共查询到19条相似文献，搜索用时 109 毫秒
1.
为使防波堤同时具有良好的掩护效果和水体交换能力,提出了两种带有透浪通道的新型直立式防波堤。基于Fluent求解器建立了三维数值波浪水槽,通过与试验结果对比,验证了该数值水槽求解波浪与透空堤作用具有较高的精度。对两种防波堤在规则波作用下的透浪特性进行了研究,结果表明:透射系数K_t与透空率呈正线性相关,且可通过调整透浪通道间距,使相同透空率下K_t降低20%～30%。对同一结构,K_t随相对波长的增大而显著增大,但受相对波高的影响较小。在透空率大于0.16后,异型沉箱防波堤的消浪性能明显优于错位沉箱。基于数值计算结果,给出了以上两种透空堤波浪透射系数的经验公式。 相似文献
2.
以不同刚度硅胶圆杆群为概化植物模型,测定其抗弯弹性模量,通过波浪水槽实验,研究规则波在不同刚度植物杆群内的流速分布、紊动特征及不同刚度杆群的消浪效果。实验结果表明,当波浪通过柔性杆群时,受其摆动的影响,流速周期变化从单峰型逐渐转变成双峰型,杆群刚度越小形成的二次波峰越明显;不同刚度杆群内水体紊动强度变化显示,杆群刚度越大,造成杆群内水体的紊动强度越大;随着杆群抗弯弹性模量的增大,其消浪系数也增大,消浪系数的增长与材料的抗弯弹性模量值非线性关系,而是在某一弹性模量范围内,对消浪系数的影响较为敏感。 相似文献
3.
应用经CSPM法和黎曼解修正后的光滑粒子流体动力学(SPH)方法,建立了主动吸收无反射数值波浪水槽,研究波浪作用下多孔介质结构的水动力特性。流体运动控制方程采用N-S方程,多孔渗水结构内流体的运动控制方程考虑渗流力的影响。数值计算结果给出了水槽内不同位置测点的波面历时曲线和越浪量随时间变化曲线,并同试验结果和Philip Liu的数值计算结果进行了比较。并对一个波浪周期内斜坡堤多孔介质结构内外的速度场和压力分布进行了讨论分析。计算分析表明,数值计算波面较Philip Liu的计算结果与试验结果吻合更好。说明应用SPH方法建立的二维数学模型能够较好地模拟破碎波在多孔渗水斜坡上的爬坡和越浪。 相似文献
4.
《中国海洋大学学报(自然科学版)》2016,(12)
以Navier-Stokes方程为控制方程,使用VOF方法追踪自由液面,由连续性方程和动量方程推导出源函数。基于非线性波浪理论和UDF对FLUENT进行二次开发,在数值水槽的各个功能区将不同的源项添加到动量方程中,实现动量源造波和消波的功能。此法可以有效地消除波浪在水槽出流边界的反射及波浪遇到结构物后在入射边界形成的二次反射,从而得到稳定的波动场。本文将这种方法应用于直墙防波堤上波浪压力的数值模拟,分析了造波和消波的有效性,对直立式防波堤波浪力进行了数值研究。为了得到更精确的结果,采用结构化网格和非结构化网格相结合,在直墙防波堤附近使用三角形网格,在其他区域使用四边形结构化网格,为了较好地捕捉自由液面,在液面上下一个波高的范围内对网格进行加密。将计算结果与二阶stokes波理论解进行对比,该方法计算结果与理论解一致,表明该方法能够产生历时较长的稳定的非线性规则波浪,能够很好地吸收波浪遇到建筑物产生的反射波,可以有效消除建筑物反射波的影响,为实际工程方案的设计提供参考,有较高的实用价值。通过计算得到极端高水位,设计高水位,设计低水位时候的各个测点的最大正向波压力和最大负向波压力,并将计算结果与物理模型试验数据和经验公式结果进行对比,结果吻合较好。并且由于该数值方法可以考虑防波堤迎浪面不同倾角的工况,其适应范围比经验公式范围更广,因此可以为海岸结构设计提供依据。 相似文献
5.
基于计算流体力学软件的三维数值模拟技术,分析了碟形越浪式波能发电装置的越浪性能,通过构建基于水气两相VOF(Volume of Fluid)模型的三维数值波浪水槽对该装置进行三维数值模拟研究,数值计算结果与物理试验结果相互对比验证较为吻合,验证了所构建的三维数值波浪水槽的可靠性,通过考察装置的坡度、导流叶片个数、干舷高度对越浪性能的影响确定装置的最优结构参数。结果表明,在装置的斜坡面边缘增加回流板可减少波浪的反射,提高装置的越浪性能。在数值模拟中将装置的斜坡面边缘处安装回流板对碟形越浪式波能发电装置参数进行优化,通过分析回流板的长度对装置越浪性能的影响来探索最优回流板长度。 相似文献
6.
