共查询到20条相似文献，搜索用时 660 毫秒
1.
前人曾指出液化后伴随着超孔隙水压重新分配的渗透会引起流体破坏的可能性。为了研究这一现象,利用实验室三轴试验将孔隙水注入土壤检测了土壤的渗透剪切破坏。该实验是在各项异性的固结作用后保持差应力,使用孔隙水控制装置在体积不变的应变控制条件下将孔隙水注入。实验中所用的材料是在1995年神户地震时被液化的常规洁净细砂和风化的花岗岩土壤。本文以实验结果为基础,讨论了由孔隙水注入引起的渗透剪切破坏判据和导致后液化行为的剪切应变发展特征。 相似文献
2.
In this study, cyclic hollow cylinder torsional tests were conducted on the reconstituted specimens of Toyoura sand in a practical range of initial density and stress states. The results were employed to evaluate the liquefaction resistance and residual pore water pressure of sand using the strain energy concept. A simple pore water pressure (PWP) model with two calibration parameters was developed for the prediction of residual pore pressure as a function of cumulative strain energy density and the capacity energy of sand. Capacity energy is defined as the cumulative strain energy that is required for liquefaction onset. Based on the results of the tests, an equation is then presented for the estimation of capacity energy in terms of relative density and initial effective confining pressure of sand. This equation is shown to work well as a state boundary curve, which can discriminate between the liquefied and non-liquefied field case histories. Several extra tests were also performed to investigate the effect of initial static shear stress on the proposed PWP model and capacity energy. The results show that initial shear stress has a minor effect on the trend of the proposed PWP model; however, it definitely affects the capacity energy. The final part of the paper aims to confirm reasonable performance of the proposed PWP model by the available observations of seismically induced pore water pressure in shaking table, centrifuge, and real site conditions. 相似文献
3.
In this study the stress–strain characteristics of sand-ground rubber mixtures are investigated in the sandlike zone,at different confining pressures,using hollow cylinder specimens subjected to torsional monotonic and cyclic loading.Under monotonic loading a mixture of sand-ground rubber with 10% and 25% rubber content show more contraction behaviour than that observed in a pure sand specimen.Phase transformation point in these mixtures are located on a larger shear strain.As expected,the shear strength of specimens decreases with increase of ground rubber content.However,with increasing of effective confining pressure,the loss in shear strength of the mixture is decreased.In addition,a mixture with 25% ground rubber shows a smaller loss in shear strength compared to a mixture with 10% ground rubber mixture.Under cyclic loading mixtures with 10% and 25% ground rubber have similar liquefaction resistance,especially at confining pressures of 110 k Pa and 260 k Pa.Therefore,by using of the mixture with 25% ground rubber,a larger volume of scrap tires could be recycled.The addition of ground rubber to sand would affect the shear strain variation and excess pore water pressure trends,and this effect was further intensified with increasing ground rubber percentage. 相似文献
4.
采用多工况振动台实验研究液化对土层水平往返变形的影响.以干砂实验为参照,分析孔压增长与土层加速度和土层往返变形之间的关系.结果表明:液化将引起土表加速度显著降低,减小惯性力传递,但同时会引起土层往返剪应变明显增大.对往返变形而言,液化土层往返剪应变就可达到1%～5%的大变形状态,且液化土层往返剪应变沿深度呈下大上小分布.土层中孔压比0.4～0.8是往返变形出现放大的敏感段,在孔压比0.8左右而不是在1.0达到最大.作为其结果,土层液化将对刚性上部结构振动起减震作用,但同时增大的往返剪应变也易导致基础和地下结构破坏,特别是对液化层与下部非液化层交界处的构件更敏感. 相似文献
5.
6.
松散的饱和砂土在液化之前可作为固体看待,但当过量的孔隙水压达到初始侧应力时它成为液体,之后又恢复其强度。这个过程不能各自单独处理,而应视为一个从固态到液态,或从液态到固态的连续变化过程。因此,整个伴随着地基液化———土体流动现象全过程应作为一个在固态和液态之间相变的系列过程。本文导出了一个简单的基本方程式,可以表达松散饱和砂土在液化和地基侧向滑移现象期间的固-液相转换。该基本方程式可用作桩基系统的动力分析,其适用性通过与弹塑性基本方程的比较得到验证。 相似文献
7.
