共查询到19条相似文献，搜索用时 156 毫秒
1.
不同倒角半径柱体绕流数值模拟及水动力特性分析 总被引：3，自引：1，他引：2
为研究倒角半径变化对柱体绕流水动力特性的影响,本文使用Fluent软件,采用大涡模拟对雷诺数Re=3 900下的6种不同倒角半径的三维柱体进行了研究。在模型验证基础上,分析了由方柱渐变到圆柱过程中后方流场速度的时均特性及瞬时涡脱落变化规律,给出了不同倒角半径下的升、阻力系数值及无量纲涡脱频率St数。分析结果表明:平均阻力系数随倒角半径的增加而降低,在倒角半径为0.2D时下降速率最大,相较方柱降幅达到50%;升力系数均方根在倒角半径为0.1D~0.2D时变化最显著,减小约93%; St数随倒角半径增加而增大,在倒角半径为0.4D时可达到最大值;回流区长度随倒角半径的增加呈先增大后减小的趋势,其长度在倒角半径为0.2D时达到最大;尾涡宽度在倒角半径为0.0D最大,后随倒角半径增加逐渐下降,且当倒角半径大于0.2D以后变化不大。本文研究结果可为柱体绕流研究及相关工程应用提供参考。 相似文献
2.
不同倒角半径下方柱绕流的数值模拟及水动力特性研究 总被引：1，自引：0，他引：1
为了研究不同倒角半径对方柱绕流特性的影响,采用有限体积法,模拟了雷诺数Re为22 500、倒角半径为0.1D(D为方柱边长的长度)、0.2D和0.3D时方柱的绕流过程。方柱近壁面采用增强壁面函数,模型采用SST k–?湍流模型。根据模拟结果给出了不同倒角半径下方柱的流场涡量图以及阻力系数Cd和升力系数Cl;利用快速傅里叶变换法得到斯托罗哈数St。结果表明,倒角半径的增加改变了方柱的分离点,使得尾流区长度增加,旋涡尺度减小;Cd和Cl的振动幅值呈现先减小后增大的趋势,倒角半径为0.1D和0.2D时方柱受力较小,不存在倒角时方柱受力较大,倒角半径为0.3D时方柱受力最大;随着倒角半径的增加,柱体截面形式越接近圆形,斯托罗哈数逐渐增大,漩涡脱落频率更快。 相似文献
3.
基于有限体积法求解二维粘性不可压缩Navier-Stokes方程,分别采用层流模型和Realizable k-ε模型研究Re=250和Re=104前置平板与下游方柱间的流动干扰现象,分析不同尺度的平板布置在不同位置时对下游方柱的绕流场及流体动力性能的影响。计算发现在方柱上游布置平板可以有效的控制方柱的绕流场,减小方柱的阻力系数和升力系数;随着平板尺度的增加,方柱的阻力系数、升力系数呈下降趋势;并且存在较好的平板布置区间,可以最大程度的降低方柱和平板的阻力系数及方柱的升力系数,从而达到良好的减振、降噪的效果。 相似文献
4.
《中国海洋大学学报(自然科学版)》2016,(6)
为研究间距比对多柱体在湍流场下的互扰效应影响,利用Fluent软件模拟了雷诺数为3 900,柱间距比L/D为1.6~6.0情况下正方形排列四圆柱绕流过程。通过模拟得到了不同间距比下的升、阻力系数值以及涡量图,利用快速傅里叶变换法得到了漩涡脱落频率。结果表明,当柱间距比L/D为1.6~2时,4个圆柱后都没有漩涡脱落,随间距比增加,上游圆柱平均升力系数增大,平均阻力系数减小,下游圆柱平均升、阻力系数减小,斯特鲁哈数增大;当L/D为2~3.5时,随间距比增大,下游圆柱后开始出现漩涡脱落,平均升、阻力系数减小,斯特鲁哈数增大;当L/D为3.5~6时,随间距比增大,四个圆柱后都发生漩涡脱落,上游圆柱平均升、阻力系数减小,下游圆柱平均升力系数减小,平均阻力系数增大,斯特鲁哈数不变。L/D3.5时互扰效应逐渐增强,L/D3.5时互扰效应逐渐减弱;考虑到工程安全性和经济性,本文研究成果对于海洋工程设计具有一定的参考价值。 相似文献
5.