7.
8.
带有弹簧支撑的水平板结构，可在波浪作用下起伏运动进行消浪，作为防波堤具有广泛的应用前景，但如何设计支撑刚度仍是当前研究的重点课题。基于黏性流理论建立数值波浪水槽，开展规则波与起伏板防波堤相互作用的模拟，得到起伏板透反射系数随支撑刚度的变化曲线，并分析最小透射系数对应刚度下起伏板运动相位对消浪的影响。为快速得到最小透射系数对应的支撑刚度，根据弹簧—阻尼—质量模型，建立一种以运动相位为输入反推起伏板最优支撑刚度的计算方法，并将推导结果与数值结果进行比较。结果表明，该方法推导的最优支撑刚度值与数值最优值接近，且可省去遍历取最优值的步骤，可为起伏板防波堤的支撑刚度设计提供参考。 相似文献
9.
10.
11.
Interstitial flows in breakwater cores and seabeds are a key consideration in coastal and marine engineering designs and have a direct impact on their structural safety.In this paper,a unified fully coupled model for wave?permeable breakwater?porous seabed interactions is built based on an improved N?S equation.A numerical wave flume is constructed,and numerical studies are carried out by applying the finite difference method.In combination with a physical model test,the accuracy of the numerical simulation results is verified by comparing the calculated and measured values of wave height at measurement points and the seepage pressure within the breakwater and seabed.On this basis,the characteristics of the surrounding wave field and the internal flow field of the pore structure,as well as the evolution process of the fluctuating pore water pressure inside the breakwater and seabed,are further analyzed.The spatial distribution of the maximum fluctuating pore water pressure in the breakwater is compared between two cases by considering whether the seabed is permeable,and then the effect of seabed permeability on the dynamic pore water pressure in the breakwater is clarified.This study attempts to provide a reference for breakwater design and the protection of nearby seabeds. 相似文献
12.
Numerical study for waves propagating over a porous seabed around a submerged permeable breakwater: PORO-WSSI II model 总被引：1，自引：0，他引：1
The phenomenon of the wave, seabed and structure interactions has attracted great attentions from coastal geotechnical engineers in recent years. Most previous investigations have based on individual approaches, which focused on either flow region or seabed domain. In this study, an integrated model (PORO-WSSI II), based on the Volume-Averaged/Reynolds-Averaged Navier-Stokes (VARANS) equations and Biot's poro-elastic theory, is developed to investigate the mechanism of the wave-permeable structure-porous seabed interactions. The new model is verified with the previous experimental data. Based on the present model, parametric studies have been carried out to investigate the influences of wave, soil and structure parameters on the wave-induced pore pressure. Numerical results indicated: (i) longer wave period and larger wave height will obviously induce a higher magnitude of pore pressure at the leading edge of a breakwater; (ii) after a full wave-structure interaction, the magnitude of pore pressure below the lee side of a breakwater decreases with an increasing structure porosity while it varies dramatically with a change of structure height; and (iii) the seabed thickness, soil permeability and the degree of saturation can also significantly affect the dynamic soil behaviour. 相似文献
13.
A numerical assessment study of tsunami attack on the rubble mound breakwater of Haydarpasa Port, located at the southern entrance of the Istanbul Bosphorus Strait in the Sea of Marmara, Turkey, is carried out in this study using a Volume-Averaged Reynolds-Averaged Navier-Stokes solver, IHFOAM, developed in OpenFOAM® environment. The numerical model is calibrated with and validated against the data from solitary wave and tsunami overflow experiments representing tsunami attack. Furthermore, attack of a potential tsunami near Haydarpasa Port is simulated to investigate effects of a more realistic tsunami that cannot be generated in a wave flume with the present state of the art technology. Discussions on practical engineering applications of this type of numerical modeling studies are given focusing on pressure distributions around the crown-wall of the rubble mound breakwater, and the forces acting on the single stone located behind the crown-wall at the rear side of the breakwater. Numerical modeling of stability/failure mechanism of the overall cross-section is studied throughout the paper.The present study shows that hydrodynamics along the wave flume and over the breakwater can be simulated properly for both solitary wave and tsunami overflow experiments. Stability of the overall cross-section can only be simulated qualitatively for solitary wave cases; on the other hand, the effect of the time elapsed during tsunami overflow cannot be reflected in the simulations using the present numerical tool. However, the stability of the overall cross-section under tsunami overflow is assessed by evaluating forces acting on the rear side armor unit supporting the crown-wall of the rubble mound breakwater as a practical engineering application in the present paper. Furthermore, two non-dimensional parameters are derived to discuss the stability of this armor unit; and thus, the stability condition of the overall cross-section. Approximate threshold values for these non-dimensional parameters are presented comparing experimental and numerical results as a starting point for engineers in practice. Finally, investigations on the solitary wave and tsunami overflow experiments/simulations are extended to the potential tsunami simulation in the scope of both representation of a realistic tsunami in a wave flume and stability of the rubble mound breakwater. 相似文献
14.