Laboratory tests on the large post-liquefaction deformation of saturated Nanjing fine sand were performed by using a hollow cylinder apparatus. The stress-strain responses and the characteristics of excess pore water pressure after liquefaction were studied. It was found that the relationship between deviatoric stress and axial strain presented a sigmoid curve, and there was a good linearity relationship between normalized pore water pressure and deviatoric stress. On this basis, a constitutive model of stress-strain responses and a dissipation model of excess pore water pressure were established. It was found that the results predicted by the two models were in good agreement with the experimental data. The influence of relative densities and confi ning pressure on the characteristics of liquef ied soil were studied. The results showed the relative densities and initial effective confining pressure all had an important influence on the stress-strain responses of liquefi ed saturated Nanjing fine sand. However, the dissipation model of excess pore water pressure after liquefaction was only affected by the confining pressure. 相似文献
8.
Cyclic shearing and liquefaction of soil under irregular loading: an incremental model for the dynamic earthquake-induced deformation 总被引：1，自引：0，他引：1
V. A. Osinov 《Soil Dynamics and Earthquake Engineering》2003,23(7):535-548
The paper presents a mathematical model for the deformation of soil under irregular cyclic loading in the simple-shear conditions. The model includes the possible change in the effective pressure in saturated soil due to the cyclic shearing, the reciprocal influence of the effective pressure on the response of the soil to the shear loading, and the pore pressure dissipation due to the seepage of the pore fluid. The hysteresis curves for the strain–stress relationship are constructed in such a way that they produce both the required backbone curve and the required damping ratio as functions of the strain amplitude. At the same time, the approach enables the constitutive functions involved in the model to be specified in various ways depending on the soil under study. The constitutive functions can be calibrated independently of each other from the conventional cyclic shear tests. The constitutive model is incorporated in the boundary value problem for the dynamic site response analysis of level ground. A numerical solution is presented for the dynamic deformation and liquefaction of soil at the Port Island site during the 1995 Hyogoken-Nambu earthquake. 相似文献
9.
目前相关规范主要依据工程场地单点的测试数据进行砂土液化判别,而实际的三维土层结构可能非常复杂。研究土层结构对砂土液化的影响机制,有利于提高砂土液化判别结果准确度。分析2008 年5 月28 日发生的松原MS地震和2010—2011 年新西兰坎特伯雷地震序列中砂土液化点的分布,结果显示:砂土液化点主要位于高弯度河流的沉积相地层,凹岸侧蚀、凸岸沉积形成的边滩具有典型的二元结构,其顶部分布的黏土类不透水层有利于下伏饱和粉细砂等易液化土层的超孔隙水压累积;而辫状河流沉积相中,上覆黏土类不透水层间断分布特征明显。针对河流不同沉积相的土层结构建立简化场地模型,使用FLAC3D 进行砂土液化数值模拟,揭示出不同土层结构中超孔隙水压力的累积、消散和渗流过程机制,结果表明,河流沉积相土层结构对砂土液化场点的分布和地表变形具有显著影响。在合理的工程地质分区基础上,现有的液化判别方法有必要考虑场地的土层结构的影响。 相似文献
10.
复杂应力条件下饱和松砂单调与循环剪切特性的比较研究 总被引：4，自引：0，他引：4
本文利用大连理工大学新引进与开发的“土工静力-动力液压-三轴扭转多功能剪切仪”,针对福建标准砂,在不排水条件下同时进行了单调剪切试验与循环剪切试验,进而对其进行了对比分析。通过比较表明,应力-应变关系的应变软化和硬化特性与流滑变形和循环流动特性密切相关,当循环剪切应力水平高于单调剪切过程中应变软化阶段最小强度时将会发生流滑变形。无论在单调剪切中,还是在循环剪切中,稳定状态时的有效偏应力比随着大主应力方向与竖向之间夹角的增大而减小,在中主应力系数相同的条件下,循环剪切中呈现显著剪胀时的有效偏应力比和最终稳定状态时的有效偏应力比峰值分别与单调剪切中达到相变状态时的有效偏应力比和最终稳定有效偏应力比基本上一致。然而不排水条件下单调与循环剪切过程中孔隙水压力的增长特性却并不相同,循环剪切中的最大孔隙水压力随着初始主应力方向角的增大而减小,单调剪切中的最大孔隙水压力却随着主应力方向角的增大而增大。 相似文献
11.
M. Kawano K. Asano H. Dohi S. Matsuda 《Soil Dynamics and Earthquake Engineering》2000,20(5-8):493-507
The linear and non-linear responses of surface soil layers have been predicted through the simultaneous simulation test against the observed ground motions at the six sites in Kobe City during the 1995 Hyogo-ken Nanbu earthquake. The total stress analysis method and the effective stress analysis method have been applied for the rough and detailed verification of the predicted non-linear dynamic behavior at the PIS and RKI sites including the liquefaction phenomenon. The shear strain distribution along depth, the ratio of excess pore water pressure to initial effective stress, the liquefaction strength parameters to initial effective stress, and the stress–strain curve during the earthquake at the PIS site have been investigated when the predicted ground motion could simulate successfully the observed acceleration time histories and response spectra in the non-linear range. 相似文献
12.
