共查询到20条相似文献，搜索用时 187 毫秒
1.
浮托安装法广泛应用于大型组块海上安装。导管架平台上部组块浮托安装进船过程中,风、浪、流引起的浮托驳船横向运动造成浮托驳船与导管架桩腿的碰撞,碰撞力可能会对导管架结构造成损伤。陆丰7-2上部组块浮托安装中,为了监测碰撞力大小,设计了碰撞力海上监测系统。通过在导管架外侧四个桩腿上安装光纤光栅应变传感器对碰撞过程中导管架桩腿进行应力监测,进而计算碰撞力。对碰撞过程,载荷作用位置、方向进行简化,并对载荷大小及垂向作用位置对计算的影响进行了研究。结构分析模型简化后,测点von-Mises应力与碰撞力大小成正比,对导管架整体结构建模计算并取局部结构计算比例系数,结合应力实测数据计算出进船过程中驳船对导管架桩腿碰撞力。 相似文献
2.
在时域内分析深水钢悬链立管在平台运动和波流载荷共同作用下的非线性动力响应;采用雨流计数法处理立管节点应力的时间历程,选用DoE.E型S-N曲线分析立管在单一海况和平台运动联合作用下的疲劳损伤;将各方向含概率分布的疲劳损伤进行叠加,得到立管整体的全方向疲劳损伤及疲劳寿命。平台的运动为六自由度的运动预报数据,波流载荷由某海域实际的波浪统计数据采用Morison公式计算所得。计算结果表明钢悬链立管疲劳寿命的极值点分别位于悬挂点附近和触地点附近,对立管疲劳寿命极值点各方向疲劳损伤分布情况进行了分析。所提方法为钢悬链立管疲劳分析提供了新思路,给出的结论对钢悬链立管设计分析有一定借鉴意义。 相似文献
3.
4.
冰激直立腿海洋平台疲劳寿命分析 总被引：1，自引：1，他引：0
由于渤海特殊环境条件与油藏分布决定了该海域导管架油气平台属于典型的柔性抗冰结构。多年现场观测发现,该类结构存在显著的冰激振动现象。冰振不仅能激起较大的甲板加速度响应,还会引起明显的导管架管节点交变应力。在结构设计与安全保障中进行疲劳分析及寿命估计是必要的。对于直立腿抗冰结构,精确的冰激疲劳寿命计算方法还不成熟。基于多年的现场监测,首先分析了冰与直立腿抗冰结构相互作用过程;其次,提出了冰激直立腿平台的疲劳寿命分析流程;最后,选取渤海某典型直立腿平台,利用ANSYS数值模拟,对比了稳态冰力和随机冰力下结构的疲劳损伤,进而计算出疲劳寿命。本研究为寒区柔性结构抗冰设计与安全保障提供了理论基础。 相似文献
5.
研究了在建阶段导管架圆管发生风致涡激振动对整体疲劳性能的影响。建立了圆管动力学模型，分析了圆管的动力学特性；固定系数取值0.7模拟实际工程中圆管两端的焊接约束形式，计算了圆管的振动响应；基于线性累积损伤准则和S-N曲线计算了圆管发生风致涡激振动的疲劳损伤度，并根据规范计算出圆管在位阶段的疲劳损伤度，对比总结风致涡激振动对总体疲劳性能的影响以及振动抑制措施对疲劳性能的改善。研究表明，在建阶段导管架圆管发生风致涡激振动会明显地影响圆管的疲劳特性，降低疲劳寿命，因此可以通过绑定绳索、安装防振锤等手段减少结构的疲劳损伤。 相似文献
6.
相较于传统的吊装法,浮托安装法是目前一种比较安全、经济、可靠的大型组块海上安装方法。本文对某平台上部组块的海上浮托安装进行了数值模拟,应用ANSYS-AQWA软件建立上部组块-驳船-系泊系统模型,在时域内对模型就位状态下的运动响应进行了耦合动力分析。重点研究了不同波浪工况下上部组块-驳船-系泊系统模型关键点的运动以及系泊张力的变化情况。研究结果对实际工程中应用浮托安装法施工具有重要的参考意义。 相似文献
7.
8.
以南海某平台组块海上拖航作业为例,阐述风险评估的基本流程;针对海上拖航过程提出一套具体、实用的风险辨识、事故树建立以及建立风险控制措施的方案;同时给出一种将风险因素定性计算予以量化的方法,即风险值计算方法,并且针对海油工程确定风险值标准. 相似文献
9.
