共查询到20条相似文献，搜索用时 203 毫秒
1.
The pile-driving method produces considerable noise and vibrations. Hence, an auger-drilled pile method was developed as a low-noise and -vibration substitute. However, this method does not guarantee the bearing capacity of the pile unless some amount of pile-driving is performed. Therefore, the noise and vibration problems cannot be completely solved. In this study, a prebored screw pile method is proposed to solve these problems. In this method, piles are constructed by the rotary penetration of a screw pile into a prebored hole filled with some cement milk and whose diameter is smaller than that of the screw pile. To determine the shape of the screw pile, laboratory tests with model screw piles were conducted. Also, field load tests were conducted on an actual screw pile fabricated based on the laboratory test result and on a smooth-surfaced pile. In addition, the behavior of the screw pile was estimated by using three-dimensional finite element analysis. The results of the field load test and the numerical simulation showed that the ultimate bearing capacity and the unit skin friction of the screw pile are very superior to those of the smooth-surfaced pile and the cement milk is an important factor in the prebored screw pile method. 相似文献
2.
Drilled displacement (DD) piles with a screw-shaped shaft (referred to as DD piles) are installed using a continuous full thread hollow rod (without a displacement body) inserted and advanced in the soil by both a vertical force and a torque. As a type of newly developed pile, current understanding of the bearing mechanism of DD piles is unsatisfactory, which restricts their further applications in engineering. The primary aim of this paper is to study the bearing mechanism of this type of pile using a numerical method. First, a numerical model for calculating the bearing capacity of the DD piles was created and validated by a laboratory test. Then, the effects of the parameters of pile–soil interface, soil strength, and pile geometrical parameters on the bearing mechanism of the DD piles were investigated in parametric studies. The results of parametric studies show that the limit shear stress on the pile–soil interface, the friction angle of surrounding sand, screw pitch, and thread width significantly influence the bearing capacity of the DD piles, whereas the friction coefficient at the pile–soil interface and the thread thickness have little effect. Based on the results of the parametric studies, the failure mechanism of the DD piles under vertical load is analyzed. Finally, an equation for predicting the ultimate bearing capacities of helical piles based on cylindrical shear failure was used for estimating the bearing capacity of the DD piles, and the calculated results were verified with the numerical results. 相似文献
3.
For the static pressure pile, the most important is to determine the standard value of ultimate bearing capacity of single pile. At present, the bearing capacity of pile foundation is usually determined by the cone penetration test (CPT) test. The empirical formula was used in practice, but the effect of excess pore water pressure generated in the penetration on the measured cone-tip resistance and side friction is neglected. In this study, based on the field test results at Fengyu playground at Yancheng Institute of Technology by CPT and CPTU methods, the bearing capacity of pile was predicted by the standardized methods, the LCPC (France method) and CPTU direct prediction methods. The prediction was also compared with the results by the static load test method. The prediction accuracy of the CPTU method was then discussed as well. The results reveal that the accuracy of the CPTU method was the highest, which was consistent with the results obtained by the static load test method. It is the best method and worthy of being applied for predicting bearing capacity of piles in engineering applications. 相似文献
4.
AbstractAn experimental study of the performance of concrete pipe piles during installation under different penetration speeds and static load tests on the piles in sand is presented. The applied jacking force, the amount of pile penetration, length of soil plug formed and ultimate bearing capacity were measured during the model tests. The results showed that the concrete pipe piles were partially plugged and the behavior of the soil plug was significantly affected by the penetration speed. The lower the penetration speed, the larger the soil plug formed which in turn leads to a greater ultimate bearing capacity. The size of soil plug can be evaluated by the m value defined as the ratio of the volume of the soil plug to that of the penetrated pile wall. The relationship between the m value and the penetration speeds can be used to estimate the amount of soil plug and the depth of penetration for an open-ended concrete pipe pile jacked into sand. 相似文献
5.
