共查询到20条相似文献，搜索用时 343 毫秒
1.
Composite Portland cement–basalt caprock cores with fractures, as well as neat Portland cement columns, were prepared to understand the geochemical and geomechanical effects on the integrity of wellbores with defects during geologic carbon sequestration. The samples were reacted with CO2–saturated groundwater at 50 °C and 10 MPa for 3 months under static conditions, while one cement–basalt core was subjected to mechanical stress at 2.7 MPa before the CO2 reaction. Micro-XRD and SEM–EDS data collected along the cement–basalt interface after 3-month reaction with CO2–saturated groundwater indicate that carbonation of cement matrix was extensive with the precipitation of calcite, aragonite, and vaterite, whereas the alteration of basalt caprock was minor. X-ray microtomography (XMT) provided three-dimensional (3-D) visualization of the opening and interconnection of cement fractures due to mechanical stress. Computational fluid dynamics (CFD) modeling further revealed that this stress led to the increase in fluid flow and hence permeability. After the CO2-reaction, XMT images displayed that calcium carbonate precipitation occurred extensively within the fractures in the cement matrix, but only partially along the fracture located at the cement–basalt interface. The 3-D visualization and CFD modeling also showed that the precipitation of calcium carbonate within the cement fractures after the CO2-reaction resulted in the disconnection of cement fractures and permeability decrease. The permeability calculated based on CFD modeling was in agreement with the experimentally determined permeability. This study demonstrates that XMT imaging coupled with CFD modeling represent a powerful tool to visualize and quantify fracture evolution and permeability change in geologic materials and to predict their behavior during geologic carbon sequestration or hydraulic fracturing for shale gas production and enhanced geothermal systems. 相似文献
2.
Hema J. Siriwardane Raj K. Gondle Duane H. Smith 《International Journal of Coal Geology》2009,77(1-2):188-202
Geologic sequestration in deep unmineable coal seams and enhanced coalbed methane production is a promising choice, economically and environmentally, to reduce anthropogenic gases such as carbon dioxide in the atmosphere. Unmineable coal seams are typically known to adsorb large amounts of carbon dioxide in comparison to the sizeable amounts of sorbed methane, which raises the potential for large scale sequestration projects. During the process of sequestration, carbon dioxide is injected into the coalbed and desorbed methane is produced. The coal matrix is believed to shrink when a gas is desorbed and swell when a gas is sorbed, sometimes causing profound changes in the cleat porosity and permeability of the coal seam. These changes may have significant impact on the reservoir performance. Therefore, it is necessary to understand the combined influence of swelling and shrinkage, and geomechanical properties including elastic modulus, cleat porosity, and permeability of the reservoir.The present paper deals with the influence of swelling and shrinkage on the reservoir performance, and the geomechanical response of the reservoir system during the process of geologic sequestration of carbon dioxide and enhanced coalbed methane production in an actual field project located in northern New Mexico. A three-dimensional swelling and shrinkage model was developed and implemented into an existing reservoir model to understand the influence of geomechanical parameters, as well as swelling and shrinkage properties, on the reservoir performance. Numerical results obtained from the modified simulator were compared to available measured values from that site and previous studies. Results show that swelling and shrinkage, and the combination of geomechanical and operational parameters, have a significant influence on the performance of the reservoir system. 相似文献
3.
