浙南近海虾类群落结构及其多样性分析   总被引：1，自引：0，他引：1  

陈伟峰  彭欣  叶深  谢起浪  陈少波  汪振华  陈骁 《海洋科学》2018,42(3):37-45

作者根据2015年11月(秋季)、2016年2月(冬季)、2016年5月(春季)和2016年8月(夏季)对浙南近海进行的渔业资源调查数据,用生物量作为虾类资源分布的数量指标,对该海域虾类的组成、数量分布以及季节变化进行分析。结果显示:该区域共鉴定出虾类30种,隶属于10科21属,以对虾科(Penaeidae)虾类最多,其次为管鞭虾科(Solenoceridae),长臂虾科(Palaemonida)位居第3位。按季节来看,秋季共鉴定虾类27种,各站位平均生物量为6.97 kg/km2,优势种为凹陷管鞭虾(Solenocera koelbeli)、中国毛虾(Acetes chinensis)和中华管鞭虾(Solenocera crassicornis)等3种;冬季鉴定出虾类25种,平均生物量为1.65 kg/km2,优势种为凹陷管鞭虾、扁足异对虾(Atypopenaeus stenodactylus)、日本鼓虾(Alpheus japonicus)、鲜明鼓虾(Alpheus digitalis)、中国毛虾、中华管鞭虾和周氏新对虾(Metapenaeus joyneri)等7种;春季20种,平均生物量为2.22 kg/km2,优势种为戴氏赤虾(Metapenaeopsis dalei)、东海红虾(Metapenaeopsis dalei)和中华管鞭虾等3种;夏季16种,平均生物量为10.36 kg/km2,优势种有鹰爪虾(Trachysalambria curvirostris)和中华管鞭虾等2种。Margalef丰富度指数(D)、Shannon-Wiener多样性指数(H′)和Pielou均匀度指数(J′)秋季均低于冬季。秋冬季受到浙闽沿岸流影响,温度、盐度相对较低,夏季受到台湾暖流外侧影响,温度、盐度相对较高,且各季节间由于瓯江、椒江、飞云江、鳌江等陆源性冲淡水的影响,盐度、温度变化相对较大,使得该区域的物种不得不适应一个跨度较大的温盐范围,广温广盐性种类为主。  相似文献   

利用超快速精密星历约束的北斗卫星实时精密定轨     

范磊  施闯  李敏 《大地测量与地球动力学》2018,38(9):937-942

以广播星历为起算轨道的北斗卫星实时滤波精密定轨往往需要较长收敛时间，针对此，提出利用超快速精密星历约束的实时精密定轨方法。通过MGEX跟踪网全球分布的51个测站连续7 d的实测数据，利用平方根信息滤波对北斗卫星实时精密轨道进行确定，并以3 d解事后轨道作为参考，评估北斗卫星实时滤波轨道精度。结果表明，利用广播星历作起算轨道时，北斗实时滤波轨道平均需要经过15 h收敛才能达到稳定，而新方法在这段时间内轨道变化较为平稳，未出现明显的收敛现象，并且7 d时间内GEO卫星在切向、法向和径向上RMS分别优于2.5 m、20 cm和30 cm，IGSO和MEO卫星在3个方向上分别优于30 cm、15 cm和10 cm。
  相似文献   

典型深街谷内树木空间配置对行人呼吸高度处气流的影响     

林定  申小云  朱勇兵  陈崇成 《地球信息科学学报》2018,20(9):1235-1243

为揭示树木的不同空间配植方案对行人呼吸高度气流的影响,本文将树木视为均匀多孔介质,通过附加源项法从空气动力学角度用CFD模拟了H/W=2的典型深街谷几何内4种树木配植情景,实验表明,不同空间配置下树木对街谷内行人呼吸高度处局地气流的影响强弱在空间分布模式上差异悬殊：① 均匀种植的树木对街谷内行人呼吸高度的气流起到阻碍作用,不均匀种植则有效提升街谷的整体流速。4种空间配植方案下树木对气流的影响程度不同,阻碍作用从大到小的顺序为均匀间距8 m（Spa8m）>均匀间距6 m（Spa6m）>均匀间距20 m（Spa20m）>不均匀配植（Non-uniform）;对应的平均气流增强指标顺序为$\bar{D}_{spa8}$（-19.31%）<$\bar{D}_{spa6}$（-16.14%）<$\bar{D}_{spa20}$（-10.73%）<$\bar{D}_{non-uniform}$（1.25%）。② 对比不均匀和均匀的种植方案,不均匀植树的街谷内部行人呼吸高度的气流流速比其对照案例（均匀植树Spa8m方案）整体增强了106.49%。街谷中部不种树,在街谷两端配置树木并预留足够的自由空间的不均匀植树方案,能够让角涡渗入街谷中部,促使街谷内部的垂直漩涡和两端的水平角涡运动,增强湍流和垂直交换,有效减少了街道两端“风口效应”和街道中部“风影效应”的区域,改善了整个街谷行人呼吸平面的风环境。④ 合理空间配置的树木能够改善街谷内部的行人风环境。街谷内行人呼吸高度处的气流对局地条件很敏感,树木的局部配置（空间簇集、密度）将引起强烈的空间变化。在既有城市建筑布局条件下,如何通过谨慎的景观设计,利用树木等城市绿化措施有效地改善城市的行人风环境,缓解污染扩散、疾病传播等问题,本文的方法可提供一定的参考。  相似文献   

