the rotation of the deck, and underlines the importance of considering the frictional contact forces during deck‐abutment interaction even for straight bridges, which typically are neglected. Finally, the paper investigates the sensitivity of the rotation with respect to macroscopic contact parameters (i.e., the coefficient of friction and the coefficient of restitution). Copyright © 2017 John Wiley & Sons, Ltd. 相似文献
8.
Extending the application of integral frame abutment bridges in earthquake‐prone areas by using novel isolators of recycled materials 下载免费PDF全文
下载免费PDF全文 Stergios A. Mitoulis Anastasia Palaiochorinou Ilias Georgiadis Sotiris Argyroudis 《地震工程与结构动力学》2016,45(14):2283-2301
Integral abutment bridges (IABs) are jointless structures without bearings or expansion joints which require minimum or zero maintenance. The barrier to the application of long‐span integral abutment bridges is the interaction of the abutment with the backfill soil during the thermal expansion and contraction of the bridge deck, that is, serviceability, or when the bridge is subjected to dynamic loads, such as earthquakes. The interaction of the bridge with the backfill leads to settlements and ratcheting of the soil behind the abutment and, as a result, the soil pressures acting on the abutment build up in the long term. This paper provides a solution for the aforementioned challenges by introducing a novel isolator that is a compressible inclusion of reused tyre‐derived aggregates placed between the bridge abutment and the backfill. The compressibility of typical tyre‐derived aggregates was measured by laboratory tests, and the compressible inclusion was designed accordingly. The compressible inclusion was then applied to a typical integral frame abutment model, which was subjected to static and dynamic loads representing in‐service and seismic loads correspondingly. The response of both the conventional and the isolated abutment was assessed based on the settlements of the backfill, the soil pressures and the actions of the abutment. The study of the isolated abutment showed that the achieved decoupling of the abutment from the backfill soil results in significant reductions of the settlements of the backfill and of the pressures acting on the abutment. Hence, the proposed research enables extending the length limits of integral frame bridges subjected to earthquake excitations. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
9.
This paper examines the eigenvalues of multi‐span seismically isolated bridges in which the transverse displacement of the deck at the end abutments is restricted. With this constraint the deck is fully isolated along the longitudinal direction, whereas along the transverse direction the deck is a simple‐supported beam at the end abutments which enjoys concentrated restoring forces from the isolation bearings at the center piers. For moderate long bridges, the first natural period of the bridge is the first longitudinal period, while the first transverse period is the second period, given that the flexural rigidity of the deck along the transverse direction shortens the isolation period offered by the bearings in that direction. This paper shows that for isolated bridges longer than a certain critical length, the first transverse period becomes longer than the first longitudinal period despite the presence of the flexural rigidity of the deck. This critical length depends on whether the bridge is isolated on elastomeric bearings or on spherical sliding bearings. This result is also predicted with established commercially available numerical codes only when several additional nodes are added along the beam elements which are modeling the deck in‐between the bridge piers. On the other hand, this result cannot be captured with the limiting idealization of a beam on continuous distributed springs (beam on Wrinkler foundation)—a finding that has practical significance in design and system identification studies. Finally, the paper shows that the normalized transverse eigenperiods of any finite‐span deck are self‐similar solutions that can be represented by a single master curve and are independent of the longitudinal isolation period or on whether the deck is supported on elastomeric or spherical sliding bearings. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
10.
不同约束方式对匝道桥动力特性的影响研究 总被引：1，自引：0，他引：1
近年来,地震作用下的匝道桥表现出较高的地震易损性。为建立匝道桥的有效约束方式,以减小其地震损伤,本文基于汶川地震中连续梁桥约束方式的调研结果,建立了4种不同匝道桥支座约束方式,并以石家庄石环线某匝道桥为例,对比分析了不同约束方式下匝道桥的自振特性及地震响应。结果表明:板式橡胶支座具有一定的剪切变形能力,可降低桥墩与支座组成的体系刚度,有效分散了上部结构的地震惯性力,保护了下部结构,但应注意其引起的较大主梁位移;固定支座或墩梁固结形式会放大桥墩受力,增加下部结构的损坏,不宜设置在高度较矮、刚度较大的桥墩上;双层挡块和垫石凹槽分级限位支座具有较好的限位能力,并可耗散部分地震能量。 相似文献
11.