利用Fluent软件模拟雷诺数为200时不同间距比G/D和直径比d/D情况下的圆柱绕流现象。根据模拟结果分析G/D和d/D对圆柱体的涡脱落形态,大、小柱体的升力,阻力系数和St数的影响,结果表明涡脱落形态随着G/D和d/D的变化呈现不同的形式,在G/D小于临界间距比时呈现单一涡脱落形态,在G/D大于临界间距比时,呈现双旋涡脱落形态;临界间距比随着d/D增大而增大。在临界间距比附近大、小柱体的升力和阻力系数值及St数变化较大,大、小柱体的St数具有相同的变化规律,St随着d/D的增大而减小。 相似文献
6.
基于量纲分析,设计模型试验研究稳态海流作用下子母管结构的横向涡激振动。通过对结构横向振动位移、水动力载荷和流场速度的同步测量分析,研究子母管结构横向涡激振动幅值和频率随约减速度的变化规律以及母管的水动力特性。实验结果表明,子母管间距比和质量比对管道横向振动和水动力有较大影响。在管间距比为0.1～0.5范围内,子母管结构涡激振动存在明显的不对称性。随着子母管间距比的减小,结构横向最大振幅增大,涡激振动的约减速度范围变宽;随着质量比的增大,涡激振动的约减速度范围变窄。母管的平均阻力系数随子母管间距比的增大单调递减,而平均升力系数则呈现非单调变化的特征。 相似文献
7.
《中国海洋大学学报(自然科学版)》2015,(5)
多柱体系统在石油开采逐渐向深海发展的过程中得到广泛的应用,由于波浪、流对多柱体的影响易导致其破坏。因此研究多柱体系统绕流具有重大价值。目前多不等直径多柱体绕流的研究还有待深入。本文利用Fluent模拟雷诺数Re=3 900,G/D为0.1~2.5,d/D为0.5、1.0情况下并列双圆柱的绕流过程,并根据模拟结果分析G/D和d/D的变化对大、小柱体涡脱落形态、升力系数Cl、阻力系数Cd和St值的影响。结果表明,随着G/D变化,涡脱落形态会呈现出不同的形式,绕流参数值也随之发生变化。当0G/D≤0.2时,柱后只有一个涡脱落,为单一涡脱落区,升、阻力系数值存在突变,St值小于单柱St值;当0.2G/D≤0.5~1.0时,柱后出现交替的偏斜流,为偏斜流区,升、阻力系数随着G/D的增大而减小,St值在两个极值之间变化;当0.5~1.0G/D≤2.5时,柱后有成对的涡旋,为双旋涡脱落区,升阻力系数值趋于稳定,St值稳定在0.2左右。偏斜流区与双旋涡脱落区之间的临界间距比G/D随着d/D的增大而增大;不等直径情况下,间隙流偏斜对大柱的影响小于对小柱的影响。 相似文献
8.
9.
因为蝠鲼在运动时具有低噪声，机动性能好等优点，以蝠鲼作为仿生对象，结合动态网格技术， 通过对仿生蝠鲼的外形轮廓中某一截面进行流体动力分析，研究该截面轮廓在大变形情况下，不同频率、不同波长对周围流场特性的影响。仿真计算结果表明，在波长一定时，随着频率的升高，升力系数波动幅度变大，推力增大。在频率一定时，随着波长的增加，升力系数波动幅度变大，推力也增大。 相似文献
10.
