共查询到20条相似文献，搜索用时 31 毫秒
1.
Most field tests are carried out using working piles for verification purposes in China, and loading tests are terminated before achieving true pile capacity. In this work, two full-scale destructive loading tests on tension piles instrumented with strain gauges were conducted to capture true pile capacity. The load-displacement response, load transfer, and threshold of the pile-soil relative displacement for fully mobilizing skin resistance in the uplift case were discussed. It was found that the shaft resistance degradation is observed to be along the pile depth with a reduction factor of 0.905 to 0.931, and the thresholds of pile-soil relative displacement for fully mobilizing skin resistance of the tension pile in different soils are found to be in the range 0.67% to 1.34% of the pile diameter. Based on the field test results, a simple softening model was proposed to describe the degradation behavior of skin friction along the pile-soil interface. Further study was conducted to assess the influence of the threshold of pile-soil relative displacement for fully mobilizing skin friction and the reduction factor on the skin friction. As to the analysis of the response of single pile subjected to tension load, a highly effective iterative computer program was developed using the proposed skin friction softening model. Comparisons of the load-settlement response for the well-instrumented tests were given to demonstrate the effectiveness and accuracy of the proposed simple method. 相似文献
2.
In this article, two full-scale pile loading tests were conducted to observe the field performance of the super-long bored piles, and a simplified approach for nonlinear analysis of the load-displacement behavior of a single pile was presented. The field tests on piles indicates that, under the maximum test load, more than 70% of the pile top settlement is caused by the compression of pile shaft. For practical purposes, the pile top settlement can be reduced through improving the pile shaft strength. When the load reaches the maximum test load, the proportion of the load carried by the pile tip is approximately 30%. The super-long pile is functioning as an end-bearing friction pile. The skin friction at shallow depth is fully mobilized and decreases from a peak value with increasing load. However, the skin friction of deeper soil is not fully developed due to less relative displacement. Furthermore, a BoxLucas1 model is used to capture the relationship between unit skin friction and pile-soil relative displacement, whereas a hyperbolic model is used to describe the relationship between toe stress and pile base displacement. Based on the BoxLucas1 model and the hyperbolic model, a load transfer method is used to clarify the response of a single pile, and a computational flow chart is developed. The efficiency and accuracy of the present method is verified using the field tests on piles. The proposed simple analytical approach is economical and efficient, resulting in savings in time and cost. 相似文献
3.
A research on super-long piles has been primarily based on cast-in-place bored piles. In this article, field tests associated with selected measuring technologies were conducted on two super-long steel pipe piles in offshore areas to investigate the behaviors and performance of super-long steel pipe piles. The strain along the pile shaft was monitored by adopting the Brillouin optical time domain reflection and fiber Bragg grating techniques. Static load tests were also conducted on two test piles to determine the bearing capacities. In addition, the axial forces, relative displacements between piles and soils and pile shaft resistances were calculated based on the measured strain. According to the results of the static load tests, the ultimate bearing capacities of the two test piles are greater than 15,000 and 15,500 kN. Both of these values meet the design requirements. In addition, the two test piles can be treated as pure friction piles, and the load transfer mechanism and relationships between the pile shafts and relative displacements are also discussed. Finally, recommendations for practical engineering and significant conclusions are presented. 相似文献
4.
The behavior of single piles subjected to negative skin friction in soft soil was conducted by analyzing the results from full-scale long-term field measurements and three-dimensional (3D) numerical analyses. A skin friction coefficient (α and β coefficients) of the instrumented piles is back-calculated at different degrees of consolidation (U) of soft marine clay. Back-calculated β-values ranged from 0.15 to 0.35 for clay, and from 0.30 to 0.55 for sand, respectively. In addition, back-calculated α-values ranged from 0.1 to 0.3 for coated pile, and from 0.2 to 0.8 for uncoated pile when undrained shear strength of the soft clay was about 30–60 kPa, respectively. Moreover, this study describes behavior of a pile based on full-coupled 3D finite element (FE) analysis. The appropriate parametric studies needed for verifying the pile-soil interaction with consolidation are presented in this paper. Compared to the results from the measurements, it is shown that the computed results are capable of predicting the pile-soil behavior under consolidation. The major parameters that influence the pile behavior are discussed for different soil-pile conditions. 相似文献
5.
