不等高输电塔线体系风致动力响应分析   总被引：1，自引：0，他引：1  

陈俊旗  王伟 《震灾防御技术》2010,5(3):358-363

以山区常用输电塔5A-ZBC2为基础,建立了山区的不等高输电塔线体系。考虑到高差的不断变化以及不同方向攻角风荷载的作用,运用随机模拟风振分析方法对其进行了分析。结果表明,位于山顶的输电塔顶位移均值最大;位于山坡的次之;而位于山底的最小。而对不平衡张力来说,位于山坡的塔所受的不平衡张力最大;位于山顶的塔次之;位于山底的塔最小。随着高差的增大,塔顶位移和不平衡张力增大。塔顶位移主要受导线风荷载影响,而塔顶速度和加速度与塔的一阶振型有关,导线振动与荷载激励相关。  相似文献   

Simulating coseismic deformation of quartz in the middle crust and fabric evolution during postseismic stress relaxation — An experimental study   总被引：3，自引：0，他引：3  

Claudia A. Trepmann  Bernhard Stckhert  Dorothe Dorner  Rasoul Hamidzadeh Moghadam  Martina Küster  Klaus Rller 《Tectonophysics》2007,442(1-4):83-104

Non-steady state deformation and annealing experiments on vein quartz are designed to simulate earthquake-driven episodic deformation in the middle crust. Three types of experiments were carried out using a modified Griggs-type solid medium deformation apparatus. All three start with high stress deformation at a temperature of 400 °C and a constant strain rate of 10^− 4 s^− 1 (type A), some are followed by annealing in the stability field of α-quartz for 14–15 h at zero nominal differential stress and temperatures of 800–1000 °C (type A + B), or by annealing for 15 h at 900 °C and at a residual stress (type A + C).The quartz samples reveal a very high strength > 2 GPa at a few percent of permanent strain. The microstructures after short-term high stress deformation (type A) record localized brittle and plastic deformation. Statisc annealing (type A + B) results in recrystallisation restricted to the highly damaged zones. The new grains aligned in strings and without crystallographic preferred orientation, indicate nucleation and growth. Annealing at non-hydrostatic conditions (type A + C) results in shear zones that also develop from deformation bands or cracks that formed during the preceding high stress deformation. In this case, however, the recrystallised zone is several grain diameters wide, the grains are elongate, and a marked crystallographic preferred orientation indicates flow by dislocation creep with dynamic recrystallisation. Quartz microstructures identical to those produced in type A + B experiments are observed in cores recovered from Long Valley Exploratory Well in the Quaternary Long Valley Caldera, California, with considerable seismic activity.The experiments demonstrate the behaviour of quartz at coseismic loading (type A) and subsequent static annealing (type A + B) or creep at decaying stress (type A + C) in the middle crust. The experimentally produced microfabrics allow to identify similar processes and conditions in exhumed rocks.  相似文献   

A laboratory experiment to monitor the contact state of a fault by transmission waves   总被引：1，自引：0，他引：1  

