首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 312 毫秒
1.
The variation of the backscatter strength with the angle of incidence is an intrinsic property of the seafloor, which can be used in methods for acoustic seafloor characterization. Although multibeam sonars acquire backscatter over a wide range of incidence angles, the angular information is normally neglected during standard backscatter processing and mosaicking. An approach called Angular Range Analysis has been developed to preserve the backscatter angular information, and use it for remote estimation of seafloor properties. Angular Range Analysis starts with the beam-by-beam time-series of acoustic backscatter provided by the multibeam sonar and then corrects the backscatter for seafloor slope, beam pattern, time varying and angle varying gains, and area of insonification. Subsequently a series of parameters are calculated from the stacking of consecutive time series over a spatial scale that approximates half of the swath width. Based on these calculated parameters and the inversion of an acoustic backscatter model, we estimate the acoustic impedance and the roughness of the insonified area on the seafloor. In the process of this inversion, the behavior of the model parameters is constrained by established inter-property relationships. The approach has been tested using a 300 kHz Simrad EM3000 multibeam sonar in Little Bay, NH. Impedance estimates are compared to in situ measurements of sound speed. The comparison shows a very good correlation, indicating the potential of this approach for robust seafloor characterization.  相似文献   

2.
Processing and analysis of Simrad multibeam sonar data   总被引：1，自引：0，他引：1  
The common approach to analysing data collected with multibeam and sidescan sonars is to visually interpret charts of contoured bathymetry and mosaics of seabed images. However, some of the information content is lost by processing the data into charts because this involves some averaging; the analysis might uncover more information if done on the data at an earlier stage in the processing. Motivated by this potential, I have created a software system which can be used to analyse data collected with Simrad EM1000 (shallow water) and EM12 (deep water) multibeam sonars, as well as to generate bathymetry contour charts and backscatter mosaics. The system includes data preprocessing, such as navigation filtering, depth filtering (removal of outlying values), and amplitude mapping using the multibeam bathymetry to correctly position image pixels across the swath. The data attributes that can be analysed include the orientation and slope of the seafloor, and the mean signal strength for each sounding. To determine bathymetry attributes such as slope, the soundings across a number of beams and across a series of pings are grouped and a least-squares plane fitted to them. Bathymetric curvature is obtained by detrending the grouped data using the least-squares plane and fitting a paraboloid to the residuals. The magnitudes and signs of the paraboloid's coefficients reveal depressions and hills and their orientations. Furthermore, the seafloor geology can be classified using a simple combination of these attributes. For example, flat-lying sediments can be classified where the backscatter, slope and curvature fall below specified values.  相似文献   

3.
济州岛南部海域海底声呐图像分析与声学底质分类   总被引：2，自引：2，他引：0  
东海北部外陆架靠近济州岛南部海域,是黄海槽向冲绳海槽延伸的部分,属于黑潮分支黄海暖流的通道入口,分布着脊槽相间的海底底形,对其海底声呐图像的处理分析及声学底质分类的分析研究,有助于了解该通道海底底形表层纹理特征及沉积物分布规律。基于在济州岛南部海域获取的多波束声呐数据,应用图像处理技术和方法,对数据进行了处理,获得了海底声呐影像图,并对其表层纹理特征进行了描述和分析;同时,基于多波束反向散射强度数据,结合19组海底地质取样数据,建立研究区海底反向散射强度与沉积物粒度特征之间的统计关系模型,并以改进的学习向量量化神经网络方法,实现对海底粉砂质砂、黏土质砂以及砂-粉砂-黏土3种底质类型的快速自动分类识别。  相似文献   