Most field tests are carried out using working piles for verification purposes in China, and loading tests are terminated before achieving true pile capacity. In this work, two full-scale destructive loading tests on tension piles instrumented with strain gauges were conducted to capture true pile capacity. The load-displacement response, load transfer, and threshold of the pile-soil relative displacement for fully mobilizing skin resistance in the uplift case were discussed. It was found that the shaft resistance degradation is observed to be along the pile depth with a reduction factor of 0.905 to 0.931, and the thresholds of pile-soil relative displacement for fully mobilizing skin resistance of the tension pile in different soils are found to be in the range 0.67% to 1.34% of the pile diameter. Based on the field test results, a simple softening model was proposed to describe the degradation behavior of skin friction along the pile-soil interface. Further study was conducted to assess the influence of the threshold of pile-soil relative displacement for fully mobilizing skin friction and the reduction factor on the skin friction. As to the analysis of the response of single pile subjected to tension load, a highly effective iterative computer program was developed using the proposed skin friction softening model. Comparisons of the load-settlement response for the well-instrumented tests were given to demonstrate the effectiveness and accuracy of the proposed simple method. 相似文献
6.
Large-scale field tests were conducted to study set-up effect in open-ended prestressed high-strength concrete pipe piles jacked into stratified soil. Four open-ended prestressed high-strength concrete pipe piles with 13 and 18 m in embedment depth were fully instrumented with fiber Bragg grating sensors and installed. Several restrike dynamic tests were performed on each test pile, with the time interval from 21.5 to 284 hours after installation. Static loading tests (SLTs) were later performed on each test pile at 408 hours after installation to substantiate the dynamic tests. Changes with time in pile bearing capacity and in the shaft and toe resistances were studied based on the results of the pile tests. The development of shaft resistance set-up in different layers was studied in particular. It was found that set-up effect in the shaft resistance is significant and the toe resistance increment was minor. The overall set-up factor of total bearing capacity was found to range from 0.09 to 0.53, and the set-up effect of friction pile is much larger than the end bearing pile. More significant set-up in shaft resistance was observed in fill and alluvium layer. The dimensionless set-up factor A for shaft resistance in marine deposits ranges from 0.5 to 1.43, and it contributes the most to the shaft resistance as the shaft resistance in marine deposits is higher. 相似文献
7.
螺旋桩芯劲性复合桩（helix stiffened cement mixing pile，简称HSCM桩）是一种新型复合桩，其成桩工艺会对桩身及其承载性能有较大影响。为验证HSCM桩在软黏土中同步旋进注浆工艺的可行性，并研究其成桩参数对抗压承载性能的影响，设计了2组缩尺模型试验，包括不同叶片数量与钻进速度的HSCM桩与对比螺旋桩。通过在高岭土制备的软黏土中成桩，并进行抗压承载性能及桩身几何尺寸测试，分析HSCM桩的成桩参数与水泥土桩身间的关系。试验结果表明：同步旋进注浆工艺能够在螺旋桩周围形成倒圆台状的水泥土桩身，水泥土桩身的平均黏结直径约为叶片直径的1.17～1.35倍；适当增加叶片数量能够使水泥与土体充分拌和，提高水泥土桩身的完整性与连续性，以改善HSCM桩的成桩质量；钻进速度大幅提高会导致注浆量不足，减小水泥土桩身的黏结直径与刚度；试验条件下HSCM桩的抗压极限承载力是螺旋桩的3.83～3.93倍，桩径扩大提高了侧摩阻力，注浆工艺加固并提高了土体强度，弥补了叶片在旋进过程中扰动土体造成强度降低的问题。 相似文献
8.
为解决在钢管桩水平静载试验中更加高效、安全和准确进行桩身内力变形测试和分析的问题,文章针对打入钢管桩中的应变传感器和测斜管分别提出实用且可靠的安装、保护和测试方法;将该方法应用于西非某码头工程,在大直径钢管桩水平静载试验中进行应力和变形测试。研究结果表明,该安装和保护方法实用且可靠,可保证水平试验过程中钢管桩的内力变形情况得到如实测试和记录,对研究分析大直径钢管桩受水平荷载时桩身弯矩和水平位移的变化情况意义重大,可为类似项目的设计和施工提供参考。 相似文献
9.