两层粘性流体中圆柱体受迫振荡数值模拟 总被引：1，自引：1，他引：1
研究两层粘性流体中无限长水平圆柱体的受迫振荡问题。在湍流模式下,采用VOF方法追踪两层流体的内界面,基于动网格技术模拟圆柱体的运动边界,对均匀流中横向振荡圆柱体的绕流场进行了数值模拟。计算受迫振荡圆柱体的升力系数、阻力系数随时间的演化曲线和圆柱体的尾涡分布,以及圆柱体的受迫振荡激发两层流体内界面的扰动,并与均匀流体的情况进行了比较分析。研究表明,流体的两层分层效应对受迫振荡圆柱体的升阻力系数和尾涡分布特性都有显著影响,在水下输油气管道涡激振动特性的工程评估中,应考虑流体的密度分层效应。 相似文献
11.
The main purpose of this study is to establish a better understanding of the relationship between drag reduction and surface roughness. Experiments were conducted to measure the force and flow characteristics of a circular cylinder with different types of artificial surface roughness over the range 6 × 103 < Re < 8 × 104 (Re is based on the cylinder diameter D). The roughness cylinder was formed by covering the exterior surface of the cylinder with uniformly distributed (1) sandpaper, (2) netting, and (3) dimples. The roughness coefficient ranged from k/D = 0.0028 to 0.025 (k is the roughness height). A detailed quantitative measurement of the flow field around the cylinder using Particle Imaging Velocimetry (PIV) was carried out. The hydrodynamic force coefficients (drag and lift) of the rough cylinders are compared against those of a smooth cylinder measured under the same flow conditions. It is found that certain configuration of surface roughness significantly reduces the mean drag coefficient of the cylinder, particularly at large Reynolds numbers. In addition, the root-mean-square (r.m.s.) lift coefficient of the rough cylinders is considerably lower than that of a smooth cylinder. 相似文献
12.
A series of three-dimensional numerical simulations is carried out to investigate the effect of inclined angle on flow behavior behind two side-by-side inclined cylinders at low Reynolds number Re=100 and small spacing ratio T/D=1.5 (T is the center-to-center distance between two side-by-side cylinders, D is the diameter of cylinder). The instantaneous and time-averaged flow fields, force coefficients and Strouhal numbers are analyzed. Special attention is focused on the axial flow characteristics with variation of the inclined angle. The results show that the inclined angle has a significant effect on the gap flow behaviors behind two inclined cylinders. The vortex shedding behind two cylinders is suppressed with the increase of the inclined angle as well as the flip-flop gap flow. Moreover, the mean drag coefficient, root-mean-square lift coefficient and Strouhal numbers decrease monotonously with the increase of the inclined angle, which follows the independent principle at small inclined angles.
相似文献13.
Measurements are presented of the effects of corner radius on the hydrodynamic forces experienced by cylindrical bluff bodies in oscillatory flow over the Keulegan Carpenter number range from 1 to 100. The range of Reynolds number covered is from 200 to 2 × 104 and two basic cross-sectional shapes, namely a square and a diamond, were used in the investigation. Drag coefficients in oscillatory flow are found to be more sensitive to corner radius than in steady flow. At a fixed Keulegan Carpenter number the drag coefficient of a diamond section decreases with increasing corner radius and the reduction is more marked at low Keulegan Carpenter numbers. The drag of a square section does not follow a consistent trend with corner radius and for high Keulegan Carpenter numbers the rounded square with a corner radius of 0.265D (where D is the width of the model normal to the flow) can have a drag coefficient equal to half the value for a circular cylinder. 相似文献
14.
