共查询到20条相似文献，搜索用时 62 毫秒
1.
平台在海上受风、浪、流、冰等水平载荷作用产生倾斜 ,而土壤粘接力、摩擦力和土抗力是平台的抗拔和抗倾力 ,桶基平台应满足抗拔、抗倾稳定的要求 ,以保证平台的整体稳定性。讨论了桶基平台受水平力作用时 ,桶形基础的破坏模式及其计算方法 ,阐述了抗倾稳定计算方法 相似文献
2.
《Ocean Modelling》2003,5(1):65-76
The errors introduced by asynchronous time stepping are analyzed. It is shown that asynchronous time stepping distorts the structure and the speed of the lowest mode. For typical time step ratios used in climate simulations, the lowest mode is no longer a strictly barotropic mode, and the associated wave is much slower than the barotropic Rossby waves in the oceans. As a result, seasonal cycles simulated in model runs based on asynchronous time stepping are severely contaminated. 相似文献
3.
Suction caisson foundation derives most of their uplift resistance from passive suction developed during the pullout movement. It was observed that the passive suction generated in soil at the bottom of the caisson and the failure mode of suction caisson foundation subjecting pullout loading behaves as a reverse compression failure mechanism.The upper bound theorems have been proved to be a powerful method to find the critical failure mechanism and critical load associated with foundations, buried caissons and other geotechnical structures. However, limited attempts have been reported to estimate the uplift bearing capacity of the suction caisson foundation using the upper bound solution. In this paper, both reverse failure mechanisms from Prandtl and Hill were adopted as the failure mechanisms for the computation of the uplift bearing capacity of the suction caisson. New equations were proposed based on both failure mechanisms to estimate the pullout capacity of the suction caisson. The proposed equations were verified by the test results and experimental data from published literature. And the two solutions agree reasonably well with the other test results. It can be proved that both failure mechanisms are reasonably and more consistent with the actual force condition. 相似文献
4.
This paper investigates the static pullout resistance of anchor chains embedded into cohesionless soil. The anchor chains, which are made of steel, were buried into Jumunjin sand whose relative density was set to approximately 60%. The anchor chains were horizontally pulled out through a displacement of 70?mm in laboratory model tests. Three different embedment depths and seven different numbers of chain links were adopted. The pullout resistance of the anchor chains was found to increase with increasing embedment depth and the number of anchor chain links. The measured resistance was significantly higher than the calculated frictional resistance, implying that the passive resistance at the front of the anchor chain significantly contributes to the pullout resistance. The contribution of the passive resistance tends to decrease with increasing number of chain links. 相似文献
5.
Hui Hu 《Marine Georesources & Geotechnology》2020,38(3):332-348
AbstractResistance factors for load and resistance factor design (LRFD) of pullout limit state of both permanent and temporary soil nails are calibrated against a wide design space using the current Federal Highway Administration (FHWA) nail load and resistance models. The calculated resistance factors were shown to scatter broadly among design scenarios that differ in wall face batter, soil friction angle, nail ultimate bond strength, and surcharge live load. An important lesson learned from the analysis results is that the current practice of using a single resistance factor for LRFD of nail pullout limit state could not result in uniform reliabilities across different design scenarios. Simple artificial neural network (ANN) models were developed for computation of resistance factors. Design examples demonstrated the ability of the ANN models in providing resistance factors that yield satisfactory and consistent reliabilities in different nail pullout designs. 相似文献
6.
In the field of ocean engineering, a beginning has been made in the use of large‐sized suction anchors for safe anchoring of large compliant structures. Suction anchors derive most of their uplift resistance from passive suction developed during the pullout movement. This article describes a set of laboratory tests on model suction anchors of three different embedment ratios to estimate the pullout behavior of suction anchors in soft clays typical of Indian marine clays. Tests were conducted on model anchors installed in soil beds prepared at four different consistencies in a test tank. This study shows the influence of soil consistency and embedment ratio (L/D) on the pullout behavior of suction anchors and on the variation of suction pressure at the top of the soil plug. The test results reveal that the behavior of suction anchors is much better than the behavior of open‐ended anchors from the considerations of both capacity and deformation. The consistent development of suction inside the anchor top confirms the plug formation and significant breakout resistance in the form of suction‐induced reversed end bearing. The results are further analyzed in terms of suction breakout factors. Further, the effect of burial depth of suction anchor on pullout behavior is shown. 相似文献
7.
8.