《中国海洋工程》2021,(3)
The low side friction of piles in coral sand results in the low bearing capacity of foundations. In this paper, expansive concrete pile is utilized to improve the bearing capacity of pile foundations in coral sand. Both model tests and numerical simulation are performed to reveal the bearing mechanism of expansive concrete pile in coral sand.Results showed that the lateral earth pressure near pile increases obviously and the side friction of piles is improved,after adding expansion agent to the concrete. The horizontal linear expansion is 1.11% and the bearing capacity increased 41% for the pile, when 25% expansion agent is added. Results in finite element numerical simulation also show that ultimate bearing capacity increases with the increase of the linear expansion ratio. Besides, the area for obvious increase in side friction is below the surface of soil about three times the pile diameter, and the expansion leads to a high side friction sharing of the pile. Therefore, the cast-in-place expansive concrete pile is effective in improving the bearing capacity of piles in coral sand. 相似文献
10.
AbstractPile foundation is the most popular option for the foundation of offshore wind turbines. The degradation of stiffness and bearing capacity of pile foundation induced by cyclic loading will be harmful for structure safety. In this article, a modified undrained elastic–plastic model considering the cyclic degradation of clay soil is proposed, and a simplified calculation method (SCM) based on shear displacement method is presented to calculate the axial degradated capacity of a single pile foundation for offshore wind turbines resisting cyclic loadings. The conception of plastic zone thickness Rp is introduced to obtain the function between accumulated plastic strain and displacement of soil around pile side. The axial ultimate capacity of single piles under axial cyclic loading calculated by this simplified analysis have a good consistency with the results from the finite element analysis, which verifies the accuracy and reliability of this method. As an instance, the behavior of pile foundation of an offshore wind farm under cyclic load is studied using the proposed numerical method and SCM. This simplified method may provide valuable reference for engineering design. 相似文献
11.
In the field of ocean engineering, pile foundations are extensively used in supporting several structures. In many cases, piles are subjected to significant lateral loads. The environment prevalent in the ocean necessitates the piles to be designed for cyclic wave loading. In this investigation, the behaviour of rigid piles under cyclic lateral loading has been studied through an experimental programme carried out on model piles embedded in a soft marine clay. Static tests were also conducted on piles embedded in a clay bed prepared at different consistencies suitable to field situations. Cyclic load was applied by using a specially designed pneumatic controlled loading system. Tests were conducted on model piles made of mild steel (MS), aluminium and PVC with wide variation in pile soil relative stiffness. For cyclic load levels less than 50% of static lateral capacity, the deflections are observed to increase with number of cycles and cyclic load level and stabilise after a certain number of cycles. For cyclic load levels greater than 50% of static lateral capacity, the deflections are observed to increase enormously with number of cycles. The results of post-cyclic load tests indicate that the behaviour under static load can improve for cyclic load levels less than 40% of the static lateral capacity. The variations in the load capacity due to cyclic loading are explained in terms of the changes in strength behaviour of soil. 相似文献
12.
A research on super-long piles has been primarily based on cast-in-place bored piles. In this article, field tests associated with selected measuring technologies were conducted on two super-long steel pipe piles in offshore areas to investigate the behaviors and performance of super-long steel pipe piles. The strain along the pile shaft was monitored by adopting the Brillouin optical time domain reflection and fiber Bragg grating techniques. Static load tests were also conducted on two test piles to determine the bearing capacities. In addition, the axial forces, relative displacements between piles and soils and pile shaft resistances were calculated based on the measured strain. According to the results of the static load tests, the ultimate bearing capacities of the two test piles are greater than 15,000 and 15,500 kN. Both of these values meet the design requirements. In addition, the two test piles can be treated as pure friction piles, and the load transfer mechanism and relationships between the pile shafts and relative displacements are also discussed. Finally, recommendations for practical engineering and significant conclusions are presented. 相似文献
13.