Mohammed Y. Fattah Bushra S. Zbar Faris S. Mustafa 《Marine Georesources & Geotechnology》2017,35(8):1111-1120
In this study, the dynamic response of pile foundation in dry sandy soil excited by two opposite rotary machines was considered experimentally. A small scale physical model was manufactured to accomplish the experimental work in the laboratory. The physical model consists of two small motors supplied with eccentric mass (0.012?kg) and eccentric distance (20?mm) representing the two opposite rotary machines, an aluminum shaft as the pile, and a steel plate a pile cap. The experimental work was achieved taking the following parameters into considerations: pile embedment depth ratio (L/d, where L is the pile length and d is its diameter) and operating frequency of the rotary machines. All tests were conducted in medium dense fine sandy soil with 60% relative density. Twelve tests were performed to measure the change in load transferred through the pile’s tip to the underlying soil. To predict precisely the dynamic load that will be induced from the rotary machines, a mini load cell with a capacity of 100?kg was mounted between the aluminum plate (the machine base) and the steel plate (pile cap). The results revealed that, before machine operation, the pile tip load was approximately equal to the static load (machine and pile cap), whereas during machines’ operation, the pile tip load decreased for all embedment depth ratios and operating frequencies. This reduction was due to the action of skin friction that was mobilized along the pile during operation, and as a result the factor of safety against pile bearing failure increases. For all operating frequencies and pile lengths, the factor of safety against bearing failure increased during machines’ operation, where the pile tip load became less than its value before starting operation. During operation, the skin friction resistance mobilized along pile length led to decrease the bearing load. 相似文献
6.
This study has evaluated the vertical bearing capacity by conducting static load tests for noise-free and vibration-free screw pretensioned spun high-strength concrete (PHC) piles installed using two different methods (end-squirting shoe and pre-boring methods). Vertical bearing capacity differences seem to occur due to the displacement of soils near the external circumference of a pile, depending on the installation method. A method by which to evaluate the bearing capacity of screw concrete piles is suggested by considering the equations that already have been used to calculate the bearing capacity of piles. Based on static load tests and analysis, the pile installed using the end-squirting shoe method was assumed to be a bored pile and it was reasonable to use the equation proposed by the Japanese Geotechnical Society. At the same time, the pile installed using the pre-boring method was deemed a low soil displacement pile and so it was reasonable to apply the equations proposed for calculating the bearing capacity of the driven pile suggested by the Architectural Institute of Japan. 相似文献
7.
采用有限元软件ABAQUS建立了海上风电单桩基础与土相互作用数值计算模型,将波浪、洋流及风荷载等效成双向对称循环荷载,研究了水平循环荷载作用下不同因素对桩身水平位移、剪力和弯矩的影响规律。研究表明,随着循环荷载比的增加,桩身位移零点和桩身剪力反弯点沿埋深逐渐下移,桩身弯矩最大值点位于浅层土体;不同荷载频率时桩身位移在零点以上变化较大,桩身弯矩随着频率的增加逐渐增大;单向循环荷载作用下桩身位移最大,双向对称循环荷载作用下桩身位移最小;壁厚较小时对桩身水平位移影响较大;在位移零点之上范围内可以考虑设计"上厚下薄"的钢管桩,以减小桩身水平位移;不同桩壁厚时桩身剪力曲线在埋深约6D处出现交点,且泥面处桩身弯矩变化不明显。 相似文献
8.
The scour hole around a pile will reduce the capacity of a laterally loaded pile. The strain wedge model is capable to derive a p–y curve for the analysis of a lateral loaded pile on a nonlinear Winkler foundation. To improve and extend the ability of the strain wedge method, a modified strain wedge (MSW) method is developed, in which a nonlinear lateral deflection of the pile is assumed to describe the varied soil strain distribution in the passive wedge. And then by treating the soil weight involved in the strain wedge as a vertical load at the bottom of the scour hole, an equivalent wedge depth is obtained to consider the effect of scour hole dimensions on the response of laterally loaded piles in sand. The validity of the MSW model is proved by comparisons with a centrifuge test without scour. And its applicability in the problem of a pile with scour is performed by a comparison with a model test and a FE analysis. The analysis shows the pile displacement at the pile head with scour can be obtained by multiplying the corresponding deflection without scour with an amplification factor related to scour depth at large load level. 相似文献
9.
Large-scale field tests were conducted to study set-up effect in open-ended prestressed high-strength concrete pipe piles jacked into stratified soil. Four open-ended prestressed high-strength concrete pipe piles with 13 and 18 m in embedment depth were fully instrumented with fiber Bragg grating sensors and installed. Several restrike dynamic tests were performed on each test pile, with the time interval from 21.5 to 284 hours after installation. Static loading tests (SLTs) were later performed on each test pile at 408 hours after installation to substantiate the dynamic tests. Changes with time in pile bearing capacity and in the shaft and toe resistances were studied based on the results of the pile tests. The development of shaft resistance set-up in different layers was studied in particular. It was found that set-up effect in the shaft resistance is significant and the toe resistance increment was minor. The overall set-up factor of total bearing capacity was found to range from 0.09 to 0.53, and the set-up effect of friction pile is much larger than the end bearing pile. More significant set-up in shaft resistance was observed in fill and alluvium layer. The dimensionless set-up factor A for shaft resistance in marine deposits ranges from 0.5 to 1.43, and it contributes the most to the shaft resistance as the shaft resistance in marine deposits is higher. 相似文献
10.