4.
This paper examines the potential for remote classification of seafloor terrains using a combination of quantitative acoustic backscatter measurements and high resolution bathymetry derived from two classes of sonar systems currently used by the marine research community: multibeam echo-sounders and bathymetric sidescans sonar systems. The high-resolution bathymetry is important, not only to determine the topography of the area surveyed, but to provide accurate bottom slope corrections needed to convert the arrival angles of the seafloor echoes received by the sonars into true angles of incidence. An angular dependence of seafloor acoustic backscatter can then be derived for each region surveyed, making it possible to construct maps of acoustic backscattering strength in geographic coordinates over the areas of interest. Such maps, when combined with the high-resolution bathymetric maps normally compiled from the data output by the above sonar systems, could be very effective tools to quantify bottom types on a regional basis, and to develop automatic seafloor classification routines.  相似文献   

5.
Using automated supervised segmentation of multibeam backscatter data to delineate seafloor substrates is a relatively novel technique. Low-frequency multibeam echosounders (MBES), such as the 12-kHz EM120, present particular difficulties since the signal can penetrate several metres into the seafloor, depending on substrate type. We present a case study illustrating how a non-targeted dataset may be used to derive information from multibeam backscatter data regarding distribution of substrate types. The results allow us to assess limitations associated with low frequency MBES where sub-bottom layering is present, and test the accuracy of automated supervised segmentation performed using SonarScope® software. This is done through comparison of predicted and observed substrate from backscatter facies-derived classes and substrate data, reinforced using quantitative statistical analysis based on a confusion matrix. We use sediment samples, video transects and sub-bottom profiles acquired on the Chatham Rise, east of New Zealand. Inferences on the substrate types are made using the Generic Seafloor Acoustic Backscatter (GSAB) model, and the extents of the backscatter classes are delineated by automated supervised segmentation. Correlating substrate data to backscatter classes revealed that backscatter amplitude may correspond to lithologies up to 4 m below the seafloor. Our results emphasise several issues related to substrate characterisation using backscatter classification, primarily because the GSAB model does not only relate to grain size and roughness properties of substrate, but also accounts for other parameters that influence backscatter. Better understanding these limitations allows us to derive first-order interpretations of sediment properties from automated supervised segmentation.  相似文献   

6.
Inhomogeneous substrate analysis using EM300 backscatter imagery   总被引：2，自引：0，他引：2  
Backscatter reflectivity from multibeam echo-sounders provides a powerful tool to efficiently characterize seafloor substrates. A comprehensive EM300 bathymetric and backscatter survey has been completed of Cook Strait, in central New Zealand. This paper presents a detailed analysis of the realtime corrections applied to the raw EM300 multibeam data and additional corrections required to compute angular variations of the backscatter strength. The corrections, including the local absorption coefficient, the influence of seafloor topography and sound refraction in the water column, are determined for different Cook Strait seafloor substrates. Modifying MB-System software code, we extracted the backscatter signal parameters in order to quantify the raw backscatter strength and apply additional processing. Profiles of backscatter strength versus incidence angle were computed for a variety of sites characterized by flat seafloor and homogeneous substrates, and for which ground-truth data were available. For each homogeneous site, different but characteristic backscatter profiles are observed that can be interpreted in terms of sediment facies. To analyze heterogeneous substrates, we present a statistical technique, based on a 3-dimensional distribution of (incidence angle, backscatter strength) couples that preserves geological information of the substrate components. This analysis, using backscatter data acquired on a submarine volcano, north of New Zealand, clearly differentiates soft sediments and lava flows within a heterogeneous substrate.  相似文献   

7.
The EM12 multibeam echosounder can record acoustic backscatter information as well as high resolution bathymetry. The dataset presented, from the axis of the Mid-Atlantic Ridge at 45° N, was the first EM12 survey of a mid-ocean ridge. This paper presents methods for utilising the backscatter information. Data processing enables the production of a mosaic of acoustic backscatter, and visualisation techniques are investigated to provide initial qualitative views of the combined backscatter and bathymetry datasets. The co-registration of the backscatter and bathymetry data enables quantitative analysis of their relationships. Various sites of different geological type have been selected and their angular acoustic backscattering relationships estimated, including the effect on backscatter of incidence angle, its regional variability with bottom type and the influence of bottom slope. Incidence angles and bottom type are shown to affect backscatter to a similar degree, while slopes appear to contribute little. The geometry of hull-mounted systems, such as the EM12, is significantly different from that of conventional sidescan sonars, such as GLORIA, and the backscatter images from the two types differ in various respects. Because of the wide variations in incidence angle that are common with hull-mounted systems, and the importance of incidence angle in determining backscatter strength, it is vital to consider the effect of incidence angle during interpretation.  相似文献   

