海水中铯-137的γ能谱测量不确定度评估     

魏计房  邓春梅  王荣元  王伟  张馨星  姚海燕  张蒙蒙  丁凯 《海洋学报》2018,40(8):20-28

为科学评价测量结果的可靠性，对海水中137Cs γ能谱分析方法的不确定度进行了评估。根据《化学分析中不确定度的评估指南》，分析不确定度的来源并逐一对各不确定度分量进行了量化，最终计算了合成相对标准不确定度。结果表明，影响海水中137Cs γ能谱测量不确定度的因素分别为样品源137Cs峰区计数、标准源活度、取样体积、化学回收率、本底137Cs峰区计数及标准源137Cs峰区计数，其中样品源137Cs峰区计数的不确定度贡献最为突出。对于137Cs活度浓度为1.28 mBq/L的海水样品，其合成相对标准不确定度为9.78%。  相似文献   

Geophysical Signature of the Shallow Water Flow in the Deepwater Basin of the Northern South China Sea     

Xiaohua Zhang  Yunbao Sun  Shiguo Wu 《中国海洋大学学报(英文版)》2018,17(4):791-798

Shallow water flow (SWF), a disastrous geohazard in the continental margin, has threatened deepwater drilling operations. Under overpressure conditions, continual flow delivering unconsolidated sands upward in the shallow layer below the seafloor may cause large and long-lasting uncontrolled flows; these flows may lead to control problems and cause well damage and foundation failure. Eruptions from over-pressured sands may result in seafloor craters, mounds, and cracks. Detailed studies of 2D/3D seismic data from a slope basin of the South China Sea (SCS) indicated the potential presence of SWF. It is commonly characterized by lower elastic impedance, a higher Vp/Vs ratio, and a higher Poisson’s ratio than that for the surrounding sediments. Analysis of geological data indicated the SWF zone originated from a deepwater channel system with gas bearing over-pressured fluid flow and a high sedimentation rate. We proposed a fluid flow model for SWF that clearly identifies its stress and pressure changes. The rupture of previous SWF zones caused the fluid flow that occurred in the Baiyun Sag of the northern SCS.  相似文献   

海岸破波带内悬沙空间分布试验研究和解析表达式     

张洋  邹志利  孙大鹏  薛武山 《海洋工程》2018,36(1):28-46

关于海岸破波带内悬沙浓度水平和垂向分布的研究对于计算海岸输沙率和地形演变具有重要意义。本研究进行了规则波、波群和不规则波三种波浪情况破波带内悬沙浓度的水平和垂向分布的试验测量。试验在大尺度波浪水槽进行,接近实际海岸波况尺度。给出了破波带内多断面悬沙垂向分布的细致测量结果,并以此为基础给出了预报实际海岸破波带内悬沙浓度水平和垂向分布解析表达式,讨论了形成这些分布的物理原因和不同波况、不同破波带区域对分布的影响。  相似文献   

光照强度和光色对番红砗磲(Tridacna crocea)氨氮、活性磷酸盐及氧代谢的影响     

刘春胜  刘小霞  汪浩  王爱民  顾志峰 《海洋与湖沼》2018,49(2):313-318

采用室内实验生态学方法,以水体中氨氮、活性磷酸盐和溶氧变化为指标研究了光照强度和光色对番红砗磲代谢的影响。结果表明:(1)在0—10000lx光照时,番红砗磲排氨量逐渐减少,在光照12000lx时转为吸收海水中氨氮,并在16000lx时达到最高[1.89μg/(ind·h)];在2000lx光照条件下,番红砗磲可吸收海水中活性磷酸盐并释放氧气。其活性磷酸盐吸收量随光照强度增强而增加,在16000lx时达到最高峰。在实验光照范围内,番红砗磲产氧率随光照强度的增强逐渐增加。上述结果显示番红砗磲最佳光照强度约为16000lx。(2)当番红砗磲自黑暗转移至各光照组后,其氨氮、活性磷酸盐吸收率均随时间逐渐降低,而产氧率则逐渐升高。(3)光色显著影响番红砗磲合成代谢,蓝光最佳,红光次之,白光最差。  相似文献   

