共查询到18条相似文献，搜索用时 125 毫秒
1.
2.
低围压水平下砂的排水行为(英文) 总被引：2，自引：1，他引：2
采用干样沉降法制备样品 ,选用静三轴仪对松砂和密砂样在 10 k Pa至 10 0 k Pa的低围压下的排水行为进行了实验研究 ,并对实验结果作了橡皮膜校正 ,在围压为 10 k Pa的密砂实验中 ,轴向应力的校正值可达到 12 %。实验研究表明低围压下松砂的剪胀性非常明显 ,且存在剪应力极值 ;围压越低 ,松砂和密砂的剪应力极值越小 ,达到最大剪应力所对应的剪应变越小。同时还表明低围压范围内相对密度不同 ,砂的应力应变特性不同 ;此外 ,低围压下砂的内摩擦角高于高围压下的值 ,从而在工程上应重视低围压水平下砂土工程参数的合理选取 相似文献
3.
为研究深海能源土在负压开采过程中含气储层的力学特性,基于含气土赋存理论,提出一种能够控制含气量及气泡大小的制样方法,通过GDS标准应力路径三轴试验系统,开展深海能源土含气储层的固结排水试验研究,分析深海能源土在不同黏土含量及不同含气量下的力学响应规律。研究结果表明：围压变化对深海能源土含气储层的抗剪强度峰值大小影响显著,围压越大抗剪强度峰值越高;黏土含量是决定应力应变曲线变化趋势的关键影响因素,黏土含量越高试样抗剪强度越低,试样抵抗应变软化效应的能力越强;含气土比饱和土体承载能力更低,且承载能力随含气量的增大呈衰减趋势;黏土含量和含气量是深海能源土含气储层抗剪强度指标的重要影响因素,黏土含量、含气量越高,土体自身的总抗剪强度值越低。 相似文献
4.
开展了低围压条件下固结不排水振动三轴实验,对埕北海域重塑粉土振动孔压发展模型进行研究。低围压条件下粉土孔压随振次的发展曲线呈现两种形态,具体呈现何种形态与粉土轴向动应力和临界循环应力有关。对孔压数据进行了归一化处理,发现低围压条件下粉土孔压模型可以用指数函数进行拟合,且黏土含量并不影响孔压模型形式,只会影响a、b两个实验参数。孔压影响因素分析表明,少量黏粒含量的加入可以使粉土的孔压发展速度增大;振动频率对粉土孔压发展的影响也存在一个临界值,约0.2 Hz,当振动频率小于该值时,粉土孔压增长速度随频率的增加而减缓;当振动频率大于该值时,粉土孔压增长的速度随频率的增加而增大。 相似文献
5.
海洋粉质粘土在波浪荷载作用后的不排水抗剪强度衰化特性 总被引：3，自引：0，他引：3
通过对南海重塑粉质粘土土样的大量动三轴试验结果分析,得到此种土在波浪荷载作用后不捧水抗剪强度衰化同动载作用引起的动应变幅及平均累积孔压之间的相互关系和预估公式;并通过与超固结土样的静三轴剪切试验结果的比较,发现动、静三轴两种试验结果具有很好的吻合关系。建议可用超固结土样的静三轴剪切试验同时结合部分动三轴试验来预估土样在波浪荷载作用后不排水抗剪强度衰化与平均累积孔压之间的关系。 相似文献
6.
利用土工静力-动力液压三轴-扭转多功能剪切仪，针对饱和黏土，在不固结不排水（uu）条件下进行了应力控制式循环扭剪和竖向-扭转耦合试验，通过对试验结果的对比分析探讨了初始预剪应力和应力反向对应力-应变关系特性的影响。并阐述了不同循环应力模式下孔隙水压力发展特性。试验结果表明初始预剪应力对循环应力-应变关系的模式有明显的影响，当初始预剪应力较大且没有应力反向发生时，变形以累积效应为主，当初始剪应力为0时，变形以循环效应为主；不固结不排水条件下的循环孔隙水压力总是在围压附近波动，孔压的波动范围似乎随循环应力的增大而增大，但不具有孔压累积升高的特点。综合考虑剪切变形和正向偏差变形的共同效应，同时为了能够反映平均残余变形和循环变形的影响，建议了一个综合应变破坏标准的算式。进而通过利用试验数据与目前常用的应变标准比较，表明这种破坏标准具有普遍适用性和较好的稳定性，适用于判定各种应力条件下黏土试样破坏及其强度。 相似文献
7.
动荷载作用下海底粉土的孔压响应及其动强度 总被引：5，自引：0，他引：5
本文选用近海分布较广的粉土为研究对象 ,利用室内动三轴试验结果 ,找出动荷载作用下粉土的动应力应变关系 ,分析模拟波浪荷载作用下粉土中的孔压响应、临界循环次数 ,确定波浪作用下粉土的应力状态、破坏临界循环次数 ,判断不同深度处的粉土发生液化的可能性及发生液化所需要的时间 ;研究粉土在动荷载作用下的强度降低 ,为海上工程设计和施工提供科学依据。 相似文献
8.