Hydrated Portland cement was reacted with CO2 in supercritical, gaseous and aqueous phases to understand the potential cement alteration processes along the length of a wellbore, extending from a deep CO2 storage reservoir to the shallow subsurface during geologic carbon sequestration. The 3-D X-ray microtomography (XMT) images showed that the cement alteration was significantly more extensive with CO2-saturated synthetic groundwater than dry or wet supercritical CO2 at high P (10 MPa)-T (50 °C) conditions. Scanning electron microscopy with energy dispersive spectroscopy (SEM–EDS) analysis also exhibited a systematic Ca depletion and C enrichment in cement matrix exposed to CO2-saturated groundwater. Integrated XMT, XRD and SEM–EDS analyses identified the formation of an extensive carbonated zone filled with CaCO3(s), as well as a porous degradation front and an outermost silica-rich zone in cement after exposure to CO2-saturated groundwater. Cement alteration by CO2-saturated groundwater for 2–8 months overall decreased the porosity from 31% to 22% and the permeability by an order of magnitude. Cement alteration by dry or wet supercritical CO2 was slow and minor compared to CO2-saturated groundwater. A thin single carbonation zone was formed in cement after exposure to wet supercritical CO2 for 8 months or dry supercritical CO2 for 15 months. An extensive calcite coating was formed on the outside surface of a cement sample after exposure to wet gaseous CO2 for 1–3 months. The chemical–physical characterization of hydrated Portland cement after exposure to various phases of CO2 indicates that the extent of cement carbonation can be significantly heterogeneous depending on the CO2 phase present in the wellbore environment. Both experimental and geochemical modeling results suggest that wellbore cement exposure to supercritical, gaseous and aqueous phases of CO2 during geologic C sequestration is unlikely to damage the wellbore integrity because cement alteration by all phases of CO2 is dominated by carbonation reactions. This is consistent with previous field studies of wellbore cement with extensive carbonation after exposure to CO2 for three decades. However, XMT imaging indicates that preferential cement alteration by supercritical CO2 or CO2-saturated groundwater can occur along the cement–steel or cement–rock interfaces. This highlights the importance of further investigation of cement degradation along the interfaces of wellbore materials to ensure permanent geologic carbon storage. 相似文献
4.
Background
Reactive-transport simulation is a tool that is being used to estimate long-term trapping of CO2, and wellbore and cap rock integrity for geologic CO2 storage. We reacted end member components of a heterolithic sandstone and shale unit that forms the upper section of the In Salah Gas Project carbon storage reservoir in Krechba, Algeria with supercritical CO2, brine, and with/without cement at reservoir conditions to develop experimentally constrained geochemical models for use in reactive transport simulations.Results
We observe marked changes in solution composition when CO2 reacted with cement, sandstone, and shale components at reservoir conditions. The geochemical model for the reaction of sandstone and shale with CO2 and brine is a simple one in which albite, chlorite, illite and carbonate minerals partially dissolve and boehmite, smectite, and amorphous silica precipitate. The geochemical model for the wellbore environment is also fairly simple, in which alkaline cements and rock react with CO2-rich brines to form an Fe containing calcite, amorphous silica, smectite and boehmite or amorphous Al(OH)3.Conclusions
Our research shows that relatively simple geochemical models can describe the dominant reactions that are likely to occur when CO2 is stored in deep saline aquifers sealed with overlying shale cap rocks, as well as the dominant reactions for cement carbonation at the wellbore interface. 相似文献5.
Carbon dioxide (CO2) sequestration in depleted sandstone hydrocarbon reservoirs could be complicated by a number of geomechanical problems associated with well drilling, completions, and CO2 injection. The initial production of hydrocarbons (gas or oil) and the resulting pressure depletion as well as associated reduction in horizontal stresses (e.g., fracture gradient) narrow the operational drilling mud weight window, which could exacerbate wellbore instabilities while infill drilling. Well completions (casing, liners, etc.) may experience solids flowback to the injector wells when injection is interrupted due to CO2 supply or during required system maintenance. CO2 injection alters the pressure and temperature in the near wellbore region, which could cause fault reactivation or thermal fracturing. In addition, the injection pressure may exceed the maximum sustainable storage pressure, and cause fracturing and fault reactivation within the reservoirs or bounding formations. A systematic approach has been developed for geomechanical assessments for CO2 storage in depleted reservoirs. The approach requires a robust field geomechanical model with its components derived from drilling and production data as well as from wireline logs of historical wells. This approach is described in detail in this paper together with a recent study on a depleted gas field in the North Sea considered for CO2 sequestration. The particular case study shows that there is a limitation on maximum allowable well inclinations, 45° if aligning with the maximum horizontal stress direction and 65° if aligning with the minimum horizontal stress direction, beyond which wellbore failure would become critical while drilling. Evaluation of sanding risks indicates no sand control installations would be needed for injector wells. Fracturing and faulting assessments confirm that the fracturing pressure of caprock is significantly higher than the planned CO2 injection and storage pressures for an ideal case, in which the total field horizontal stresses increase with the reservoir re-pressurization in a manner opposite to their reduction with the reservoir depletion. However, as the most pessimistic case of assuming the total horizontal stresses staying the same over the CO2 injection, faulting could be reactivated on a fault with the least favorable geometry once the reservoir pressure reaches approximately 7.7 MPa. In addition, the initial CO2 injection could lead to a high risk that a fault with a cohesion of less than 5.1 MPa could be activated due to the significant effect of reduced temperature on the field stresses around the injection site. 相似文献
6.
