共查询到20条相似文献，搜索用时 46 毫秒
1.
The experimental studies on flow-induced vibrations(FIV) reduction of two side-by-side flexible cylinders inclined at 45° by using the helical strakes were carried out in a towing tank. The main aim of the experiment is to check whether the helical strakes with a pitch of 17.5 D and a height of 0.25 D, which is considered as the most effective vibration suppression device for the isolated cylinder undergoing vortex-shedding, still perform very well to reduce FIV of two inclined flexible cylinders in a side-by-side arrangement. The vibration of two identical inclined cylinders with a mass ratio of 1.90 and an aspect ratio of 350 was tested in the experiment. The center-to-center distance between the two cylinders was 3.0 D. The uniform flow was simulated by towing the cylinder models along the tank.The towing velocity varied from 0.05 to 1.0 m/s with an interval of 0.05 m/s. The maximum Reynolds number can be up to 1.6×104. Three cases were experimentally studied in this paper, including two side-by-side inclined smooth cylinders, only one smooth cylinder fitted with helical strakes in the two side-by-side inclined cylinders system and both two cylinders attached with helical strakes. The variations of displacement amplitude, dominant frequency, FIV suppression efficiency and dominant mode for the two side-by-side inclined cylinders with reduced velocity were shown and discussed. 相似文献
2.
The flow patterns in the near wake of a cylinder (either circular or square in shape, D=25 mm) placed in the proximity of a fully developed turbulent boundary layer (thickness δ=0.4D) are investigated experimentally using particle image velocimetry (PIV). The effects of changing the gap height (S) between the cylinder bottom and the wall surface, over the gap ratio range S/D=0.1–1.0, have been investigated. The results show that both the ensemble-averaged and instantaneous flow fields are strongly dependent on S/D. The flow patterns for the two types of cylinders share many similarities with respect to the change in S/D, such as the reduced recirculation length and increased velocity fluctuation in the near wake with increasing S/D, as well as the trend of suppression of vortex shedding at small S/D and onset of vortex shedding at large S/D. However, developments of the shear layers, in terms of wake width, flow curvature, etc., are considerably different for these two types of cylinders. In general, the wake development and momentum exchange for the square cylinder are slower those for the circular cylinder at the same gap ratio. Correspondingly, it is shown that the periodic vortex shedding is delayed and weakened in the case of square cylinder, as compared to that of the circular cylinder at the same S/D. 相似文献
3.
为研究四柱体布置情况下倒角半径变化对柱体绕流水动力特性的影响,使用Fluent软件,采用大涡模拟方法研究了在雷诺数Re=3 900下6种不同倒角半径的柱体在方形四柱体布置时的三维流场。在模型分析验证有效后,分析了柱体后方瞬时流场、水动力参数、时均流场的变化情况。分析结果表明:随着倒角半径的增大,上游柱体的平均阻力系数逐渐减小,下游柱体的平均阻力系数除了在R~+=0.1处增幅很大以外,其余均随倒角半径变大而平稳变大;各柱体的升力系数均方根变化趋势基本相同;R~+=0.1、0.5时,上下游两柱体的升力系数曲线相位相反,而在R~+=0.2、0.3和0.4时,上下游两柱体的升力系数曲线相位相同。 相似文献
4.
H.M. Badr 《Ocean Engineering》1994,21(1)
The problem of oscillating inviscid flow over an elliptic cylinder is studied for various angles of attack. The flow is incompressible and two-dimensional and the oscillations are harmonic. The flow direction is always normal to the cylinder axis and oscillations are only allowed in the magnitude of the free stream velocity. The study focuses on the hydrodynamic forces acting on the cylinder as well as the surface pressure distribution and their time variation. The parameters involved are the cylinder axis ratio, the angle of attack and the Strouhal number. The variables are normalized in such a way that the solutions for the problems of oscillating flow over flat plates and circular cylinders can be easily obtained as special cases. Analytical expressions are given for the drag coefficient, the lift coefficient, and the surface pressure distribution and their variation with time. Similar analytical expressions are given for the special cases of circular cylinders and inclined flat plates in oscillating inviscid flows. 相似文献
5.
