共查询到20条相似文献，搜索用时 140 毫秒
1.
《吉林大学学报(地球科学版)》2015,(Z1)
激光剥蚀电感耦合等离子体质谱(LA-ICP-MS)技术广泛用来测量固体样品中的微量元素及同位素比值。然而在缺乏基体匹配校准条件下,发生在激光剥蚀过程中的元素分馏效应使得通常采用外标结合内标的方法很难准确量化待测元素的含量。不同岩石/矿物材料自身密度、表面张力、内部结构、元素成分等物理特性不同,对同一波长激光的吸收系数、反射系数、消光长度不同,导致相同实验条件下的激光对不同岩石/矿物剥蚀速率不同、剥蚀物体积不同、剥蚀后形成气溶胶粒子总数及粒径分布规律不同、在ICP中粒子化程度和效率也不同,最终待测元素分馏效应不同。建立了聚焦脉冲激光剥蚀不同基体材料动态物理模型,理论分析了激光脉冲宽度和能量密度对剥蚀速率影响的物理机制。采用193 nm波长的脉冲激光剥蚀不同地质标样NIST 614、NIST612、NIST610、BHVO-2G、BIR-1G、BCR-2G、橄榄石、石榴石、锆石。激光脉宽15 ns、束斑直径60μm、能量60 m J、频率8 Hz,脉冲数分别为25,50,100,150,200个,线性拟合后直线斜率值分别为0.140 44,0.138 05,0.124 13,0.099 11,0.093 87,0.105 39,0.113 86,0.051 22,0.09 341。实验结果表明,相同参数激光剥蚀不同基体时剥蚀速率(深度/脉冲个数)不同,玻璃标样比其它样品更易剥蚀。5 J/cm2能量条件下,平均剥蚀速率分别为169,159,155,118,104,116,115,62,88 nm/pulse;可见随着激光能量密度增加剥蚀速率缓慢增大,NIST614玻璃和石榴石剥蚀速率分别达到最大和最小。激光剥蚀地质样品剥蚀速率变化规律对理解剥蚀速率对元素分馏效应的影响、约束及校正具有理论意义和实践运用价值。 相似文献
2.
3.
4.
激光能量密度对LA-ICP-MS分析数据质量的影响研究 总被引：3，自引：2，他引：1
LA-ICP-MS分析矿物元素含量时激光能量密度会影响样品的剥蚀速率,从而影响测试过程的信号强度。激光能量密度变化对测试数据精确度的影响,以及不同天然矿物对激光能量密度的响应尚需进一步明确。本文测定了不同莫氏硬度天然矿物可稳定剥蚀的最小激光能量密度,评估了193nm ArF准分子激光系统中能量密度对地质标准样品(NIST SRM614、USGS BCR-2G、USGS GSC-1G)和天然矿物测试数据质量的影响。研究结果表明:①稳定剥蚀石英和萤石所需的最小激光能量密度为4～5J/cm~2,低于前人的报道值(10J/cm~2),而稳定剥蚀其他矿物(如滑石、磷灰石、刚玉等)所需的最小能量密度一般在1～2J/cm~2;②不同激光能量密度剥蚀条件下,标准样品中大部分微量元素测试结果与推荐值的相对误差小于20%,相对标准偏差(RSD)小于10%,而天然矿物中含量1μg/g的大部分微量元素测试数据的RSD小于20%;③在一定范围内,激光能量密度越大,数据平均相对误差越小,整体质量更好。 相似文献
5.
6.
激光剥蚀等离子体质谱分析中激光剥蚀参数对信号响应的影响 总被引：5，自引：1，他引：5
探讨了激光剥蚀等离子体质谱固体微区分析中激光剥蚀参数对元素分析信号灵敏度及稳定性的影响。这些参数包括激光功率、脉冲频率、剥蚀孔经、散焦距离、剥蚀方式等。讨论了优化的激光剥蚀等离子体质谱信号采集及数据处理方式。在全质量范围内选用具有代表性的元素作为研究对象,建立了激光剥蚀的一般性特征规律和266nm紫外激光系统的最佳操作条件。在选定的激光剥蚀参数下,大多数被测元素的检出限为22.8~457ng/g,能够满足固体微区分析的要求。 相似文献
7.
