首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 26 毫秒
1.
The heterogeneous distribution of fluids in patchy-saturated rocks generates significant velocity dispersion and attenuation of seismic waves. The mesoscopic Biot–Rayleigh theory is used to investigate the relations between wave responses and reservoir fluids. Multiscale theoretical modeling of rock physics is performed for gas/water saturated carbonate reservoirs. Comparisons with laboratory measurements, log and seismic data validate the rock physics template. Using post-stack and pre-stack seismic inversion, direct estimates of rock porosity and gas saturation of reservoirs are obtained, which are in good agreement with oil production tests of the wells.  相似文献   

2.
We measured the extensional‐mode attenuation and Young's modulus in a porous sample made of sintered borosilicate glass at microseismic to seismic frequencies (0.05–50 Hz) using the forced oscillation method. Partial saturation was achieved by water imbibition, varying the water saturation from an initial dry state up to ～99%, and by gas exsolution from an initially fully water‐saturated state down to ～99%. During forced oscillations of the sample effective stresses up to 10 MPa were applied. We observe frequency‐dependent attenuation, with a peak at 1–5 Hz, for ～99% water saturation achieved both by imbibition and by gas exsolution. The magnitude of this attenuation peak is consistently reduced with increasing fluid pressure and is largely insensitive to changes in effective stress. Similar observations have recently been attributed to wave‐induced gas exsolution–dissolution. At full water saturation, the left‐hand side of an attenuation curve, with a peak beyond the highest measured frequency, is observed at 3 MPa effective stress, while at 10 MPa effective stress the measured attenuation is negligible. This observation is consistent with wave‐induced fluid flow associated with mesoscopic compressibility contrasts in the sample's frame. These variations in compressibility could be due to fractures and/or compaction bands that formed between separate sets of forced‐oscillation experiments in response to the applied stresses. The agreement of the measured frequency‐dependent attenuation and Young's modulus with the Kramers–Kronig relations and additional data analyses indicate the good quality of the measurements. Our observations point to the complex interplay between structural and fluid heterogeneities on the measured seismic attenuation and they illustrate how these heterogeneities can facilitate the dominance of one attenuation mechanism over another.  相似文献   

3.
砾岩储层地震波传播方程:三重孔隙结构模型   总被引：1，自引：1，他引：0       下载免费PDF全文
针对砾岩储层的砂、砾、泥三重孔隙结构特征,本文分析砾岩孔隙区域、砂岩孔隙区域以及泥岩孔隙区域相互之间的孔隙流体流动机制,将静态的砾岩骨架本构方程与动态的孔隙流体运动方程联立,提出了复杂砾岩储层的弹性波传播理论方程.采用实测砾岩储层参数,在算例中与双重孔隙介质理论进行对比分析,验证了本文理论方程的合理性;基于三重孔隙介质模型,分析不同储层环境下纵波的传播特征,结果显示:随流体黏滞系数增大,在衰减-频率轴坐标系中,砾与砂、砂与泥孔隙区域间局域流导致的两个衰减峰向低频端移动,而Biot全局流导致的衰减峰向高频端移动;嵌入体尺寸及背景相介质渗透率的变化,主要影响纵波速度频散曲线沿频率轴左、右平移,不影响波速低频、高频极限幅值;嵌入体含量及孔隙度的变化改变了岩石干骨架的弹性、密度参数,不仅影响速度频散曲线沿频率轴平移,而且影响其上、下限幅值;砾包砂包泥三重孔隙介质模型所预测的衰减曲线中,低频段"第一个衰减峰"主要由砾岩孔隙区域与砂岩孔隙区域之间的局域流导致,中间频段"第二个衰减峰"主要由砂岩孔隙区域与泥岩孔隙区域之间的局域流导致,超声频段"第三个衰减峰"由Biot全局流导致.对慢纵波传播特征的分析显示,砂岩骨架(局部孔隙度较大)内部的宏观孔隙流体流动造成的耗散明显强于砾岩与泥岩骨架.  相似文献   