AbstractMono-pile foundations have been widely used for offshore wind turbines principally due to their convenient construction and cost-effective nature. So far, little attention has been paid to large diameter “semi-rigid” piles that have distinct behaviours from flexible or ideally rigid piles. This paper presents a series of centrifuge model tests to study the deforming and bearing characteristics of a 5.9 dia. semi-rigid pile under lateral loadings in kaolin clay. For monotonic loading, a modified p–y curve analysis model considering rotational soil flow near the rotation centre of pile was proposed, highlighting the limitation of classic plane-strain based plasticity models to evaluate the ultimate lateral pile-soil resistance. For cyclic loading, a strong correlation between the degree of soil degradation and cyclic load amplitude was identified. Besides, a degradation factor model, accounting for various cyclic stress levels and soil depths, was proposed, which can be used to assess the accumulative displacement of semi-rigid piles under cyclic loadings in soft clay. 相似文献
11.
Modulus of Subgrade Reaction for Laterally Loaded Piles in Multiple Layered Foundation 总被引：1，自引：1，他引：1
Lu Ziai
Associate Professor Dept. of Navigation Ocean Engineering Hohai University Nanjing 《中国海洋工程》1997,(4)
-According to the field test data of laterally loaded steel piles at home and abroad,an empiri-cal formula for evaluating the modulus of subgrade reaction under static load in layered soil is proposed.The suggested formula takes account of not only non-linearity of K_s with the depth but also its variationwith the load.It is shown that the computed bending moments along the pile shaft and the deflection atthe pile top are consistent with the measured ones. 相似文献
12.
The pile-driving method produces considerable noise and vibrations. Hence, an auger-drilled pile method was developed as a low-noise and -vibration substitute. However, this method does not guarantee the bearing capacity of the pile unless some amount of pile-driving is performed. Therefore, the noise and vibration problems cannot be completely solved. In this study, a prebored screw pile method is proposed to solve these problems. In this method, piles are constructed by the rotary penetration of a screw pile into a prebored hole filled with some cement milk and whose diameter is smaller than that of the screw pile. To determine the shape of the screw pile, laboratory tests with model screw piles were conducted. Also, field load tests were conducted on an actual screw pile fabricated based on the laboratory test result and on a smooth-surfaced pile. In addition, the behavior of the screw pile was estimated by using three-dimensional finite element analysis. The results of the field load test and the numerical simulation showed that the ultimate bearing capacity and the unit skin friction of the screw pile are very superior to those of the smooth-surfaced pile and the cement milk is an important factor in the prebored screw pile method. 相似文献
13.
港口靠船桩工作性状计算的双参数法 总被引：8，自引：0，他引：8
港口靠船桩是承受重复性荷载或多循环荷载的一种横向承载桩。双参数法能较好地描述靠船桩 (单桩、群桩 )的桩土工作性状。用双参数法进行计算时 ,所给的地面条件必须由重复荷载或多循环荷载作用下实测出来。根据现场试桩资料 ,标定桩土参数 ,即k =mx1/n的指数l/n、桩土相对柔度系数α、桩土综合刚度EI等值 ,可以用来设计试桩附近局部地区同类条件下的其它长桩。对于没有进行试桩的某些工程 ,可以联合运用双参数法和p -y曲线法进行桩的分析 相似文献
14.
Drilled displacement (DD) piles with a screw-shaped shaft (referred to as DD piles) are installed using a continuous full thread hollow rod (without a displacement body) inserted and advanced in the soil by both a vertical force and a torque. As a type of newly developed pile, current understanding of the bearing mechanism of DD piles is unsatisfactory, which restricts their further applications in engineering. The primary aim of this paper is to study the bearing mechanism of this type of pile using a numerical method. First, a numerical model for calculating the bearing capacity of the DD piles was created and validated by a laboratory test. Then, the effects of the parameters of pile–soil interface, soil strength, and pile geometrical parameters on the bearing mechanism of the DD piles were investigated in parametric studies. The results of parametric studies show that the limit shear stress on the pile–soil interface, the friction angle of surrounding sand, screw pitch, and thread width significantly influence the bearing capacity of the DD piles, whereas the friction coefficient at the pile–soil interface and the thread thickness have little effect. Based on the results of the parametric studies, the failure mechanism of the DD piles under vertical load is analyzed. Finally, an equation for predicting the ultimate bearing capacities of helical piles based on cylindrical shear failure was used for estimating the bearing capacity of the DD piles, and the calculated results were verified with the numerical results. 相似文献
15.