The unsteady flow past a circular cylinder which starts translating and transversely oscillating from rest in a viscous fluid is investigated at a Reynolds numbers of R=103 and at a Strouhal number of π/4 and for the maximum oscillatory to translational velocity ratios between 0.1 and 1.0. This study is based on numerical solutions of the two-dimensional unsteady Navier–Stokes equations. The object of the study is to examine the effect of increase of velocity ratio on the near-wake structure as well as the hydrodynamic forces acting on the cylinder. For all velocity rates a periodic structure of vortex evaluation and shedding develops which is repeated exactly as time advances. Vortex dynamics close behind the body are affected by changing acceleration of the cylinder and a changeover from one mode to a different mode of vortex formation is observed with increase in velocity ratio. A comparison of the present results with the impulsively started translating case has been included to illustrate the effect of velocity ratio on drag at small values of velocity ratio. 相似文献
6.
Laminar flow past a circular cylinder with 3 small control rods is investigated by numerical simulation. This study is concerned with the suppression efficacy of vortex induced vibration by small control rods located around a main cylinder. The effects of the attack angle and rod-to-cylinder gap ratio on the hydrodynamics and vibration responses of the main cylinder are investigated. The attack angle of α = 45° is performed as the critical angle for VIV suppression of 3 control rods. The 3 control rods have no effect on VIV suppression when the attack angle is less than the critical angle. The 3 control rods have an excellent VIV suppression efficacy when the attack angle is larger than the critical angle. The transverse vibration frequency of the cylinder with 3 control rods is less than that for an isolated cylinder for all the configurations. The numerical results for the configurations of α = 45° & 60°, G/D = 0.6–1.2 show excellent suppression efficient among the cases investigated in this study. The best suppression efficient is found at α = 45°, G/D = 0.9 for 3 control rods. 2 rods in behind of the main cylinder perform more efficient than that of 1 rod in front for VIV suppression as the gap ratio of G/D less than 1.0. 相似文献
7.
Vibration of two elastically mounted cylinders in an oscillatory flow at a Keulegan-Carpenter number of 10 is simulated numerically. The two cylinders are rigidly connected with each other and are allowed to vibrate in the cross-flow direction only. The aim of this paper is to identify the effects of the orientation of the cylinders and the gap between the cylinders on the vibration. The two-dimensional Reynolds-Averaged Navier-Stokes equations are solved to predict the flow and the cylinder vibration is predicted using the equation of motion. When the two cylinders are in a tandem arrangement, a combined single pair flow regime and attached pair flow regime are observed as reduced velocity exceeds 10 and this combined regime and the single pair regime occurs intermittently. Periodic vibration is found when the two cylinders are in a staggered arrangement with a 45° flow attack angle. When the two cylinders are in a side-by-side arrangement, a new single vortex regime is observed. This single vortex remains attached to the cylinder surface and rotates around the cylinder. The intermittent switch between this single vortex regime and the single pair regime are observed. 相似文献
8.
H. Omara G. M. Abdeelaal K. Nadaoka A. Tawfik 《Marine Georesources & Geotechnology》2020,38(2):133-143
AbstractBecause scour is one of the main reasons for bridge failure, this study focuses on accurately predicting the maximum scour depth around different vertical and inclined piers. Scouring is an issue of concern in the bridge design process, as most existing equations for predicting local scour near bridge piers suffer from over- or underprediction issues, resulting in higher foundation costs or bridge failure and inaccurate predictions of the scour around piers. The dimensionless maximum scour depths (ys/D) of vertical and inclined piers were investigated for seven pier shapes with different L/D ratios and four inclination angles (θ) under shallow flow conditions. The inclined pier configuration reduced the ys/D of the piers. The maximum ys/D was observed for a rectangular pier with an L/D of 4.5 in both vertical and inclined configurations (θ of 10, 15 and 21°, respectively). The ys/D was significantly decreased by increasing the angle of the pier from 10 to 30°. The ys/D of the inclined rectangular piers decreased as θ decreased from 30 to 10° and the L/D ratio increased from 1 to 4.5. The best ys/D results were obtained for inclined rectangular piers at a θ value of 30° and an L/D ratio of 7.5 compared to other shapes and inclination angles. New equations were developed to predict the local scour depth for circular, square and rectangular bridge piers. The equations yielded excellent results for predicting the maximum clear water scour depth around vertical and inclined piers with inclination angles of 10, 15, 21 and 30°, respectively. 相似文献
9.