The aseismic design of cable-stayed bridges in the transverse direction with newly proposed metallic dampers that can accommodate both longitudinal and transverse movement of the deck has recently been considered. This work focuses on developing a simplified method to design an appropriate metallic damper. The seismic performance of cablestayed bridges with different damper stiffness, main span lengths, tower shapes and types of deck in the transverse direction are investigated. The transverse displacement of the deck of a cable-stayed bridge increases significantly with the increment of the damper stiffness, which proves that the design of the damper stiffness is crucial. A simplified model considering the damper stiffness, cable system and tower in the transverse direction is developed to evaluate the period and lateral displacement of a complicated cable-stayed bridge. Based on the simplified model, a design method is proposed and assessed using two cable-stayed bridges as examples. The results show that metallic dampers can be designed with high efficiency, and the optimal ductility of the damper can be selected. 相似文献
12.
针对平面不规则结构在水平地震作用下的振动特性,通过调整隔震层隔震支座的布置,得到3种不同工况的隔震层刚心与上部结构质心、刚心相对位置关系,分别以楼层位移和层间位移为指标的扭转位移比,作为平面不规则基础隔震结构扭转响应指标,利用弹塑性时程分析方法,通过对3种不同工况的扭转指标对比分析研究,提出适用于平面不规则基础隔震结构的抗扭设计方法。结果表明：对于平面不规则结构,应在保证隔震层扭转位移比小于1.2的基础上,使隔震层的刚心和上部结构的刚心分别位于上部结构质心的两侧,可有效控制上部结构的扭转。 相似文献
13.
14.
This study assesses analytically the effectiveness, feasibility and limitations of elastic and hysteretic damping augmentation devices, such as elastomeric and lead–rubber bearings, with respect to the dynamic and seismic performance of cable-stayed bridges. This type of bridge, which has relatively greater flexibility, is more susceptible to undesirable vibrations due to service and environmental loadings than are conventional bridges. Therefore, damping is a very important property. Supplementary damping devices based on the plastic deformation of lead and steel are proposed at critical zones, such as the deck–abutment and deck–tower connections, to concentrate hysteretic behaviour in these specially designed energy absorbers. Inelastic behaviour in primary structural elements of the bridge can therefore be avoided, assuring the serviceability of these cable-supported bridges. Analytically, three-dimensional modelling is developed for the bridge and the damping devices, including the bridge geometrical large-displacement non-linearity and the local material and geometric non-linearities of the energy dissipation devices. The effects of various modelling and design parameters of the bridge response are also studied, including the properties, modelling accuracy and location of the devices along the bridge superstructure. It is shown that an optimum model of the seismic performance of the bridges with these passive control devices can be obtained by balancing the reduction in forces along the bridge against tolerable displacements. Appropriate locations and hysteretic energy dissipation properties of the devices can achieve a significant reduction in seismic-induced forces, as compared to the case with no dampers added, and relatively better control of displacements. In addition, proper selection of the location of the passive control systems can help redistribute forces along the structure which may provide solutions for retrofitting some existing bridges. However, caution should be exercised in simulating the device response for a reliable bridge structural performance. Moreover, while seismic response of the bridge can be significantly improved with added dampers, their degree of effectiveness also depends on the energy absorption characteristics of the dampers. 相似文献
15.
Uplift of deck or footings in bridges with distributed mass subjected to transverse earthquake 下载免费PDF全文
下载免费PDF全文 Michael N. Fardis 《地震工程与结构动力学》2015,44(15):2755-2773
The eigenvalue problem is analytically formulated in symmetric bridges with distributed mass and moment of inertia under transverse earthquake. The piers are elastically supported on the ground. The deck is monolithically connected to one or two piers for all degrees of freedom and restrained or transversely free at the abutments. The characteristic equation, symmetric normal modes, modal participation factors, and participating mass ratios are given analytically. The problem is expressed in terms of few dimensionless parameters: (i) the radius of gyration of the deck mass divided by the pier height; (ii) the ratio of the rotational stiffness of a footing to that of the pier at the base; (iii) the ratio of flexural stiffness of the outer spans to those of the pier; (iv) the ratio of torsional stiffness of side spans to the rotational stiffness of the pier top; (v) for two piers, the side‐to‐central‐span ratio. Modal response spectrum analysis gives the moment at the base of the footings and the torque in the deck at its supports on the abutments as ratios to the values at incipient uplifting from the ground or the bearings. The peak ground acceleration of the motion at the onset of either one of these two types of nonlinearity is depicted as a function of the dimensionless parameters and the fundamental period of an elastic deck supported only at the abutments, or of a rigid deck on piers fixed against rotation at top and bottom. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
16.
