南京周家山下蜀黄土石英颗粒特征及其物源意义   总被引：1，自引：1，他引：0  

徐洪阳  郑祥民  周立旻  任少芳  王小玉  玄晓娜 《沉积学报》2016,34(6):1176-1186

下蜀黄土的成因和物源一直是学术界研究的热点。对南京周家山下蜀黄土的石英粒度和石英表面微结构进行分析,结果显示:粉砂粒级石英颗粒（5~50 μm）占绝对优势;<20 μm组分平均含量为42.76%,<30 μm组分平均含量为62.98%;粒度分布曲线和累积曲线总体具有颗粒偏细,呈正偏态,分选较差,峰形尖锐,双峰曲线不对称的特征;粒级-标准偏差曲线呈“双峰”分布,两个明显的标准偏差峰值分别出现在7.962 1 μm和39.905 2 μm。石英颗粒表面形态主要以次棱角状为主;表面机械结构具有丰富的蝶形坑、曲脊、贝壳状断口,部分表面出现平行节理面、V形坑;不同粒级组分表面形态和机械结构特征存在差异。分析表明,南京周家山下蜀黄土属典型风成成因堆积物,是多源区物质高度混合搬运堆积的结果。  相似文献   

大直径加重管绳索取心技术在页岩气勘探中的应用研究          下载免费PDF全文

朱恒银  王强  张正  蔡正水 《探矿工程》2016,43(10):160-164

根据页岩气、煤层气勘探对钻探技术的特殊要求,进行了大直径绳索取心技术的探索研究。文中重点介绍了加重管组合式绳索取心钻具的结构、作用原理及特点,以及施工试验效果。通过施工实践的启示,对大直径绳索取心技术的发展提出了几点认识。  相似文献   

内蒙古达来诺尔湖湖泊沉积物中敏感粒度组分沉积环境及地层分析   总被引：1，自引：0，他引：1       下载免费PDF全文

于瑞雪  李畅游  李文宝  甄志磊  赵胜男  张帅 《沉积与特提斯地质》2016,36(3):77-82

对达来诺尔湖北岸岸边(DL-0)、湖中心(DL-1)和湖南岸(DL-2)3个点的岩心沉积物进行了详细的岩性分析、粒度分析和粒度参数垂向分布序列分析。对沉积环境变化较为敏感的粒度组分的分析发现DL-0与DL-1和DL-2井岩心沉积物敏感粒度组分的峰值有较大差别,其粒度分布范围相差较大,表明湖北岸岸边、湖中心和湖南岸的沉积物来源和沉积环境的时空差异。敏感粒度组分含量随深度变化的初步分析表明,湖北岸岸边(DL-0)和湖中心(DL-1)两个点的沉积环境较为稳定;而位于湖南岸(DL-2)点的沉积环境变化比较大,包含了5个明显的沉积波动旋回,并对达来诺尔湖由北至南进行了沉积地层分析。在达来诺尔湖水下1.5m内主要是粒径0~200μm的颗粒,岩性为粘土、粉砂和砂,以粘土和粉砂为主,随着深度的增加,黏土含量增大,粉砂和砂含量减小。  相似文献   

末次冰盛期后黄河三角洲沉积物的磁性特征及其沉积环境   总被引：1，自引：0，他引：1  

彭俊  李平  陈洪全 《海洋学报(英文版)》2016,35(5):113-123

On the basis of measuring the magnetic parameters of sediment in Core YDZ1, combined with a grain size analysis and Carbon-14 dating, the magnetic properties of sediment and sedimentary environment in the Huanghe(Yellow River) Delta area after the last glacial maximum have been studied. The results show that the ferrimagnetic minerals of a pseudo single domain and multi domain particles dominate the magnetic properties of sediment in Core YDZ1. The imperfect anti ferrimagnetic minerals have more contribution on sediment in a depth of 24.0–22.1 m, and more stable-single domain and pseudo single domain particles exist. The susceptibility of anhysteretic remanent magnetization and the ratio of the susceptibility of anhysteretic remanent magnetization to saturation isothermal remanent magnetization show a decrease trend below depth of 24 m, a marked increase trend in a depth of 24.0–13.5 m, and a rapid decrease at depth of 13.5 m, then a fluctuation trend upward. The above two magnetic parameters and the ratio of the susceptibility of anhysteretic remanent magnetization to the mass susceptibility can be regarded as the proxy indicators for the content of clay(4 μm)and the fine-grained size(32 μm). The sedimentary environment after the last glacial maximum in the Huanghe Delta area has experienced the fluvial facies, the tidal flat facies, the neritic facies, the pro delta facies, the delta front facies and the floodplain facies. Thickness of the Holocene transgression layer is 10.5 m and the depth of substrate is about 24 m according to the YDZ1 core. The sedimentary dynamic has a variation trend with strongweak-strong, which has been proved by the Flemming triangular schema.  相似文献   