非常规管节点疲劳寿命分析与计算 总被引：6，自引：1，他引：6
对非常规管节点的疲劳寿命进行了分析研究，用SESAM计算疲劳载荷，应用精细有限元分析计算热点应力，用规范的S—N曲线计算管节点的疲劳寿命。通过实例计算表明，这些处理对非常规管节点疲劳寿命分析与计算是很有效的。 相似文献
10.
11.
波浪作用下缆船拖带系统非线性运动数值模拟 总被引：1，自引：0，他引：1
基于船舶操纵性运动方程和拖缆的三维动力学运动方程,提出了被拖点位置匹配的方法,建立了拖船—拖缆—被拖船系统整体非线性拖带动力学模型。为了考察被拖船航向稳定性与横向稳性的关系以及波浪载荷作用的影响,被拖船采用水平面四自由度运动方程,并引入了波浪的作用力和力矩。拖船采用PD控制方法较真实地模拟了拖船航向改变的运动过程。对一个拖船—拖缆—被拖船系统(5 000 t的拖船和3 000 t的被拖船)在时域内进行了规则波浪作用下拖带运动的模拟,计算结果表明被拖带船舶在波浪中运动呈现运动稳定、不稳定和临界状态3种可能的特性。根据模拟计算结果,认为波浪中拖带航向稳定是被拖带船舶保持稳性的必要条件。 相似文献
12.
The behavior of a long cable towed at slow speeds through the ocean depends in a complex fashion on the path followed by the towing ship relative to the water. A cable simulation program was used to characterize the response of the cable by using idealized towing ship maneuvers as input to the program. The response of the cable was noted and it was found that the behavior of the cable was strongly dependent on the fundamental period of the towing vessel maneuvers. Sinusoidal deviations of the towing ship from a straight towing track resulted in delayed and reduced excursions of the towed vehicle from the tract; the estimated response ratio varied from 0·002 to 0·800, depending both on the period of the deviations (periods ranged from 5·5 to 4·0 hr) and on the towing depth (2 or 6 km). The ship's speed was 3 km/hr. The time lag between ship motion and vehicle response was approximately 0·5 hr for the shallow case and 1·3 hr for the deep case. Simulations runs of a low dragk (faired) cable showed that the behavior of the vehicle when towed at a depth of 6 km was similar to that obtained with a conventional cable at 2 km depth. The response of the towed vehicle to a right-angle turn of the towing ship was investigated and a generalized model of the response developed. The effects of a controllable side force on the towed vehicle were also simulated and it was noted that a deviation (2-hr period) of the towed vehicle from a straight-line track could be reduced from 40 to 2 m by impressing a side force on the vehicle with an average magnitude of 150 newtons (30 lb). 相似文献
13.
Based on the fundamental equation of flexible cable dynamics for a towed system, an easily solved mathematical model is set up in this paper by means of appropriate simplification. Several regular patterns of spatial motion of towed flexible cables in water are obtained through numerical simulation with the finite difference method, and then modification and verification by trial results at sea. A technical support is provided for the towing ship to maneuver properly when a flexible cable is towed. Furthermore, the relations between two towed flexible cables, which are towed simultaneously by a ship, are investigated. The results show that the ship towing two flexible cables is safe under the suggested arrangement of two winches for the towing system, and the coiling/uncoiling sequences of the cables as well as the suggested way of maneuvering. 相似文献
14.
Autonomous vehicles are being developed to replace the conventional, manned surface vehicles that tow mine hunting towed platforms. While a wide body of work exists that describes numerical models of towed systems, they usually include relatively simple models of the towed bodies and neglect the dynamics of the towing vehicle. For systems in which the mass of the towing vehicle is comparable to that of the towed vehicle, it becomes important to consider the dynamics of both vehicles. In this work, we describe the development of a numerical model that accurately captures the dynamics of these new mine hunting systems. We use a lumped mass approximation for the towcable and couple this model to non-linear numerical models of an autonomous surface vehicle and an actively controlled towfish. Within the dynamics models of the two vehicles, we include non-linear controllers to allow accurate maneuvering of the towed system. 相似文献
15.
An experimental set-up is developed and proved to be effective for laboratory study of an underwater towed system. The experimental technique gives a practical method for monitoring the kinematic and dynamic performance of an underwater towed system in a ship towing tank. Both the theoretical and experimental results in the investigation indicate that the hydrodynamic response of a towed vehicle to the wave induced motion of a towing ship can be significantly reduced by applying a two-part tow method. A comparison of the numerical and experimental results in the investigation demonstrates that the numerical simulation results are close to the experimental data, overall agreement between experimental and theoretical results is satisfactory. The results qualitatively verify the mathematical model of a two-part underwater towed system proposed by Wu and Chwang [Wu, J., Chwang, A.T., 2000. A hydrodynamic model of a two-part underwater towed system. Ocean Engineering 27 (5), 455–472]. 相似文献
16.