利用自然资源部古地磁与古构造重建重点实验室新引进的GeoLas HD型193nm ArF准分子激光剥蚀系统和Agilent 7900型四极杆电感耦合等离子质谱仪,成功建立了LA-ICP-MS锆石微区U-Pb定年及微量元素分析测试方法。以标准锆石91500为外标,在32 μm束斑直径、5.0 J/cm2能量密度和5 Hz剥蚀频率等实验条件下,对Ple?ovice、Temora1和Qinghu锆石标样开展了U-Pb定年实验,所测年龄结果与各标样推荐值在误差范围允许的条件下一致,并且Ple?ovice年龄结果在不同时间段内保持稳定。同时对未知年龄样品11-5开展了不同实验室测年结果对比研究,所测结果与中国地质大学(武汉)地质过程与矿产资源国家重点实验室所测年龄在误差允许范围内一致。以NIST SRM 610为外标,29Si为内标,分析测试了锆石91500和NIST SRM 612标准样品的微量元素含量,实验测试结果与推荐值一致。在此基础上探索总结了不同剥蚀斑束直径对U-Pb年龄结果的影响,认为在同样的能量密度和剥蚀频率条件下,16~44 μm的剥蚀直径可以获取可靠的锆石U-Pb年龄,但32~44 μm相比16~24 μm小斑束直径所测得的年龄更加精准。 相似文献
8.
激光剥蚀电感耦合等离子体质谱（LA-ICP-MS）是目前锆石研究常用方法之一，该法普遍采用环氧树脂靶为载体，对锆石环氧树脂靶表面形貌及平整度影响进行研究，有助于评估其制作工艺以及LA-ICP-MS锆石分析的准确性。本次研究采用原子力显微镜（AFM）对锆石环氧树脂靶表面进行形貌分析，并通过分析和对比193nm激光不同剥蚀模式和不同剥蚀条件下的锆石表面形貌，研究锆石表面形貌及平整度对LA-ICP-MS锆石分析的影响；同时实验采用氩离子抛光技术对锆石环氧树脂靶进行二次抛光，并探讨该技术对锆石环氧树脂靶影响。实验结果表明本次靶中表面总体平整性较好但存在细微的不平，锆石表面存在程度较小（几至几十纳米的不等）的擦痕，锆石颗粒边缘与靶面存在高差和间隙；而通过研究后认为锆石表面细微的不平对于分析的影响小于能量密度、频率、移动速率等其他激光参数的影响，对分析准确性的影响较小。实验分析并对比了锆石和玻璃标准等不同基体的线扫描形貌，发现其剥蚀深度以及剥蚀形貌存在差异，相同剥蚀条件下线扫描剥蚀深度：NIST610 > CGSG系列 > 锆石91500。经氩离子二次抛光后锆石样品表面擦痕不明显，但可能会对锆石造成损伤等影响。本次研究认为锆石环氧树脂靶表面总体平整性较好，锆石表面细微的不平对分析准确性的影响较小，不同基体的线扫描形貌研究则为LA-ICP-MS锆石及其他分析提供了参考，而氩离子抛光技术对LA-ICP-MS分析的影响及应用还有待进一步的研究。 相似文献
9.
锂、铍是当前全球战略性关键金属,采用激光剥蚀电感耦合等离子体质谱(LA-ICP-MS)建立分析方法可以实现微区原位定量分析天然矿物样品中的锂、铍元素含量,为锂铍资源高效利用以及赋存状态的研究提供分析技术支撑。锂辉石和绿柱石等矿物是提取锂、铍元素的主要原料,微区分析常用的电子探针方法对于能量较低的轻元素难以准确定量,而LA-ICP-MS方法亟待改进降低非基体匹配校准带来的基体效应提高分析的准确度和精密度。本文探讨了仪器工作条件(同位素选择及计数模式、载气He气流速、样品气Ar气流速、束斑直径、能量密度大小)和数据处理方法(外部标准物质、内标元素)对定量结果精密度和准确度的影响。实验结果表明：He和Ar气体流速不仅会影响锂、铍信号强度,而且适当降低载气He流速(0.6L/min)可以减小相对误差。增加束斑直径虽可以将数据精密度提高10%以上,但是对于准确度影响不大;对于绿柱石这类硬度高的透明矿物应提高能量密度(相对强度>75%,通量>2.7J/cm2)以保证产生稳定剥蚀信号。测定7Li时选择现有标准物质中含量较高的GSE-1G校准、9Be选择NIST610... 相似文献
10.