Naoto Yoshioka  Koji Iwasa 《Tectonophysics》2006,413(3-4):221-238

We performed a series of laboratory experiments in which elastic waves were transmitted across a simulated fault. Two types of experiments were carried out: (1) Normal Stress Holding Test (NSHT): normal stress was kept constant for about 3 h without shear stress and transmission waves were observed. (2) Shear Stress Increasing Test (SSIT): shear stress was gradually increased until a stick-slip event occurred. Transmission waves were continuously observed throughout the process of stress accumulation. We focused on the change in transmission waves during the application of shear stress and especially during precursory slips.It was found in NSHT that the amplitude of transmission waves linearly increased with the logarithm of stationary contact time. The increase amounted to a few percent after about 3 h. Creep at asperity contacts is responsible for this phenomenon. From a theoretical consideration, it was concluded that the real contact area increased with the logarithm of stationary contact time.We observed in SSIT a significant increase in wave amplitude with shear stress application. This phenomenon cannot be attributed to the time effect observed in NSHT. Instead, it can be explained by the mechanism of “junction growth” proposed by Tabor. Junction growth yields an increase in real contact area. It is required for junction growth to occur that the material in contact is already plastic under a purely normal loading condition. A computer simulation confirmed that this requirement was satisfied in our experiments. We also found that the rate at which the amplitude increased was slightly reduced prior to a stick-slip event. The onset time of the reduction well coincides with the onset of precursory slip. The cause of the reduction is attributed to the reset of stationary contact time due to displacement. This interpretation is supported by the result of NSHT. Taking the time of stationary contact in SSIT into account, we may expect the change in wave amplitude to be, at most, only a few percent. The observed slight reduction in increasing rate is, in this sense, reasonable. The static stiffness of the fault also decreases with precursory slip. It was also found that low frequency waves are a better indicator of precursory slip than high frequency waves. This might suggest that low frequency waves with longer wavelength are a better indicator of average behavior of faults. The problem, however, merits a further investigation. The shifts in phase were also found to be a good indicator of the change in contact state of the fault. The changes in both amplitude and phase of transmission waves are unifyingly understood through the theory of transmission coefficient presented by Pyrak-Nolte et al. Rough surfaces have a tendency to give larger stick-slips than smooth surfaces. The amount of precursory slip is larger for rough surfaces than for smooth surfaces. Although it was confirmed by a computer simulation that rough surfaces have larger contact diameters than smooth surfaces, the rigorous relationship between the surface roughness (contact diameter) and the amount of precursory slips was not established.  相似文献   

Shear waves at a corrugated interface between anisotropic elastic and visco-elastic solid half-spaces     

S. K. Tomar  Jatinder Kaur 《Journal of Seismology》2007,11(3):235-258

Rayleigh’s method of approximation is employed to find out the reflection and transmission coefficients due to an incident plane SH wave at a corrugated interface between a laterally and vertically inhomogeneous anisotropic elastic solid half-space and a laterally and vertically inhomogeneous isotropic visco-elastic solid half-space. The lateral and vertical inhomogeneities are described by the exponential variations of elastic parameters. The formulae of reflection and transmission coefficients are derived in closed form for the first-order approximation of the corrugation. The effects of the corrugation of the interface, the inhomogeneity, the anisotropy, the visco-elasticity and the frequency of the incident wave on these coefficients are studied analytically and numerically for a specific model containing a periodic interface. The results of earlier workers have been reduced as particular cases from the present formulation.  相似文献   

Java多线程及多点连接技术在WebGIS数据传输中的应用     

Peng Zhuangzhi Yu Xin School of Remote Sensing  Information Engineering  Wuhan University  Luoyu Road  Wuhan  China 《测绘科技情报》2007,(1)

目前空间数据的传输效率低下已成为制约WebGIS发展的主要瓶颈之一。多线程技术以及多点连接在提高系统吞吐率、有效利用系统资源、改善用户任务之间的通信效率等方面有着显著作用。本文采用地图分层和图面分割的方法以及Java多线程和多点连接技术实现了WebGIS空间数据的高效传输。  相似文献   

A numerical study on 2-D compressive wave propagation in rock masses with a set of joints along the radial direction normal to the joints   总被引：1，自引：0，他引：1  

W.D. Lei  A.M. Hefny  S. Yan  J. Teng 《Computers and Geotechnics》2007,34(6):508-523