A series of model tests were performed on steel- and Perspex-made suction caissons in saturated dense marine sand to explore installation and extraction behaviors. The extractions of the caisson were conducted by applying monotonic loading or by pumping water into the caisson. Responses of suction caissons to pullout rates, aspect ratios, and extraction manners were examined. Test results show that a cone-shaped subsidence region occurs around the suction caisson during the suction-assisted installation. The pullout bearing capacity of the suction caisson in sand is dominated by the loading rate and the loading manner. For the suction caisson subjected to monotonic loading, the maximum bearing capacity is reached at the pullout rate of about 20.0?mm/s. The mobilized vertical displacement corresponding to the pullout capacity increases with increasing the pullout rate. The passive suction beneath the suction caisson lid reaches the maximum value when the pullout bearing capacity is mobilized. In addition, during the suction caisson extracted by pumping water into the caisson, the maximum pore water pressure in the caisson is obtained under the displacement of approximately 0.04 times the caisson diameter. The absolute values of the maximum pore water pressures for the suction caissons approximately equal those of the maximum vertical resistances at the monotonic pullout rate of 5 mm/s. When the vertical displacements of the suction caissons with the aspect ratio of 1.0 and 2.0 reach 0.92 and 1.77 times the caisson diameter, respectively, the seepage failure occurs around the caissons. Using a scaling method, the test results can be used to predict the time length required for the prototype suction caisson to be extracted from the seabed. 相似文献
9.
Time-domain numerical simulation of ocean cable structures 总被引：2，自引：0，他引：2
This paper describes the numerical features of WHOI Cable, a computer program for analyzing the statics and dynamics of oceanographic cable structures. The governing equations include the effects of geometric and material nonlinearities, bending stiffness for seamless modeling of slack cables, and a model for the interaction of cable segments with the sea floor. The program uses the generalized-α time integration algorithm, adaptive time stepping, and adaptive spatial gridding to produce accurate, stable solutions for dynamic problems. The nonlinear solver uses adaptive relaxation to improve robustness for both static and dynamic problems. The program solves surface and subsurface single-point mooring problems, multi-leg and branched array systems, and towing and drifting problems. User specified forcing can include waves, currents, wind, and ship speed. 相似文献
10.
A series of 1 g model tests was conducted to investigate the accumulated vertical pullout displacement and unloading stiffness of bucket foundations embedded in dry and saturated sands. The foundations were subjected to vertical pullout cyclic loading with different load amplitudes. Cyclic load was applied up to 104 cycles. Test results showed that the accumulated vertical pullout displacement increased with the increase in the number of load cycles and cyclic load amplitudes. The unloading stiffness of the bucket foundations decreased with the increase in load amplitude and number of cycles. Empirical equations were proposed based on the test results to evaluate the accumulated vertical pullout displacement and unloading stiffness of the bucket foundations in saturated sand. These equations can be used for the preliminary design of single or tripod bucket foundations. 相似文献
11.
A series of model tests were conducted on Perspex-made suction caissons in saturated dense marine sand to study the sand plug formation during extraction. Suction caissons were extracted by pullout loading or by pumping air into the suction caisson. Effects of the pullout rates, aspect ratios and loading ways (monotonic or sustained) on the pullout capacity, and plug formation were investigated. It was found that the ultimate pullout capacity of the suction caisson increases with increasing the pullout rate. The sand plug formation under the pullout loading is significantly influenced by the pullout rate and the loading way. When the suction caisson is extracted at a relatively slow rate, the general sand boiling through the sand plug along the inner caisson wall occurs. On the contrary, the local sand boiling will occur at the bottom of the suction caisson subjected to a rapid monotonic loading or a sustained loading. Test results of the suction caisson extracted by pumping air into the caisson show that the pressure in the suction caisson almost follows a linear relationship with the upward displacement. The maximum pressures for suction caissons with aspect ratios of 1.0 and 2.0 during extraction by pumping air into the caisson are 1.70 and 2.27 times the maximum suction required to penetrate the suction caisson into sand. It was found that the sand plug moves downward during extraction by pumping air into the caisson and the variation in the sand plug height is mainly caused by the outflow of the sand particles from the inside of the suction caisson to the outside. When the suction caisson model is extracted under the pullout rate of 2?mm/s (0.28?mm/s for the prototype), the hydraulic gradient along the suction caisson wall increases to the maximum value with increasing the penetration depth and then reduces to zero. On the contrary, when extracted under the pullout rate of 10?mm/s (1.4?mm/s for the prototype), the hydraulic gradient along the suction caisson wall increases with increasing the pullout displacement. When extracted by pumping air into the caisson, the hydraulic gradient reaches the critical value, and at the same time, the seepage failure occurs around the suction caisson tip. 相似文献
12.