4.
In fractured reservoirs, seismic wave velocity and amplitude depend on frequency and incidence angle. Frequency dependence is believed to be principally caused by the wave‐induced flow of pore fluid at the mesoscopic scale. In recent years, two particular phenomena, i.e., patchy saturation and flow between fractures and pores, have been identified as significant mechanisms of wave‐induced flow. However, these two phenomena are studied separately. Recently, a unified model has been proposed for a porous rock with a set of aligned fractures, with pores and fractures filled with two different fluids. Existing models treat waves propagating perpendicular to the fractures. In this paper, we extend the model to all propagation angles by assuming that the flow direction is perpendicular to the layering plane and is independent of the loading direction. We first consider the limiting cases through poroelastic Backus averaging, and then we obtain the five complex and frequency‐dependent stiffness values of the equivalent transversely isotropic medium as a function of the frequency. The numerical results show that, when the bulk modulus of the fracture‐filling fluid is relatively large, the dispersion and attenuation of P‐waves are mainly caused by fractures, and the values decrease as angles increase, almost vanishing when the incidence angle is 90° (propagation parallel to the fracture plane). While the bulk modulus of fluid in fractures is much smaller than that of matrix pores, the attenuation due to the “partial saturation” mechanism makes the fluid flow from pores into fractures, which is almost independent of the incidence angle.  相似文献   

5.
We derived the velocity and attenuation of a generalized Stoneley wave being a symmetric trapped mode of a layer filled with a Newtonian fluid and embedded into either a poroelastic or a purely elastic rock. The dispersion relation corresponding to a linearized Navier–Stokes equation in a fracture coupling to either Biot or elasticity equations in the rock via proper boundary conditions was rigorously derived. A cubic equation for wavenumber was found that provides a rather precise analytical approximation of the full dispersion relation, in the frequency range of 10?3 Hz to 103 Hz and for layer width of less than 10 cm and fluid viscosity below 0.1 Pa· s [100 cP]. We compared our results to earlier results addressing viscous fluid in either porous rocks with a rigid matrix or in a purely elastic rock, and our formulae are found to better match the numerical solution, especially regarding attenuation. The computed attenuation was used to demonstrate detectability of fracture tip reflections at wellbore, for a range of fracture lengths and apertures, pulse frequencies, and fluid viscosity.  相似文献   

6.
This paper describes the measurements of the acoustic and petrophysical properties of two suites of low‐shale sandstone samples from North Sea hydrocarbon reservoirs, under simulated reservoir conditions. The acoustic velocities and quality factors of the samples, saturated with different pore fluids (brine, dead oil and kerosene), were measured at a frequency of about 0.8 MHz and over a range of pressures from 5 MPa to 40 MPa. The compressional‐wave velocity is strongly correlated with the shear‐wave velocity in this suite of rocks. The ratio VP/VS varies significantly with change of both pore‐fluid type and differential pressure, confirming the usefulness of this parameter for seismic monitoring of producing reservoirs. The results of quality factor measurements were compared with predictions from Biot‐flow and squirt‐flow loss mechanisms. The results suggested that the dominating loss in these samples is due to squirt‐flow of fluid between the pores of various geometries. The contribution of the Biot‐flow loss mechanism to the total loss is negligible. The compressional‐wave quality factor was shown to be inversely correlated with rock permeability, suggesting the possibility of using attenuation as a permeability indicator tool in low‐shale, high‐porosity sandstone reservoirs.  相似文献   

7.
Wave‐induced fluid flow plays an important role in affecting the seismic dispersion and attenuation of fractured porous rocks. While numerous theoretical models have been proposed for the seismic dispersion and attenuation in fractured porous rocks, most of them neglect the wave‐induced fluid flow resulting from the background anisotropy (e.g. the interlayer fluid flow between different layers) that can be normal in real reservoirs. Here, according to the theories of poroelasticity, we present an approach to study the frequency‐dependent seismic properties of more realistic and complicated rocks, i.e. horizontally and periodically layered porous rock with horizontal and randomly orienting fractures, respectively, distributed in one of the two periodical layers. The approach accounts for the dual effects of the wave‐induced fluid flow between the fractures and the background pores and between different layers (the interlayer fluid flow). Because C33 (i.e., the modulus of the normally incident P‐wave) is directly related to the P‐wave velocity widely measured in the seismic exploration, and its comprehensive dispersion and attenuation are found to be most significant, we study mainly the effects of fracture properties and the stiffness contrast between the different layers on the seismic dispersion and attenuation of C33. The results show that the increasing stiffness contrast enhances the interlayer fluid flow of the layered porous rocks with both horizontal and randomly orienting fractures and weakens the wave‐induced fluid flow between the fractures and the background pores, especially for the layered porous rock with horizontal fractures. The modelling results also demonstrate that for the considered rock construction, the increasing fracture density reduces the interlayer fluid flow while improves the dispersion and attenuation in the fracture‐relevant frequency band. Increasing fracture aspect ratio is found to reduce the dispersion and attenuation in the fracture‐relevant frequency band only, especially for the layered porous rock with horizontal fractures.  相似文献   