Jia-jin Zhou Kui-Hua Wang Ri-Hong Zhang Tian-Long Yan 《Marine Georesources & Geotechnology》2016,34(3):293-301
A static drill rooted nodular pile is a new type of composite pile foundation with high bearing capacity, and mud emissions can be largely reduced using the static drill rooted method. This report presents a model test on the behavior of this composite pile in a test box. The load-displacement response, axial force, skin friction, and mobilized base load are discussed in the report; in particular, the force in the cemented soil was investigated based on the measured data. Moreover, the finite element software ABAQUS was used to help investigate this behavior more thoroughly. It was determined that the function of the cemented soil around the pile shaft was different from that at the enlarged pile base; the stress in the cemented soil around the shaft increased suddenly when nearing the pile base; the ultimate skin friction obtained in the model test was larger than that estimated in the field test; and the relative displacement between the precast nodular pile and the cemented soil could be ignored during the loading process, which corresponded to the result of the field test and demonstrated that the nodular pile and cemented soil act as one entity during the loading process. 相似文献
16.
导管架平台桩基贯入深度的两级模糊模式优选模型 总被引：1，自引：0，他引：1
桩基础是海洋导管架平台结构中的重要组成部分，其贯入深度对海洋平台的造价和运营期间的安全性能起着重要的影响。本文在考虑桩－土之间相互作用非线性特性的基础上，采用非线性等效弹筑模拟海底土层对桩基的作用，对桩基进行有限元分析。由于影响海洋导管架平台桩基础贯入深度的因素很多，而且有些因素带有很大的模糊性，本文采用两级模糊模式优选模型对影响因素进行综合评判，最后得出了适合给定荷载和海底地条件下最为合理的桩基贯入深度方案，具有一定的工程应用价值。 相似文献
17.
利用砂土中扩底抗拔桩的模型试验,研究从开始加载到破坏时扩底抗拔桩地基动态变形全过程的承载特性。试验结果表明:半模试验得到的极限荷载和破坏面均略小于全模试验结果,采用半模试验测量地基变形过程与破坏模式有明显优势,用半模试验代替全模试验是可行的;随着桩顶荷载的增加,扩大头上方的土体由压缩变形逐渐发展为局部的压缩—剪切破坏;扩大头对其上部的桩侧摩阻力有增强作用,对其下部的桩侧摩阻力有削弱作用;扩大头在工作荷载、极限荷载和破坏荷载作用时分担的荷载比例为15%~20%。 相似文献
18.
A fundamental study of pile–soil systems subjected to lateral loads in offshore deposit was conducted using experimental tests and numerical analysis. The emphasis was on the soil–pile rigidity of a laterally loaded pile in marine clay. Rigid- and flexible-pile analyses were conducted for comparison. A framework for determining the lateral load transfer curve (p–y curves) is proposed based on both field and laboratory model tests. A numerical analysis that takes into account the proposed p–y curves was performed for the pile flexibility parameters such as pile diameter, pile length, pile-bending stiffness, and the modulus of subgrade reaction. Based on the analysis, it is shown that the differences in bending moment and lateral displacement are more significant for flexible piles rather than rigid piles. It was found that the p–y curves influence the behavior of flexible piles more than rigid piles, thus the magnitude and distribution of the p–y curves are significantly important in flexible pile design. 相似文献
19.
Two- and three-dimensional finite element analysis programs for pile-soil interaction are compiled. Duncan-Chang's Model is used. The construction sequence of the pier is modeled. The pile-soil interface element is used. The influence of the combination type of piles on the deformation of bank slope and pile behaviour is analyzed. Different designs of a pile-supported pier are compared thoroughly. Calculation results show that the stresses and displacements of the pile are directly related to the distance from the bank slope and the direction of inclination. An inclined prop pile set in the rear platform would remarkably reduce the stresses of piles and the displacement of the pier. 相似文献
20.
Liqiang Sun Yandi Wang Shuwang Yan Jian Chu Xiaoqiang Liu 《Marine Georesources & Geotechnology》2018,36(6):709-721
The super-long and large-diameter steel pipe piles are often adopted for the construction of offshore oil platforms in deep sea. One constructability issue related to driving heavy pipe piles is the pile running. The term pile running refers to the quick penetration of a pile into the seabed as a result of its high self-weight and low resistance from the seabed. The unexpected pile running can cause the steel wire of the hammer to break or even the loss of the hammer. A case study of pile running at an oil platform is introduced in this paper. A simplified theoretical method is proposed to explain the mechanisms of the pile running in this case. A factor of friction degradation is proposed to calculate the dynamic skin friction from the static ultimate skin friction of surrounding soil. The comparisons between the predictions to the case history show that the proposed simplified method can be used to predict the pile running condition. 相似文献