共查询到19条相似文献，搜索用时 296 毫秒
1.
建立双向地震作用下层间隔震双向偏心结构侧扭耦联分析模型;考虑上部结构及下部结构的弹塑性模型,隔震支座采用双向耦合非线性Bouc-wen模型模拟;分析偏心参数对层间隔震双向偏心结构的影响规律;评价双向地震作用下我国抗震规范给出的扭转影响系数静力预测值的准确性。结果表明,双向地震作用下设置中间柔性隔震层可以减小上\,下部结构扭转的耦连效应;下部结构存在双向偏心会对隔震层和下部结构扭转反应带来不利影响;LRB耦合效应对层间隔震地震响应影响较小;当下部结构偏心率较大时现行规范计算扭转系数偏于不安全。 相似文献
2.
偏心结构非线性地震反应分析的一种简化方法 总被引：1，自引：1，他引：1
本文建立了基于结构状态方程和偏心结构体系的层剪力-扭矩等效屈服EYST面概念的求解平扭耦联非线性地震反应的分离-予估-修正递推算法，编制了相应的计算程序。通过与三个单层偏心结构模型的破坏性地震模拟试验结果的对比，验证了小变形阶段平-扭耦联地震反应算法的实用性和可靠性。算例表明，该程序数据处理量小，运算快捷，便于应用。 相似文献
3.
捏拢效应与P-Δ效应对地震延性需求和损伤指标的影响 总被引：1，自引：0，他引：1
文中定量地分析了捏拢效应和P-Δ效应对非弹性单自由度体系的地震延性需求和Park-Ang地震损伤指标的概率统计特征的影响。采用Bouc-W en模型描述具有P-Δ效应、捏拢效应、强度退化、刚度退化等典型特性的恢复力-位移滞回曲线;根据非弹性单自由度体系在69条强震记录作用下的动力响应,定量地分析了捏拢效应和P-Δ效应对地震延性需求和Park-Ang地震损伤指标的均值和变异系数的影响,并建立了地震延性需求的概率预测模型。计算结果表明,捏拢效应和由重力引起的P-Δ效应对地震延性需求的影响较大,而由竖向地震激励引起的P-Δ效应对地震延性需求的影响很小;对于短周期体系,建议采用对数正态或Frechet分布来描述地震延性需求的概率分布;对于长周期体系,采用Frechet分布则更为合理。 相似文献
4.
5.
为了了解在强震作用下偏心结构平扭耦联效应,对土-偏心结构相互作用体系进行了平扭耦联弹塑性反应参数弹塑性分析。本文建立考虑SSI的单层单向偏心结构模型,将地基土假定为弹簧,通过拉格朗日能量法推导了结构体系的动力特性方程,采用静力弹塑性(Pushover)分析方法,利用MATLAB软件编程,分析了土体和结构均由弹性到弹塑性的变化对相互作用体系和上部结构的影响,以及体系由弹性到弹塑性平扭耦联效应的变化过程,发现土体由弹性进入塑性对体系的动力特性影响很大,并且得到了相互作用体系相对振型频率随扭平频率比和偏心率的变化规律。 相似文献
6.
铅芯叠层橡胶支座恢复力模型研究 总被引：5，自引：0，他引：5
在Wen和Park模型的基础上，对铅芯叠层橡胶支座单向和双向耦合恢复力模型进行了改进，使其可以更为准确的模拟铅芯叠层橡胶支座单向和双向耦合的滞回性能。并由计算分析可以看出，考虑双向耦合作用与未考虑双向耦合作用的恢复力滞回曲线有较大差别，因而支座应采用双向耦合恢复力模型以考虑支座的双向耦合作用对结构地震反应的影响。 相似文献
7.
多层偏心结构非线性地震反应分析 总被引：1，自引：1，他引：1
本文利用层单元模型，建立了基于层剪力-扭矩等效屈服EYST面概念的求解多层偏心结构体系双水平向地震动作用下平扭耦联非线性地震反应的简化算法，并讨论了控制偏心结构非线性扭转反应的相关结构参数；通过数值分析，初步验证了该简化方法的实用性和可靠性。 相似文献
8.
