排序方式： 共有160条查询结果，搜索用时 218 毫秒
31.
David J. Milan 《地球表面变化过程与地形》2013,38(14):1623-1641
This paper provides comprehensive evidence that sediment routing around pools is a key mechanism for pool‐riffle maintenance in sinuous upland gravel‐bed streams. The findings suggest that pools do not require a reversal in energy for them to scour out any accumulated sediments, if little or no sediments are fed into them. A combination of clast tracing using passive integrated transponder (PIT) tagging and bedload traps (positioned along the thalweg on the upstream riffle, pool entrance, pool exit and downstream riffle) are used to provide information on clast pathways and sediment sorting through a single pool‐riffle unit. Computational fluid dynamics (CFD) is also used to explore hydraulic variability and flow pathways. Clast tracing results provide a strong indication that clasts are not fed through pools, rather they are transported across point bar surfaces, or around bar edges (depending upon previous clast position, clast size, and event magnitude). Spatial variations in bedload transport were found throughout the pool‐riffle unit. The pool entrance bedload trap was often found to be empty, when the others had filled, further supporting the notion that little or no sediment was fed into the pool. The pool exit slope trap would occasionally fill with sediment, thought to be sourced from the eroding outer bank. CFD results demonstrate higher pool shear stresses (τ ≈ 140 N m–2) in a localized zone adjacent to an eroding outer bank, compared to the upstream and downstream riffles (τ ≈ 60 N m–2) at flows of 6 · 2 m3 s–1 (≈ 60% of the bankfull discharge) and above. There was marginal evidence for near‐bed velocity reversal. Near‐bed streamlines, produced from velocity vectors indicate that flow paths are diverted over the bar top rather than being fed through the thalweg. Some streamlines appear to brush the outer edge of the pool for the 4 · 9 m3 s–1 to 7 · 8 m3 s–1 (between 50 and 80% of the bankfull discharge) simulations, however complete avoidance was found for discharges greater than this. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
32.
33.
运用流体力学软件FloEFD对沽源单个建筑物周围的风场进行数值模拟。通过不断改变模型中计算参数的设置进行一系列模拟试验,对比模拟试验结果,并与观测资料进行比较,分析不同计算参数对模拟结果的影响,并获得适用于该模型的最佳参数。主要研究的计算参数包括计算域高度,初始网格等级,局部初始网格等级和不同平均风速剖面形式。结果表明:计算域高度从3倍建筑物高度开始,空腔区的长度、漩涡中心位置以及再发展区的边界位置基本保持稳定。随着初始网格等级的增加,空腔区的长度、再发展区的边界位置及计算时间逐渐增大。局部初始网格等级对模拟结果影响不显著。以两种不同平均风速剖面形式进行模拟,迎风漩涡长度不同,背风面影响不大。与观测资料比较显示,最优参数组合为:计算域高度为3倍建筑物高度,初始网格等级为4、局部初始网格等级为4、平均风速剖面形式为指数律。 相似文献
34.
The computer simulation is an important method for hydrokinetic hammer design. Various kinds of simulation measures with their technical characters and applications being taken during the computer aided design are enumerated. Computer simulation supports plenty of valuable references to the designer. Each type of simulation process is used to explore the exact aspect of the performance of hydrokinetic hammer and each type of simulation method has its own excellences and deficiencies. Thus the integrative simulation methods based on modern computational technology are brought forward to obtain the perfect capability of the whole product. Along with the development of computer hardware and software, various kinds of platforms have been provided to different simulation methods that can be carried out with distinct working flows. The jet flow element is the core part of the hydrokinetic hammer. We can build the ideal simulation model of it by means of CFD (computational fluid dynamics) technology. On the other hand, to set up the digital model of piston and hammer, the best way is to build the virtual prototype using automatic dynamic analysis of mechanical system. As a result of the argumentation, we think the technique of Virtual Prototype and CFD are the prime way to process the combined computer simulation for hydrokinetic hammer. 相似文献
35.