In the context of carbon capture and storage, deep underground injection of CO2 induces the geomechanical changes within and around the injection zone and their impact on CO2 storage security should be evaluated. In this study, we conduct coupled multiphase fluid flow and geomechanical modeling to investigate such geomechanical changes, focusing on probabilistic analysis of injection-induced fracture reactivation (such as shear slip) that could lead to enhanced permeability and CO2 migration across otherwise low-permeability caprock formations. Fracture reactivation in terms of shear slip was analyzed by implicitly considering the fracture orientations generated using the Latin hypercube sampling method, in one case using published fracture statistics from a CO2 storage site. The analysis was conducted by a coupled multiphase fluid flow and geomechanical simulation to first calculate the three-dimensional stress evolution during a hypothetical CO2 injection operation and then evaluate the probability of shear slip considering the statistical fracture distribution and a Coulomb failure analysis. We evaluate the probability of shear slip at different points within the injection zone and in the caprock just above the injection zone and relate this to the potential for opening of new flow paths through the caprock. Our analysis showed that a reverse faulting stress field would be most favorable for avoiding fracture shear reactivation, but site-specific analyses will be required because of strong dependency of the local stress field and fracture orientations. 相似文献
7.
The sensitivity of coal permeability to the effective stress means that changes in stress as well as pore pressure within a coal seam lead to changes in permeability. In addition coal swells with gas adsorption and shrinks with desorption; these sorption strains impact on the coal stress state and thus the permeability. Therefore the consideration of gas migration in coal requires an appreciation of the coupled geomechanical behaviour. A number of approaches to representing coal permeability incorporate the geomechanical response and have found widespread use in reservoir simulation. However these approaches are based on two simplifying assumptions; uniaxial strain (i.e. zero strain in the horizontal plane) and constant vertical stress. This paper investigates the accuracy of these assumptions for reservoir simulation of enhanced coalbed methane through CO2 sequestration. A coupled simulation approach is used where the coalbed methane simulator SIMED II is coupled with the geomechanical model FLAC3D. This model is applied to three simulation case studies assembled from information presented in the literature. Two of these are for 100% CO2 injection, while the final example is where a flue gas (12.5% CO2 and 87.5% N2) is injected. It was found that the horizontal contrast in sorption strain within the coal seam caused by spatial differences in the total gas content leads to vertical stress variation. Thus the permeability calculated from the coupled simulation and that using an existing coal permeability model, the Shi–Durucan model, are significantly different; for the region in the vicinity of the production well the coupled permeability is greater than the Shi–Durucan model. In the vicinity of the injection well the permeability is less than that calculated using the Shi–Durucan model. This response is a function of the magnitude of the strain contrast within the seam and dissipates as these contrasts diminish. 相似文献
8.
This paper presents the development of a discrete fracture model of fully coupled compressible fluid flow, adsorption and geomechanics to investigate the dynamic behaviour of fractures in coal. The model is applied in the study of geological carbon dioxide sequestration and differs from the dual porosity model developed in our previous work, with fractures now represented explicitly using lower-dimensional interface elements. The model consists of the fracture-matrix fluid transport model, the matrix deformation model and the stress-strain model for fracture deformation. A sequential implicit numerical method based on Galerkin finite element is employed to numerically solve the coupled governing equations, and verification is completed using published solutions as benchmarks. To explore the dynamic behaviour of fractures for understanding the process of carbon sequestration in coal, the model is used to investigate the effects of gas injection pressure and composition, adsorption and matrix permeability on the dynamic behaviour of fractures. The numerical results indicate that injecting nonadsorbing gas causes a monotonic increase in fracture aperture; however, the evolution of fracture aperture due to gas adsorption is complex due to the swelling-induced transition from local swelling to macro swelling. The change of fracture aperture is mainly controlled by the normal stress acting on the fracture surface. The fracture aperture initially increases for smaller matrix permeability and then declines after reaching a maximum value. When the local swelling becomes global, fracture aperture starts to rebound. However, when the matrix permeability is larger, the fracture aperture decreases before recovering to a higher value and remaining constant. Gas mixtures containing more carbon dioxide lead to larger closure of fracture aperture compared with those containing more nitrogen. 相似文献
9.