激光剥蚀电感耦合等离子体质谱（LA-ICP-MS）副矿物U-Th-Pb定年技术为精确厘定地质演化历史、探讨成岩成矿等重要地质作用过程提供重要的时间参数,是地质年代学快速发展的重要技术支撑.总结了LA-ICP-MS副矿物U-Th-Pb定年技术在元素分馏校正、非基体匹配分析、标准样品研发、普通铅校正、高空间分辨率及高效率分析等方面取得的重要进展.展望未来,需更进一步深入探讨和研究元素分馏及基体效应机理,研发更多种类的高质量副矿物标样,建立更多更准确、更精密、更高空间分辨率及更高效的LA-ICP-MS副矿物U-Th-Pb定年新方法和新技术,以实现从更微观和更精细的角度探讨地质问题,并持续为高效解决地球与行星科学研究领域重大科学问题提供关键支撑. 相似文献
11.
根据1959年和2009年在喜马拉雅山珠穆朗玛峰北坡绒布冰川获得的冰川消融数据, 分析了该冰川消融速率变化特征.结果表明: 1) 在珠峰绒布冰川表碛覆盖区, 表碛厚度随海拔升高而降低. 2) 不同厚度表碛下的冰川消融速率差别较大; 当表碛厚度>8.5 cm时, 消融速率随表碛厚度的增加而减小; 促进冰川消融的表碛厚度阈值大于5 cm. 3) 从冰川消融速率的空间分布看, 绒布冰川大部分区域的消融速率<20 mm·d-1, 最大消融速率出现在海拔5 400~5 450 m处. 4) 绒布冰川消融速率受表碛厚度和气温综合影响, 低海拔处表碛太厚, 高海拔处气温较低, 冰川消融在上述两海拔处均受抑制, 冰川消融速率较小; 在中海拔处, 表碛相对较薄, 气温相对较高, 冰川消融速率最大; 冰川日均消融速率与日均正积温正相关. 5) 喜马拉雅山南坡冰川消融速率大于北坡冰川消融速率. 相似文献
12.
建立了一种利用New Wave UP 213 nm激光和ThermoFisher X Series2四极杆等离子体质谱法直接测定硅酸盐矿物中54种元素的分析方法。该方法以40Ca为内标、玻璃标准参考物质NIST SRM 610为外标,通过调节载气流量、激光频率、激光能量、激光剥蚀斑径降低元素分馏效应,并对NIST SRM 612进行测定,测定结果满足分析要求,54种元素的相对标准偏差大都低于10%,可应用于地质学分析研究。 相似文献
13.
William T. Perkins Nicholas J.G. Pearce John A. Westgate 《Geostandards and Geoanalytical Research》1997,21(2):175-190
This contribution presents a review of the recent developments in laser ablation inductively coupled plasma-mass spectrometry. We describe the important developments which have occurred in the laser systems used, leading to a spatial resolution of around 20 (im, and give an overview of the major instrument developments which have affected the geological applications of laser ablation ICP-MS. We describe the calibration of laser ablation for the analysis of trace elements in two different matrices: volcanic glass shards and sulfide minerals. We show how single glass shards can be analysed using the National Institute of Standards and Technology (NIST) glass certified reference materials for calibration and demonstrate the effect of using single spot analyses compared to rastering of the calibration sample. We show the importance of inter-shard variation and demonstrate that averaged single shard analyses produce data which compare well with bulk analyses. The calibration of the laser system for sulfide mineral analysis is discussed and two different strategies are proposed, one using spiked pressed powder pellets of sulfides and the other metal reference materials. We present conclusions and recommendations for the calibration of laser ablation ICP-MS instruments. 相似文献
14.
