首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 484 毫秒
1.
We present results of processed microseismic events induced by hydraulic fracturing and detected using dual downhole monitoring arrays. The results provide valuable insight into hydraulic fracturing. For our study, we detected and located microseismic events and determined their magnitudes, source mechanisms and inverted stress field orientation. Event locations formed a distinct linear trend above the stimulated intervals. Source mechanisms were only computed for high‐quality events detected on a sufficient number of receivers. All the detected source mechanisms were dip‐slip mechanisms with steep and nearly horizontal nodal planes. The source mechanisms represented shear events and the non‐double‐couple components were very small. Such small, non‐double‐couple components are consistent with a noise level in the data and velocity model uncertainties. Strikes of inverted mechanisms corresponding to the nearly vertical fault plane are (within the error of measurements) identical with the strike of the location trend. Ambient principal stress directions were inverted from the source mechanisms. The least principal stress, σ3, was determined perpendicular to the strike of the trend of the locations, indicating that the hydraulic fracture propagated in the direction of maximum horizontal stress. Our analysis indicated that the source mechanisms observed using downhole instruments are consistent with the source mechanisms observed in microseismic monitoring arrays in other locations. Furthermore, the orientation of the inverted principal components of the ambient stress field is in agreement with the orientation of the known regional stress, implying that microseismic events induced by hydraulic fracturing are controlled by the regional stress field.  相似文献   

2.
Comparison of surface and borehole locations of induced seismicity   总被引：1，自引：0，他引：1  
Monitoring of induced microseismic events has become an important tool in hydraulic fracture diagnostics and understanding fractured reservoirs in general. We compare microseismic event and their uncertainties using data sets obtained with surface and downhole arrays of receivers. We first model the uncertainties to understand the effect of different acquisition geometries on location accuracy. For a vertical array of receivers in a single monitoring borehole, we find that the largest part of the final location uncertainty is related to estimation of the backazimuth. This is followed by uncertainty in the vertical position and radial distance from the receivers. For surface monitoring, the largest uncertainty lies in the vertical position due to the use of only a single phase (usually P‐wave) in the estimation of the event location. In surface monitoring results, lateral positions are estimated robustly and are not sensitive to the velocity model. In this case study, we compare event location solutions from two catalogues of microseismic events; one from a downhole array and the second from a surface array of 1C geophone. Our results show that origin time can be reliably used to find matching events between the downhole and surface catalogues. The locations of the corresponding events display a systematic shift consistent with a poorly calibrated velocity model for downhole dataset. For this case study, locations derived from surface monitoring have less scatter in both vertical and horizontal directions.  相似文献   

3.
Microseismic monitoring is an approach for mapping hydraulic fracturing. Detecting the accurate locations of microseismic events relies on an accurate velocity model. The one‐dimensional layered velocity model is generally obtained by model calibration from inverting perforation data. However, perforation shots may only illuminate the layers between the perforation shots and the recording receivers with limited raypath coverage in a downhole monitoring problem. Some of the microseismic events may occur outside of the depth range of these layers. To derive an accurate velocity model covering all of the microseismic events and locating events at the same time, we apply the cross double‐difference method for the simultaneous inversion of a velocity model and event locations using both perforation shots and microseismic data. The cross double‐difference method could provide accurate locations in both the relative and absolute sense, utilizing cross traveltime differences between P and S phases over different events. At the downhole monitoring scale, the number of cross traveltime differences is sufficiently large to constrain events locations and velocity model as well. In this study, we assume that the layer thickness is known, and velocities of P‐ and S‐wave are inverted. Different simultaneous inversion methods based on the Geiger's, double‐difference, and cross double‐difference algorithms have been compared with the same input data. Synthetic and field data experiments suggest that combining both perforation shots and microseismic data for the simultaneous cross double‐difference inversion of the velocity model and event locations is available for overcoming the trade‐offs in solutions and producing reliable results.  相似文献   