H.M. Badr 《Ocean Engineering》1994,21(4)
The problem of oscillating viscous flow over a stationary cylinder of elliptic cross-section is investigated. The free stream direction is horizontal and is always normal to the cylinder axis and oscillations are only allowed in the magnitude of the stream velocity. The flow is incompressible and two-dimensional and the free steam oscillations are harmonic. The elliptic cylinder considered has a major-minor axis ratio of 0.6 and is inclined to the free stream direction at angles of incidence of either 30 or 60°. The investigation is based on the solution of the time-dependent Navier-Stokes equations together with the mass conservation equation. The parameters involved are the cylinder axis ratio, angle of incidence, Reynolds number, and Strouhal number. The Reynolds number ranges between 102 and 103 and the Strouhal number ranges between π/4 and π/2. The time variation of the flow field is presented in the form of streamline patterns as well as surface vorticity distribution. The surface pressure distribution and the time variation of the in-line and transverse force coefficients are also presented and compared with an inviscid flow solution for the same problem. The comparison between viscous and inviscid flow results shows a better agreement for higher values of Reynolds and Strouhal numbers. 相似文献
10.
并列圆柱体在均匀流场中的涡激振动十分复杂，但又广泛存在于实际工程之中。当两柱在流体激励作用下产生振动时，由于同时存在着流固耦合作用和柱间干扰作用，而使周围流场变得更加复杂。本文对并列刚性和弹性圆柱的流场分类，Ｓｔｒｏｕｈａｌ数及流体载荷等问题进行了综述，在此基础上提出了进一步研究的建议。 相似文献
12.
基于Fluent流体计算平台,运用大涡模拟方法对亚临界雷诺数Re=3900下“X”形排列五圆柱体结构群三维绕流特性进行研究,主要分析来流攻角α与间距比L/D两个关键参数对五圆柱体结构群的尾流区三维涡结构演化与流体力系数的影响,并揭示其内在流动互扰机理。研究表明:来流攻角和间距比的变化对五圆柱体结构群流动控制及互扰效应的影响显著。在小间距比工况下,观察到柱体群间隙区域内流体高速流动的现象,导致五圆柱体之间的互扰作用十分强烈。间隙流对中间圆柱体和下游圆柱体有较强的冲击作用,对其表面的流体力分布特性有显著的影响。另外,大间距比工况下,当α=0°与L/D≥5.0工况时,柱体群尾流效应强于其间隙流效应。当α=22.5°与L/D=7.0时,位于下游与中间处的圆柱体流体绕流特性存在较大差异。而当α=45°与L/D≥6.0时,位于上游与中间处的圆柱体尾流区均会产生正负交替的漩涡结构。 相似文献
13.
The response of an oscillating circular cylinder at the wake of an upstream fixed circular cylinder was classified by different researchers as galloping, wake induced galloping or wake induced vibration. Furthermore it is already known that a sharp edge square cylinder would undergo galloping if it is subjected to uniform flow. In this study the influence of the wake of a fixed circular cylinder on the response of a downstream square cylinder at different spacing ratios (S/D = 4, 8, 11) is experimentally investigated. The subject appears not to have received previous attention. The lateral displacements, lift forces and the pressure data from gauges mounted in the wake of the oscillating cylinder are recorded and analyzed. The single degree of freedom vibrating system has a low mass-damping parameter and the Reynolds number ranges from 7.7 × 102 to 3.7 × 104.In contrast to that for two circular cylinders in tandem arrangement, the freely mounted downstream square cylinder displays a VIV type of response at all spacing ratios tested. There is no sign of galloping or wake induced galloping with the square cylinder. With increase at the spacing ratio the cross-flow oscillations decrease. It is shown that the vortices arriving from the upstream fixed circular cylinder play a major role on the shedding mechanism behind the downstream square cylinder and cause the square cylinder to shed vortices with frequencies above Strouhal frequency of the fixed square cylinder (St = 0.13). The VIV type of oscillations in the downstream square cylinder is most probably caused by the vortices newly generated behind the square cylinder. 相似文献
14.