An explosion in a borehole or an accidental explosion in a tunnel will generate a two-dimensional (2-D) compressive wave that travels through the surrounding rock mass. For the problem of 2-D compressive wave propagation in a rock mass with parallel joints in the radial direction normal to the joints, parametric studies on the transmission ratio and the maximum rebound ratio are performed in universal distinct element code. The variation of the transmission ratio with the ratio of joint spacing to wavelength is generalized into a characteristic curve, which can be used as a prediction model for estimating the transmission ratio. The relationship between the maximum rebound ratio and the influence factors is obtained in charts. The charts can be used as a prediction model for estimating the maximum rebound ratio. The proposed prediction models for estimating the transmission ratio and the maximum rebound ratio are applied to a field explosion test, Mandai test in Singapore. The minimum possible values of peak particle velocity (PPV) at the monitoring points are estimated by using the proposed prediction model for estimating the transmission ratio along the radial direction normal to the joints. On the other hand, the maximum possible values of PPV are estimated by using the proposed prediction model for estimating the maximum rebound ratio along the same radial direction. The comparison shows a good agreement between the field-recorded PPVs and the estimated range of PPVs given by the minimum possible PPVs and the maximum possible PPVs at the monitoring points in Mandai test. The good agreement between the estimated and field-recorded values validates the proposed prediction models for estimating peak particle velocity in a rock mass with a set of joints due to application of a compressive wave at the boundary of a tunnel or a borehole.  相似文献   

Hydrous olivine (Mg_{1? y?} Fe²⁺_y)_{2? x} ?v _x ? SiO₄H_{2 x} – a new DHMS phase of variable composition observed as nanometer-sized precipitations in mantle olivine     

N. R. Khisina  R. Wirth 《Physics and Chemistry of Minerals》2002,29(2):98-111

 An olivine grain from a peridotite nodule 9206 (Udachnaya kimberlite, Siberia) was investigated by TEM methods including AEM, HRTEM, SAED and EELS techniques. A previous study of the 9206 olivine sample revealed OH absorption bands in the IR spectrum and abundant nanometer-sized OH-bearing inclusions, of hexagonal-like or lamellar shape. Inclusions, which are several hundred nm in size, consist of 10 ? phase, talc and serpentine (chrysotile and lizardite). The lamellar (LI) and hexagon-like small inclusions of several ten nm in size (SI) are the topic of the present paper. AEM investigations of the inclusions reveal Mg, Fe and Si as cations only. The Mg/Si and Fe/Si atomic ratios are lower in the inclusions than in the host olivine. The Si concentration in the olivine host and both lamellar inclusions and small inclusions is the same. A pre-peak at 528eV was observed in EEL spectra of LI and SI, which is attributed to OH⁻ or Fe³⁺. From these data it is concluded that there is a OH⁻- or Fe³⁺-bearing cation-deficient olivine-like phase present. HRTEM lattice fringe images of LI and SI exhibit modulated band-like contrasts, which are superimposed onto the olivine lattice. Diffraction patterns (Fourier-transforms) of the HREM images as well as SAED patterns show that the band-like contrasts in HRTEM images of the inclusions are caused by periodic modulations of the olivine lattice. Three kinds of superperiodicity in the olivine structure such as 2a, 3a and 3c, were observed in SAED patterns. The corresponding olivine supercells labelled here as Hy-2a, Hy-3a and Hy-3c were derived. The M1-vacancies located in the (100) and (001) octahedral layers of the olivine lattice are suggested to form ordered arrays of planar defects (PD), which cause the band-like contrasts in HRTEM patterns as well as the superperiodicity in the SAED patterns. The vacancy concentrations as well as the chemical composition of Hy-2a, Hy-3a and Hy-3c olivine supercells were calculated using crystal chemical approaches, assuming either {(OH)^< _O−V^" _Me−(OH)^< _O}^↔, or {F e ^< _Fe −H _Me ^′}^↔ or {2F e ^< _Fe −V _Me ^"}^↔ point defect associates. The calculated theoretical compositions Mg_1.615Fe⁺² _0.135v_0.25SiO₄H_0.5 (Hy-2a) and Mg_1.54Fe²⁺ _0.12v_0.33SiO₄H_0.66 (Hy-3a and Hy-3c) are in a good agreement with the AEM data on inclusions. Hy-2a, Hy-3a and Hy-3c are considered to be a hydrous olivine with the extended chemical formula (Mg_1-yFe²⁺ _y)_2−xv_xSiO₄H_2x. The crystal structure of hydrous olivine is proposed to be a modular olivine structure with Mg-vacant modules. The crystal chemical formula of hydrous olivines in terms of a modular structure can be written as [MgSiO₄H₂] · 3[Mg_1.82Fe_0.18SiO₄] for Hy-2a, [MgSiO₄H₂] · 2[Mg_1.82Fe_0.18SiO₄] for Hy-3a and Hy-3c. Hydrous olivine is suggested to be exsolved from the olivine 9206, which has been initially saturated by OH-bearing point defects. The olivine 9206 hydration as well as the following exsolution of hydrous olivine inclusions is suggested to occur at high pressure-high temperature conditions of the upper mantle. Received: 15 January 2001 / Accepted: 2 July 2001  相似文献   