4.
We present an automatic method of processing microseismic data acquired at the surface by a star‐like array. The back‐projection approach allows successive determination of the hypocenter position of each event and of its focal mechanisms. One‐component vertical geophone groups and three‐component accelerometers are employed to monitor both P‐ and S‐waves. Hypocenter coordinates are determined in a grid by back‐projection stacking of the short‐time‐average‐to‐long‐time‐average ratio of absolute amplitudes at vertical components and polarization norm derived from horizontal components of the P‐ and S‐waves, respectively. To make the location process more efficient, calculation is started with a coarse grid and zoomed to the optimum hypocenter using an oct‐tree algorithm. The focal mechanism is then determined by stacking the vertical component seismograms corrected for the theoretical P‐wave polarity of the focal mechanism. The mechanism is resolved in the coordinate space of strike, dip, and rake angles. The method is tested on 34 selected events of a dataset of hydraulic fracture monitoring of a shale gas play in North America. It was found that, by including S‐waves, the vertical accuracy of locations improved by a factor of two and is equal to approximately the horizontal location error. A twofold enhancement of horizontal location accuracy is achieved if a denser array of geophone groups is used instead of the sparse array of three‐component seismometers. The determined focal mechanisms are similar to those obtained by other methods applied to the same dataset.  相似文献   

5.
We develop a methodology to obtain a consistent velocity model from calibration shots or microseismicity observed on a buried array. Using a layered 1D isotropic model derived from checkshots as an initial velocity model, we invert P‐wave arrival times to obtain effective anisotropic parameters with a vertical axis of symmetry (VTI). The nonlinear inversion uses iteration between linearized inversion for anisotropic parameters and origin times or depths, which is specific to microseismic monitoring. We apply this technique to multiple microseismic events from several treatments within a buried array. The joint inversion of selected events shows a largely reduced RMS error indicating that we can obtain robust estimates of anisotropic parameters, however we do not show improved source locations. For joint inversion of multiple microseismic events we obtained Thomsen anisotropic parameters ε of 0.15 and δ of 0.05, which are consistent with values observed in active seismic surveys. These values allow us to locate microseismic events from multiple hydraulic fracture treatments separated across thousands of metres with a single velocity model. As a result, we invert the effective anisotropy for the buried array region and are able to provide a more consistent microseismicity mapping for past and future hydraulic fracture stimulations.  相似文献   

6.
A theoretical method is proposed to estimate post‐fracturing fracture size and transmissivity, and as a test of the methodology, data collected from two wells were used for verification. This method can be employed before hydrofracturing in order to obtain estimates of the potential hydraulic benefits of hydraulic fracturing. Five different pumping test analysis methods were used to evaluate the well hydraulic data. The most effective methods were the Papadopulos‐Cooper model (1967), which includes wellbore storage effects, and the Gringarten‐Ramey model (1974), known as the single horizontal fracture model. The hydraulic parameters resulting from fitting these models to the field data revealed that as a result of hydraulic fracturing, the transmissivity increased more than 46 times in one well and increased 285 times in the other well. The model developed by dos Santos (2008) , which considers horizontal radial fracture propagation from the hydraulically fractured well, was used to estimate potential fracture geometry after hydrofracturing. For the two studied wells, their fractures could have propagated to distances of almost 175 m or more and developed maximum apertures of about 2.20 mm and hydraulic apertures close to 0.30 mm. Fracturing at this site appears to have expanded and propagated existing fractures and not created new fractures. Hydraulic apertures calculated from pumping test analyses closely matched the results obtained from the hydraulic fracturing model. As a result of this model, post‐fracturing geometry and resulting post‐fracturing well yield can be estimated before the actual hydrofracturing.  相似文献   

7.
水力压裂对速度场及微地震定位的影响   总被引：2，自引：1，他引：1       下载免费PDF全文
水力压裂是页岩气开发过程中的核心增产技术,微地震则广泛用于压裂分析、水驱前缘监测和储层描述.微地震反演过程中,用于反演的速度模型往往基于测井、地震或标定炮资料构建,忽略了压裂过程中裂缝及孔隙流体压力变化对地层速度的影响.本文首先基于物质守恒、渗流理论和断裂力学模拟三维水力压裂过程,得到地下裂缝发育特征和孔隙压力分布.继而根据Coates-Schoenberg方法和裂缝柔量参数计算裂缝和孔隙压力对速度场的影响,得到压裂过程中的实时速度模型.最后利用三维射线追踪方法正演微地震走时和方位信息,并采用常规微地震定位方法反演震源位置及进行误差分析.数值模拟结果表明,检波器空间分布影响定位精度,常规方法的定位误差随射线路径在压裂带中传播距离增加而变大,且不同压裂阶段的多点反演法与单点极化法精度相当.  相似文献   