In this article, two full-scale pile loading tests were conducted to observe the field performance of the super-long bored piles, and a simplified approach for nonlinear analysis of the load-displacement behavior of a single pile was presented. The field tests on piles indicates that, under the maximum test load, more than 70% of the pile top settlement is caused by the compression of pile shaft. For practical purposes, the pile top settlement can be reduced through improving the pile shaft strength. When the load reaches the maximum test load, the proportion of the load carried by the pile tip is approximately 30%. The super-long pile is functioning as an end-bearing friction pile. The skin friction at shallow depth is fully mobilized and decreases from a peak value with increasing load. However, the skin friction of deeper soil is not fully developed due to less relative displacement. Furthermore, a BoxLucas1 model is used to capture the relationship between unit skin friction and pile-soil relative displacement, whereas a hyperbolic model is used to describe the relationship between toe stress and pile base displacement. Based on the BoxLucas1 model and the hyperbolic model, a load transfer method is used to clarify the response of a single pile, and a computational flow chart is developed. The efficiency and accuracy of the present method is verified using the field tests on piles. The proposed simple analytical approach is economical and efficient, resulting in savings in time and cost. 相似文献
14.
自升式钻井平台插桩是地基土在桩靴荷载作用下发生连续的塑性破坏的动态过程,当地基极限承载力等于桩靴荷载时插桩完成。经典土力学极限承载力理论对土体潜在滑动面做了假设,无法有效分析土体内部的破坏过程。本研究应用有限元法（FEM ）对插桩过程进行了模拟,得到地基土的破坏机制以及中间荷载下土体的应力、应变情况,通过和各理论公式计算的极限承载力进行对比分析,分析影响地基极限承载力的因素。研究表明,基础宽度与硬土层厚度的比值 B/H越大,下卧软土层越容易发生塑性破坏,极限承载力明显下降,当B/H＜0．286时,可以忽略下卧软土层对地基承载力的影响。 相似文献
15.
16.
利用室内半模试验和颗粒流数值模拟,揭示多层砂土地基扩底桩单桩抗压承载特性及变形特征。结果表明,通过对比分析极限承载力与H_h/D(持力层厚度与扩大头直径之比)的关系可以看出,单桩的抗压极限承载力随H_h/D逐渐增加,当H_h/D超过2.0时,极限承载力基本不再增加,此时的单桩抗压极限承载力稳定在300.01~303.25 N,是H_h/D=0.5时极限承载力(183.83 N)的1.65倍。扩大头下部土体发生局部压缩-剪切破坏,破坏面从扩大头底面边缘向斜下方扩展,在水平方向影响范围达到最大后逐渐向桩内侧收缩;荷载作用越大,地基破坏区域越大,相应的极限抗压承载力也越大;持力层厚度增加,扩大头分担的荷载比例增大,分担的荷载达到稳定需要的桩顶位移也越大,H_h=0.5 D试验扩大头分担的荷载比例稳定时为60%,对应的桩顶位移约为29 mm;桩顶位移达到33 mm后,H_h=1.0~3.0 D试验稳定在63%~65%之间;通过细观颗粒流理论对砂土移动特性的研究发现,持力层厚度从0.5 D增大至2.0 D,破坏面的起始扩展角度从31°增大至42°。数值模拟研究结果与模型试验数据吻合效果良好,证明该方法分析多层砂土地基扩底桩单桩抗压荷载传递机理是可行的。 相似文献
17.