8.
Partially saturated reservoirs are one of the major sources of seismic wave attenuation, modulus defect and velocity dispersion in real seismic data. The main attenuation and dispersion phenomenon is wave induced fluid flow due to the heterogeneity in pore fluids or porous rock. The identification of pore fluid type, saturation and distribution pattern within the pore space is of great significance as several seismic and petrophysical properties of porous rocks are largely affected by fluid type, saturation and fluid distribution pattern. Based on Gassmann-Wood and Gassmann- Hill rock physics models modulus defect, velocity dispersion and attenuation in Jurassic siliclastic partially-saturated rocks are studied. For this purpose two saturation patterns - uniform and patchy - are considered within the pore spaces in two frequency regimes i.e., lower frequency and higher frequency. The results reveal that at low enough frequency where saturation of liquid and gas is uniform, the seismic velocity and bulk modulus are lower than at higher frequency where saturation of fluid mixture is in the form of patches. The velocity dispersion and attenuation is also modeled at different levels of gas saturation. It is found that the maximum attenuation and velocity dispersion is at low gas saturation. Therefore, the dispersion and attenuation can provide a potential way to predict gas saturation and can be used as a property to differentiate low from high gas saturation.  相似文献   

9.
In exploration geophysics, the efforts to extract subsurface information from wave characteristics exceedingly depend on the construction of suitable rock physics model. Analysis of different rock physics models reveals that the strength and magnitude of attenuation and dispersion of propagating wave exceedingly depend on wave-induced fluid flow at multiple scales. In current work, a comprehensive analysis of wave attenuation and velocity dispersion is carried out at broad frequency range. Our methodology is based on Biot's poroelastic relations, by which variations in wave characteristics associated with wave-induced fluid flow due to the coexistence of three fluid phases in the pore volume is estimated. In contrast to the results of previous research, our results indicate the occurrence of two-time pore pressure relaxation phenomenon at the interface between fluids of disparate nature, that is, different bulk modulus, viscosity and density. Also, the obtained results are compatible with numerical results for the same 1D model which are accounted using Biot's poroelastic and quasi-static equation in frequency domain. Moreover, the effects of change in saturation of three-phase fluids were also computed which is the key task for geophysicist. The outcomes of our research reveal that pore pressure relaxation phenomenon significantly depends on the saturation of distinct fluids and the order of saturating fluids. It is also concluded that the change in the saturation of three-phase fluid significantly influences the characteristics of the seismic wave. The analysis of obtained results indicates that our proposed approach is a useful tool for quantification, identification and discrimination of different fluid phases. Moreover, our proposed approach improves the accuracy to predict dispersive behaviour of propagating wave at sub-seismic and seismic frequencies.  相似文献   

10.
In this paper two causal models that approximate the nearly frequency‐independent cyclic behaviour of soils are analysed in detail. The study was motivated by the need to conduct time‐domain viscoelastic analysis on soil structures without adopting the ad hoc assumption of Rayleigh damping. First, the causal hysteretic model is introduced in which its imaginary part is frequency independent the same way that is the imaginary part of the popular non‐causal constant hysteretic model. The adoption of an imaginary part that is frequency independent even at the zero‐frequency limit, in conjunction with the condition that the proposed model should be causal, yields a real part that is frequency dependent and singular at zero frequency. The paper shows that the causal hysteretic model, although pathological at the static limit, is the mathematical connection between the non‐causal constant hysteretic model and the physically realizable Biot model. The mathematical structure of the two causal models is examined and it is shown that the causal hysteretic model is precisely the high‐frequency limit of the Biot model. Although both models have a closed‐form time‐domain representation, only the Biot model is suitable for a time‐domain viscoelastic analysis with commercially available computer software. The paper demonstrates that the simplest, causal and physically realizable linear hysteretic model that can approximate the cyclic behaviour of soil is the Biot model. The proposed study elucidates how the dynamic analysis of soil structures can be conducted rigorously in terms of the viscoelastic properties of the soil material and not with the ad hoc Rayleigh damping approach which occasionally has been criticized that tends to overdamp the higher vibration modes. The study concludes that under pulse‐type motions the Rayleigh damping approximation tends to overestimate displacements because of the inappropriate viscous type of dissipation that is imposed. Under longer motions that induce several cycles, the concept of equivalent viscous damping is more appropriate and the Rayleigh damping approximation results to a response that is comparable to the response computed with a rigorous time‐domain viscoelastic finite element analysis. Copyright © 2000 John Wiley & Sons, Ltd.  相似文献   