8.
Seismic anisotropy which is common in shale and fractured rocks will cause travel-time and amplitude discrepancy in different propagation directions. For microseismic monitoring which is often implemented in shale or fractured rocks, seismic anisotropy needs to be carefully accounted for in source location and mechanism determination. We have developed an efficient finite-difference full waveform modeling tool with an arbitrary moment tensor source. The modeling tool is suitable for simulating wave propagation in anisotropic media for microseismic monitoring. As both dislocation and non-double-couple source are often observed in microseismic monitoring, an arbitrary moment tensor source is implemented in our forward modeling tool. The increments of shear stress are equally distributed on the staggered grid to implement an accurate and symmetric moment tensor source. Our modeling tool provides an efficient way to obtain the Green’s function in anisotropic media, which is the key of anisotropic moment tensor inversion and source mechanism characterization in microseismic monitoring. In our research, wavefields in anisotropic media have been carefully simulated and analyzed in both surface array and downhole array. The variation characteristics of travel-time and amplitude of direct P- and S-wave in vertical transverse isotropic media and horizontal transverse isotropic media are distinct, thus providing a feasible way to distinguish and identify the anisotropic type of the subsurface. Analyzing the travel-times and amplitudes of the microseismic data is a feasible way to estimate the orientation and density of the induced cracks in hydraulic fracturing. Our anisotropic modeling tool can be used to generate and analyze microseismic full wavefield with full moment tensor source in anisotropic media, which can help promote the anisotropic interpretation and inversion of field data.  相似文献   

9.
In hydraulic fracturing treatments, locating not only hydraulic fractures but also any pre‐existing natural fractures and faults in a subsurface reservoir is very important. Hydraulic fractures can be tracked by locating microseismic events, but to identify the locations of natural fractures, an additional technique is required. In this paper, we present a method to image pre‐existing fractures and faults near a borehole with virtual reverse vertical seismic profiling data or virtual single‐well profiling data (limited to seismic reflection data) created from microseismic monitoring using seismic interferometry. The virtual source data contain reflections from natural fractures and faults, and these features can be imaged by applying migration to the virtual source data. However, the imaging zone of fractures in the proposed method is strongly dependent on the geographic extent of the microseismic events and the location and direction of the fracture. To verify our method, we produced virtual reverse vertical seismic profiling and single‐well profiling data from synthetic microseismic data and compared them with data from real sources in the same relative position as the virtual sources. The results show that the reflection travel times from the fractures in the virtual source data agree well with travel times in the real‐source data. By applying pre‐stack depth migration to the virtual source data, images of the natural fractures were obtained with accurate locations. However, the migrated section of the single‐well profiling data with both real and virtual sources contained spurious fracture images on the opposite side of the borehole. In the case of virtual single‐well profiling data, we could produce correct migration images of fractures by adopting directional redatuming for which the occurrence region of microseismic events is divided into several subdivisions, and fractures located only on the opposite side of the borehole are imaged for each subdivision.  相似文献   

10.
—?The stress state at the Hijiori hot dry rock site was estimated based on the inversion from focal mechanisms of microseismic events induced during hydraulic injection experiments. The best fit stress model obtained by inverting 58 focal mechanisms of seismic events simultaneously indicates that the maximum principal stress σ1 is vertical, while the minimum principal stress σ3 is horizontal and trends north-south. The average misfit between the stress model and all the data is 6.8°. The inversion results show that the average misfit is small enough to satisfy the assumption of homogeneity in the focal mechanism data and that the 95% confidence regions of σ1 and σ3 are well constrained, i.e., they do not overlap, suggesting that the inversion results are acceptable. The stress estimates obtained by the focal mechanism inversion essentially agree with other stress estimates previously obtained. It is therefore concluded that the focal mechanism inversion method provides a useful tool for estimating the stress state. The hypocentral distributions of microseismic events associated with the hydraulic fracturing experiments are distributed around the plane that spreads to almost east–west from the injection wells and declines to the north at a high angle. The vertical orientation and east–west strike of the seismic events are essentially coplanar with the caldera ring-fault structure in the southern portion of the Hijiori Caldera. This indicates that tensile fractures of intact rock were not being created, but pre-existing fractures were being re-opened and developed in the direction of the maximum horizontal principal stress, although microseismic events were caused by shear failures.  相似文献   