An Approach for Modeling Rock Discontinuous Mechanical Behavior Under Multiphase Fluid Flow Conditions 总被引：1，自引：0，他引：1
Peng-Zhi Pan Jonny Rutqvist Xia-Ting Feng Fei Yan 《Rock Mechanics and Rock Engineering》2014,47(2):589-603
In this paper, the two computer codes TOUGH2 and RDCA (for “rock discontinuous cellular automaton”) are integrated for coupled hydromechanical analysis of multiphase fluid flow and discontinuous mechanical behavior in heterogeneous rock. TOUGH2 is a well-established code for geohydrological analysis involving multiphase, multicomponent fluid flow and heat transport; RDCA is a numerical model developed for simulating the nonlinear and discontinuous geomechanical behavior of rock. The RDCA incorporates the discontinuity of a fracture independently of the mesh, such that the fracture can be arbitrarily located within an element, while the fluid pressure calculated by TOUGH2 can be conveniently applied to fracture surfaces. We verify and demonstrate the coupled TOUGH–RDCA simulator by modeling a number of simulation examples related to coupled multiphase flow and geomechanical processes associated with the deep geological storage of carbon dioxide—including modeling of ground surface uplift, stress-dependent permeability, and the coupled multiphase flow and geomechanical behavior of fractures intersecting the caprock. 相似文献
10.
The integrity of wells, which are key components for CO2 sequestration, depends mainly on the seal between the wellbore cement and the geologic formation. To identify the reaction products that may alter the cement/caprock interface, batch experiments and computer modelling were conducted and analysed. Over time, the dissolution and precipitation of minerals alters the physical properties of the interface, including its tightness. One main objective of the simulation was thus to analyse the evolution of the porosity of cement and caprock over time. The alteration of the cement/caprock interface was identified as a complex problem and differentiated depending on rock type. The characteristic feature of a cement/shale contact zone is the occurrence of a highly carbonated, compacted layer within the shale, which in turn causes cement/shale detachment. In the case of a cement/anhydrite interface, the most important reaction is severe anhydrite dissolution. Secondary calcite precipitation takes place in deeper parts of the rock. The cement/rock contact zone is prone to rapid mineral dissolution, which contributes to increased porosity and may alter the well integrity. Comparison of computer simulations with autoclave experiments enabled the adjustment of unknown parameters. This enhances the knowledge of these particular assemblages. Overall, a good match was obtained between experiments and simulations, which enhances confidence in using models to predict longer-term evolution. 相似文献
11.
The lower Triassic/Bunter sandstone and lower Jurassic/Rhät formations of the Northern Germany sedimentary basin constitute feasible reservoirs for the storage of CO2 from combustion of fossil fuels or industrial production processes. This study presents analyses of geochemical interactions between CO2, formation fluid and rock of these potential reservoirs using geochemical modelling in order to assess the short and long term impact of CO2 sequestration. Batch equilibrium modelling was performed first for assessing the consistency of fluid and mineralogy field data and for identifying potential secondary minerals under the influence of injected CO2. Inclusion of reaction kinetics in the batch models allowed an observation of reaction paths and to estimate the time frame of geochemical reactions. Finally, one-dimensional equilibrium reactive transport modelling was used in order to investigate the direction of reactions under conditions of fluid flow and mass transport and to quantify feedbacks of reactions on transport processes.Results of the simulations performed show that dawsonite may act as the main CO2 storage mineral in both formations, while the carbonates calcite and dolomite dissolve over time. Also, changes in porosity and permeability are significant in the equilibrium reactive transport simulations. The time scale of kinetically controlled reactions observed in the kinetic batch modeling, however, suggests that CO2 mineral trapping in both formations requires very long time frames, and hence other mechanisms such as structural or solubility trapping seem to be more relevant within the injection or early post-injection phase for the studied formations. 相似文献
12.