基于高斯两步移动搜寻法的村镇避难场所可达性研究     

但文羽  肖映辉  胡周灵  詹庆明 《地球信息科学学报》2018,20(10):1412-1421

避难场所可达性是指避难场所与受灾居民之间的通达性,即灾害发生时,避难人员通过避难疏散通道到达避难场所的难易程度,是评价避难场所布局合理性的重要指标。本研究结合高斯两步移动搜寻法和网络分析法,从供需双向出发对村镇地区避难场所进行可达性分析。2种方法的结合,既充分考虑了需求点与设施点的相互作用,又充分考虑了设施点的吸引力随距离的衰减关系,并基于实际道路,以步行疏散时间作为搜索半径,降低了传统研究中因忽略供需间相互作用及实际距离而引起的可达性结果的误差。最后,以神农架松柏镇区为例,验证该方法的实际应用价值。结果表明,该方法能够有效测定村镇地区避难场所的空间可达性,同时,基于GIS软件可以直观地揭示研究区域内避难场所可达性空间分布差异。该方法可为制定科学的村镇防灾减灾规划提供方法支持。  相似文献   

非线性波消波及波场分布研究   总被引：1，自引：1，他引：0  

王巧莎  李明海 《海洋科学》2018,42(6):30-38

本文基于雷诺平均N-S方程,并结合RNG k-e方程建立了粘性数值波浪水槽,对不同波陡、不同相对水深、不同相对波高的非线性规则波的阻尼消波问题和波场分布进行研究。文中提出了两种描述消波区内部阻尼变化的阻尼函数,分别适用于小波陡情形和高波陡情形。研究结果表明,小波陡组消波区可设为一个波长,阻尼系数取10~4～10~5即可满足消波要求,计算结果与实验结果及造波理论吻合良好;高波陡组消波区可设为两个波长,阻尼系数取10~4～10~5亦可满足消波要求,计算结果与实验结果吻合良好。此外,当波陡较小时,波场内反射情况的小幅改变即可对整个波场造成影响,特别是当水深较浅时这种影响极为明显,需谨慎考虑。当波陡较大时,水波能量较高,整个波场沿水波传播方向可观测到明显的衰减现象,在具体试验中需进行考虑。  相似文献   

Bearing capacity of offshore umbrella suction anchor foundation in silty soil under varying loading modes     

Qi Yang  Guanglai Pan  Quandi Wang 《Marine Georesources & Geotechnology》2018,36(7):781-794

Considering the current disadvantages of present offshore wind turbine foundations, a novel anchor foundation with skirt and branches is proposed, called offshore umbrella suction anchor foundation (USAF). A series of experiments and numerical simulations were performed to explore the bearing capacity of the USAF under various kinds of loading modes. The bearing characteristics and the anchor–soil interactions are described in detail for horizontal static loading, horizontal cyclic loading, and an antidrawing (pullout) test in silty soil. In the static loading test, the load–deflection of the anchor under step loading was analyzed and the normalized curve of the load–deflection was obtained to determine the ultimate horizontal bearing capacity of the anchor under normal working conditions. Under horizontal cyclic loading, the relationship between the plastic cumulative deformation and cyclic number was determined. In addition, the responses of USAF were investigated for a low wave frequency and storm surges. In the drawing test, it was found that a “segmentation phenomenon” occurred during the test. Moreover, a method to identify the maximum antidrawing load of USAF was provided based on dynamic mechanics. The numerical results show that the use of anchor branches and skirt can enhance the bearing performance of USAF to a certain degree. However, the anchor branch has a slight positive influence on the bearing performance improvement. The USAF is not only similar to a stiff short pile, but a rotation occurs. The failure envelope under composite loading (V-M) was obtained and the changes associated with changes in the aspect ratio of the internal compartment were clarified.  相似文献   