堤前远破波运动与冲淤形态 总被引：1，自引：0，他引：1
利用数值波浪水槽,对远破波作用下堤前波浪运动进行了数值模拟。分析了堤前速度场的变化,指出堤前波浪运动在一个波周期内可分为向堤波和离堤波。波浪在距堤约L/2处破碎后向堤冲击并沿堤面爬升,称为向堤波;波浪从堤面最高处回落与向堤波相遇并破碎,称为离堤波。堤前远破波的前半个周期的向堤波速度场大于后半个周期的离堤波速度场,且堤前波浪运动在一个波周期内的前半个周期和后半个周期完全不同。床面某点(L/4,3L/4)的速度在一个波浪周期内随时间呈向堤和离堤变化,向堤速度最大值大于离堤速度的最大值。利用堤前速度场的研究成果,进一步分析了远破波作用下堤前海床冲淤形成过程,完善了冲淤机理。 相似文献
15.
16.
E.V. Koutandos 《Ocean Engineering》2011,38(1):34-48
In the present study, wave interaction with a fixed, partially immersed breakwater of box type with a plate attached (impermeable-permeable) at the front part of the structure is investigated numerically and experimentally. The large scale laboratory experiments on the interaction of regular waves with the special breakwater were conducted in the wave flume of Laboratori d’Enginyeria Marνtima (LIM) at Universitat Politecnica de Catalunya (UPC) in Barcelona. Experimental results are compared with numerical results obtained with the use of the Cornell breaking Wave and Structures (COBRAS) wave model. The effects of an impermeable as well as a permeable plate attached to the bottom of the breakwater on its hydrodynamic characteristics (wave transmission, reflection, dissipation, velocity and turbulence kinetic energy) are investigated. Computed velocities and turbulence kinetic energy in the vicinity of the structure indicate the effects of the breakwater with the attached (impermeable/permeable) plate on the flow pattern and the turbulence structure. The attached impermeable plate at the front part of the breakwater enhances significantly the efficiency of the structure in attenuating the incident waves. The permeable plate reduces the efficiency of the structure since wave energy is transmitted through the porous body of the plate. Based on the hydrodynamic characteristics it is inferred that the breakwater with an impermeable plate attached to its bottom is more efficient. The comparison of horizontal and vertical forces acting on the breakwater for all cases examined reveals that plate porosity influences slightly vertical force and severely horizontal force acting on the structure, reducing maximum values in both cases. 相似文献
17.
The form of Boussinesq equation derived by Nwogu （1993） using velocity at an arbitrary distance and surface elevation as variables is used to simulate wave surface elevation changes. In the numerical experiment, water depth was divided into five layers with six layer interfaces to simulate velocity at each layer interface. Besides, a physical experiment was carried out to validate numerical model and study solitary wave propagation.“Water column collapsing”method （WCCM） was used to generate solitary wave. A series of wave gauges around an impervious breakwater were set-up in the flume to measure the solitary wave shoaling, run-up, and breaking processes. The results show that the measured data and simulated data are in good agreement. Moreover, simulated and measured surface elevations were analyzed by the wavelet transform method. It shows that different wave frequencies stratified in the wavelet amplitude spectrum. Finally, horizontal and vertical velocities of each layer interface were analyzed in the process of solitary wave propagation through submerged breakwater. 相似文献
18.
This paper presents results obtained from a series of experiments conducted in wave flume to assess the influence of the offshore low-crested breakwater as a defence structure in reducing the wave forces on vertical seawall. The main aim of the tests was to know the effect of crest elevation of the offshore low-crested breakwater as a rehabilitation structure for the existing damaged shore protection structures. In this study five relative breakwater heights are used and associated flow evolution was analyzed. With the sections proposed in this study, it is possible to achieve considerable reduction of wave force on the seawall. Modification factor is proposed to estimate the shoreward force on the seawall defenced by low-crested breakwater. 相似文献
19.
To find a simple, inexpensive, and effective type of floating breakwater for deep-sea aquaculture, we studied three types of structures: the single box, the double box, and the board net. We conducted two-dimensional physical model tests in a wave-current flume in the laboratory to measure the wave transmission coefficients of the three types of breakwaters under regular waves with or without currents. Based on the initial comparison of the wave transmission coefficients, we proposed the use of the board-net floating breakwater for use with fish cages; we then conducted detailed experiments to examine how wave transmission coefficients are affected by several factors, including the width of the board, the row number of the net, the rigidity of the board, and the current velocity. The experimental results show that the board-net floating breakwater, which is a simple and inexpensive type of structure, can effectively protect fish and fish cages and may be adopted for aquaculture engineering in deep-water regions. 相似文献