Ian Cartwright 《Contributions to Mineralogy and Petrology》1997,129(2-3):198-208
Advection-dispersion fluid flow models implicitly assume that the infiltrating fluid flows through an already fluid-saturated
medium. However, whether rocks contain a fluid depends on their reaction history, and whether any initial fluid escapes. The
behaviour of different rocks may be illustrated using hypothetical marble compositions. Marbles with diverse chemistries (e.g.
calcite + dolomite + quartz) are relatively reactive, and will generally produce a fluid during heating. By contrast, marbles
with more restricted chemistries (e.g. calcite + quartz or calcite-only) may not. If the rock is not fluid bearing when fluid
infiltration commences, mineralogical reactions may produce a reaction-enhanced permeability in calcite + dolomite + quartz
or calcite + quartz, but not in calcite-only marbles. The permeability production controls the pattern of mineralogical, isotopic,
and geochemical resetting during fluid flow. Tracers retarded behind the mineralogical fronts will probably be reset as predicted
by the advection-dispersion models; however, tracers that are expected to be reset ahead of the mineralogical fronts cannot
progress beyond the permeability generating reaction. In the case of very unreactive lithologies (e.g. pure calcite marbles,
cherts, and quartzites), the first reaction to affect the rocks may be a metasomatic one ahead of which there is little pervasive
resetting of any tracer. Centimetre-scale layering may lead to the formation of self-perpetuating fluid channels in rocks
that are not fluid saturated due to the juxtaposition of reactants. Such layered rocks may show patterns of mineralogical
resetting that are not predicted by advection-dispersion models. Patterns of mineralogical and isotopic resetting in marbles
from a number of terrains, for example: Chillagoe, Marulan South, Reynolds Range (Australia); Adirondack Mountains, Old Woman
Mountains, Notch Peak (USA); and Stephen Cross Quarry (Canada) vary as predicted by these models.
Received: 3 February 1997 / Accepted: 26 June 1997 相似文献
13.
《Applied Geochemistry》2003,18(10):1555-1571
In the context of the proposed low- and intermediate-level radioactive waste repository at Wellenberg (Switzerland), calculations simulating the interaction between hyperalkaline solutions and a fractured marl, at 25 °C, have been performed. The aim of these calculations is to evaluate the possible effects of mineral dissolution and precipitation on porosity and permeability changes in such a fractured marl, and their impact on repository performance. Solute transport and chemical reaction are considered in both a high-permeability zone (fracture), where advection is important, and the wall rock, where diffusion is the dominant transport mechanism. The mineral reactions are promoted by the interaction between hyperalkaline solutions derived from the degradation of cement (a major component of the engineered barrier system in the repository) and the host rock. Both diffusive/dispersive and advective solute transport are taken into account in the calculations. Mineral reactions are described by kinetic rate laws. The fluid flow system under consideration is a two-dimensional porous medium (marl, 1% porosity), with a high-permeability zone simulating a fracture (10% porosity) crossing the domain. The dimensions of the domain are 6 m per 1 m, and the fracture width is 10 cm. The fluid flow field is updated during the course of the simulations. Permeabilities are updated according to Kozeny's equation. The composition of the solutions entering the domain is derived from modeling studies of the degradation of cement under the conditions at the proposed underground repository at Wellenberg. Two different cases have been considered in the calculations. These 2 cases are representative of 2 different stages in the process of degradation of cement (pH 13.5 and pH 12.5). In both cases, the flow velocity in the fracture diminishes with time, due to a decrease in porosity. This decrease in porosity is caused by the precipitation of calcite (replacement of dolomite by calcite) and other secondary minerals (brucite, sepiolite, analcime, natrolite, tobermorite). However, the decrease in porosity and flow velocity is much more pronounced in the lower pH case. The extent of the zone of mineral alteration along the fracture is also much more limited in the lower pH case. The reduction of porosity in the fractures would be highly beneficial for repository performance, since it would mean that the solutions coming from the repository and potentially carrying radionuclides in solution would have to flow through low-conductive rock before they would be able to get to higher-conductive features. The biggest uncertainty in the reaction rates used in the calculations arises from the surface areas of the primary minerals. Additional calculations making use of smaller surface areas have also been performed. The results show that the smaller surface areas (and therefore smaller reaction rates) result in a smaller reactivity of the system and smaller porosity changes. 相似文献
14.