Seepage erosion in layered stream bank material 总被引：1，自引：0，他引：1
Current stream restoration practices often require anthropogenic manipulation of natural field soils to reconstruct stream banks in the absence of stabilizing vegetation. For this study, researchers conducted laboratory experiments on reconstructed, non‐vegetated stream banks with layered soils experiencing seepage. The objective of the study was to determine the effect of seepage, pore water pressure, and bank geometry on erosion and bank stability of layered streambanks. The experimental design consisted of an intermediate‐size soil lysimeter packed with a sandy clay loam top soil and an underlying fine sand layer at three bank slopes (90°, 45° and 26°). Shallow groundwater flow and seepage resulted in bank failure of geometrically stable banks. Pop out failures, liquid deformation, and piping were all observed failure mechanisms in the underlying sand material, dependent on the bank angle. Groundwater seepage processes created small‐scale failures of the underlying sand leading to larger‐scale failures of the overlying sandy clay loam. The underlying sand layer eroded according to the initial bank angle and change in overburden loading. The overlying loam layer failed along linear failure planes. The gradually sloped bank (i.e. 26° slope) failed faster, hypothesized to be due to less confining pressure and greater vertical seepage forces. Researchers analyzed the laboratory experiments using the Bank Stability and Toe Erosion Model, version 4·1. The model calculated an accurate shear surface angle similar to the failure angle observed in the lysimeter tests. The model predicted failure only for the undercut 90° bank slope, and indicated stable conditions for the other geometries. Steeper initial bank slopes and undercut banks decreased the bank factor of safety. The observed failure mechanisms and measured saturation data indicated an interaction between overburden pressure, seepage forces, and bank slope on bank stability. Future bank stability modeling would benefit by incorporating lateral seepage erosion and soil liquefaction prediction calculations. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
13.
The effect of plastic fines on the pore pressure generation characteristics of saturated sands 总被引：2，自引：0，他引：2
Mehdi Derakhshandi Ellen M. Rathje Kenan Hazirbaba S.M. Mirhosseini 《Soil Dynamics and Earthquake Engineering》2008,28(5):376-386
Pore water pressure generation during earthquake shaking initiates liquefaction and affects the shear strength, shear stiffness, deformation, and settlement characteristics of soil deposits. The effect of plastic fines (kaolinite) on pore pressure generation in saturated sands was studied through strain-controlled cyclic triaxial tests. In addition to pore pressure generation, this experimental study also focused on evaluating the threshold shear strain for pore pressure generation and the volumetric compressibility of specimens during pore pressure dissipation. The results reveal that specimens having up to 20% plastic fines content generated larger values of pore water pressure than clean sand specimens. At 30% fines content, the excess pore water pressure decreased below that of clean sand. The threshold shear strain, which indicates the strain level above which pore pressures begin to generate, was assessed for different kaolinite–sand mixtures. The threshold shear strain was similar for 0–20% fines (γt0.006–0.008%), but increased to about 0.025% for 30% fines. The volumetric compressibility, measured after pore pressure generation, was similar for all specimens. The transition of behavior at fines contents between 20% and 30% can be attributed to a change in the soil structure from one dominated by sand grains to one dominated by fines. 相似文献
14.
An effective stress method is presented for the analysis of liquefaction of ground including soil-structure interaction, based on an explicit-implicit finite element method. A simple constitutive model is developed to be incorporated in the effective stress method. The constitutive model consists of the Ramberg-Osgood model extended to two-dimensional problems and a new dilatancy model. The effectiveness of the constitutive model is examined with results of a simple shear test. Besides, the effective stress method is verified by comparing its numerical results with results of a shaking table test. It is found that the present method can simulate well the response of a saturated dense sand-structure system. The difference of the response computed by the effective stress method and the total stress method is discussed. It is found that the total stress method can simulate the response of the saturated sand within an accumulating excess pore water pressure of less than 70 per cent of the initial overburden stress. 相似文献
15.
