Using the applied element method for modelling calcium silicate brick masonry subjected to in‐plane cyclic loading     

Daniele Malomo  Rui Pinho  Andrea Penna 《地震工程与结构动力学》2018,47(7):1610-1630

The response of calcium silicate unreinforced masonry construction to horizontal cyclic loading has recently become the focus of experimental and numerical research, given its extensive use in some areas of the world that are now exposed to induced earthquakes (eg, north of the Netherlands). To assess the seismic behaviour of such construction, a relatively wide range of modelling methodologies are available, amongst which the discrete elements approach, which takes into account the intrinsic heterogeneity of a brick‐mortar assembly, can probably be deemed as the most appropriate computational procedure. On the other hand, however, since discrete elements numerical methods are based on a discontinuum domain, often they are not able to model every stage of the structural response adequately, and because of the high computational burden required, the analysis scale should be chosen carefully. The applied element method is a relatively recent addition to the discrete elements family, with a high potential for overcoming the aforementioned limitations or difficulties. Initially conceived to model blast events and concrete structures, its use in the earthquake engineering field is, of late, increasing noticeably. In this paper, the use of the applied element method to model the in‐plane cyclic response of calcium silicate masonry walls is discussed and scrutinised, also through the comparison with experimental results of in‐plane cyclic shear‐compression tests on unreinforced masonry walls.  相似文献   

椭圆度-凹坑双缺陷海底管道局部屈曲特性研究   总被引：2，自引：1，他引：1  

薛陆丰  余杨  余建星  徐立新  高静坤  刘浩 《海洋工程》2018,36(2):92-99

海底管道在制造、埋设以及使用过程中极易产生椭圆度-凹坑双缺陷,双缺陷影响管道局部屈曲,对含椭圆度-凹坑双缺陷海底管道的局部屈曲特性研究十分必要。现行规范中采用等效椭圆度对含椭圆度-凹坑海底管道进行评估,该方法无法准确评估不同缺陷形式的屈曲特性。采用形状系数对含椭圆度-凹坑双缺陷的海底管道进行评估,运用有限元软件ABAQUS进行数值模拟,并进行试验验证。在此基础上对含有不同凹坑深度、不同椭圆度的海底管道进行局部屈曲的数值模拟,计算不同形状椭圆度、含有不同凹坑深度海底管道的形状系数,对其进行敏感性分析。计算结果表明:形状系数对海底管道椭圆度、凹坑深度、径厚比敏感性较强;对凹坑宽度敏感性较弱。  相似文献   

东太平洋海隆13°N表层含金属沉积物物质组成与元素赋存状态     

荣坤波  曾志刚  武力  李康 《海洋科学》2018,42(7):70-79

为了解不同类型含金属沉积物在物质组成和元素赋存状态的差异,对东太平洋海隆13°N洋中脊两侧表层含金属沉积物(站号:E271和E53)进行了矿物学、地球化学分析,顺序提取实验,并与前人对轴部表层沉积物(站号:17A-EPR-TVG1)的研究结果作了对比分析。研究结果表明, E271和E53是远端含金属沉积物,由非浮力热液羽状流中颗粒物沉降所形成的;17A-EPR-TVG1沉积物是近喷口含金属沉积物,由黑烟囱或者热液硫化物丘状体崩塌、堆积,或者由热液羽状流中Fe-Mn氧化物和硫化物快速沉淀而形成的,近喷口沉积物比远端沉积物更富集Fe、Cu和Zn等元素。元素在两种含金属沉积物中的赋存状态基本相同,除了Fe,Cu,Zn,Mo和稀土元素(REE)等元素在远端沉积物中主要存在于Fe-Mn氧化物相,在近喷口沉积物中主要在残留相中。远端沉积物中REE页岩标准化配分模式与海水相似,表明REE主要来自海水,而近喷口沉积物中REE配分模式与热液流体相似,说明REE以高温热液流体来源为主。相关研究结果加深了对热液沉积作用研究的认识。  相似文献   