The main purpose of this study is to establish a better understanding of the relationship between drag reduction and surface roughness. Experiments were conducted to measure the force and flow characteristics of a circular cylinder with different types of artificial surface roughness over the range 6 × 103 < Re < 8 × 104 (Re is based on the cylinder diameter D). The roughness cylinder was formed by covering the exterior surface of the cylinder with uniformly distributed (1) sandpaper, (2) netting, and (3) dimples. The roughness coefficient ranged from k/D = 0.0028 to 0.025 (k is the roughness height). A detailed quantitative measurement of the flow field around the cylinder using Particle Imaging Velocimetry (PIV) was carried out. The hydrodynamic force coefficients (drag and lift) of the rough cylinders are compared against those of a smooth cylinder measured under the same flow conditions. It is found that certain configuration of surface roughness significantly reduces the mean drag coefficient of the cylinder, particularly at large Reynolds numbers. In addition, the root-mean-square (r.m.s.) lift coefficient of the rough cylinders is considerably lower than that of a smooth cylinder. 相似文献
15.
Peter R. Payne 《Ocean Engineering》1981,8(5):541-545
The skin friction of a two-dimensional planing flat plate is made up of two opposing components; a drag force from the flow aft of the stagnation line and an opposing thrust force from the jet flow. This paper is concerned only with the drag term and the wake velocity defect which it causes in the water behind the transom.It is concluded that the skin friction is less than would be expected from a flat plate at ambient static pressure (Dfo say) and is approximately equal to Dfo (1 − CR), where CR is the normal force coefficient based on wetted area. The wake velocity decrement due to this drag is found to be significant, particularly for surface piercing propellers. 相似文献
16.
AbstractThe mechanism of local scour under two vibrating pipelines is investigated numerically in this research. A sediment scour model is adopted to estimate the motion of sediment. The general moving objects model, which is dynamically coupled with fluid flow, is set up to simulate the vortex-induced vibration (VIV) of the pipeline. The sediment scour model and pipeline vibration model are verified with the previous experimental results and show good agreement. Then, the coupling effects between the pipeline vibration and the local scour are investigated numerically. The effects of G/D (the ratio of the distance between the two pipelines to the diameter of the pipelines) on the local scour and the VIV of the pipeline are examined. The results indicate that the maximum scour depth under the vibrating pipelines is much larger than the scour depth under the fixed pipelines. Due to the shadowing effect of the upstream pipeline, the maximum scour depth under the upstream pipeline is deeper than that under the downstream pipeline. The pipeline vibration magnitude is closely related to the strength of the vortex that sheds behind the pipeline. The effect of G/D on the shape and strength of the vortices that shed behind the pipelines is significant. 相似文献
17.
Necati Mahir 《Ocean Engineering》2009,36(5):357-367
In this study, two- and three-dimensional numerical simulations were performed to investigate the effect of the flow structure in the wake of a square cylinder placed near a plane wall by applying a fully implicit finite-difference method to the Navier-Stokes equations. The gap ratio between the cylinder and the wall, G/D, was varied from 0.2 to 4 for the Reynolds numbers of 175, 185 and 250. The role of the 3D structure on the lift and drag coefficients and Strouhal number was investigated. The results were compared with those of the 2D numerical simulations. The deviations of the 3D flow structure of the cylinder-wall pair from that of a single cylinder were also reported. At Re=250, B type secondary vortices were determined in the wake region. At Re=175 and 185, transition from A type vortex to fully periodic B type vortices was observed when the cylinder was brought closer to the wall. 相似文献
18.