11.
含流体孔隙介质中面波的传播特性及应用   总被引：2，自引：2，他引：0       下载免费PDF全文
基于单相介质中地震波理论的高频面波法已广泛应用于求取浅地表S波的速度.然而水文地质条件表明,普遍的浅地表地球介质富含孔隙.孔隙中充填的流体会显著地影响面波在浅地表的传播,进而造成频散和衰减的变化.本文研究了地震勘探频段内针对含流体孔隙介质边界条件的面波的传播特性.孔隙流体在自由表面存在完全疏通、完全闭合以及部分疏通的情况.孔隙单一流体饱和时,任何流体边界条件下存在R1模式波,与弹性介质中的Rayleigh波类似,相速度稍小于S波并在地震记录中显示强振幅.由于介质的内在衰减,R1在均匀半空间中也存在频散,相速度和衰减在不同流体边界下存在差异.Biot固流耦合系数(孔隙流体黏滞度与骨架渗透率之比)控制频散的特征频率,高耦合系数会在地震勘探频带内明显消除这种差异.介质的迂曲度等其他物性参数对不同流体边界下的R1波的影响也有不同的敏感度.完全闭合和部分疏通流体边界下存在R2模式波,相速度略低于慢P波.在多数条件下,如慢P波在时频响应中难以观察到.但是在耦合系数较低时会显现,一定条件下甚至会以非物理波形式接收R1波的辐射,显示强振幅.浅表风化层低速带存在,震源激发时的运动会显著影响面波的传播.对于接收点径向运动会造成面波的Doppler频移,横向运动会造成面波的时频畸变.孔隙存在多相流体时,中观尺度下不均匀斑块饱和能很好地解释体波在地震频带内的衰减.快P波受到斑块饱和显著影响,R1波与快P波有更明显关联,与完全饱和模型中不同,也更易于等效模型建立.频散特征频率受孔隙空间不同流体成分比例变化的控制,为面波方法探测浅地表流体分布与迁移提供可能性.通常情况孔隙介质频散特征频率较高,标准线性黏弹性固体可以在相对低频的地震勘探频带内等效表征孔隙介质中R1波的传播特征,特别在时域,可在面波成像反演建模中应用.  相似文献   

12.
We obtain the wave velocities and quality factors of clay‐bearing sandstones as a function of pore pressure, frequency and partial saturation. The model is based on a Biot‐type three‐phase theory that considers the coexistence of two solids (sand grains and clay particles) and a fluid mixture. Additional attenuation is described with the constant‐Q model and viscodynamic functions to model the high‐frequency behaviour. We apply a uniform gas/fluid mixing law that satisfies the Wood and Voigt averages at low and high frequencies, respectively. Pressure effects are accounted for by using an effective stress law. By fitting a permeability model of the Kozeny– Carman type to core data, the model is able to predict wave velocity and attenuation from seismic to ultrasonic frequencies, including the effects of partial saturation. Testing of the model with laboratory data shows good agreement between predictions and measurements.  相似文献   

13.
Different theoretical and laboratory studies on the propagation of elastic waves in layered hydrocarbon reservoir have shown characteristic velocity dispersion and attenuation of seismic waves. The wave‐induced fluid flow between mesoscopic‐scale heterogeneities (larger than the pore size but smaller than the predominant wavelengths) is the most important cause of attenuation for frequencies below 1 kHz. Most studies on mesoscopic wave‐induced fluid flow in the seismic frequency band are based on the representative elementary volume, which does not consider interaction of fluid flow due to the symmetrical structure of representative elementary volume. However, in strongly heterogeneous media with unsymmetrical structures, different courses of wave‐induced fluid flow may lead to the interaction of the fluid flux in the seismic band; this has not yet been explored. This paper analyses the interaction of different courses of wave‐induced fluid flow in layered porous media. We apply a one‐dimensional finite‐element numerical creep test based on Biot's theory of consolidation to obtain the fluid flux in the frequency domain. The characteristic frequency of the fluid flux and the strain rate tensor are introduced to characterise the interaction of different courses of fluid flux. We also compare the behaviours of characteristic frequencies and the strain rate tensor on two scales: the local scale and the global scale. It is shown that, at the local scale, the interaction between different courses of fluid flux is a dynamic process, and the weak fluid flux and corresponding characteristic frequencies contain detailed information about the interaction of the fluid flux. At the global scale, the averaged strain rate tensor can facilitate the identification of the interaction degree of the fluid flux for the porous medium with a random distribution of mesoscopic heterogeneities, and the characteristic frequency of the fluid flux is potentially related to that of the peak attenuation. The results are helpful for the prediction of the distribution of oil–gas patches based on the statistical properties of phase velocities and attenuation in layered porous media with random disorder.  相似文献   