基于GIS的石家庄市雾霾分析     

苏亚聪  史娟  徐爽 《北京测绘》2020,(2):233-237

为了得出雾霾气象成因机制、影响因素和时空分布特征,以石家庄市区与郊县为研究区域,将2013年9月至2016年12月石家庄市各市区、郊县的PM2.5历史监测数据中的有效数据进行了数据分析处理得到雾霾浓度数据,还有温度、降水、风速、地形和人口密度等数据,运用GIS分析的方法,模拟绘制石家庄雾霾的时空分布图、雾霾与各影响因子的专题对比图,得到雾霾形成机制的因子、雾霾的时空分布规律、雾霾季节变化特征、雾霾与地形间的关系等;运用数据分析软件OriginPro8.SR3分析雾霾浓度与风速数据、降雨数据、温度数据间的相关性。  相似文献   

利用短期静态PPP结果反演海潮负荷位移     

魏国光  王琪洁  彭葳  郭良琦 《大地测量与地球动力学》2019,39(6):607-612

采用香港11个GPS测站的观测资料进行1 h、2 h、3 h和4h静态PPP解算，获得4组PPP坐标序列，利用调和分析求取11个测站处8个主要分潮的负荷位移参数（振幅和相位），将其与海潮模型计算的负荷位移参数进行对比，并比较分析PPP反演值与海潮模型值改正海潮负荷信号的效果。结果表明，垂直和水平方向上，不同PPP结果反演8个分潮的负荷位移分别具有约5 mm和7 mm的差异；PPP反演8个分潮垂向负荷位移优于全球海潮模型，但水平方向上的反演效果稍弱。  相似文献   

Solution for a plane strain rough‐walled hydraulic fracture driven by turbulent fluid through impermeable rock          下载免费PDF全文

N. Zolfaghari  E. Dontsov  A. P. Bunger 《国际地质力学数值与分析法杂志》2018,42(4):587-617

The impact of turbulent flow on plane strain fluid‐driven crack propagation is an important but still poorly understood consideration in hydraulic fracture modeling. The changes that hydraulic fracturing has experienced over the past decade, especially in the area of fracturing fluids, have played a major role in the transition of the typical fluid regime from laminar to turbulent flow. Motivated by the increasing preponderance of high‐rate, water‐driven hydraulic fractures with high Reynolds number, we present a semianalytical solution for the propagation of a plane strain hydraulic fracture driven by a turbulent fluid in an impermeable formation. The formulation uses a power law relationship between the Darcy‐Weisbach friction factor and the scale of the fracture roughness, where one specific manifestation of this generalized friction factor is the classical Gauckler‐Manning‐Strickler approximation for turbulent flow in a rough‐walled channel. Conservation of mass, elasticity, and crack propagation are also solved simultaneously. We obtain a semianalytical solution using an orthogonal polynomial series. An approximate closed‐form solution is enabled by a choice of orthogonal polynomials embedding the near‐tip asymptotic behavior and thus giving very rapid convergence; a precise solution is obtained with 2 terms of the series. By comparison with numerical simulations, we show that the transition region between the laminar and turbulent regimes can be relatively small so that full solutions can often be well approximated by either a fully laminar or fully turbulent solution.  相似文献   

Wave tank and bench-top control testing of a wave energy converter     

《Applied Ocean Research》2019

An increasing number of experiments are being conducted to study the design and performance of wave energy converters. Often in these tests, a real-time realization of prospective control algorithms is applied in order to assess and optimize energy absorption as well as other factors. This paper details the design and execution of an experiment for evaluating the capability of a model-scale WEC to execute basic control algorithms. Model-scale hardware, system, and experimental design are considered, with a focus on providing an experimental setup capable of meeting the dynamic requirements of a control system. To more efficiently execute such tests, a dry bench testing method is proposed and utilized to allow for controller tuning and to give an initial assessment of controller performance; this is followed by wave tank testing. The trends from the dry bench test and wave tank test results show good agreement with theory and confirm the ability of a relatively simple feedback controller to substantially improve energy absorption. Additionally, the dry bench testing approach is shown to be an effective and efficient means of designing and testing both controllers and actuator systems for wave energy converters.  相似文献