11.
Microseismic monitoring has proven invaluable for optimizing hydraulic fracturing stimulations and monitoring reservoir changes. The signal to noise ratio of the recorded microseismic data varies enormously from one dataset to another, and it can often be very low, especially for surface monitoring scenarios. Moreover, the data are often contaminated by correlated noises such as borehole waves in the downhole monitoring case. These issues pose a significant challenge for microseismic event detection. In addition, for downhole monitoring, the location of microseismic events relies on the accurate polarization analysis of the often weak P‐wave to determine the event azimuth. Therefore, enhancing the microseismic signal, especially the low signal to noise ratio P‐wave data, has become an important task. In this study, a statistical approach based on the binary hypothesis test is developed to detect the weak events embedded in high noise. The method constructs a vector space, known as the signal subspace, from previously detected events to represent similar, yet significantly variable microseismic signals from specific source regions. Empirical procedures are presented for building the signal subspace from clusters of events. The distribution of the detection statistics is analysed to determine the parameters of the subspace detector including the signal subspace dimension and detection threshold. The effect of correlated noise is corrected in the statistical analysis. The subspace design and detection approach is illustrated on a dual‐array hydrofracture monitoring dataset. The comparison between the subspace approach, array correlation method, and array short‐time average/long‐time average detector is performed on the data from the far monitoring well. It is shown that, at the same expected false alarm rate, the subspace detector gives fewer false alarms than the array short‐time average/long‐time average detector and more event detections than the array correlation detector. The additionally detected events from the subspace detector are further validated using the data from the nearby monitoring well. The comparison demonstrates the potential benefit of using the subspace approach to improve the microseismic viewing distance. Following event detection, a novel method based on subspace projection is proposed to enhance weak microseismic signals. Examples on field data are presented, indicating the effectiveness of this subspace‐projection‐based signal enhancement procedure.  相似文献   

12.
在水力压裂施工中,如何有效获取压裂过程中产生的裂缝形态以及裂缝的动态扩展过程一直是困扰学术界和工业界的问题。目前,常规利用微地震事件定位结果进行分析的方法存在需要人工干预、散点信息表示能力不足等问题;采用数值模拟分析的方法往往因复杂的地下介质情况而引入计算偏差。本文基于非监督学习算法,通过提取微地震事件的空间和时间信息,实现对裂缝平面的识别以及裂缝网络拓展路径的分析;并通过引入水力压裂岩石物理实验,利用实际监测获得的声发射数据以及对应的真实破裂情况的CT扫描数据,检验方法的可行性。最终结果表明,本文所提方法对主断裂有较好的识别效果,识别结果与CT扫描的真实结果吻合性较好。  相似文献   

13.
The stimulation of a geothermal well in Basel, Switzerland produced a distribution of microseismic event locations with an overall alignment in the direction of the maximum horizontal stress. Fault plane solutions of individual larger events indicated movements on fracture planes at an angle to the maximum horizontal stress that could not be reliably interpreted from the event locations. To obtain higher resolution images of the microseismic event locations, events with similar waveforms have been identified by multiplet analysis. A number of receivers were used in the multiplet processing to ensure each multiplet is represented by a unique group of waveforms. The location accuracy within each multiplet has been significantly improved using cross‐correlation to refine the shear‐wave traveltime picks. The distribution of events within each multiplet can be interpreted as being due to movements on a single fracture or a number of near parallel fractures. It is shown that whilst the overall distribution of events is around the direction of the maximum horizontal stress, the individual multiplets representing fracture planes have a variety of azimuths and dips.  相似文献   