LRB隔震储罐地震反应的双向耦合效应 总被引：1，自引：0，他引：1
建立了双向地震作用下LRB基础隔震储罐地震反应的数值模型,对单向和双向地震作用下隔震储罐的地震反应和隔震支座的力学性能进行了对比研究。提出了衡量双向耦合效应影响的评价指标,分析了不同类型场地上隔震储罐地震反应的双向耦合效应影响规律。研究表明,双向耦合效应使支座滞回曲线变得不规则,呈现出粘滞特性。双向耦合效应不会引起隔震储罐基底剪力、弯矩、晃动波高的明显增大,但忽视双向耦合效应会严重低估支座位移,尤其是在II类和IV类场地上更为明显。因此在LRB隔震储罐双向地震反应分析时,不能简单选取两个单向地震作用下响应的组合值作为地震响应值,必须考虑双向耦合效应的影响。 相似文献
9.
多维地震作用下偏心结构的磁流变阻尼器半主动控制 总被引：9，自引：1，他引：8
理论研究与震害经验表明,地震时结构会产生不可忽略的平动与扭转耦合的空间振动。本文提出了基于线性最优控制理论的部分状态反馈次优控制策略和基于遗传算法的控制策略,以Marlab和Simulink为平台,采用磁流变阻尼器对双向水平地震作用下的偏心结构平．扭耦联反应进行半主动控制。对-6层双向偏心框架结构进行控制效果仿真分析的结果证明,本文提出的2种控制策略是有效的。 相似文献
10.
以HDR隔震梁桥多自由度（MDOF）模型和等效双线性单自由度（SDOF）模型为研究对象，以典型近场地震动作为输入，研究HDR支座双向耦合效应对HDR隔震梁桥地震响应的影响。研究结果表明:不考虑双向耦合效应的HDR支座滞回曲线呈典型双线性；考虑双向耦合效应的HDR支座滞回曲线面积小于不考虑双向耦合效应的HDR支座滞回曲线面积。不考虑双向耦合效应的顺桥向HDR支座位移峰值db大于考虑双向耦合效应时，但横桥向的结果相反。近场地震作用下，对梁桥进行HDR支座隔震设计时，忽略双向耦合效应计算得到的墩底剪力峰值和弯矩峰值均偏于保守。可忽略HDR支座双向耦合效应对HDR隔震梁桥近场地震能量的影响。 相似文献
11.
The study of the torsional response of buildings in the inelastic range of behaviour is of great interest since the ability of structures to resist strong earthquakes mainly relies on their ductility and capacity for energy dissipation. Furthermore, an examination of the performance of structures during past earthquakes demonstrates that plan-asymmetric buildings suffered greater damage due to torsional response. The paper deals with this subject by analysing a model which idealizes a one-storey building with resisting elements oriented along two perpendicular directions. In addition to the parameters of the elastic behaviour, the inelastic system response depends on full yield capacity and plan-wise strength distribution. The influence of the criterion adopted for the design of resisting elements on local ductility demand and damage has been evaluated by parametric analysis. In particular, a comparison has been carried out between systems with equal design levels for all elements and systems with design levels dependent on the element location. For a given elastic behaviour and total capacity, the strength distributions in plan have been defined which minimize ductility demand and structural damage. Finally, based on these findings, responses from models designed according to several seismic codes have been compared. 相似文献
12.
The inelastic (design) spectra characterizing a seismic hazard are generally obtained by the scaling‐down of the elastic (design) spectra via a set of response modification factors. The component of these factors, which accounts for the ductility demand ratio, is known as the strength reduction factor (SRF), and the variation of this factor with initial period of the oscillator is called an SRF spectrum. This study considers scaling of the SRF spectrum in the case of an elasto‐plastic oscillator with strength and stiffness degradation characteristics. Two models are considered: one depending directly on the characterization of source and site parameters and the other depending on the normalized design spectrum characterization of the seismic hazard. The first model is the same as that proposed earlier by the second author, and is given in terms of earthquake magnitude, strong‐motion duration, predominant period, geological site conditions, ductility demand ratio, and ductility supply‐related parameter. The second model is a new model proposed here in terms of the normalized pseudo‐spectral acceleration values (to unit peak ground acceleration), ductility demand ratio and ductility supply‐related parameter. For each of these models, least‐square estimates of the coefficients are obtained through regression analyses of the data for 956 recorded accelerograms in western U.S.A. Parametric studies carried out with the help of these models confirm the dependence of SRFs on strong‐motion duration and earthquake magnitude besides predominant period and site conditions. It is also seen that degradation characteristics make a slight difference for high ductility demands and may lead to lower values of SRFs, unless the oscillators are very flexible. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
13.