Pulok K. Mukherjee Param P. Khanna Naresh K. Saini 《Geostandards and Geoanalytical Research》2014,38(3):363-379
A simple, single sample preparation involving pressed rock powder pellets was utilised to determine the trace and ultra trace abundances of petrogenetically important elements including high field‐strength elements and REEs by laser ablation‐ICP‐MS. One of the elements predetermined by XRF spectrometry served as an internal standard. The influence of sample preparation parameters (grain size, pellet compactness and amount of binding media) on analytical performance was also investigated, including sample homogeneity issues at the laser sampling scale. Line scanning with a high repetition frequency (20 Hz) and large beam diameter (200 μm) ensured ablation from a larger sample surface area, eliminating issues related to sample heterogeneity. A median grain size of about 10 μm for silicate rock powders was found to be sufficiently representative at this scale of laser sampling. Granitic rocks or samples containing resistant minerals such as zircon needed extra grinding to achieve grain sizes down to < 5 μm for better precision for elements that are concentrated in these phases. Using 137Ba as an internal standard, reasonable accuracies within 15–20% for most of the high mass trace elements were achieved; in the case of low mass elements, it may deviate up to 40%. Precision of measurements rarely exceeded 15% RSD. 相似文献
15.
16.
Comparison of measured far-from-equilibrium dissolution rates of natural glasses and silicate minerals at 25 °C and pH 4 reveals the systematic effects of crystallinity and elemental composition on these rates. Rates for both minerals and glasses decrease with increasing Si:O ratio, but glass dissolution rates are faster than corresponding mineral rates. The difference between glass and mineral dissolution rates increases with increasing Si:O ratio; ultra-mafic glasses (Si:O ? 0.28) dissolve at similar rates as correspondingly compositioned minerals, but Si-rich glasses such as rhyolite (Si:O ∼ 0.40) dissolve ?1.6 orders of magnitude faster than corresponding minerals. This behaviour is interpreted to stem from the effect of Si-O polymerisation on silicate dissolution rates. The rate controlling step of dissolution for silicate minerals and glasses for which Si:O > 0.28 is the breaking of Si-O bonds. Owing to rapid quenching, natural glasses will exhibit less polymerisation and less ordering of Si-O bonds than minerals, making them less resistant to dissolution. Dissolution rates summarized in this study are used to determine the Ca release rates of natural rocks at far-from-equilibrium conditions, which in turn are used to estimate their CO2 consumption capacity. Results indicate that Ca release rates for glasses are faster than those of corresponding rocks. This difference is, however, significantly less than the corresponding difference between glass and mineral bulk dissolution rates. This is due to the presence of Ca in relatively reactive minerals. In both cases, Ca release rates increase by ∼two orders of magnitude from high to low Si:O ratios (e.g., from granite to gabbro or from rhyolitic to basaltic glass), illustrating the important role of Si-poor silicates in the long-term global CO2 cycle. 相似文献
17.
Laser Ablation and Solution ICP-MS Determination of Rare Earth Elements in USGS BIR-1G, BHVO-2G and BCR-2G Glass Reference Materials 总被引：2，自引：0，他引：2
Ladislav Strnad Martin Mihaljevic Ondrej Sebek 《Geostandards and Geoanalytical Research》2005,29(3):303-314
Data are reported for rare earth elements (REE) in three geological glass reference materials (BIR-1G, BHVO-2G and BCR-2G) using a UV (266 nm) laser ablation ICP-MS system and the classical (HF-HClO4 ) acid decomposition method, followed by conventional nebulisation ICP-MS. External calibration of laser ablation analyses was performed using NIST SRM reference materials with internal standardisation using 29 Si and 44 Ca. Replicate analyses of reference basaltic glasses yielded an analytical precision of 1-5% (RSD) for all the elements by solution ICP-MS and 1-8% (RSD) by laser ablation ICP-MS. The relative differences between the REE concentrations measured by solution and laser ablation ICP-MS compared with the reference values were generally less than 11 % for most elements. The largest deviations occurred for La determined by solution ICP-MS in BIR-1G. The results of both solution and laser ablation ICP-MS agreed well, generally better than 7%, with the exception of La, Pr and Sm in BIR-1G. The measured REE laser ablation data for BIR-1G, BHVO-2G and BCR-2G agreed with the previously published data on these basaltic reference glasses, within a range of 0-10% for most elements. No significant influences were observed for the predicted spectral interferences on some REE isotopes in the analysis of basaltic glasses. 相似文献
18.