The unsteady flow past a circular cylinder which starts translating and transversely oscillating from rest in a viscous fluid is investigated at a Reynolds numbers of R=103 and at a Strouhal number of π/4 and for the maximum oscillatory to translational velocity ratios between 0.1 and 1.0. This study is based on numerical solutions of the two-dimensional unsteady Navier–Stokes equations. The object of the study is to examine the effect of increase of velocity ratio on the near-wake structure as well as the hydrodynamic forces acting on the cylinder. For all velocity rates a periodic structure of vortex evaluation and shedding develops which is repeated exactly as time advances. Vortex dynamics close behind the body are affected by changing acceleration of the cylinder and a changeover from one mode to a different mode of vortex formation is observed with increase in velocity ratio. A comparison of the present results with the impulsively started translating case has been included to illustrate the effect of velocity ratio on drag at small values of velocity ratio. 相似文献
15.
在一定来流条件下,张力腿平台(tension leg platform,简称TLP)的立柱后缘出现周期性的交替旋涡脱落,致使立柱受到垂直于来流方向的升力和平行于来流方向的阻力作用,导致TLP产生大幅度往复运动,显著增加平台结构和系泊系统的负载。目前,关于单柱、多柱结构绕流问题的研究较多,但对于TLP绕流特性的研究较少,机理尚存不明确的地方。为研究TLP的绕流力变化情况和流场特征,开展了数值模拟分析。利用计算流体动力学数值模拟软件,基于雷诺平均(RANS)法和分离涡模拟(DES)法对TLP绕流场进行仿真分析,揭示了TLP的绕流特性。结果表明,在3种来流角度和多个折合速度Vr下,TLP绕流的流体力系数存在明显差异,升力系数时域曲线呈现脉动性。TLP的上、下游立柱间存在明显的相互作用,影响了旋涡的形成与发展。TLP的旋涡脱落大多集中在平台固有频率附近,且在Vr=7,来流角度为0°时,升力系数频谱峰值最大,旋涡脱落集中。 相似文献
16.
The hydrodynamic forces on the stationary partially submerged cylinder are investigated through towing test with Reynolds number ranging from 5 × 104 to 9 × 105. Three test groups of partially submerged cylinders with submerged depths of 0.25 D, 0.50 D, and 0.75 D and one validation group of fully submerged cylinders are conducted. During the experiments, the hydrodynamic forces on the cylinders are measured using force sensors. The test results show a considerable difference in the hydrodynamic coefficients for the partially submerged cylinders versus the fully submerged cylinders. A significant mean downward lift force is first observed for the partially submerged cylinders in a steady flow. The maximum of the mean lift coefficients can reach 1.5. Two distinct features are observed due to the effects of overtopping: random distributions in the mean drag coefficients and a clear quadratic relationship between the mean lift coefficients and the Froude number appear in the non-overtopping region. However, the novel phenomenon of a good linear relationship with the Froude number for the mean hydrodynamic coefficients is clearly shown in the overtopping region. In addition, fluctuating hydrodynamic coefficients are further proposed and investigated. These results are helpful to have a better understanding of the problem and to improve related structural designs. 相似文献
18.
Influence of the turbulence intensity and turbulence length scale on the hydrodynamic characteristics and heat transfer of a circular cylinder, streamlined by a viscous fluid flow, is numerically studied. We take the Reynolds number of the oncoming flow equal to 4×104, the turbulence intensity Tuf and the dimensionless turbulence length scale Lf varying from 1.0% to 40% and from 0.25 to 4.0, respectively. We confirmed that the increase of Tuf leads to the suppression of the periodic vortex shedding from the cylinder surface, and as a result the stationary mode of streamlining is formed. Consequently, with the increasing turbulence intensity directly in front of the cylinder Tu*, the amplitude of the lift coefficient decreases monotonically. Nevertheless, the time-averaged drag coefficient of the streamlined cylinder decreases at Tu*<6.0%, and increases at Tu*>9.0%. The dependence of the average Nusselt number on Tu* is near-linear, and with the increasing turbulence intensity, the Nusselt number rises. However, the change of the average Nusselt number depending on Lf is non-monotonic and at Lf=1.0, the value reaches its maximum. 相似文献