作为一种常见的近海海底灾害地质现象,波致海床液化严重威胁着黄河三角洲地区海底工程设施的安全。粉质海床液化后,海底粉土的结构、物理和力学性质均发生了改变,研究该变化规律尤其是评估液化后海底粉土再次发生液化的可能性具有重要的理论意义和应用价值。本文利用室内动三轴仪对取自黄河三角洲已液化和未液化海底粉土开展了液化试验对比研究,讨论了已液化和未液化海底粉土在孔压增长模式和轴向动应变发展趋势方面的异同,对比分析了二者的液化势。研究结果表明:应变标准比孔压标准更适用于评估黄河三角洲地区海底粉土的液化势;孔压和动应变发展模式均表明与未液化粉土相比,已液化海底粉土再次发生液化的抗力有所提高;已液化和未液化海底粉土归一化孔压比ud/σ3与循环加载次数比N/Nf间相关关系可采用双曲线或指数函数模型进行定量化描述;未液化海底粉土的波致液化临界循环应力比约为0.20,已液化海底粉土的临界循环应力比约为0.35。研究成果有助于加深对海底粉土波致液化特性的认识,亦可为循环应力历史影响下的土体力学性质研究提供参考。 相似文献
9.
为探究相对密度和有效围压对饱和海砂力学特性的影响,利用GDS动态三轴试验仪,对广西北部湾地区海砂开展了一系列固结排水三轴剪切试验,分析了相对密度、有效围压对饱和海砂强度特征、体变特征、割线模量以及摩擦角的影响规律。结果表明：随着围压的减小或相对密度的增大,试样体积应变不断增大,而相对密度或有效围压的增加均会提高试样的峰值强度,有效围压与峰值强度之间呈现良好的线性增长关系。随着围压的减小或相对密度的增大,应力相对软化系数、剪胀系数均不断增大,且有效围压与应力相对软化系数、剪胀系数分别呈线性和半对数线性相关。割线模量随轴向应变的增加整体呈衰减趋势,各试验工况下轴向应变为5%时试样的割线模量相比于轴向应变0.164%衰减了80%~90%。饱和海砂的峰值摩擦角随相对密度的增加而增大,随有效围压的增大而减小,相对密度Dr为50%时有效围压σc为50 kPa对应的峰值摩擦角是σc为200 kPa的1.098倍。 相似文献
10.
循环荷载下粉土液化流动特性拖球试验研究 总被引：1，自引：1，他引：0
基于流体力学中的Stokes黏滞阻力理论,以振动台试验为基础,开发了一套测量液化过程中粉土流变特性的拖球试验装置。在铺有粉土海床的模型箱内埋设光滑小球,通过测量小球水平运动过程中所受阻力值的大小,计算粉土液化的表观动力黏度,分析粉土液化过程中的表观动力黏度与超孔压比之间的关系,以及液化后表观黏度与应变率的变化规律。试验结果表明,振动台试验下,孔隙压力表现为迅速上升,粉土迅速达到液化状态;振动过程对海床固结影响较大;粉土海床在未达到完全液化状态时（ru<1）,表观黏度随超孔压比增大而减小,在液化状态下（ru=1）,剪应力随应变率增大而减小,粉土呈现出剪切稀化的特点,为典型的非牛顿流体特征。 相似文献
11.
From this research, overconsolidated undrained and drained behaviors of specimens with high sand content were highly dilatant. According to the comparison results of laboratory tests, the deviator stresses of silty sand were greater than sandy silt due to high sand content under increasing OCRs, and both silty sand and sandy silt were presented strain softening tendency after failure under undrained loading. The pore water pressure increased with increasing fines content under increasing OCRs. Silty sand exhibited more dilatancy and increasing shear strength than sandy silt because pore water pressures of silty sand were lower than sandy silt under higher OCRs. In overconsolidated drained tests, silty sand is higher strength than sandy silt because silty sand has a lower volumetric strain and higher deviator stress than sandy silt under increasing OCRs. As the degree of overconsolidation increased, similar behaviors of silty sand and sandy silt observed that volumetric strain decreased to negative values due to dilatancy effect and low-cohesion under current effective confining pressures. 相似文献
12.
Mohammed Chemmam Mostefa Belkhatir Rachid Bouferra 《Marine Georesources & Geotechnology》2016,34(4):384-394
This article presents a laboratory study of static behavior of silty-sand soils. The objective of this laboratory investigation is to study the effect of initial confining pressures and fines content on the undrained shear strength (known as liquefaction resistance) response, pore pressure, and hydraulic conductivity of sand–silt mixtures. The triaxial tests were conducted on reconstituted saturated silty-sand samples at initial relative density Dr = 15% with fines content ranging from 0 to 50%. All the samples were subjected to a range of initial confining pressures (50, 100, and 200 kPa). The obtained results indicate that the presence of low plastic fines in sand–silt mixture leads to a more compressible soil fabric, and consequently to a significant loss in the soil resistance to liquefaction. The evaluation of the data indicates that the undrained shear strength can be correlated to fines content (Fc), inter-granular void ratio (eg), and excess of pore pressure (Δu). The undrained shear strength decreases with the decrease of saturated hydraulic conductivity and the increase of fines content for all confining pressures under consideration. There is a relatively high degree of correlation between the peak shear strength (qpeak) and the logarithm of the saturated hydraulic conductivity (ksat) for all confining pressures. 相似文献
13.