Determination of Lithium, Beryllium and Boron at Trace Levels by Laser Ablation-Inductively Coupled Plasma-Sector Field Mass Spectrometry 总被引：1，自引：2，他引：1
Massimo Tiepolo Alberto Zanetti Riccardo Vannucci 《Geostandards and Geoanalytical Research》2005,29(2):211-224
The analytical capabilities of laser ablation (LA)-ICP-MS in determining Li, Be and B at trace levels in geological samples have been tested on a series of glass reference materials and natural samples. The LA-ICP-MS instrument used consisted of a sector-field ICP-MS coupled with a laser ablation microprobe operating at either 266 or 213 nm wavelength. Reference glasses from NIST (SRM 612, 614 and 616) and MPI-DING (KL2-G, ML3B-G, StHs6/80-G, GOR128-G, GOR132-G, T1-G and ATHO-G) were selected to develop the analytical method and to assess the best instrumental configuration. A series of calcic amphiboles with different Li, Be and B concentrations were also analysed using both LA-ICP-MS and SIMS to test the applicability of the method to natural minerals. Results indicated that with a spot size of 40 μm the agreement between measured and reference values of Li, Be and B is generally better than 10% for NIST SRM 612 and 20% for NIST SRM 614. Average reproducibility at the 2s level was 10% for Li, 20% for Be and 15% for B. Limits of detection were approximately 100 ng g-1 for Be and B and 200 ng g-1 for Li. These results were confirmed by analyses carried out on natural amphiboles and compared well in terms of precision and accuracy with those commonly achieved by SIMS. 相似文献
19.
Joy E. Reid Ingo Horn Henry P. Longerich Lance Forsythe George A. Jenner 《Geostandards and Geoanalytical Research》1999,23(2):149-155
Isotope dilution calibration has been applied to the determination of Zr and Hf in whole rocks by laser ablation (LA)-ICP-MS. Enriched isotopes were added during the preparation of flux-free, synthetic whole rock glasses and homogenised through a combination of grinding and fusion. This method avoids problems, such as solution instability and the chemical resistance of minerals such as zircon, inherent in acid digestion sample preparation. The use of isotope dilution removes the need for external calibration using certified reference material glasses such as NIST SRM 612 for which certified Zr and Hf values are not available. The precision of Zr and Hf determinations were found to be < 1% and 3.5% respectively, limited by Poisson counting statistics which contributed to 50% of the final precision of analysis. Measured values correlate closely with compiled literature values. 相似文献
20.
Mikael D. Axelsson Ilia Rodushkin Douglas C. Baxter Johan Ingri Björn Öhlander 《Geochemical transactions》2002,3(1):40
A procedure was developed for the determination of element distributions in cross-sections of ferromanganese concretions using
laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS). The effects of carrier flow rates, rf forward power,
ablation energy, ablation spot size, repetition rate and number of shots per point on analyte intensity were studied. It is
shown that different carrier gas flow rates are required in order to obtain maximum sensitivities for different groups of
elements, thus complicating the optimisation of ICP parameters. On the contrary, LA parameters have very similar effects on
almost all elements studied, thus providing a common optimum parameter set for the entire mass range. However, for selected
LA parameters, the use of compromise conditions was necessary in order to compensate for relatively slow data acquisition
by ICP-MS and maintain high spatial resolution without sacrificing the multielemental capabilities of the technique. Possible
variations in ablation efficiency were corrected for mathematically using the sum of Fe and Mn intensities. Quantification
by external calibration against matrix-matched standards was successfully used for more than 50 elements. These standards,
in the form of pressed pellets (no binder), were prepared in-house using ferromanganese concentrates from a deep-sea nodule
reference material as well as from shallow-marine concretions varying in size and having different proportions of three major
phases: aluminosilicates, Fe- and Mn-oxyhydroxides. Element concentrations in each standard were determined by means of conventional
solution nebulisation ICP-MS following acid digestion. Examples of selected inter-element correlations in distribution patterns
along the cross-section of a concretion are given. 相似文献