14.
Average elastic properties of a fluid‐saturated fractured rock are discussed in association with the extremely slow and dispersive Krauklis wave propagation within individual fractures. The presence of the Krauklis wave increases P‐wave velocity dispersion and attenuation with decreasing frequency. Different laws (exponential, power, fractal, and gamma laws) of distribution of the fracture length within the rock show more velocity dispersion and attenuation of the P‐wave for greater fracture density, particularly at low seismic frequencies. The results exhibit a remarkable difference in the P‐wave reflection coefficient for frequency and angular dependency from the fractured layer in comparison with the homogeneous layer. The biggest variation in behaviour of the reflection coefficient versus incident angle is observed at low seismic frequencies. The proposed approach and results of calculations allow an interpretation of abnormal velocity dispersion, high attenuation, and special behaviour of reflection coefficients versus frequency and angle of incidence as the indicators of fractures.  相似文献   

15.
介观尺度孔隙流体流动是地震频段岩石表现出较强速度频散与衰减的主要作用.利用周期性层状孔隙介质模型,基于准静态孔弹性理论给出了模型中孔隙压力、孔隙流体相对运动速度以及固体骨架位移等物理量的数学解析表达式,同时利用Biot理论将其扩展至全频段条件下,克服了传统White模型中介质分界面处流体压力不连续的假设. 在此基础上对准静态与全频段下模型介质中孔隙压力、孔隙流体相对运动速度变化形式及其对弹性波传播特征的影响进行了讨论,为更有效理解介观尺度下流体流动耗散和频散机制提供物理依据.研究结果表明,低频条件下快纵波孔压在介质层内近于定值,慢纵波通过流体扩散改变总孔隙压力, 随频率的增加慢波所形成的流体扩散作用逐渐减弱致使介质中总孔压逐渐接近于快纵波孔压,在较高频率下孔压与应力的二次耦合作用使总孔压超过快纵波孔压.介质中孔隙流体相对运动速度与慢纵波形成的流体相对运动速度变化形式一致;随频率的增加孔隙流体逐渐从排水的弛豫状态过渡到非弛豫状态,其纵波速度-含水饱和度变化形式也从符合孔隙流体均匀分布模式过渡到斑块分布模式,同时介质在不同含水饱和度下的衰减峰值与慢纵波所形成的孔隙流体相对流动速度具有明显的相关性.  相似文献   

16.
二氧化碳地质封存是减少温室气体排放和减缓温室效应的重要手段.二氧化碳封存的一个重要组成部分是地震监测,即用地震的方法监测封存后的二氧化碳的分布变化.为了实现这个目标,需要建立储层参数与地震性质之间的关系(岩石物理模型)和从地震监测数据中反演获得储层流体的饱和度等参数.首先,本文以Biot理论为基础,结合多相流模型研究了多个物理参数(孔隙度、二氧化碳饱和度、温度和压力等)对同时含有二氧化碳和水的孔隙介质的波速和衰减等属性的影响.结果表明:孔隙度和二氧化碳饱和度对岩石的频散和衰减属性影响强烈,而温度和压力通过孔隙流体性质对岩石的波速产生影响.然后,本文基于含多相流的Biot理论,应用抗干扰能力强、且具有更好的局部搜索能力和抗早熟能力的自适应杂交遗传算法对实际数据进行了反演研究.对岩心实验数据的反演研究表明了算法的有效性,而且表明含多相流的Biot理论能够很好地解释水和二氧化碳饱和岩石的波速特征.最后,我们将自适应杂交遗传算法应用于实际封存项目的地震监测数据,获得了封存后不同时期的二氧化碳饱和度,达到了用地震方法监测二氧化碳分布的目的.  相似文献   