Plate anchors are extensively used in civil engineering constructions as they provide an economical alternative to gravity and other embedded anchors. The rate of loading is one of the important factors that affects the magnitude of soil resistance as well as soil suction force. This article outlines the effect of pullout rate on uplift behavior of plate anchors (70 mm diameter) buried in soft saturated clay by varying the pullout rate from 1.4 mm/min to 21.0 mm/min. The variation of breakout force and suction force with embedment depth and rate of pull are presented. A correlation between the rate of increase of undrained strength of clay and anchor capacity with rate of strain has been established. Finally an empirical equation has been proposed that includes the rate of pull in the estimation of breakout capacity of anchors. 相似文献
13.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
14.
An analytical solution has been developed to estimate the horizontal, vertical, and inclined loading pullout capacities of embedded suction anchors in sand. Validation of the analytical solution on pullout capacities has been made through comparisons with the centrifuge model test results. Primary variables for the centrifuge model tests are the depth to the loading point, the load inclination angle, and the addition of flanges. The results indicate that both the horizontal and vertical pullout capacities of the embedded suction anchor in sand increase, reach the peak and then start to decrease as the loading point moves downward. The inclined loading pullout capacity is very much dependent on the load inclination angle and the loading point. The effect of flanges on the pullout capacities is also found to be significant. 相似文献
15.
Plate anchors are extensively used in civil engineering constructions as they provide an economical alternative to gravity and other embedded anchors. The rate of loading is one of the important factors that affects the magnitude of soil resistance as well as soil suction force. This article outlines the effect of pullout rate on uplift behavior of plate anchors (70 mm diameter) buried in soft saturated clay by varying the pullout rate from 1.4 mm/min to 21.0 mm/min. The variation of breakout force and suction force with embedment depth and rate of pull are presented. A correlation between the rate of increase of undrained strength of clay and anchor capacity with rate of strain has been established. Finally an empirical equation has been proposed that includes the rate of pull in the estimation of breakout capacity of anchors. 相似文献
16.
Two adaptive algorithms for multipath time delay estimation 总被引：1，自引：0，他引：1
The problem of time delay estimation (TDE) with multipath transmissions arises often in many sonar and radar systems. Two adaptive algorithms based on a parameter estimation approach are proposed to estimate the difference in arrival times of a signal at two separated sensors in the presence of multipath propagation. The first method uses an adaptive IIR filter to eliminate the multipath signal in each transmission channel prior to applying a constrained delay estimation algorithm to extract the time difference between the two received outputs. The second employs two constrained adaptive FIR filters to perform equalization of the multipath arrivals, and time delay is then derived using a constrained delay estimator similar to that in the first method. Computer simulations are presented to compare and contrast the tracing capability and convergence behavior of these multipath TDE methods 相似文献
17.
Abstract The advanced piston cover (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
19.
This article reports the response of embedded circular plate anchors to varying frequencies of cyclic loading. The effects of time period of loading cycles and pre-loading on movement of anchors and post-cyclic monotonic pullout behavior are studied using a model circular (80 mm diameter) plate anchor, buried at embedment ratio of six in a soft saturated clay. The frequencies of loading cycles have showed considerable effect on movement of anchors. For given duration of loading, higher frequency cycles cause more movement of anchor than lower frequency cycles. Pre-loading reduces the movement of anchors in subsequent loading stages. When anchors are recycled at a load ratio level less than the pre-cycling load, the movement of anchor in recycling phase are very much reduced, but if the recycling is done at a higher load ratio level, the effect is not that much pronounced and the anchors behave as if they were not subjected to any cycling load in the past. Anchor subjected to cyclic loading and then monotonic pullout shows an increase in initial stiffness, whereas the peak pullout load was found to decrease marginally over that of an anchor not subjected to any cyclic loading. For the present test conditions, the relative post-cyclic stiffness of anchors is found to vary from 1.169 to 1.327. 相似文献
20.
This paper addresses the issue of the non conservation of tracer that occurs when a leapfrog time stepping scheme is used in association with a Robert-Asselin time filter within the framework of a time varying vertical coordinate system. A re-formulation of both the forcing and filtering terms that provides a globally conservative scheme is presented. Local conservation is then achieved when the model levels and subsequently the sea surface height satisfy a local compatibility condition. The properties of the resulting scheme are illustrated by a global coupled ocean–sea ice model based on the Nucleus for European Modelling of the Ocean (NEMO). 相似文献