东山乌礁湾海滩表层沉积物粒度时空变化分析     

周在明  杨燕明  陈本清 《海洋科学》2016,40(10):82-90

为了进一步了解海岛岬湾海岸表层沉积物粒度的时空分布特征和形成机制,作者以福建东山岛乌礁湾为典型研究区,通过秋、春、夏3个不同季节海滩表层沉积物的采集和点位测量,综合应用激光法和筛析法进行粒度测定。结果表明,东山乌礁湾海滩表层沉积物以0.16～0.50 mm之间的中、细砂为主,并含有少量的粗砂和细砾,这与区域砂质沉积背景有关;湾内从南到北剖面沉积物粒径由粗砂到细砂逐渐变细,主要受剖面地形、局地物源、季节性风浪作用和近岸往复水动力的影响。时间变化上,各取样站位表现出沉积物粒径粗、细不同程度的多种变化趋势,以秋季为参考,整体上表现为由南到北粒级的变小、增大和稳定,这与东北、南南西季风影响下的浪、潮作用以及沿岸流系格局变化下的水动力环境有关。  相似文献   

青藏高原东北部降尘通量及粒度特征分析          下载免费PDF全文

鄂崇毅  席永帅  孙永娟  赵亚娟  杨龙  吕顺昌 《盐湖研究》2016,24(2):62-67, 74

青藏高原东北缘是柴达木沙尘暴东移的必经之道和沉降区,对青藏高原东北部降尘时空分异特征进行分析,有助于认识青藏高原区域粉尘输送的现代过程和机制。2013年12月至2015年5月分别在青海湖小泊湖(XBH)、西宁多巴(DB)、西宁青海师大科技楼顶(KJLD)设置降尘缸,进行湿法收集。对其降尘通量和粒度特征进行了时空分异特征分析,结果显示,1)西宁地区2014年降尘通量为442~542 g/m~2·a,青海湖XBH采集点指示的2014年降尘通量为415 g/m~2·a,降尘通量年际变化较大,各站点降尘通量季节变化趋势一致,降尘主要集中在冬春季,夏季降尘通量最低;2)各站点降尘粒度组成特征非常相似,以粉砂为主(4~63μm),西宁地区尘暴与非尘暴降尘粒度频率曲线呈近似正态分布,尘暴期间降尘粒径较非尘暴时段大;3)XBH、DB和KJLD 3点所有样品平均粒径分别为37μm、34μm和31μm,中值粒径分别为31μm、27μm和26μm;对比低海拔兰州尘暴粒径特征,发现降尘粒径存在一定的海拔依赖性,即粒度随海拔增高逐渐变粗。  相似文献   

The effect of specimen diameter size on uniaxial compressive strength,P-wave velocity and the correlation between them     

Amin Jamshidi  Mashalah Khamehchiyan  Reza Zarei Sahamieh 《Geomechanics and Geoengineering》2016,11(1):13-19

Estimation of uniaxial compressive strength (UCS) by P-wave velocity (V_P) is of great interest to geotechnical engineers in various design projects. The specimen diameter size is one of the main factors that influence rock parameters such as UCS and V_P. In this study, the diameter size of specimens that effect UCS and V_P is investigated. Moreover, the correlation between UCS and V_P are examined via empirical analysis. For this purpose, 15 travertine samples were collected and core specimens with a diameters size of 38, 44, 54, 64 and 74 mm were prepared. Then, uniaxial compressive strength and P-wave velocity tests were conducted according to the procedure suggested by ISRM (1981). It is concluded that the diameter size of the specimen has a significant effect on UCS and V_P. Moreover, it was found that the best correlation between relevant parameters obtained for the specimen diameter of 38 mm.  相似文献   

Effects of Column Diameter on Setting Behavior of Dredged Slurry in Sedimentation Experiments     

Yu-Feng Gao  Yuan Zhou  Da-yong Li 《Marine Georesources & Geotechnology》2016,34(5):431-439

This article investigates the influence of dimensions of a settling column on the settling mode and the settling rate. End conditions of the settling stage in the hindered settling were also analyzed. It was found that the settling mode in a column with a smaller diameter tends to be consolidation settling. The effect of a settling column wall decreases with increasing column diameter, and it can be ignored provided the column diameter is larger than 14.5 centimeters. For the difference in initial water content, the settling behavior of the slurry develops a different sensitivity to the diameter effect. The influence of column diameter reduces as the initial water content of the slurry becomes higher. It is suggested that the internal diameter of the column used in a sedimentation experiment should be 14.5 centimeters.  相似文献   