8.
Obtaining absolute seafloor backscatter measurements from hydrographic multibeam echosounders is yet to be achieved. We propose a low-cost experiment to calibrate the various acquisition modes of a 30-kHz Kongsberg EM 302 multibeam echosounder in a range of water depths. We use a 38-kHz Simrad EK60 calibrated fisheries split-beam echosounder mounted at 45° angle on the vessel’s hull as a reference for the calibration. The processing to extract seafloor backscatter from the EK60 requires bottom detection, ray tracing and motion compensation to obtain acceptable geo-referenced backscatter measurements from this non-hydrographic system. Our experiment was run in Cook Strait, New Zealand, on well-known seafloor patches in shallow, mid, and deep-water depths. Despite acquisition issues due to weather, our results demonstrate the strong potential of such an approach to obtain system’s absolute calibration which is required for quantitative use of backscatter strength data.  相似文献   

9.
Both acoustic and sediment surveys were carried out in the Broughton Archipelago, British Columbia, in order to map a former aquaculture site and calibrate acoustic surveys with georeferenced sediment properties. The acoustic surveys included EM3000 Multibeam (including backscatter) and QTC VIEW™ (Series IV) technologies, while the geotechnical survey entailed Van Veen grab sampling of surface sediments and associated analyses. The two acoustic technologies were consistent in their ability to identify distinct regions of seafloor characterized by rock outcrops, consolidated substrates, or gel-mud depositional fields. Both multibeam backscatter data and QTC VIEW™ number-coded classifications were extracted across a range of circular areas located at each georeferenced sampling station (radii: 2, 3, 4, 5, 8, 12, 16, 20 m). Statistical correlations were observed between backscatter and certain geotechnical properties, such as sediment porosity, sediment grain size fractions (<2 μm, silt content), and particulate sulfur concentration. The areal resolution of backscatter extraction was explored in terms of determining a sensitive calibration technique between backscatter and sediment properties. In general the highest r2 values between backscatter and sediment variables were observed across extraction radii between 8 and 20 m. Such groundtruthing techniques could be used to interpolate seafloor characteristics between sampling stations and provide a steering tool for sampling designs associated with benthic monitoring programs.  相似文献   

10.
The sediment backscatter strength measured by multibeam echosounders is a key feature for seafloor mapping either qualitative (image mosaics) or quantitative (extraction of classifying features). An important phenomenon, often underestimated, is the dependence of the backscatter level on the azimuth angle imposed by the survey line directions: strong level differences at varying azimuth can be observed in case of organized roughness of the seabed, usually caused by tide currents over sandy sediments. This paper presents a number of experimental results obtained from shallow-water cruises using a 300-kHz multibeam echosounder and specially dedicated to the study of this azimuthal effect, with a specific configuration of the survey strategy involving a systematic coverage of reference areas following “compass rose” patterns. The results show for some areas a very strong dependence of the backscatter level, up to about 10-dB differences at intermediate oblique angles, although the presence of these ripples cannot be observed directly—neither from the bathymetry data nor from the sonar image, due to the insufficient resolution capability of the sonar. An elementary modeling of backscattering from rippled interfaces explains and comforts these observations. The consequences of this backscatter dependence upon survey azimuth on the current strategies of backscatter data acquisition and exploitation are discussed.  相似文献   