This study presents ductility demand spectra for single degree of freedom (SDOF) systems under multiple near- and far-fault seismic ground motions. The main innovation has to do with the quantification of the seismic sequence effect directly into ductility demands, a phenomenon which has not been studied in the past. Due to lack of real seismic sequences records, this paper examines only artificial sequences, where they have been generated by a rational and random combination of real single events. A statistical investigation of more than 120 millions dynamic inelastic analyses is conducted to obtain expressions for the ductility demands, in terms of the period of vibration, the viscous damping, the post-yield stiffness and the force reduction factor. It is found that due to the seismic sequence effect, it is certainly insufficient to consider only the ‘design earthquake’, since this traditional hypothesis leads to underestimated ductility demands and therefore to underestimated structural damage. 相似文献
14.
弹塑性地震反应谱的长周期特性研究 总被引：3，自引：1，他引：3
在基于性能抗震设计中弹塑性反应谱在计算结构地震位移反应方面越来越受到重视。利用统计分析方法研究了等强度的延性需求谱和等延性的强度折减系数谱的长周期(至5 s)区段的特性,关注的重点是等位移准则和场地条件影响。给出了若干具有工程价值的结论:一是周期介于1.5Tg(地震动特征周期)和2.5 s之间的结构可近似认为等位移准则成立且与场地条件关系不大,这样确定的强度折减系数当位移延性系数小于等于4时结果将是偏于安全的;二是结构周期大于2.5 s后以硬土场地等延性强度折减系数谱或等强度延性需求谱代替软土场地谱求解系统强度需求或延性需求,将会得到偏于安全的结果。 相似文献
15.
Based on an asymmetric multistorey frame building model, this paper investigates the influence of a building's higher vibration modes on its inelastic torsional response and evaluates the adequacy of the provisions of current seismic building codes and the modal analysis procedure in accounting for increased ductility demand in frames situated at or near the stiff edge of such buildings. It is concluded that the influence of higher vibration modes on the response of the upper-storey columns of stiff-edge frames increases significantly with the building's fundamental uncoupled lateral period and the magnitude of the stiffness eccentricity. The application of the equivalent static torsional provisions of certain building codes may lead to non-conservative estimates of the peak ductility demand, particularly for structures with large stiffness eccentricity. In these cases, the critical elements are vulnerable to excessive additional ductility demand and, hence, may be subject to significantly more severe structural damage than in corresponding symmetric buildings. It is found that regularly asymmetric buildings excited well into the inelastic range may not be conservatively designed using linear elastic modal analysis theory. Particular caution is required when applying this method to the design of stiff-edge frame elements in highly asymmetric structures. 相似文献
16.
This paper summarizes the results of a comprehensive statistical study aimed at evaluating peak lateral inelastic displacement demands of structures with known lateral strength and stiffness built on soft soil site conditions. For that purpose, empirical information on inelastic displacement ratios which are defined as the ratio of peak lateral inelastic displacement demands to peak elastic displacement demands are investigated. Inelastic displacement ratios were computed from the response of single‐degree‐of‐freedom systems having 6 levels of relative lateral strength when subjected to 118 earthquake ground motions recorded on bay‐mud sites of the San Francisco Bay Area and on soft soil sites located in the former lake‐bed zone of Mexico City. Mean inelastic displacement ratios and their corresponding scatter are presented for both ground motion ensembles. The influence of period of vibration normalized by the predominant period of the ground motion, the level of lateral strength, earthquake magnitude, and distance to the source are evaluated and discussed. In addition, the effects of post‐yield stiffness and of stiffness and strength degradation on inelastic displacement ratios are also investigated. It is concluded that magnitude and distance to the source have negligible effects on constant‐strength inelastic displacement ratios. Results also indicate that weak and stiffness‐degrading structures in the short spectral region could experience inelastic displacement demands larger than those corresponding to non‐degrading structures. Finally, a simplified equation obtained using regression analyses aimed at estimating mean inelastic displacement ratios is proposed for assisting structural engineers in performance‐based assessment of structures built on soft soil sites. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
17.