圆柱形支撑大跨度建筑结构强震冲击分析模型仿真   总被引：3，自引：2，他引：1       下载免费PDF全文

吴海波  王新妮 《地震工程学报》2018,40(1):48-53

圆柱形支撑大跨度建筑稳定性较差,不能在强震冲击下保持稳定的结构状态。为解决此问题,设计圆柱形支撑大跨度建筑结构强震下冲击分析仿真模型,通过圆柱分析法则的确定、有限元支撑模拟分析与监测、圆柱形支撑体系承载能力分析以完成模型的仿真分析与监测。基于此对大跨度建筑结构强震冲击进行静力分析,调整强震冲击下模型的结构,完成模型的搭建。模拟强震冲击环境,设计对比实验结果表明,应用圆柱形支撑大跨度建筑结构强震下冲击分析仿真模型,可明确圆柱形支撑大跨度建筑薄弱点,发现稳定性较差建筑结构单元,达到提升圆柱形支撑大跨度建筑在强震冲击下稳定性的目的。  相似文献   

Influence of seismic motions on behavior of piles in liquefied soils          下载免费PDF全文

Kaustav Chatterjee  Deepankar Choudhury 《国际地质力学数值与分析法杂志》2018,42(3):516-541

In the present study an analytical procedure based on finite element technique is proposed to investigate the influence of vertical load on deflection and bending moment of a laterally loaded pile embedded in liquefiable soil, subjected to permanent ground displacement. The degradation of subgrade modulus due to soil liquefaction and effect of nonlinearity are also considered. A free headed vertical concrete elastic nonyielding pile with a floating tip subjected to vertical compressive loading, lateral load, and permanent ground displacement due to earthquake motions, in liquefiable soil underlain by nonliquefiable stratum, is considered. The input seismic motions, having varying range of ground motion parameters, considered here include 1989 Loma Gilroy, 1995 Kobe, 2001 Bhuj, and 2011 Sikkim motions. It is calculated that maximum bending moment occurred at the interface of liquefiable and nonliquefiable soil layers and when thickness of liquefiable soil layer is around 60% of total pile length. Maximum bending moment of 1210 kNm and pile head deflection of 110 cm is observed because of 1995 Kobe motion, while 2001 Bhuj and 2011 Sikkim motions amplify the pile head deflection by 14.2 and 14.4 times and bending moment approximately by 4 times, when compared to nonliquefiable soil. Further, the presence of inertial load at the pile head increases bending moment and deflection by approximately 52% when subjected to 1995 Kobe motion. Thus, it is necessary to have a proper assessment of both kinematic and inertial interactions due to free field seismic motions and vertical loads for evaluating pile response in liquefiable soil.  相似文献   

大连贺家圈黄土粒度所指示的物源特征     

郑树森  李永化  魏东岚 《云南地理环境研究》2020,(1):41-47

基于大连长兴岛的一套完整的晚更新世黄土剖面(贺家圈剖面),应用端元分析模型,对所采集的21个沉积样品的粒度数据进行分析。结论认为:从贺家圈剖面沉积物粒级组分中可以分离出3个代表不同沉积动力以及改造作用的沉积端元组分。并结合地球化学元素的对比分析,初步认为:端元1可能代表了剖面原始的粒度沉积组分,主峰为近源沉积,次峰为远源沉积;端元2可能代表了沉积物在沉积之后受到的淋溶作用和残积作用;端元3可能代表的是沉积物沉积之后受到的化学风化作用。  相似文献   