A finite element model is constructed for a sliding friction bearing in a seismically isolated bridge under vertical excitation with contact/friction elements. The effects of vertical excitation on the seismic performance of a seismically isolated bridge with sliding friction bearings and different bearing friction coefficients and different stiffness levels (pier diameter) are discussed using example calculations, and the effects of excitation direction for vertical excitation on the analysis results are explored. The analysis results shows that vertical excitation has a relatively large impact on seismic performance for a seismically isolated bridge with sliding friction bearings, which should be considered when designing a seismically isolated bridge with sliding friction bearings where vertical excitation dominates. 相似文献
17.
本文以一座三跨总长60 m的整体桥为案例桥,分别试设计了同跨径的半整体桥、延伸桥面板桥和常规连续梁桥。通过Midas/Civil软件建立四种桥型的有限元模型,并对其进行了E1和E2反应谱分析和时程分析,对比了四种桥型的结构反应峰值（墩顶位移、桥墩及桩基剪力与弯矩、台底位移、桥台桩基剪力与弯矩）。计算结果表明:当桥梁存在15°的斜交角,整体桥、半整体桥在地震动沿平行于桥台长边方向及其垂直方向输入时更不利,而延伸桥面板桥和常规连续梁桥在地震动沿顺桥向和横桥向输入时更不利。四种桥型在地震作用下:整体桥抗震性能最优异,但其台底位移、桥台桩基的剪力和弯矩最大;半整体桥台底位移、桥台桩基的剪力和弯矩最小,其墩顶位移、桥墩及桩基的剪力和弯矩仅比整体桥大;延伸桥面板桥和常规连续梁桥的墩-梁相对位移远大于整体桥和半整体桥,不适用于地震基本烈度高的区域。 相似文献
18.
铅阻尼器在自锚式悬索桥横向减震设计中的应用研究 总被引：1，自引：0，他引：1
某自锚式钢桁架悬索桥结构主跨408m,采用双层桥面,2根主缆为空间线形布置。本文根据自锚式悬索桥独特的动力特性,提出在悬索桥主梁与过渡墩、辅助墩之间沿横向设置铅挤压阻尼器的消能减震设计方案,以控制悬索桥的横向地震反应。根据风、行车和地震荷载等各种工况可能引起的支座剪力值,提出了铅挤压阻尼器临界滑移荷载值的确定方法。研究表明,同时采用铅挤压阻尼器和粘滞阻尼器的消能减震技术,可以有效地减小悬索桥的横向地震反应,可供工程实践参考。 相似文献
19.
Mauro Dolce Donatello Cardone Giuseppe Palermo 《Bulletin of Earthquake Engineering》2007,5(4):491-509
Three different isolation systems (IS’s) for bridges and viaducts are considered in the present study. All of them are made
of steel-PTFE sliding bearings (SB) to support the weight of the deck and auxiliary devices, based on different technologies
and materials (i.e. rubber, steel and shape memory alloys), to provide re-centring and/or additional energy dissipating capability.
An extensive numerical investigation has been carried out in order to (i) assess the reliability of different design approaches,
(ii) compare the response of different types of IS’s, (iii) evaluate the sensitivity of the structural response to friction
variability due to bearing pressure, air temperature and state of lubrication and (iv) identify the response variations caused
by changes in the ground motion, bridge and isolation characteristics. The nonlinear time-history analyses have been carried
out using a simplified pier-deck model, where the pier is modelled as an elastic cantilever beam and the mass of the deck
is connected to the pier through suitable nonlinear elements, simulating the behaviour of the IS. Both artificial and natural
seismic excitations have been used in the nonlinear dynamic analyses. 相似文献
20.
介绍一种用于桥梁抗震的多球面滑动摩擦隔震支座,分析这种支座的设计原理,阐明其构造特点,分析了其工作机理和滑动隔震过程,并由此建立了该隔震支座的力—位移关系恢复力模型。理论分析表明,该支座除具备完善的减隔震支座所要求的功能之外,还构造简单、隔震机理清楚、数学物理模型明确,能够满足实际应用中简单性的要求。此外,该支座在不同强度的外部激励下,可以表现出不同的阻尼和刚度。并且具备单独优化性能,即该支座可以基于多性能目标或多水准地震,对于给定的桥梁隔震系统的各个参数分别进行优化。这两种特性使得该支座适合多水准地震动作用下,基于性能的隔震桥梁抗震设计。 相似文献