典型深街谷内树木空间配置对行人呼吸高度处气流的影响     

林定  申小云  朱勇兵  陈崇成 《地球信息科学学报》2018,20(9):1235-1243

为揭示树木的不同空间配植方案对行人呼吸高度气流的影响,本文将树木视为均匀多孔介质,通过附加源项法从空气动力学角度用CFD模拟了H/W=2的典型深街谷几何内4种树木配植情景,实验表明,不同空间配置下树木对街谷内行人呼吸高度处局地气流的影响强弱在空间分布模式上差异悬殊：① 均匀种植的树木对街谷内行人呼吸高度的气流起到阻碍作用,不均匀种植则有效提升街谷的整体流速。4种空间配植方案下树木对气流的影响程度不同,阻碍作用从大到小的顺序为均匀间距8 m（Spa8m）>均匀间距6 m（Spa6m）>均匀间距20 m（Spa20m）>不均匀配植（Non-uniform）;对应的平均气流增强指标顺序为$\bar{D}_{spa8}$（-19.31%）<$\bar{D}_{spa6}$（-16.14%）<$\bar{D}_{spa20}$（-10.73%）<$\bar{D}_{non-uniform}$（1.25%）。② 对比不均匀和均匀的种植方案,不均匀植树的街谷内部行人呼吸高度的气流流速比其对照案例（均匀植树Spa8m方案）整体增强了106.49%。街谷中部不种树,在街谷两端配置树木并预留足够的自由空间的不均匀植树方案,能够让角涡渗入街谷中部,促使街谷内部的垂直漩涡和两端的水平角涡运动,增强湍流和垂直交换,有效减少了街道两端“风口效应”和街道中部“风影效应”的区域,改善了整个街谷行人呼吸平面的风环境。④ 合理空间配置的树木能够改善街谷内部的行人风环境。街谷内行人呼吸高度处的气流对局地条件很敏感,树木的局部配置（空间簇集、密度）将引起强烈的空间变化。在既有城市建筑布局条件下,如何通过谨慎的景观设计,利用树木等城市绿化措施有效地改善城市的行人风环境,缓解污染扩散、疾病传播等问题,本文的方法可提供一定的参考。  相似文献   

Regional Characteristics and Causes of Haze Events in Northeast China     

Weiwei Chen  Shichun Zhang  Quansong Tong  Xuelei Zhang  Hongmei Zhao  Siqi Ma  Aijun Xiu  Yuexin He 《中国地理科学(英文版)》2018,28(5):836-850

Northeast China experiences severe atmospheric pollution, with an increasing occurrence of heavy haze episodes. However, the underlying forces driving haze formation during different seasons are poorly understood. In this study, we explored the spatio-temporal characteristics and causes of haze events in Northeast China by combining a range of data sources(i.e., ground monitoring, satellite-based products, and meteorological products). It was found that the ‘Shenyang-Changchun-Harbin(SCH)'city belt was the most polluted area in the region on an annual scale. The spatial distribution of air quality index(AQI) values had a clear seasonality, with the worst pollution occurring in winter, an approximately oval-shaped polluted area around western Jilin Province in spring, and the best air quality occurring in summer and most of the autumn. The three periods that typically experienced intense haze events were Period I from mid-October to mid-November(i.e., late autumn and early winter), Period II from late-December to February(i.e., the coldest time in winter), and Period III from April to mid-May(i.e., spring). During Period I, strong PM_(2.5) emissions from seasonal crop residue burning and coal burning for winter heating were the dominant reasons for the occurrence of extreme haze events(AQI 300). Period II had frequent heavy haze events(200 AQI 300) in the coldest months of January and February, which were due to high PM_(2.5) emissions from coal burning and vehicle fuel consumption, a lower atmospheric boundary layer, and stagnant atmospheric conditions. Haze events in Period III, with high PM_(10) concentrations, were primarily caused by the regional transportation of windblown dust from degraded grassland in central Inner Mongolia and bare soil in western Jilin Province. Local agricultural tilling could also release PM_(10) and enhance the levels of windblown dust from tilled soil. Better control of coal burning, fuel consumption, and crop residue burning in winter and autumn is urgently needed to address the haze problem in Northeast China.  相似文献   

Responses of soil moisture to vegetation restoration type and slope length on the loess hillslope     

Xue-mei Mei  Lan Ma  Qing-ke Zhu  Shu Wang  Dong Zhang  Yu Wang 《山地科学学报》2018,15(3):548-562

