共查询到20条相似文献，搜索用时 78 毫秒
1.
中强地震活动区地震动衰减关系的确定 总被引：3，自引：0，他引：3
地震动衰减关系是影响地震安全性评价特别是地震区划结果的重要因素.我国现行的地震动衰减关系主要是依据6级以上地震的地面运动资料得到的,并没有考虑中强地震的衰减特性.为此,文中利用现有的烈度资料和其他可供参考的研究成果来建立我国中强地震活动区的地震动衰减关系.收集了我国华中、华南、东北等地区的51次地震的烈度等震线资料,运用单随机变量加权最小二乘回归法得到中强地震活动区烈度衰减关系.然后以美国西部地区为参考地区,运用缺乏地震动参数的地震动估计方法-地震对映射法得到中强地震活动区峰值加速度和有效峰值加速度衰减关系.最后,通过与我国强地震区和中强地震区已有的烈度衰减关系和地震动衰减关系的对比,验证了得出的我国中强地震活动区烈度衰减关系和地震动衰减关系的合理性. 相似文献
2.
利用《中国地震动参数区划图》采用的地震动参数衰减关系,以及《中国地震动参数区划图》中地震动峰值加速度和地震动加速度反应谱特征周期反推不同设防烈度和设计地震分组对应的震级和震中距,再根据《建筑抗震设计规范》中各设防水准的峰值加速度确定对应的震级和震中距,进而根据地震动强度包线参数与震级和震中距关系计算地震动强度包线参数的取值,为基于强度包线函数生成人工地震动提供参考,并讨论强度包线参数的取值规律：(1)随着设防烈度的提高,加速度时程曲线上升段持续时间t1和平稳段持续时间ts减小,下降段衰减指数c增大;(2)随着地震水准和设计地震分组的提高,加速度时程曲线上升段持续时间t1和平稳段持续时间ts增加,下降段衰减指数c减小;(3)在生成人工地震动时,除考虑峰值加速度和设计地震分组影响外,还需要考虑设防烈度影响。 相似文献
3.
河北及邻近地区地震动衰减关系的分析与确定 总被引：1，自引：0，他引：1
根据河北及邻近地区的地震烈度资料,美国西部地面水平加速度记录、地震动衰减关系和我国地面水平加速度记录,用最小二乘法及等震级的烈度地震动转换方法。确定了河北及邻近地区烈度衰减关系和不同场地地面运动水平加速度峰值衰减关系。这些研究成果可供河北及邻近地区进行地震危险性分析和抗震防灾规划时使用。 相似文献
4.
根据9.21台湾集集大地震过后南投县、台中县、台北县和苗栗县这四个主要受害地区的建筑物震害,参考不同的评定烈度标准综合确定出这四个地区的地震烈度,然后又计算出四地区的地震动峰值加速度、峰值速度、峰值谱加速度、峰值谱速度以及峰值谱位移的平均值。将这些均值分别与地震烈度进行基于最小二乘法的线性回归,发现这些地震动参数均值除峰值谱位移外都和烈度有很好的相关性,相关系数均在0.95以上,这说明研究评定的这四个地区的地震烈度是正确合理的,可以加以推广并应用于其它地震研究工作中。同时由于地震烈度是描述地震破坏后果的物理概念,地震动参数和烈度间的良好相关性也说明地震动参数和建筑物震害有很大的关联性,能够体现对结构的潜在破坏势。 相似文献
5.
6.
7.
山西地震动衰减关系的分析与确定 总被引：1，自引：0，他引：1
本文根据山西及邻近地区(简称山西地震带)的地震烈度资料,用最小二乘法分析确定了山西地区的烈度衰减关系。借用美国西部地区的地震动衰减资料,用转换的方法分析确定了山西地区的地震动参数衰减关系。这些研究结果可供山西重大工程场区进行地震危险性分析及城市地震小区划时应用。 相似文献
8.
2020年5月18日云南省巧家县发生M_S5.0地震,中国数字强震动台网的13个强震台站和昭通简易烈度计示范项目建设的43个烈度计台站,共接收168条强震动记录,经常规处理,绘制震区加速度峰值等值线图,并与云南地区常用地震动衰减关系进行对比,分析加速度峰值较大的几个台站频谱特性,计算地震动能量持时,讨论中小地震中高加速度峰值/低震害现象的成因,得到以下结论:(1) PGA等值线图形状较为平滑,其长轴呈NW—SE向展布;(2)云南地区常用地震动衰减关系预测值总体衰减趋势与观测值一致,但在近场(0—30 km)时,预测值基本偏小;(3)加速度峰值较大的几个台站记录主频集中在1—5 Hz;(4)小河镇台记录的能量持时较短,说明能量衰减较快,属脉冲型记录,不会对建筑物造成较大破坏。 相似文献
9.