This paper assesses the influence of cyclic and in‐cycle degradation on seismic drift demands in moment‐resisting steel frames (MRF) designed to Eurocode 8. The structural characteristics, ground motion frequency content, and level of inelasticity are the primary parameters considered. A set of single‐degree‐of‐freedom (SDOF) systems, subjected to varying levels of inelastic demands, is initially investigated followed by an extensive study on multi‐storey frames. The latter comprises a large number of incremental dynamic analyses (IDA) on 12 frames modelled with or without consideration of degradation effects. A suite of 56 far‐field ground motion records, appropriately scaled to simulate 4 levels of inelastic demand, is employed for the IDA. Characteristic results from a detailed parametric investigation show that maximum response in terms of global and inter‐storey drifts is notably affected by degradation phenomena, in addition to the earthquake frequency content and the scaled inelastic demands. Consistently, both SDOF and frame systems with fundamental periods shorter than the mean period of ground motion can experience higher lateral strength demands and seismic drifts than those of non‐degrading counterparts in the same period range. Also, degrading multi‐storey frames can exhibit distinctly different plastic mechanisms with concentration of drifts at lower levels. Importantly, degrading systems might reach a “near‐collapse” limit state at ductility demand levels comparable to or lower than the assumed design behaviour factor, a result with direct consequences on optimised design situations where over‐strength would be minimal. Finally, the implications of the findings with respect to design‐level limit states are discussed. 相似文献
18.
Uneven distribution of seismic demand in asymmetric-plan structures is a critical concern in earthquake-resistant design. Contemporary seismic design strategies that are based on linear elastic response, single load reduction factor, and uniform ductility demand throughout an asymmetric system generally lead to unsatisfactory performance in terms of realized ductilities and nonuniform damage distribution due to strong torsional coupling associated with asymmetric-plan systems. In many cases, actual nonlinear behavior of the structure displays significant deviation from what is estimated by a linear elastic, force-based seismic design approach. This study investigates the prediction of seismic demand distribution among structural members of a single-story, torsionally stiff asymmetric-plan system. The focus is on the effect of inherent unbalanced overstrength, resulting from current force-based design practices, on the seismic response of code-designed single-story asymmetric structures. The results obtained are utilized to compile unsymmetrical response spectra and uniform ductility spectra, which are proposed as assessment and preliminary design tools for estimating the seismic performance of multistory asymmetric structures. A simple design strategy is further suggested for improving the inelastic torsional performance of asymmetric systems. Providing additional strength to stiff edge members over their nominal design strength demands leads to a more balanced ductility distribution. Finally, seismic responses of several asymmetric case study structures designed with the aid of the proposed strategy are assessed for validating their improved performance. 相似文献
19.
剪切型结构的抗震强度折减系数研究 总被引：1，自引：0，他引：1
为了研究剪切型结构抗震强度需求的变化规律,本文基于单自由度体系的非线性时程分析,研究了不同场地条件下延性折减系数与位移延性系数和结构自振周期的关系;采用修正等效单自由度体系位移延性折减系数的方法,研究了剪切型多自由度体系的延性折减系数;以基于中国建筑抗震规范设计的代表不同抗震能力要求的RC框架结构为分析对象,通过静力弹塑性分析,研究了RC框架结构的体系超强能力。分析结果表明场地类别、位移延性水准和结构振动周期对单自由度体系的延性折减系数有显著的影响;多自由度体系的抗震延性折减系数明显比其相应的等效单自由度体系的抗震延性折减系数小;RC框架结构的超强系数一般随结构楼层数的增加而减小,随抗震设防烈度的增大而减小,内框架的超强系数比边框架的超强系数大。 相似文献