To understand the post-liquefaction behavior of liquefied ground, it is important to get a better understanding and a more suitable characterization of the variation of excess pore pressure after liquefaction. In this paper, the soil permeability is considered as one of the key soil parameters for clarifying the mechanism of post-liquefaction behavior of liquefied ground. For this reason, a series of shaking table tests were conducted for a Toyoura sand deposit with different soil permeability values. Polymer fluid was used in model tests to vary the permeability of sand deposits. Excess pore pressures and settlements were measured in each test. A basic mechanism in post-liquefaction behavior and the solidification phenomenon after liquefaction were discussed based on these test results. Also, a new method for predicting the dissipation of excess pore pressure was developed. This study provides evidence of the important effect of soil permeability on the velocity with which the solidification front moves upward in liquefied ground. It is suggested that the value of coefficient of permeability of liquefied sand can increase to about 4.0 times the initial value. This variation of permeability after liquefaction should be taken into account in post-liquefaction analysis. 相似文献
16.
饱和砂土液化是由地震引起的一种最常见的工程地质现象,也是造成重大地震灾害的主要原因之一。由于成因的复杂性和所造成灾害的严重性,饱和砂土液化一直是土动力学和岩土地震工程研究领域的重要课题。针对饱和砂土液化问题,基于开源地震工程数值计算平台OpenSees,对材料库中的4种砂土本构模型进行数值计算。采用二维u-p单元模拟土颗粒位移和孔隙水压力,分析和对比4种模型在循环动力荷载作用下的加速度、超孔隙水压力、位移、剪应力-剪应变和平均有效应力路径方面的响应结果。研究结果表明:(1)砂土对输入加速度表现出一定的放大效应,对于不同的模型,该放大效应存在一些差异;(2) Stress Density模型在循环动力荷载作用下易产生永久变形;(3)在循环动力荷载作用下,PDMY模型和CycLiqCPSP模型的强度逐渐降低,直到完全消失;(4) Stress Density模型和Manzari Dafalias模型在循环动力荷载下表现出明显的剪胀效应。研究成果对砂土液化的数值模拟问题具有重要的理论价值,可为饱和砂土的液化模拟和砂土本构模型的选取提供参考。 相似文献
17.
The state of zero effective stress is a situation at which the effective stress of saturated sand decreases to zero in the process of liquefaction. In the state of zero effective stress, sand particles suspend in water and the foundation is vulnerable to much large lateral deformation. The state of zero effective stress can be achieved through dynamic loading tests, but the obtained state is difficult to sustain a steady situation. To simulate the suspended sand in water under fully liquefied condition, plastic sand, characterized by small specific gravity, is used instead of quartz sand to build an inclined foundation. Salt water with similar density is used to pass in slowly near bottom of the foundation. As observed in tests, the plastic sand is able to suspend in sodium chloride solution (salt water) of a specific density and thus this model can be used to simulate the lateral spreading of a foundation under zero effective stress state. Lateral deformation occurs within a certain depth beneath the ground and the magnitude increases from the bottom up, showing nonlinear behaviors. This paper presents a physical modeling approach for achieving the state of zero effective stress under static laboratory condition. 相似文献
18.
Three groups of dynamic triaxial tests were performed for saturated Nanjing fine sand subjected to uniform cyclic loading.
The tested curves of the excess pore water pressure (EPWP) ratio variation with the ratio of the number of cycles are provided.
The concept of the EPWP increment ratio is introduced and two new concepts of the effective dynamic shear stress ratio and
the log decrement of effective stress are defined. It is found that the development of the EPWP increment ratio can be divided
into three stages: descending, stable and ascending. Furthermore, at the stable and ascending stages, a satisfactory linear
relationship is obtained between the accumulative EPWP increment ratio and natural logarithm of the effective dynamic shear
stress ratio. Accordingly, the EPWP increment ratio at the number of cycles N has been deduced that is proportional to the log decrement of effective stress at the cycle number N-1, but is independent of the cyclic stress amplitude. Based on the analysis, a new EPWP increment model for saturated Nanjing
fine sand is developed from tested data fitting, which provides a better prediction of the curves of EPWP generation, the
number of cycles required for initial liquefaction and the liquefaction resistance. 相似文献
19.
20.
针对地震(或静力)液化作用对尾矿坝渗流场和孔压分布的影响进行研究,基于多孔介质渗流理论,考虑到尾矿坝渗流特性,编写分析程序SAFTD。根据程序假设的初始浸润面,通过调整浸润面处网格迭代求解最终浸润面的位置,选取一个经典算例验证程序的可靠性。针对典型的上游法尾矿库,采用SAFTD程序分析液化前后尾矿坝的渗流场与孔压分布特征。数值模拟结果表明,液化后尾矿坝的浸润面中间部分发生明显抬升,而在入渗点处和出渗点附近变化不大;液化后尾矿坝的孔压明显增加,坝体内部孔压增大约18%~280%,最大的孔压增量发生在初期坝的右下部,数值模拟结果与Ishihara对Mochikoshi 2号坝的分析结果相似。 相似文献