汶川地震烈度衰减异常——与郯城、海原地震的比较 总被引：1，自引：0，他引：1
在地震安全性评价以及地震区划等研究工作中,选用合适的地震动参数(加速度、速度等)衰减关系是非常重要的.由于缺少强震记录,我国目前的地震动参数衰减关系一般采用胡聿贤和张敏政(1984)提出的转换方法获得,通过利用既有烈度资料又有强震记录的地区(参考地区)的烈度衰减关系和地震动参数衰减关系,经过转换得到只有烈度资料的研究地区的地震动参数衰减关系.上述工作需要使用适合各地区的地震烈度衰减关系来体现不同地区的地震活动与震害分布的地域性特点. 相似文献
10.
选用获得了加速度记录的2011年4月10日四川炉霍MS5.3及2011年8月11日新疆维吾尔自治区克孜勒尔自治州阿图什市与伽师县交界MS5.8地震,研究其快速生成震动图的偏差校正方法;通过台站实际观测值与借助经验性衰减关系估计值之间的残差分析,提出了利用台站数据对缺少台站地区借助经验性衰减关系估计值的对数偏差校正方法; 并比较了圆和椭圆衰减关系模型的对数残差及震动图的分布形态．结果表明, 适合于当地地震动衰减关系plusmn;3倍标准差的标准能够识别一些台站异常数据, 如炉霍MS5.3地震中炉霍地办强震台近场峰值加速度的高频脉冲引起的异常数据;对数偏差校正方法适合于地震动强度速报中缺少台站数据地区借助经验性衰减关系地震动参数估计值的系统偏差校正;圆衰减关系模型只能控制震动的程度,不能控制其分布形态．明确的地震震源机制、震源破裂过程、当地的地质构造背景及余震分布等信息有助于修正震动图的分布形态． 相似文献
11.
实际记录到的真实地震动在工程结构的抗震研究、分析和设计中往往作为一种施加到结构上使结构振动，直至破坏的地震荷载．如何合理选择真实的地震动记录作为研究结构地震反应的输入，一直是国内外抗震研究和设计中引人关注的重要问题．本文首先提出了最不利设计地震动的概念；然后在收集到的国内外5000余条被认为有重要意义的地震动记录基础上，利用综合估计地震动潜在破坏势的方法，对４种场地类型分别给出了长周期、短周期和中周期结构的国内外最不利设计地震动；最后通过几类不同结构的地震反应分析，初步验证了本文所确定的最不利设计地震动的可靠性和合理性． 相似文献
12.
How to select the adequate real strong earthquake ground motion for seismic analysis and design of trucures is an essential problem in earthquake engineering research and practice.In the paper the concept of the severest design ground motion is proposed and a method is developed for comparing the severity of the recorded strong ground motions.By using this method the severest earthquake ground motions are selected out as seismic inputs to the structures to be designed from a database that consists of more than five thousand significant strong ground moton records collected over the world.The selected severest ground motions are very likely to be able to drive the structures to their critical response and thereby result in the highest damage potential.It is noted that for different structures with diffferent predominant natural periods and at different sites where structures are located the severest design ground motions are usually different.Finally.two examples are illustrated to demonstrate the rationality of the concept and the reliability of the selected design motion. 相似文献
13.
Linear and non-linear responses of a two-story structural model excited by near-source fault-normal pulse and fault-parallel displacement are investigated. For the considered linear system, the multi-component differential-motion effects amplify the first-story drifts 3.0–4.0 times relative to the excitation by synchronous horizontal ground motion only. The contribution of horizontal differential ground motion to the total drift is about two thirds, and the contribution of vertical and rocking differential ground motions is about one third. For the considered nonlinear system, the effects of vertical and rocking differential ground motions become more significant for the second-story drifts. The horizontal differential ground motion amplifies the first-story drifts, but the simultaneous action of horizontal, vertical, and rocking differential ground motions can amplify the first- and second-story drifts by more than 2.0 times relative to the drifts computed for uniform horizontal ground motion only. 相似文献
14.
15.