An extensive experimental investigation on four SWATH hull forms has been conducted in calm water and in regular waves at University of Naples Federico II. Calm water tests have been analyzed in the range of Froude number FrT from 0.1 to 0.6. For all four SWATH configurations at the speed, corresponding to FrT 0.32, the behaviour in regular waves has been tested. The results of heave, pitch and vertical accelerations are presented in nondimensional form as RAO. For the “most promising” SWATH #4 configuration, a set of stabilizing fins have been designed and an active stabilization system has been developed. The developed SWATH#5 has been tested in calm water on three displacements in the range of FrT from 0.1 to 0.65. The dynamic wetted surface has been identified and the residual resistance coefficient CR as well as RT/Δ are reported. Seakeeping tests have been performed in regular head sea and in head and following irregular sea at FrT = 0.50. The conditions for the occurrence of dynamic longitudinal instabilities have been identified. The results allows to comment the effect of slenderness of struts and SWATH’s immersed bodies on resistance and seakeeping and concerns the applicability of SWATH concept to small craft. 相似文献
36.
Conductor casing jetting technique has been increasingly applied in deepwater drilling. The insight into the jetting excavation mechanisms is critical in guiding a successful conductor casing jetting operation. The real- time continuous jet excavation process is simulated with the volume of fluid (VOF) multiphase method of CFD (Computational Fluid Dynamics) ANSYS Fluent calculation software in the current study. The cohesive soil is modelled by using a kind of viscous fluid with Herschel-Bulkley model. In addition, a laboratory half round nozzle jet excavation test is designed for verification by comparison of the observed jet excavation profile with the numerical results. The sensitivity parameters affecting the conductor jetting excavation mechanism in cohesive soil are thus investigated. It is found that the application of Herschel-Bulkley (HB) model for cohesive soil and the VOF method of Fluent can provide a good simulation of jet excavation process. The maximum excavation depth can be determined by the undrained ultimate bearing capacity of the circular foundation with a bearing capacity factor of 6.7. The nozzle position, jet velocity and soil strength have significantly influence on the depth and width of the jet excavation profile in conductor oblique jet. 相似文献
37.
Wave Energy Converters (WECs) have excellent potential as a source of renewable energy that is yet to be commercially realised. Recent attention has focused on the installation of Oscillating Water Column (OWC) devices as a part of harbor walls to provide advantages of cost–sharing structures and proximity of power generation facilities to existing infrastructure. In this paper, an incompressible three–dimensional CFD model is constructed to simulate a fixed Multi–Chamber OWC (MC–OWC) device. The CFD model is validated; the simulation results are found to be in good agreement with experimental results obtained from a scale physical model tested in a wave tank. The validated CFD model is then used for a benchmark study of 96 numerical tests. These investigate the effects of the PTO damping caused by the power take–off (PTO) system on device performance. The performance is assessed for a range of regular wave heights and periods. The results demonstrate that a PTO system with an intermediate damping can be used for all chambers in the MC–OWC device for most wave period ranges, except for the long wave periods. These require a higher PTO damping. An increased incident wave height reduces the device capture width ratio, but there is a noticeable improvement for long wave periods. 相似文献
38.
39.
When a vessel is damaged, seawater floods into the damaged compartments and subsequently influences the motion of the vessel. Furthermore, the vessel’s behaviour affects the floodwater motion. In this paper, a Navier-Stokes (NS) solver with a free surface capturing technique, i.e., the volume of fluid (VOF) method, was developed to numerically simulate water flooding into a damaged vessel. To verify the developed solver, a 2-D and a 3-D dam break problems were tested. The numerical results coincide well with the experimental results and with the published numerical results. Additionally, it was used to solve the problems of linear and non-linear liquid sloshing in a hexahedral tank. The numerical results are satisfactory in comparison with the experimental results and analytical solutions. Finally, the phenomenon of water flooding into a damaged compartment of a Ro-Ro ferry was simulated numerically. The computed results are in good agreement with the experimental data. 相似文献
40.
Numerical modelling of deep sea air-lift 总被引：2，自引：0，他引：2
Deep sea air-lifting of solid particles from depth of 1600 m is simulated with a mathematical model of the three-phase flow in an upward pipe. The computations are carried out for an axisymmetric domain in a transient way. Phase distributions, pressure and velocity profiles together with flow rates for all phases are presented and analysed. The influence of the pipe diameter on the air-lift efficiency was studied for air-lift pipes of different lengths and found to be significant. The lifting efficiency increases with the increase of the pipe diameter due to the reduction of the wall friction influence on the flow. In addition, the efficiency also increases with the increase of the solid particles volume fraction at the inlet. The presented numerical model can be utilized during various stages of the design of the air-lift pumps to help answer fundamental questions on the process, and during their operation to select optimal process parameters and to address possible problems. 相似文献