针对海洋测量水下拖曳设备位置确定问题,综合考虑拖缆受力、海流影响以及水下拖体的运动性质,建立了水下拖曳设备的位置计算模型,并仿真计算分析了测量船在不同航行状态下拖曳设备位置确定的规律,探讨了不同海流效应对拖曳设备位置确定的影响。仿真计算结果表明,在海洋动态环境作用下,拖缆各方向的偏移明显呈曲线形状,非简单几何运算所确定。测船各方向的运动均可对水下拖体的位置在相应方向产生一定影响,而水下拖体位置的变化量小于测船拖点位置的变化量。海流对水下拖曳设备定位可造成数米的偏差,需进行相应改正。建议可考虑采取船载式ADCP实时测流辅助水下拖曳设备定位的工作模式。 相似文献
17.
Experimental Study on Response Performance of VIV of A Flexible Riser
with Helical Strakes 总被引：1，自引：1，他引：0
Laboratory tests were conducted on a flexible riser with and without helical strakes. The aim of the present work is to further understand the response performance of the vortex induced vibration (VIV) for a riser with helical strakes. The experiment was accomplished in the towing tank and the relative current was simulated by towing a flexible riser in one direction. Based on the modal analysis method, the displacement responses can be obtained by the measured strain. The strakes with different heights are analyzed here, and the response parameters like strain response and displacement response are studied. The experimental results show that the in-line (IL) response is as important as the cross-flow (CF) response, however, many industrial analysis methods usually ignore the IL response due to VIV. The results also indicate that the response characteristics of a bare riser can be quite distinct from that of a riser with helical strakes, and the response performance depends on the geometry on the helical strakes closely. The fatigue damage is further discussed and the results show that the fatigue damage in the CF direction is of the same order as that in the IL direction for the bare riser. However, for the riser with helical strakes, the fatigue damage in the CF direction is much smaller than that in the IL direction. 相似文献
18.
《中国海洋工程》2015,(5)
Laboratory tests were conducted on a flexible riser with and without helical strakes. The aim of the present work is to further understand the response performance of the vortex induced vibration(VIV) for a riser with helical strakes. The experiment was accomplished in the towing tank and the relative current was simulated by towing a flexible riser in one direction. Based on the modal analysis method, the displacement responses can be obtained by the measured strain. The strakes with different heights are analyzed here, and the response parameters like strain response and displacement response are studied. The experimental results show that the in-line(IL) response is as important as the cross-flow(CF) response, however, many industrial analysis methods usually ignore the IL response due to VIV. The results also indicate that the response characteristics of a bare riser can be quite distinct from that of a riser with helical strakes, and the response performance depends on the geometry on the helical strakes closely. The fatigue damage is further discussed and the results show that the fatigue damage in the CF direction is of the same order as that in the IL direction for the bare riser. However, for the riser with helical strakes, the fatigue damage in the CF direction is much smaller than that in the IL direction. 相似文献
19.
20.
Low-frequency electromagnetic methods are used in geophysical exploration to detect the magnetic field distortion between a transmitter and receiver produced by locally conductive bodies. Both ground and airborne systems are in current use. It is possible to similarly conduct underwater geophysical exploration by using an underwater towed source of electromagnetic radiation and a receiving magnetic or electric field detector. The receiver can be towed on an auxiliary cable, mounted on a boom on the towing platform, or land based. An underwater towed electromagnetic source suitable for ocean-bottom exploration has been constructed, and its underwater propagation characteristics at low frequency have been studied. This underwater calibrated source (UCS) is 4 m long, weighs 383 kg in air, and can produce vertical and horizontal magnetic dipoles and a horizontal electric dipole. Powered by a current-feedback-controlled, high-power, modified sonar amplifier, the UCS can produce 9710 ampereturn.m2 of magnetic dipole or 200 A.m of electric dipole at 50 A at frequencies up to 200 Hz without significant attenuation from coil inductance. This paper concentrates on the mechanical, hydrodynamic, and magnetic design details of the UCS and the electrical system, consisting of the high-current drive power system and the shipboard monitoring system for attitude and depth detectors. 相似文献