11.
Processing simultaneous bathymetry and backscatter data, multibeam echosounders (MBESs) show promising abilities for remote seafloor characterization. High-frequency MBESs provide a good horizontal resolution, making it possible to distinguish fine details at the water-seafloor interface. However, in order to accurately measure the seafloor influence on the backscattered energy, the recorded sonar data must first be processed and cleared of various artifacts generated by the sonar system itself. Such a preprocessing correction procedure along with the assessment of its validity limits is presented and applied to a 95-kHz MBES (Simrad EM 1000) data set. Beam pattern effects, uneven array sensitivities, and inaccurate normalization of the ensonified area are removed to make possible further quantitative analysis of the corrected backscatter images. Unlike low-frequency data where the average backscattered energy proves to be the only relevant feature for discriminating the nature of the seafloor, high-frequency MBES backscatter images exhibit visible texture patterns. This additional information involves different statistical distributions of the backscattered amplitudes obtained from various seafloor types. Non-Rayleigh statistics such as K-distributions are shown to fit correctly the skewed distributions of experimental high-frequency data. Apart from the effect of the seafloor micro-roughness, a statistical model makes clear a correlation between the amplitude statistical distributions and the signal incidence angle made available by MBES bathymetric abilities. Moreover, the model enhances the effect of the first derivative of the seafloor backscattering strength upon statistical distributions near the nadir and at high incidence angles. The whole correction and analysis process is finally applied to a Simrad EM 1000 data set.  相似文献   

12.
While the average seafloor backscatter strength within a narrow range of grazing angles can be used as a first-order classification tool, this technique often fails to distinguish seafloors of known differing geological character. In order to resolve such ambiguities, it is necessary to examine the variation in backscatter strength as a function of grazing angle. For this purpose, a series of multiply overlapping GLORIA sidescan sonar images (6.5 kHz) have been obtained in water depths ranging from 1000 to 2500 m. To constrain the placement of acoustic backscatter measurements and to measure the true impinging angle of the incident wave, the corresponding seafloor was simultaneously surveyed using the Seabeam multibeam system. As a result of the multiple overlap, the angular response of seafloor backscatter strength may be derived for regions much smaller than the swath width. By using the derived angular response of seafloor backscatter strength in regions for which sediment samples exist, an empirical seafloor classification scheme is proposed based on the shape, variance, and magnitude of the angular response. Because of the observed variability in the shape of the angular response with differing seafloor types, routine normalization of single-pass swath data to an equivalent single grazing angle image cannot be achieved. As a result, for the case of single-pass surveys, confident seafloor classification may only be possible for regions approaching the scale of the swath width  相似文献   

13.
Two highly active mud volcanoes located in 990–1,265 m water depths were mapped on the northern Egyptian continental slope during the BIONIL expedition of R/V Meteor in October 2006. High-resolution swath bathymetry and backscatter imagery were acquired with an autonomous underwater vehicle (AUV)-mounted multibeam echosounder, operating at a frequency of 200 kHz. Data allowed for the construction of ~1 m pixel bathymetry and backscatter maps. The newly produced maps provide details of the seabed morphology and texture, and insights into the formation of the two mud volcanoes. They also contain key indicators on the distribution of seepage and its tectonic control. The acquisition of high-resolution seafloor bathymetry and acoustic imagery maps with an AUV-mounted multibeam echosounder fills the gap in spatial scale between conventional multibeam data collected from a surface vessel and in situ video observations made from a manned submersible or a remotely operating vehicle.  相似文献   

14.
多波束反向散射强度数据处理研究   总被引：13，自引：5，他引：8  
在探讨多波束测深系统反向散射强度与海底底质类型的关系基础上,研究影响反向散射强度的各种因素,主要分析了海底地形起伏、中央波束区反射信号对反向散射强度的影响,并给出了消除这些影响的方法;将处理后的“纯”反向散射强度数据镶嵌生成海底声像图,为海底底质类型划分以及地貌解译提供了基础数据和辅助判读依据.  相似文献   