A stress path with continuous rotation of the principal stress direction and continuous alteration of amplitude of deviatoric stress difference under the interaction of wave and earthquake loading was proposed based on the characteristics of the stress path under wave and earthquake loading, respectively. Using a GDS dynamic hollow cylinder apparatus, a series of cyclic triaxial-torsional coupling shear tests were performed on Nanjing saturated fine sand via the stress path mentioned previously under different relative densities, effective initial confining pressures, plastic fines contents, and loading frequencies to study the development of excess pore water pressure (EPWP) of saturated sand under the interaction of wave and earthquake loading. It was found that the development of EPWP follows the trend of fast-steady-mutative-drastic, which is different from that under the cyclic triaxial test or wave loading. The number of cycles causing initial liquefaction (NL) of saturated sand increases remarkably with relative densities. However, the relationships between NL and effective initial confining pressures, plastic fines content, or loading frequencies are more complex. 相似文献
14.
The behaviors of granular material and influencing factors under complex dynamic loading are studied by more and more researchers with particle flow method. Only the strain-controlled loading has been generally used in the current study, although this method was not consistent with the practice of engineering in many situations. In this article, stress-controlled dynamic simulation tests were carried out with particle flow method, which were used to study the collapse characteristics of silt under mutation of principal stress orientation. The tests were performed by PFC2D. The simulation results and the laboratory real tests’ results had a high degree of similarity, particularly in the collapse strain and vibration times. It was very useful to forecast the silt's critical failure state. Based on the verification data, the effects of confining pressure and cyclic shear stress ratio on the collapse characteristics of silt were studied further. With the increase of cyclic shear stress ratio, the deviator strain amplitude increased and the required vibration times gradually reduced to achieve the same strain level. Under the same dynamic shear stress ratio and vibration times, the initial dynamic elastic modulus slightly increased with the increase of initial confining pressure, and the variation range of final collapse deviator strain was small. In the analysis of micro-structural evolution, the redistribution of internal stress of sample was revealed during cyclic loading. With the increase of vibration times, the development of distribution gradually stabilized, and then the high shear stress appeared in some connected regions. On that stage, the particle system developed to instability and failure. The PFC simulation results confirmed that the collapse state was the critical stage to trigger the liquefaction of silt. 相似文献
15.
Reza Rezvani 《Marine Georesources & Geotechnology》2020,38(2):238-249
AbstractDifferent types of geosynthetic reinforcements have been widely used for improving shear strength of soil materials in recent decades. In this study, two different calcareous soils reinforced by geotextile layers were evaluated by monotonic compression triaxial tests. The calcareous soils were obtained from Hormuz Island and Boushehr Port located in the north coast of the Persian Gulf. Different reconstituted samples were prepared at dense conditions with and without geotextile layers and consolidated under different effective confining pressures ranging from 100 to 600?kPa. Different layers of reinforcements including one, two and three geotextile layers were placed in the reinforced samples and sheared under drained condition. The results show that confining pressure has a significant effect on the efficiency of reinforcements. Evidently, increasing the reinforcement layers decreased the particle breakage of the calcareous soils used in this study. 相似文献
16.
A testing program was initiated to determine the stress-strain and strength behavior of two very different marine sands (a calcareous sediment from South Australia and a siliceous sediment from the United Kingdom) at elevated confining pressures. The testing matrix consisted of a series of isotropically consolidated, undrained (CIU) and drained (CID), triaxial compression tests on samples of naturally deposited calcareous and siliceous sediment and remolded calcareous sediment. It was found that the calcareous samples displayed little cemented behavior during shear. For tests conducted at pressures up to 1.5 MPa, a significant amount of particle crushing occurred in the calcareous samples but not in the siliceous samples. Particle degradation and reorientation facilitates transitions from dilative to contractive behavior with increases in confining stress. The calcareous sediment exhibited contractive behavior at confining pressures above approximately 500 kPa and the siliceous sediment remained dilative at stresses up to 1 MPa during undrained loading. Comparison with data collected by the University of Sydney (CID tests with confining pressures up to 60 MPa) showed that most of the variations in strength behavior occurred within the low stress range (up to 2 MPa) tests conducted at URI. This was evident in the friction angle data and in the reloading Young's modulus data. 相似文献
17.
Experiments on silt incipient motion under wave action were carried out.Under wave action,for different wave periods,water depths and bulk densities of silt,the shear stress or height of waves for incipient motion was determined,and a relation between the shear stress and bulk density of silt was established.Results indicate that the critical shear stress depends on the structure of the silt itself,related to the tightness between the grains(or bulk density).Exterior condition is only an external cause of silt incipient motion,and the critical shear stress for the incipient motion is the token of exterior condition. 相似文献