Onset of Hydraulic Fracture Initiation Monitored by Acoustic Emission and Volumetric Deformation Measurements 总被引：2，自引：1，他引：1
Sergey Stanchits Aniket Surdi Patrick Gathogo Eric Edelman Roberto Suarez-Rivera 《Rock Mechanics and Rock Engineering》2014,47(5):1521-1532
In this paper, the results of laboratory studies of fracture initiation, early propagation and breakdown are reported. Three experiments were conducted on a low permeability sandstone block, loaded in a polyaxial test frame, to representative effective in situ stress conditions. The blocks were instrumented with acoustic emission (AE) and volumetric deformation sensors. In two experiments, fluids of different viscosity were injected into the wellbore, fluid injection was interrupted soon after the breakdown pressure had been reached. This allowed us to investigate hydraulic fracture initiation. In the third test, fracture initiation criteria were applied to stop hydraulic fracture propagation significantly earlier, prior to breakdown, and as it propagated a short distance from the wellbore. The analysis of AE results shows an increase in AE activity and a change in the AE spatial correlation, during the fracture initiation. This early stage of fracturing correlates strongly with the onset of rock volumetric deformation, and is confirmed by the analysis of ultrasonic transmission monitoring. The rock microstructure, after the test, was investigated by analysis of scanning electron microscope images. These indicated the development of leak-off zone near the wellbore and a dry hydraulic fracture at the farther distance from the wellbore. 相似文献
15.
Dedong Li Sebastian Bauer Katharina Benisch Bastian Graupner Christof Beyer 《Acta Geotechnica》2014,9(1):67-79
Sequestration of CO2 into a deep geological reservoir causes a complex interaction of different processes such as multiphase flow, phase transition, multicomponent transport, and geochemical reactions between dissolved CO2 and the mineral matrix of the porous medium. A prognosis of the reservoir behaviour and the feedback from large-scale geochemical alterations require efficient process-based numerical models. For this purpose, the multiphase flow and multicomponent transport code OpenGeoSys-Eclipse have been coupled to the geochemical model ChemApp. The newly developed coupled simulator was successfully verified for correctness and accuracy of the implemented reaction module by benchmarking tests. The code was then applied to assess the impact of geochemical reactions during CO2 sequestration at a hypothetical but typical Bunter sandstone formation in the Northern German Basin. Injection and spreading of 1.48 × 107 t of CO2 in an anticline structure of the reservoir were simulated over a period of 20 years of injection plus 80 years of post-injection time. Equilibrium geochemical calculations performed by ChemApp show only a low reactivity to the geochemical system. The increased acidity of the aqueous solution results in dissolution of small amounts of calcite, anhydrite, and quartz. Geochemical alterations of the mineral phase composition result in slight increases in porosity and permeability, which locally may reach up to +0.02 and 0.1 %, respectively. 相似文献
16.
Review: Thermal water resources in carbonate rock aquifers 总被引：3，自引：1，他引：2
Nico Goldscheider Judit Mádl-Szőnyi Anita Erőss Eva Schill 《Hydrogeology Journal》2010,18(6):1303-1318
The current knowledge on thermal water resources in carbonate rock aquifers is presented in this review, which also discusses geochemical processes that create reservoir porosity and different types of utilisations of these resources such as thermal baths, geothermal energy and carbon dioxide (CO2) sequestration. Carbonate aquifers probably constitute the most important thermal water resources outside of volcanic areas. Several processes contribute to the creation of porosity, summarised under the term hypogenic (or hypogene) speleogenesis, including retrograde calcite solubility, mixing corrosion induced by cross-formational flow, and dissolution by geogenic acids from deep sources. Thermal and mineral waters from karst aquifers supply spas all over the world such as the famous bath in Budapest, Hungary. Geothermal installations use these resources for electricity production, district heating or other purposes, with low CO2 emissions and land consumption, e.g. Germany’s largest geothermal power plant at Unterhaching near Munich. Regional fault and fracture zones are often the most productive zones, but are sometimes difficult to locate, resulting in a relatively high exploration uncertainty. Geothermal installations in deep carbonate rocks could also be used for CO2 sequestration (carbonate dissolution would partly neutralise this gas and increase reservoir porosity). The use of geothermal installations to this end should be further investigated. 相似文献
17.
