We designed a new seismic source model for Italy to be used as an input for country-wide probabilistic seismic hazard assessment (PSHA) in the frame of the compilation of a new national reference map.
We started off by reviewing existing models available for Italy and for other European countries, then discussed the main open issues in the current practice of seismogenic zoning.
The new model, termed ZS9, is largely based on data collected in the past 10 years, including historical earthquakes and instrumental seismicity, active faults and their seismogenic potential, and seismotectonic evidence from recent earthquakes. This information allowed us to propose new interpretations for poorly understood areas where the new data are in conflict with assumptions made in designing the previous and widely used model ZS4.
ZS9 is made out of 36 zones where earthquakes with Mw > = 5 are expected. It also assumes that earthquakes with Mw up to 5 may occur anywhere outside the seismogenic zones, although the associated probability is rather low. Special care was taken to ensure that each zone sampled a large enough number of earthquakes so that we could compute reliable earthquake production rates.
Although it was drawn following criteria that are standard practice in PSHA, ZS9 is also innovative in that every zone is characterised also by its mean seismogenic depth (the depth of the crustal volume that will presumably release future earthquakes) and predominant focal mechanism (their most likely rupture mechanism). These properties were determined using instrumental data, and only in a limited number of cases we resorted to geologic constraints and expert judgment to cope with lack of data or conflicting indications. These attributes allow ZS9 to be used with more accurate regionalized depth-dependent attenuation relations, and are ultimately expected to increase significantly the reliability of seismic hazard estimates. 相似文献
A crucial point in any methodology for avalanche hazard assessment is the evaluation of avalanche distance exceeded probability, i.e., the annual probability that any assigned location along a given path is reached or exceeded by an avalanche. Typically this problem is faced by estimating the snow volume in the starting zone that is likely to accumulate an average every T years by statistical analysis of snowfall record, and then using this volume as input to an appropriately calibrated avalanche dynamics model to determine the runout distancesfor this design event. This methodology identifies the areas that canbe affected by an avalanche for the considered value of the return period (i.e. the average interval of time for a certain event to repeat itself), ¯T. However, it does not allow us to evaluate the actual avalanche encounter probability for any given point in the runout zone. In the present work this probability is computed by numerical integration of the expression P(x) = ∫0∞ P*(V)f(V) dV, where f is the probabilitydensity function (PDF) of the avalanche release volume V, and P* is the probability of the point x being reached or passed by an avalanche if the release volume is V; this latter probability is calculated by avalanche dynamics simulations. The procedure is implemented using a one-dimensional hydraulic-continuum avalanche dynamic model, calibrated on data from different Italian Alpine ranges, and is applied to a real world hazard mapping problem. 相似文献
LIDAR (Light Detection and Ranging) is one of the most recent technologies in surveying and mapping. LIDAR is based on the combination of three different data collection tools: a laser scanner mounted on an aircraft, a Global Positioning System (GPS) used in phase differential kinematic modality to provide the sensor position and an Inertial Navigation System (INS) to provide the orientation. The laser sends towards the ground an infrared signal, which is reflected back to the sensor. The time employed by the signal, given the aircraft position and attitude, allows computation of the earth point elevation. In standard conditions, taking into account the flight (speed 200–250 km/hour, altitude 500–2,000 m) and sensor characteristics (scan angle ± 10–20 degrees, emission rate 2,000–50,000 pulses per second), earth elevations are collected within a density of one point every 0.5–3 m. The technology allows us therefore to obtain very accurate (5–20 cm) and high resolution Digital Surface Models (DSM). For many applications, the Digital Terrain Model (DTM) is needed: we have to automatically detect and discard from the previous DSM all the features (buildings, trees, etc.) present on the terrain. This paper describes a procedure that has been implemented within GRASS to construct DTMs from LIDAR source data. 相似文献
A multi‐method approach (palaeothermal and thermochronological analyses; thermal modelling) is applied to reconstruct the exhumation history of the Altotiberina Fault (ATF), a representative example of crustal‐scale active low‐angle normal faulting in the Northern Apennines (Italy). Thermal maturity and thermochronological data yield similar burial histories but different exhumation patterns for the sedimentary successions in the hangingwall and the footwall of the ATF. Since 3.8 Ma, the ATF footwall has exhumed at rates of 0.90 mm a?1. Exhumation led to bending and deactivation of the ATF uppermost portion as a result of tectonic unloading and isostatic adjustment, followed by migration of extension and the development of a set of domino‐like, east‐dipping normal faults, rooting on the buried portion of the ATF. ATF activity and isostatic rebound exhumed Triassic rock units from depths of about 4 km. We suggest that isostatic instability is accommodated at shallow crustal levels, in a similar way to what is observed on larger structures at mid‐low crustal levels. 相似文献
Computational Geosciences - Anthropogenic land subsidence can be evaluated and predicted by numerical models, which are often built over deterministic analyses. However, uncertainties and... 相似文献
Compositional control on the annealing kinetics of fission-tracks (FT) in apatite requires routine measurement of sample grain composition. However, for practical reasons the bulk composition of analysed grains is not routinely measured and instead grain chlorine content or etch-pit dimensions are used to characterise a samples annealing behaviour. A more desirable approach is to measure crystallographic parameters (i.e. unit cell dimension) of a grain as these represent the summed effect of all substitutions and crystal defects. We show how Raman microspectrometry can be used as a routine non-destructive tool to obtain rapid measurement of the crystallographic structure of apatite grains etched for FT analysis. Variations of unit cell parameter a are found to correspond to a systematic variation of Raman shift in the range of 452–440 cm− 1 for measurements made on c-parallel sections of apatite where the direction of the polarized incident beam is parallel to the c axis. 相似文献
The planetary boundary-layer (PBL) parameterization is a key issue for the definition of initial wind flow fields in diagnostic
models. However, PBL theories usually treat separately stable, neutral, and convective stability conditions, so that their
implementation in diagnostic wind models is not straightforward. In the present paper, an attempt is made to adopt a comprehensive
PBL parameterisation, covering stable/neutral and unstable atmospheric conditions, which appears suitable to diagnostic models.
This parameterisation is implemented into our diagnostic mass-consistent code. A validation of the consistency between the
implemented PBL parameterisations has been checked through an analysis of the sensitivity of the vertical wind profiles to
atmospheric stability. 相似文献