14.
The hydrocarbon industry is moving increasingly towards tight sandstone and shale gas resources – reservoirs that require fractures to be produced economically. Therefore, techniques that can identify sets of aligned fractures are becoming more important. Fracture identification is also important in the areas of coal bed methane production, carbon capture and storage (CCS), geothermal energy, nuclear waste storage and mining. In all these settings, stress and pore pressure changes induced by engineering activity can generate or reactivate faults and fractures. P‐ and S‐waves are emitted by such microseismic events, which can be recorded on downhole geophones. The presence of aligned fracture sets generates seismic anisotropy, which can be identified by measuring the splitting of the S‐waves emitted by microseismic events. The raypaths of the S‐waves will have an arbitrary orientation, controlled by the event and geophone locations, meaning that the anisotropy system may only be partly illuminated by the available arrivals. Therefore to reliably interpret such splitting measurements it is necessary to construct models that compare splitting observations with modelled values, allowing the best fitting rock physics parameters to be determined. Commonly, splitting measurements are inverted for one fracture set and rock fabrics with a vertical axis of symmetry. In this paper we address the challenge of identifying multiple aligned fracture sets using splitting measured on microseismic events. We analyse data from the Weyburn CCS‐EOR reservoir, which is known to have multiple fracture sets, and from a hydraulic fracture stimulation, where it is believed that only one set is present. We make splitting measurements on microseismic data recorded on downhole geophone arrays. Our inversion technique successfully discriminates between the single and multiple fracture cases and in all cases accurately identifies the strikes of fracture sets previously imaged using independent methods (borehole image logs, core samples, microseismic event locations). We also generate a synthetic example to highlight the pitfalls that can be encountered if it is assumed that only one fracture set is present when splitting data are interpreted, when in fact more than one fracture set is contributing to the anisotropy.  相似文献   

15.
Microseismic monitoring in petroleum settings provides insights into induced and naturally occurring stress changes. Such data are commonly acquired using an array of sensors in a borehole, providing measures of arrival times and polarizations. Events are located using 1D velocity models, P‐ and S‐wave arrival times and the azimuths of P‐wave particle motions. However in the case of all the sensors being deployed in a vertical or near‐vertical borehole, such analysis leads to an inherent 180° ambiguity in the source location. Here we present a location procedure that removes this ambiguity by using the dip of the particle motion as an a priori information to constrain the initial source location. The new procedure is demonstrated with a dataset acquired during hydraulic fracture stimulation, where we know which side of the monitoring well the events are located. Using a 5‐step location procedure, we then reinvestigate a microseismic data set acquired in April 1997 at the Ekofisk oilfield in the North Sea. Traveltimes for 2683 candidate events are manually picked. A noise‐weighted analytic‐signal polarization analysis is used to estimate the dip and azimuth of P‐wave particle motions. A modified t‐test is used to statistically assess the reliability of event location. As a result, 1462 events are located but 627 are deemed to be statistically reliable. The application of a hierarchal cluster analysis highlights coherent structures that cluster around wells and inferred faults. Most events cluster at a depth of roughly 3km in the Ekofisk chalk formation but very little seismicity is observed from the underlying Tor chalk formation, which is separated from the Ekofisk formation by an impermeable layer. We see no evidence for seismicity in the overburden but such events may be too distant to detect. The resulting picture of microseismicity at Ekofisk is very different from those presented in previous studies.  相似文献   

16.
We provide a comparative analysis of the spatio-temporal dynamics of hydraulic fracturing-induced microseismicity resulting from gel and water treatments. We show that the growth of a hydraulic fracture and its corresponding microseismic event cloud can be described by a model which combines geometry- and diffusion-controlled processes. It allows estimation of important parameters of fracture and reservoir from microseismic data, and contributes to a better understanding of related physical processes. We further develop an approach based on this model and apply it to data from hydraulic fracturing experiments in the Cotton Valley tight gas reservoir. The treatments were performed with different parameters such as the type of treatment fluid, the injection flow rate, the total volume of fluid and of proppant. In case of a gel-based fracturing, the spatio-temporal evolution of induced microseismicity shows signatures of fracture volume growth, fracturing fluid loss, as well as diffusion of the injection pressure. In contrast, in a water-based fracturing the volume creation growth and the diffusion controlled growth are not clearly separated from each other in the space-time diagram of the induced event cloud. Still, using the approach presented here, the interpretation of induced seismicity for the gel and the water treatments resulted in similar estimates of geometrical characteristics of the fractures and hydraulic properties of the reservoir. The observed difference in the permeability of the particular hydraulic fractures is probably caused by the different volume of pumped proppant.  相似文献   