深部煤层CO2地质封存与CH4强化开采(CO2–ECBM)技术在提高煤层气采收率的同时可实现碳减排,具有能源和环境双重效益。超临界CO2(ScCO2)、水和煤层顶板之间的地球化学反应可改变其物理力学性质,增加CO2泄漏的风险。以沁水盆地胡底煤矿3号煤层顶板岩石为研究对象,开展“ScCO2–水–岩”地球化学反应模拟实验,探讨CO2煤层封存条件下ScCO2–水–顶板岩样地球化学反应过程及其对岩石纵波速度和力学性质的影响。结果表明:ScCO2–水–岩之间化学溶蚀反应造成岩样Ca、Mg元素显著降低,促使岩样表面形成孤立状溶蚀孔,并随着反应时间的持续,进而形成大量的“溶蚀坑”和“溶蚀缝”;增加了岩样结构不连续性,使得声波传播路径增大、能量损失加剧,导致纵波波速降低;ScCO2–水–岩反应后岩样的峰值强度和弹性模量降低,泊松比升高,且三者之间的变化率与反应时间之间呈现Logistic函数的变化关系。对于胡底煤矿而言,ScCO2–水–岩反应过程中顶板力学性质的弱化不足以造成盖层的破裂和CO2泄漏,但在评价煤层CO2封存安全性时,还应考虑煤层吸附膨胀应力对顶板的影响。 相似文献
18.
David Savage Josep M. SolerKohei Yamaguchi Colin WalkerAkira Honda Manabu InagakiClaire Watson James WilsonSteven Benbow Irina GausJoerg Rueedi 《Applied Geochemistry》2011,26(7):1138-1152
The use of cement and concrete as fracture grouting or as tunnel seals in a geological disposal facility for radioactive wastes creates potential issues concerning chemical reactivity. From a long-term safety perspective, it is desirable to be able model these interactions and changes quantitatively. The ‘Long-term Cement Studies’ (LCS) project was formulated with an emphasis on in situ field experiments with more realistic boundary conditions and longer time scales compared with former experiments. As part of the project programme, a modelling inter-comparison has been conducted, involving the modelling of two experiments describing cement hydration on one hand and cement-rock reaction on the other, with teams representing the NDA (UK), Posiva (Finland), and JAEA (Japan).This modelling exercise showed that the dominant reaction pathways in the two experiments are fairly well understood and are consistent between the different modelling teams, although significant differences existed amongst the precise parameterisation (e.g. reactive surface areas, dependences of rate upon pH, types of secondary minerals), and in some instances, processes (e.g. partition of alkali elements between solids and liquid during cement hydration; kinetic models of cement hydration). It was not conclusive if certain processes such as surface complexation (preferred by some modellers, but not by others) played a role in the cement-rock experiment or not. These processes appear to be more relevant at early times in the experiment and the evolution at longer timescales was not affected. The observed permeability profile with time could not be matched. The fact that no secondary minerals could be observed and that the precipitated mass calculated during the simulations is minor might suggest that the permeability reduction does not have a chemical origin, although a small amount of precipitates at pore throats could have a large impact on permeability.The modelling exercises showed that there is an interest in keeping the numerical models as simple as possible and trying to obtain a reasonable fit with a minimum of processes, minerals and parameters. However, up-scaling processes and model parameterisation to the timescales appropriate to repository safety assessment are of considerable concern. Future modelling exercises of this type should focus on a suitable natural or industrial analogue that might aid assessing mineral-fluid reactions at these longer timescales. 相似文献
19.
Xu Zijuan Zuo Xinxin Fan Bailing Ding Xinquan Zhang Xiaodong Li Zichuan Yan Cuixiang Song Zhaoliang 《地球科学进展》2017,32(2):151-159
Phytoliths, also called amorphous silica particles, have a great geochemical stability and could occlude a certain amount of organic carbon during the forming process. At present, phytolith-occluded carbon (PhytOC) is recognized as one of long-term stable carbon sequestration mechanisms and has significant influence on regulating global climate change. At the same time, PhytOC isotope research has great value for paleo-environment, paleo-climate reconstruction and other fields. Therefore, more scholars pay attention to the PhytOC geochemical research. Based on the current research status, we summarized the current state of understading about phytolith forming process, elemental composition, geochemical stability, PhytOC sink and PhytOC isotope application for paleo-environment reconstruction. We also summarized the main problems of geochemical research on phytolith and PhytOC, which will make great contribution to further research on phytolith geochemical research. 相似文献