Ground motion selection for simulation‐based seismic hazard and structural reliability assessment 
下载免费PDF全文
下载免费PDF全文 This paper examines four methods by which ground motions can be selected for dynamic seismic response analyses of engineered systems when the underlying seismic hazard is quantified via ground motion simulation rather than empirical ground motion prediction equations. Even with simulation‐based seismic hazard, a ground motion selection process is still required in order to extract a small number of time series from the much larger set developed as part of the hazard calculation. Four specific methods are presented for ground motion selection from simulation‐based seismic hazard analyses, and pros and cons of each are discussed via a simple and reproducible illustrative example. One of the four methods (method 1 ‘direct analysis’) provides a ‘benchmark’ result (i.e., using all simulated ground motions), enabling the consistency of the other three more efficient selection methods to be addressed. Method 2 (‘stratified sampling’) is a relatively simple way to achieve a significant reduction in the number of ground motions required through selecting subsets of ground motions binned based on an intensity measure, IM. Method 3 (‘simple multiple stripes’) has the benefit of being consistent with conventional seismic assessment practice using as‐recorded ground motions, but both methods 2 and 3 are strongly dependent on the efficiency of the conditioning IM to predict the seismic responses of interest. Method 4 (‘generalized conditional intensity measure‐based selection’) is consistent with ‘advanced’ selection methods used for as‐recorded ground motions and selects subsets of ground motions based on multiple IMs, thus overcoming this limitation in methods 2 and 3. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
16.
Rupture directivity effect on strong ground motion during the 12 May 2008 MW7.9 Wenchuan earthquake 下载免费PDF全文
下载免费PDF全文 We focus here on the rupture directivity effect on the spatial distribution and attenuation characteristics of near-field ground motions during the 2008 MW7.9 Wenchuan earthquake. We examine the difference between the observed ground motions in and opposite the rupture directions and compare them with Next Generation Attenuation-West2 (NGA-West2) ground motion prediction models. The isochrone directivity predictor is used to quantify the band-limited nature of the rupture directivity effect on strong ground motion. Our results show that the observed peak ground velocity (PGV) and spectral accelerations of periods of 1.0 s and longer are significantly amplified in the rupture direction, but de-amplified in the opposite direction affected by rupture directivity effect of this event. In contrast, the effect of rupture directivity on the observed peak ground acceleration (PGA) and periods of shorter than 1.0 s are relatively weak. The rupture directivity of this event shows clear period dependent and band limited characteristics with the strongest effect occurring around the period of 7.5 s. 相似文献
17.
18.
Site response to earthquake loading is one of the fundamental problems in geotechnical earthquake engineering. Most site response analyses assume vertically propagating shear waves in a horizontally layered soil–rock system and simply ignore the effect of site response to vertical earthquake motion, although actual ground motions are comprised of both horizontal and vertical components. In several recent earthquakes very strong vertical ground motions have been recorded, raising great concern over the potential effect of vertical motion on engineering structures. Being a step toward addressing this concern, this paper presents a simple and practical procedure for analysis of site response to both horizontal and vertical earthquake motions. The procedure involves the use of the dynamic stiffness matrix method and equivalent-linear approach, and is built in the modern MATLAB environment to take full advantages of the matrix operations in MATLAB. The input motions can be specified at the soil–bedrock interface or at a rock outcropping. A detailed assessment of the procedure is given, which shows that the procedure is able to produce acceptable predictions of both vertical and horizontal site responses. 相似文献
19.
估计和比较地震动潜在破坏势的综合评述 总被引：9，自引：3，他引：9
如何估计和比较地震动对结构的破坏作用，一直是国内外抗震研究中的一个至关重要的问题。本主要篇幅用于介绍这一领域迄今所取得的成果并作了简单的评述，并在此基础上，提出了一种可用来比较地震动潜在破坏势的综合评估法，提出该方法的目的并不在意去确定什么量更能代表地震动在潜在破坏势，而只是在考察现有的各种被认为能代表地震动的潜在破坏势的各种参数基础上，考虑采用什么方法才能更合理地判定和比较地震动的破坏势，为此本将通常作为地震动潜在破坏势的地震动参数分成两类：一类为直接由地震动本身得到的参数，另一类为地震动通过结构反应得到的参数，并分别对此进行了讨论和分析，在此基础上得出了一种在目前可认为是研究地震动潜在破坏势押送为合理的方法-地震动潜在破坏势综合评价法。 相似文献
20.
Many studies have focused on horizontal ground motion, resulting in many coherency functions for horizontal ground motion while neglecting related problems arising from vertical ground motion. However, seismic events have demonstrated that the vertical components of ground motion sometimes govern the ultimate failure of structures. In this paper, a vertical coherency function model of spatial ground motion is proposed based on the Hao model and SMART 1 array records, and the validity of the model is demonstrated. The vertical coherency function model of spatial ground motion is also compared with the horizontal coherency function model, indicating that neither model exhibits isotropic characteristics. The value of the vertical coherency function has little correlation with that of the horizontal coherency function. However, the coherence of the vertical ground motion between a pair of stations decreases with their projection distance and the frequency of the ground motion. When the projection distance in the wave direction is greater than 800 meters, the coherency between the two points can be neglected. 相似文献