15.
A series of multibeam sonar surveys were conducted from 2009 to 2013 around Admiralty Bay, Shetland Islands, Antarctica. These surveys provided a detailed bathymetric model that helped understand and characterize the bottom geology of this remote area. Unfortunately, the acoustic backscatter records registered during these bathymetric surveys were heavily contaminated with noise and motion artifacts. These artifacts persisted in the backscatter records despite the fact that the proper acquisition geometry and the necessary offsets and delays were applied during the survey and in post-processing. These noisy backscatter records were very difficult to interpret and to correlate with gravity-core samples acquired in the same area. In order to address this issue, a directional notch-filter was applied to the backscatter waterfall in the along-track direction. The proposed filter provided better estimates for the backscatter strength of each sample by considerably reducing residual motion artifacts. The restoration of individual samples was possible since the waterfall frame of reference preserves the acquisition geometry. Then, a remote seafloor characterization procedure based on an acoustic model inversion was applied to the restored backscatter samples, generating remote estimates of acoustic impedance. These remote estimates were compared to Multi Sensor Core Logger measurements of acoustic impedance obtained from gravity core samples. The remote estimates and the Core Logger measurements of acoustic impedance were comparable when the shallow seafloor was homogeneous. The proposed waterfall notch-filtering approach can be applied to any sonar record, provided that we know the system ping-rate and sampling frequency.  相似文献   

16.
Over the past few years there have been remarkable and concomitant advances in sonar technology, positioning capabilities, and computer processing power that have revolutionized the mapping, imaging and exploration of the seafloor. Future developments must involve all aspects of the “seafloor mapping system,” including, sonars, ancillary sensors (motion sensors, positioning systems, and sound speed sensors), platforms upon which they are mounted, and the products that are produced. Current trends in sonar development involve the use of innovative new transducer materials and the application of sophisticated processing techniques including focusing algorithms that dynamically compensate for the curvature of the wavefront in the nearfield and thus allow narrower beam widths (higher lateral resolution) at close ranges . Future developments will involve “hybrid”, phase-comparison/beam-forming sonars, the development of broad-band “chirp” multibeam sonars, and perhaps synthetic aperture multibeam sonars. The inability to monitor the fine-scale spatial and temporal variability of the sound speed structure of the water column is often a limiting factor in the production of accurate maps of the seafloor; improvements in this area will involve continuous monitoring devices as well as improved ocean models and perhaps tomography. Remotely Operated Vehicles (ROV’s) and particularly Autonomous Underwater Vehicles (AUV’s) will become more important as platforms for seafloor mapping systems. There will also be great changes in the products produced from seafloor mapping and the processing necessary to create them. New processing algorithms are being developed that take advantage of the density of multibeam sonar data and use statistically robust techniques to “clean” massive data sets very rapidly. A range of approaches are being explored to use multibeam sonar bathymetry and imagery to extract quantitative information about seafloor properties, including those relevant to fisheries habitat. The density of these data also enable the use of interactive 3-D visualization and exploration tools specifically designed to facilitate the interpretation and analysis of very large, complex, multi-component spatial data sets. If properly georeferenced and treated, these complex data sets can be presented in a natural and intuitive manner that allows the simple integration and fusion of multiple components without compromise to the quantitative aspects of the data and opens up new worlds of interactive exploration to a multitude of users.  相似文献   