Main technical innovations of Songke Well No.2 Drilling Project     

《China Geology》2018,1(2):187-201

Songke Well No.2, one of the main part of the scientific drilling project in Songliao Basin, which was drilled 7018 m and acquired the part of cores continuously from the Low Cretaceous to the Carboniferous and the Permian from the 2843 m deep, can be considered as the deepest continental drilling project in Asia. Aiming at the features of longer well sections, larger diameters and multiple spud-ins for coring of Songke Well No.2, this project broke through the “coring in small diameter and reaming in large diameter” spud-in drilling-completion procedures which are always used in large-diameter-well coring for continental scientific drilling projects in domestic and overseas and the drilling method of short-single-cylinder roundtrip footage. At the same time, “coring in the same diameter and completing drilling at one single diameter” was achieved at all φ311 mm and φ216 mm coring sections of more than one thousand meters long, high-efficient operation with “drilling long footage with drill tools combined in multi-cylinders” was achieved at deep coring section. Four world drilling records were created which include more than a thousand meters continuous coring at φ311 mm, and the footage per roundtrip footage at φ311 mm, φ216 mm and φ152 mm is all more than 30 m, all of these breakthroughs reduced at least 300 days for this project; moreover, considering the characteristics of formations that the geothermal gradient is high in the drilled sections and the inside-well temperature is over 240°C after drilling completion, a formate-polymer water-based mud system was developed by compounding attapulgite and sodium bentonite and by adding independently developed high-temperature stabilizer, which can provide critical technical support for successful well completion at 7018 m in the super-high-temperature environment It is the first time that the water-based mud is operated at the working temperature higher than 240°C in China; Besides, considering the high-quality requirement on cores imposed by the project, the method “mechanical cored is charge” to discharge core nondestructively on the ground was worked out, and more than 4000 m scatheless cores were discharged out of the drill pipes while maintaining original stratum structures.  相似文献   

Mapping cropland fallow areas in myanmar to scale up sustainable intensification of pulse crops in the farming system     

Murali Krishna Gumma  Prasad S Thenkabail  Kumara Charyulu Deevi  Irshad A Mohammed  Pardhasaradhi Teluguntla  Adam Oliphant 《地理信息系统科学与遥感》2018,55(6):926-949

Cropland fallows are the next best-bet for intensification and extensification, leading to increased food production and adding to the nutritional basket. The agronomical suitability of these lands can decide the extent of usage of these lands. Myanmar’s agricultural land (over 13.8 Mha) has the potential to expand by another 50% into additional fallow areas. These areas may be used to grow short-duration pulses, which are economically important and nutritionally rich, and constitute the diets of millions of people as well as provide an important source of livestock feed throughout Asia. Intensifying rice fallows will not only improve the productivity of the land but also increase the income of the smallholder farmers. The enhanced cultivation of pulses will help improve nutritional security in Myanmar and also help conserve natural resources and reduce environmental degradation. The objectives of this study was to use remote sensing methods to identify croplands in Myanmar and cropland fallow areas in two important agro-ecological regions, delta and coastal region and the dry zone. The study used moderate-resolution imaging spectroradiometer (MODIS) 250-m, 16-day normalized difference vegetation index (NDVI) maximum value composite (MVC), and land surface water index (LSWI) for one 1 year (1 June 2012–31 May 2013) along with seasonal field-plot level information and spectral matching techniques to derive croplands versus cropland fallows for each of the three seasons: the monsoon period between June and October; winter period between November and February; and summer period between March and May. The study showed that Myanmar had total net cropland area (TNCA) of 13.8 Mha. Cropland fallows during the monsoon season account for a meagre 2.4% of TNCA. However, in the winter season, 56.5% of TNCA (or 7.8 Mha) were classified as cropland fallows and during the summer season, 82.7% of TNCA (11.4 Mha) were cropland fallows. The producer’s accuracy of the cropland fallow class varied between 92 and 98% (errors of omission of 2 to 8%) and user’s accuracy varied between 82 and 92% (errors of commission of 8 to 18%) for winter and summer, respectively. Overall, the study estimated 19.2 Mha cropland fallows from the two major seasons (winter and summer). Out of this, 10.08 Mha has sufficient moisture (either from rainfall or stored soil water content) to grow short-season pulse crops. This potential with an estimated income of US$ 300 per hectare, if exploited sustainably, is estimated to bring an additional net income of about US$ 1.5 billion to Myanmar per year if at least half (5.04 Mha) of the total cropland fallows (10.08 Mha) is covered with short season pulses.  相似文献