利用盐湖常见元素的助烧结作用绿色制备氧化镁及磷酸镁水泥          下载免费PDF全文

李颖  董金美  肖学英  郑卫新  文静  常成功 《盐湖研究》2020,28(2):15-25

低活性氧化镁是制备磷酸镁水泥(MPC)的关键原材料。现行低活性氧化镁的生产方式导致了制备MPC具有能耗高和成本高的缺点,不利于其推广应用。利用盐湖中常见元素如B,Na、K和Cl的助烧结作用,在≤1 200℃煅烧盐湖提锂镁渣、外掺B的轻烧镁粉和水氯镁石的热解产物制备低活性氧化镁。介绍了低活性氧化镁的粒径、比表面积、孔隙率、化学组成、矿物组成和形貌等物理特征,以及低活性氧化镁制备MPC的凝结时间、水化产物、微观结构、抗压强度、体积稳定性等凝结硬化性能,并分析了烧结温度对低活性氧化镁的理化性能及MPC的凝结硬化性能的影响。相比现有技术,利用盐湖共存元素的助烧结作用可将氧化镁的烧结温度由1 500～1 800℃降低到1 200℃以下,有利于实现低活性氧化镁及MPC的低能耗、低成本绿色制备,促进MPC的推广应用。  相似文献   

大规模群桩基础水平承载力效应系数计算研究          下载免费PDF全文

贾鹏  王兰民  杨燕  刘上春 《地震工程学报》2020,42(5):1202-1207

桩基础在水平荷载或地震作用下的承载力计算一直是工程界的一个研究难点，近年来随着建筑、桥梁桩基础的规模大幅增加，基于小规模、小比例尺群桩基础水平承载力试验得出来的结论和计算方法可能会不适应新的计算要求，相关的认识和计算方法需要重新论证和更新。本文针对大规模群桩基础水平承载力效应系数的计算问题，首先对国内外研究进展进行调研，发现现有的规范计算方法可能会高估群桩基础的水平承载力。针对这些问题，对大规模群桩基础的水平承载力效应系数进行有限元数值计算分析，探讨水平承载力效应系数的规律，给出相应的计算方法，并与规范计算方法结果进行对比。本文的研究结果可为相应的工程设计问题提供依据，结果的适用性需要今后进一步的检验。  相似文献   

Damage assessment for submarine photoelectric composite cable under anchor impact     

《Applied Ocean Research》2018

The impact of dropped anchor on submarine photoelectric composite cables may possibly cause electrical faults, i.e. electricity and optical signal transmission failure. In order to study the impact capacity and structural impact failure mechanism, a test setup is designed originally to examine the structural and functional integrity. A detailed finite element model (FEM) is created, considering material nonlinearity and component interaction. A parametric analysis has been performed to predict the deformation of components and impact forces, under different impact velocities and collision directions. Relationships between the armor layer indentation rate and that of internal power and optical units are achieved. The impact deformation of internal entities can be evaluated intuitively by armor layer indentation. The proposed experimental and numerical methods are well correlated, suitable to assess the impact capacity of subsea power cables and assist the protection design of subsea power cables in engineering.  相似文献   

Developing constitutive models from EPR‐based self‐learning finite element analysis          下载免费PDF全文

Ali Nassr  Akbar Javadi  Asaad Faramarzi 《国际地质力学数值与分析法杂志》2018,42(3):401-417

A constitutive model that captures the material behavior under a wide range of loading conditions is essential for simulating complex boundary value problems. In recent years, some attempts have been made to develop constitutive models for finite element analysis using self‐learning simulation (SelfSim). Self‐learning simulation is an inverse analysis technique that extracts material behavior from some boundary measurements (eg, load and displacement). In the heart of the self‐learning framework is a neural network which is used to train and develop a constitutive model that represents the material behavior. It is generally known that neural networks suffer from a number of drawbacks. This paper utilizes evolutionary polynomial regression (EPR) in the framework of SelfSim within an automation process which is coded in Matlab environment. EPR is a hybrid data mining technique that uses a combination of a genetic algorithm and the least square method to search for mathematical equations to represent the behavior of a system. Two strategies of material modeling have been considered in the SelfSim‐based finite element analysis. These include a total stress‐strain strategy applied to analysis of a truss structure using synthetic measurement data and an incremental stress‐strain strategy applied to simulation of triaxial tests using experimental data. The results show that effective and accurate constitutive models can be developed from the proposed EPR‐based self‐learning finite element method. The EPR‐based self‐learning FEM can provide accurate predictions to engineering problems. The main advantages of using EPR over neural network are highlighted.  相似文献