Soil moisture, a critical variable in the hydrologic cycle, is highly influenced by vegetation restoration type. However, the relationship between spatial variation of soil moisture, vegetation restoration type and slope length is controversial. Therefore, soil moisture across soil layers (0-400 cm depth) was measured before and after the rainy season in severe drought (2015) and normal hydrological year (2016) in three vegetation restoration areas (artificial forestland, natural forestland and grassland), on the hillslopes of the Caijiachuan Catchment in the Loess area, China. The results showed that artificial forestland had the lowest soil moisture and most severe water deficit in 100-200 cm soil layers. Water depletion was higher in artificial and natural forestlands than in natural grassland. Moreover, soil moisture in the shallow soil layers (0-100 cm) under the three vegetation restoration types did not significantly vary with slope length, but a significant increase with slope length was observed in deep soil layers (below 100 cm). In 2015, a severe drought hydrological year, higher water depletion was observed at lower slope positions under three vegetation restoration types due to higher transpiration and evapotranspiration and unlikely recharge from upslope runoff. However, in 2016, a normal hydrological year, there was lower water depletion, even infiltration recharge at lower slope positions, indicating receiving a large amount of water from upslope. Vegetation restoration type, precipitation, slope length and soil depth during a rainy season, in descending order of influence, had significant effects on soil moisture. Generally, natural grassland is more beneficial for vegetation restoration than natural and artificial forestlands, and the results can provide useful information for understanding hydrological processes and improving vegetation restoration practices on the Loess Plateau  相似文献   

Bearing capacity of offshore umbrella suction anchor foundation in silty soil under varying loading modes     

Qi Yang  Guanglai Pan  Quandi Wang 《Marine Georesources & Geotechnology》2018,36(7):781-794

Considering the current disadvantages of present offshore wind turbine foundations, a novel anchor foundation with skirt and branches is proposed, called offshore umbrella suction anchor foundation (USAF). A series of experiments and numerical simulations were performed to explore the bearing capacity of the USAF under various kinds of loading modes. The bearing characteristics and the anchor–soil interactions are described in detail for horizontal static loading, horizontal cyclic loading, and an antidrawing (pullout) test in silty soil. In the static loading test, the load–deflection of the anchor under step loading was analyzed and the normalized curve of the load–deflection was obtained to determine the ultimate horizontal bearing capacity of the anchor under normal working conditions. Under horizontal cyclic loading, the relationship between the plastic cumulative deformation and cyclic number was determined. In addition, the responses of USAF were investigated for a low wave frequency and storm surges. In the drawing test, it was found that a “segmentation phenomenon” occurred during the test. Moreover, a method to identify the maximum antidrawing load of USAF was provided based on dynamic mechanics. The numerical results show that the use of anchor branches and skirt can enhance the bearing performance of USAF to a certain degree. However, the anchor branch has a slight positive influence on the bearing performance improvement. The USAF is not only similar to a stiff short pile, but a rotation occurs. The failure envelope under composite loading (V-M) was obtained and the changes associated with changes in the aspect ratio of the internal compartment were clarified.  相似文献   

环塔里木盆地绿洲城市发展与水环境质量协调度     

孜比布拉·司马义  杨胜天  杨晓东  王蕾  肖合来提·巴义 《中国沙漠》2020,40(1):88-96

解决好新疆环塔里木盆地绿洲城市发展与水环境质量之间的关系，对"一带一路"倡议顺利实施及新疆社会稳定具有十分重要的作用。基于2004-2017年环塔里木盆地绿洲城市发展与水环境变化状况，构建城市发展与水环境质量的综合评价模型及二者的协调度模型，以探讨环塔里木盆地绿洲城市发展、水环境质量变化及二者的协调关系。结果表明：2004-2017年，（1）环塔里木盆地绿洲城市发展综合指数呈现出逐年稳定上升的趋势，经济发展和城镇空间规模扩大是环塔里木盆地绿洲城市发展的主要形式；（2）环塔里木盆地绿洲城市的水环境质量综合指数呈现出逐年降低的趋势，水环境质量形势严峻；（3）环塔里木盆地绿洲城市发展-水环境质量系统的协调度呈现倒U型的稳定发展趋势，但总体上两者的协调度较低，城市发展和水环境质量之间的矛盾日益突出。  相似文献   

A multiscale work-analysis approach for geotechnical structures     

Hao Xiong  Zhen-Yu Yin  François Nicot 《国际地质力学数值与分析法杂志》2019,43(6):1230-1250

This paper presents a second-order work analysis in application to geotechnical problems by using a novel effective multiscale approach. To abandon complicated equations involved in conventional phenomenological models, this multiscale approach employs a micromechanically-based formulation, in which only four parameters are involved. The multiscale approach makes it possible a coupling of the finite element method (FEM) and the micromechanically-based model. The FEM is used to solve the boundary value problem (BVP) while the micromechanically-based model is utilized at the Gauss point of the FEM. Then, the multiscale approach is used to simulate a three-dimensional triaxial test and a plain-strain footing. On the basis of the simulations, material instabilities are analyzed at both mesoscale and global scale. The second-order work criterion is then used to analyze the numerical results. It opens a road to interpret and understand the micromechanisms hiding behind the occurrence of failure in geotechnical issues.  相似文献