Helical piles are structural deep foundation elements, which can be categorized as torque-driven piles without any limitations to implement in marine situations. Different methods are used to predict the axial capacity of helical piles, such as static analysis, but have some limitation for this type of piles on marine conditions. In situ testing methods as supplement of static analysis have been rarely used for helical piles. In geotechnical engineering practice, the most common in situ tests particularly applicable for coastal or offshore site investigation are cone penetration test (CPT) and piezocone penetration test (CPTu). The CPT is simple, repeatable, and prepares the continuous records of soil layers. In this paper, a data bank has been compiled by collecting the results of static pile load tests on thirty-seven helical piles in ten different sites including CPT or CPTu data. Axial capacities of thirty-seven helical piles in different sites were predicted by direct CPT methods and static analysis. Accuracy estimation of ten direct CPT methods to predict the axial capacity of helical piles was investigated in this study. Comparisons have been made among predicted values and measured capacity from the pile load tests. Results indicated that the recently developed methods such as NGI-05 (2005), ICP-05 (2005), and UWA-05 (2005) predicted axial capacity of helical piles more accurately than the other methods such as Meyerhof (1983), Schmertmann (1978), Dutch (1979), LCPC (1982), or Unicone (1997). However, more investigations are required to establish better correlation between CPT data and axial capacity of helical piles. 相似文献
18.
This paper presents a series of full-scale load tests on long bored piles instrumented with strain gauges along the shafts, including eight field tests of piles loaded to failure and one non-destructive pile load test. The load-displacement response, skin friction, end resistance, and the threshold of the pile-soil relative displacement for fully mobilizing skin resistance were discussed. A simple softening model was proposed to describe the degradation behavior of the skin friction along the pile-soil interface and the load-displacement relationship developed at the pile base. It is found that the shaft resistance degradation investigated in the non-destructive load test only occurs at a shallow depth, and the skin friction of deeper soil is not fully developed. However, unlike the results of the non-destructive load tests, the softening is accompanied by a reduction in skin friction and observed to be along the whole pile depth. The thresholds of pile-soil relative displacement for fully mobilizing skin resistances in different soils have been found to be in the range 0.6% to 2.4% of the pile diameter. Moreover, in practical applications, a bilinear model is assumed to be feasible in analyzing the load-settlement relationship developed at the end of non-destructive pile, whereas the load transmission curve of the soils below the pile base corresponds to a softening model in the field tests of piles loaded to failure. 相似文献
19.
大直径钢管桩土塞效应的判断和沉桩过程分析 总被引：5，自引：0，他引：5
港口工程和海洋工程中出现了越来越多的大直径超长钢管桩。由于这种桩直径较大,土塞的形成对桩的可打入性和承载力有较大的影响。鉴于此,根据大直径和超大直径钢管桩土塞性状的特殊性,考虑了桩直径对侧壁摩阻力、端阻力的影响,引入了尺寸效应系数,重新建立了土塞微分体的静力平衡方程,提出了采用改进的静力平衡法进行土塞效应判断,同时采用波动方程法近似模拟土塞与桩管内壁的相互作用,建立了简化的土塞与桩壁相互作用模型,并用该方法进行实际工程的打桩分析,分析结果表明该方法对土塞效应的判断、打桩过程的预测等与工程实测数据吻合较好。 相似文献
20.
S. Moshfeghi 《Marine Georesources & Geotechnology》2019,37(1):67-80
Drilled displacement piles (DDPs) are known as an alternative to conventional foundations in coastal areas, given the elimination of environmental impacts and difficulties caused by installation process of driven piles and more consistency with environment. Despite increasing employment of these piles, the extent of research works does not yet suffice the requisites to reach a routine design. This paper aims to analyze six cone penetration test (CPT)-based methods of determining the bearing capacity of DDP. The statistical and reliability-based approaches were used in two parts of assessing performance of the methods with respect to soil–pile characteristics followed by evaluating reliability of the prediction outcome. A database is compiled including 65 DDP load tests with adjacent CPT profiles. Performance of the methods are analyzed. Finally, a reliability parameter, i.e., confidence interval, is introduced to demonstrate a more realistic insight into the evaluations by expressing performance of the methods in terms of a range for possible average values of the predictions ratios, rather than simply an arithmetic mean. The study reveals that the commonly used CPT-based methods which have not been specifically developed for DDP show great potential for design. The results indicate that the investigated methods can have promising performance if some modifications are applied. 相似文献