深层水泥土搅拦桩在软土地基处理中的应用     

何元斌  李燕 《云南地质》2004,23(2):273-277

通过对深层水泥土搅拌桩的加固机理及复合地基承载力性状的简要分析,根据国家现行规范,结合具体地基处理工程实例,对深层水泥搅拌桩在软土地区地基加固处理中的方案选择、设计、施工及检测中的常见技术要点作初步探讨。  相似文献   

用远场辐射场反演云闪放电参数   总被引：2，自引：0，他引：2  

祝宝友  陶善昌  马明  吕伟涛 《气象学报》2004,62(4):498-503

用地面电磁场遥感闪电放电参数无论是在实际应用还是理论研究中都具有重要意义。文中基于电流传输线模式 ,提出了一种用单站远场VLF/LF辐射场反演云内放电参数的简便方法。当传输线电流从底部传播到顶部的时间只有几微秒时 ,整个传输线的VLF/LF辐射可以近似成偶极子辐射 ,即远场辐射场与电流的时间变化率和传输线长度的乘积成正比。因此 ,对远场辐射场做时间积分就能获得完整的电流矩波形 (上升沿有所加宽 ) ,而且传输线模式中的重要参数 ,电流从底部传播到顶端经历的时间 ,也可以近似地用辐射场时间积分幅度与辐射场幅度之比来估计。这一方法具有估计云闪双极性大脉冲辐射过程的放电参数的潜力。  相似文献   

Characteristics and genesis of maghemite in Chinese loess and paleosols: Mechanism for magnetic susceptibility enhancement in paleosols   总被引：4，自引：0，他引：4  

Tianhu Chen  Huifang Xu  Qiaoqin Xie  Jun Chen  Junfeng Ji  Huayu Lu 《Earth and Planetary Science Letters》2005,240(3-4):790-802

Morphological characteristics and microstructures of magnetic minerals extracted from Chinese loess and paleosols were investigated using powder X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM). Our results indicate that maghemite in loess–paleosol sequences was transformed from magnetite through oxidation of magnetite. Maghemite transformed from eolian magnetite during chemical weathering has low-angle grain boundaries among maghemite nano-crystals. Some nano-crystalline maghemites with nanoporous texture resulted from microbe-induced precipitation of magnetite or transformation of poorly crystalline ferric Fe (oxy)hydroxides in presence of Fe-reducing bacteria. Aggregates of euhedral maghemite nano-crystals were transformed from magnetite magnetosomes. Both microbe-induced nanoporous magnetite and microbe-produced magnetite magnetosomes are directly related to microbial activities and pedogenesis of the paleosols. It is proposed that the formation of nano-crystalline maghemite with superparamagnetic property in paleosol results in the enhancement of magnetic susceptibility, although the total amount (weight percent) of magnetic minerals in both paleosol and loess units is similar. Our results also show that nano-crystalline and nanoporous magnetite grains prefer to transform into maghemite in semi-arid soil environments instead of hematite, although hematite is a thermodynamically stable phase. This result also indicates that a decrease in crystal size will increase stability of maghemite. It is also inferred that surface energy of maghemite is lower than that of hematite.  相似文献