17.
A model of wave propagation in fluid-saturated porous media is developed where the principal fluid/solid interaction mode affecting the propagation of the acoustic wave results from the conjunction of the Biot and the Squirt flow mechanism. The difference between the original Biot/Squirt (BISQ) flow theory and the new theory, which we call the reformulated BISQ, is that the average fluid pressure term appearing in the dynamic equation for a two component solid/fluid continuum is independent of squirt flow length. P-velocity and attenuation relate to measurable rock physical parameters: the Biot's poroelastic constants, porosity, permeability, pore fluid compressibility and viscosity. Modelling shows that velocity and attenuation dispersion obtained using the reformulated BISQ theory are of the same order of magnitude as those obtained using the original BISQ theory. Investigation on permeability effect on velocity and attenuation dispersion indicate that the transition zone in velocity and attenuation peak, occurring both at the relaxation frequency, shifts toward high frequency when permeability decreases. This behaviour agrees with Biot's theory prediction.  相似文献   

18.
In the free state, Rayleigh waves are assumed to travel in the form of planar wavefronts. Under such an assumption, the propagation behaviour of the modes of Rayleigh waves in layered half‐spaces is only frequency dependent. The frequency behaviour, which is often termed as dispersion, is determined by the shear wave velocity profile of layered soils within the depth related to wavelength (or frequency). According to this characteristic, the shear wave velocity profile can be back‐analysed from the dispersion. The technique is widely used in the surface wave testing. However, the wavefronts of Rayleigh waves activated by the surface sources are non‐planar. The geometric discrepancy could result in Rayleigh waves manifesting distance‐dependent behaviour, which is referred to as spatial behaviour in this paper. Conventional analysis ignoring this spatial behaviour could introduce unexpected errors. In order to take the effects of sources on the propagation behaviour into account, a new mathematical model is established for Rayleigh waves in layered elastic media under vertical disc‐like surface sources using the thin‐layer method. The spatial behaviour of the activated modes and the apparent phase velocity, which is the propagation velocity of Rayleigh waves superposed by the multiple modes, are then analysed. Aspects of the spatial behaviour investigated in this paper include the equilibrium path, the particle orbit, and the geometric attenuation of the activated Rayleigh waves. The results presented in this paper can provide some guidelines for developing new inverse mathematical models and algorithms.  相似文献   

19.
Predicting the shear‐wave (S‐wave) velocity is important in seismic modelling, amplitude analysis with offset, and other exploration and engineering applications. Under the low‐frequency approximation, the classical Biot–Gassmann theory relates the Biot coefficient to the bulk modulus of water‐saturated sediments. If the Biot coefficient under in situ conditions can be estimated, the shear modulus or the S‐wave velocity can be calculated. The Biot coefficient derived from the compressional‐wave (P‐wave) velocity of water‐saturated sediments often differs from and is less than that estimated from the S‐wave velocity, owing to the interactions between the pore fluid and the grain contacts. By correcting the Biot coefficients derived from P‐wave velocities of water‐saturated sediments measured at various differential pressures, an accurate method of predicting S‐wave velocities is proposed. Numerical results indicate that the predicted S‐wave velocities for consolidated and unconsolidated sediments agree well with measured velocities.  相似文献   

20.
P‐ and S‐wave velocity and attenuation coefficients (accurate to ±0.3% and ±0.2 dB/cm, respectively) were measured in synthetic porous rocks with aligned, penny‐shaped fractures using the laboratory ultrasonic pulse‐echo method. Shear‐wave splitting was observed by rotating the S‐wave transducer and noting the maximum and minimum velocities relative to the fracture direction. A block of synthetic porous rock of fracture density 0.0201 ± 0.0068 and fracture size 3.6 ± 0.38 mm (measured from image analysis of X‐ray CT scans) was sub‐sampled into three 20–30 mm long, 50 mm diameter core plugs oriented at 0°, 45° and 90° to the fracture normal (transversely isotropic symmetry axis). Full waveform data were collected over the frequency range 500–1000 kHz for both water and glycerin saturated cores to observe the effect of pore fluid viscosity at 1 cP and 100 cP, respectively. The shear‐wave splitting observed in the 90° core was 2.15 ± 0.02% for water saturated and 2.39 ± 0.02% for glycerin saturated, in agreement with the theory that suggests that the percentage splitting should be 100 times the fracture density and independent of the saturating fluid. In the 45° core, by contrast, splitting was 0.00 ± 0.02% for water saturation and ?0.77 ± 0.02% for glycerin saturation. This dependence on fracture orientation and pore fluid viscosity is consistent with the poro‐visco‐elastic theory for aligned, meso‐scale fractures in porous rocks. The results suggest the possible use of shear‐ or converted‐wave data to discriminate between fluids on the basis of viscosity variations.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号