17.
Hydraulic fractures generated by fluid injection in rock formations are often mapped by seismic monitoring. In many cases, the microseismicity is asymmetric relative to the injection well, which has been interpreted by stress gradient along the direction of the hydraulic fracture. We present a mathematical model of asymmetric hydrofracture growth based on relations between the solid‐phase stress and the fracture hydraulics. For single fracture and single injection point, the model has three parameters, hydraulic conductivities of the fracture wings, and normalised stress gradient and predicts the positions of the fracture tips as functions of time. The model is applied to a set of microseismic event locations that occurred during and after an injection process. Two different methods are suggested that make it possible to delineate the fracture tips from the set of microseismic events. This makes it possible to determine the model parameters and to check the agreement between the model prediction and the measured data. The comparison of the measured and modelled growth of fracture wings supports both the assumption of the non‐zero stress gradient and the existence of the post‐injection unilateral growth.  相似文献   

18.
In hydraulic fracturing experiments, perforation shots excite body and tube waves that sample, and thus can be used to characterize, the surrounding medium. While these waves are routinely employed in borehole operations, their resolving power is limited by the experiment geometry, the signal‐to‐noise ratio, and their frequency content. It is therefore useful to look for additional, complementary signals that could increase this resolving power. Tube‐to‐body‐wave conversions (scattering of tube to compressional or shear waves at borehole discontinuities) are one such signal. These waves are not frequently considered in hydraulic fracture settings, yet they possess geometrical and spectral attributes that greatly complement the resolution afforded by body and tube waves alone. Here, we analyze data from the Jonah gas field (Wyoming, USA) to demonstrate that tube‐to‐shear‐wave conversions can be clearly observed in the context of hydraulic fracturing experiments. These waves are identified primarily on the vertical and radial components of geophones installed in monitoring wells surrounding a treatment well. They exhibit a significantly lower frequency content (10–100 Hz) than the primary compressional waves (100–1000 Hz). Tapping into such lower frequencies could help to better constrain velocity in the formation, thus allowing better estimates of fracture density, porosity and permeability. Moreover, the signals of tube‐to‐shear‐wave conversion observed in this particular study provide independent estimates of the shear wave velocity in the formation and of the tube wave velocity in the treatment well.  相似文献   

19.
Locating microseismic events using borehole data   总被引：1，自引：0，他引：1  
Constraining microseismic hypocentres in and around hydrocarbon reservoirs and their overburdens is essential for the monitoring of deformation related to hydraulic fracturing, production and injection and the assessment of reservoir security for CO2 and wastewater storage. Microseismic monitoring in hydrocarbon reservoirs can be achieved via a variety of surface and subsurface acquisition geometries. In this study we use data from a single, subsurface, vertical array of sensors. We test an existing technique that uses a 1D velocity model to constrain locations by minimizing differential S‐to‐P arrival times for individual sensors. We show that small errors in either arrival time picks or the velocity model can lead to large errors in depth, especially near velocity model discontinuities where events tend to cluster. To address this issue we develop two methods that use all available arrival times simultaneously in the inversion, thus maximizing the number of potential constraints from to N, where N is the number of phase picks. The first approach minimizes all available arrival time pairs whilst the second approach, the equal distance time (EDT) method defines the hypocentre as the point where the maximum number of arrival time surfaces intersect. We test and compare the new location procedures with locations using differential S‐to‐P times at each individual sensor on a microseismic data set recorded by a vertical array of sensors at the Ekofisk reservoir in the North Sea. Specifically, we test each procedure's sensitivity to perturbations in measured arrival times and the velocity model using Monte Carlo analysis. In general, location uncertainties increase with increasing raypath length. We show that errors in velocity model estimates are the most significant source of uncertainty in source location with these experiments. Our tests show that hypocentres determined by the new procedures are less sensitive to erroneous measurements and velocity model uncertainties thus reducing the potential for misinterpretation of the results.  相似文献   

20.
Using a set of synthetic P‐ and S‐wave onsets, computed in a 1D medium model from sources that mimic a distribution of microseismic events induced by hydrofrac treatment to a monitoring geophone array(s), we test the possibility to invert back jointly the model and events location. We use the Neighbourhood algorithm for data inversion to account for non‐linear effects of velocity model and grid search for event location. The velocity model used is composed of homogeneous layers, derived from sonic logging. Results for the case of one and two monitoring wells are compared. These results show that the velocity model can be obtained in the case of two monitoring wells, if they have optimal relative position. The use of one monitoring well fails due to the trade‐off between the velocity model and event locations.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号