基于计算流体力学(CFD)开源代码OpenFOAM开展了不同雷诺数(Re=100、1500和3900)和倾斜角度(-60°≤α≤60°)工况下倾斜圆柱绕流流场的三维数值模拟,研究倾斜圆柱绕流的三维瞬时及时均尾流流场、流线拓扑、升阻力系数与旋涡脱落频率随雷诺数及倾斜角度变化的规律,探讨在顺流向及逆流向情况下独立性原则对倾斜圆柱绕流的适用性。研究结果表明:随着圆柱倾角的增大,倾斜圆柱尾流产生较为明显的轴向流,尾流旋涡脱落受到明显抑制,细碎旋涡逐渐消失,尾流宽度随之减小;随着雷诺数的增大,圆柱尾流涡管发生明显的变形,展向掺混使得大量细碎旋涡产生,呈现出明显的三维特性。在不同雷诺数下,阻力系数均值、升力系数均方根及无量纲涡脱频率在一定倾角范围内符合独立性原则。 相似文献
19.
Experimental studies were carried out to investigate the response features of an inclined flexible bare cylinder as well as a straked cylinder in a towing tank, with the main purpose of further improving the understanding of the effect of yaw angle on vortex-induced vibration (VIV) suppression. Four yaw angles (a = 0°, 15°, 30°, 45°), which is defined as the angle between the cylinder axis and the plane orthogonal to the oncoming fluid flow, were tested. The cylinder model was towed along the tank to generate a uniform fluid flow. The towing velocity was in the range of 0.05–1.0 m/s with an interval of 0.05 m/s. The corresponding Reynolds number ranged from 800 to 16000. The strakes selected for the experiments had a pitch of 17.5D and a height of 0.25D, which is generally considered as the most effective configuration for VIV suppression of a flexible cylinder in water. The experimental results indicate that VIV suppression effectiveness of the inclined flexible straked cylinder is closely related to the yaw angle. The displacement amplitudes are significantly suppressed in both cross-flow (CF) and in-line (IL) directions at a = 0°. However, with increasing yaw angle, the suppression efficiencies of the CF and IL displacement amplitudes gradually decrease. In addition, the CF dominant frequencies of the straked cylinder obviously deviate from those of the bare cylinder at a = 0° and 15°. This deviation is substantially alleviated with increasing yaw angle. The IL dominant frequencies show less dependency on the yaw angle. Similar trends are also observed on the dominant modes of vibration and the mean drag coefficients. 相似文献
20.
Helical strakes have been widely applied for suppressing the vibration of flexible cylinders undergoing vortexshedding in offshore engineering. However, most research works have concerned on the application of helical strakes for the isolated flexible cylinder subjected to vortex-induced vibration(VIV). The effectiveness of helical strakes attached to side-by-side flexible cylinders in vibration reduction is still unclear. In this paper, the response characteristics of two side-by-side flexible cylinders with and without helical strakes were experimentally investigated in a towing tank. The configuration of the helical strakes used in the experiment had a pitch of 17.5D and a height of 0.25D(where D is the cylinder diameter), which is usually considered the most effective for VIV suppression of isolated marine risers and tendons. The center-to-center distance of the two cylinders was 3.0D. The uniform flow with a velocity ranging from 0.05 m/s to 1.0 m/s was generated by towing the cylinder models along the tank. Experimental results, including the displacement amplitude, the dominant frequency, the dominant mode,and the mean drag force coefficient, were summarized and discussed. For the case where only one cylinder in the two-cylinder system had helical strakes, the experimental results indicated that helical strakes can remarkably reduce the flow-induced vibration(FIV) of the staked cylinder. For the case of two straked cylinders in a side-by-side arrangement, it was found that the performance of helical strakes in suppressing the FIV is as good as that for the isolated cylinder. 相似文献