17.
This study applies three classification methods exploiting the angular dependence of acoustic seafloor backscatter along with high resolution sub-bottom profiling for seafloor sediment characterization in the Eckernförde Bay, Baltic Sea Germany. This area is well suited for acoustic backscatter studies due to its shallowness, its smooth bathymetry and the presence of a wide range of sediment types. Backscatter data were acquired using a Seabeam1180 (180 kHz) multibeam echosounder and sub-bottom profiler data were recorded using a SES-2000 parametric sonar transmitting 6 and 12 kHz. The high density of seafloor soundings allowed extracting backscatter layers for five beam angles over a large part of the surveyed area. A Bayesian probability method was employed for sediment classification based on the backscatter variability at a single incidence angle, whereas Maximum Likelihood Classification (MLC) and Principal Components Analysis (PCA) were applied to the multi-angle layers. The Bayesian approach was used for identifying the optimum number of acoustic classes because cluster validation is carried out prior to class assignment and class outputs are ordinal categorical values. The method is based on the principle that backscatter values from a single incidence angle express a normal distribution for a particular sediment type. The resulting Bayesian classes were well correlated to median grain sizes and the percentage of coarse material. The MLC method uses angular response information from five layers of training areas extracted from the Bayesian classification map. The subsequent PCA analysis is based on the transformation of these five layers into two principal components that comprise most of the data variability. These principal components were clustered in five classes after running an external cluster validation test. In general both methods MLC and PCA, separated the various sediment types effectively, showing good agreement (kappa >0.7) with the Bayesian approach which also correlates well with ground truth data (r2?>?0.7). In addition, sub-bottom data were used in conjunction with the Bayesian classification results to characterize acoustic classes with respect to their geological and stratigraphic interpretation. The joined interpretation of seafloor and sub-seafloor data sets proved to be an efficient approach for a better understanding of seafloor backscatter patchiness and to discriminate acoustically similar classes in different geological/bathymetric settings.  相似文献   

18.
A new highly precise source of data has recently become available using multibeam sonar systems in hydrography. Multibeam sonar systems can provide hydrographic quality depth data as well as high-resolution seafloor sonar images. We utilize the seafloor backscatter strength data of each beam from multibeam sonar and the automatic classification technology so that we can get the seafloor type identification maps. In this article, analyzing all kinds of error effects in backscatter strength, data are based on the relationship between backscatter strength and seafloor types. We emphasize particularly analyzing the influences of local bottom slope and near nadir reflection in backscatter strength data. We also give the correction algorithms and results of these two influent factors. After processing the raw backscatter strength data and correcting error effects, we can get processed backscatter strength data which reflect the features of seafloor types only. Applying the processed backscatter strength data and mosaicked seafloor sonar images, we engage in seafloor classification and geomorphy interpretation in future research.  相似文献   

19.
Processing Multibeam Backscatter Data   总被引：1，自引：0，他引：1  
A new highly precise source of data has recently become available using multibeam sonar systems in hydrography. Multibeam sonar systems can provide hydrographic quality depth data as well as high-resolution seafloor sonar images. We utilize the seafloor backscatter strength data of each beam from multibeam sonar and the automatic classification technology so that we can get the seafloor type identification maps. In this article, analyzing all kinds of error effects in backscatter strength, data are based on the relationship between backscatter strength and seafloor types. We emphasize particularly analyzing the influences of local bottom slope and near nadir reflection in backscatter strength data. We also give the correction algorithms and results of these two influent factors. After processing the raw backscatter strength data and correcting error effects, we can get processed backscatter strength data which reflect the features of seafloor types only. Applying the processed backscatter strength data and mosaicked seafloor sonar images, we engage in seafloor classification and geomorphy interpretation in future research.  相似文献   

20.
An assessment of the multibeam sonar data of the central Western Continental Margins of India has been carried out to evaluate the seafloor geomorphology and processes by examining the geomorphological attributes e.g., slope, sediments, structures, etc. associated with geomorphic features. The variation in relief and the features located in the region have been mapped and interpreted collectively by utilizing several geospatial mapping tools. The backscatter strength across the area, apparently congruent with the local relief, has helped to examine the sediment movement on the seafloor. The prominent features found in the region include faults, pockmarks, mounds, submarine terraces, and submerged fossil reefs. Several areas with varying topography engender comparable fractal dimension at short scale breaks, and the probability density functions (PDFs) utilizing backscatter data depicting overlapping classes. The present study highlights how fractals and scale break parameters can be utilized to determine the seafloor processes and associated sedimentological dynamics in a complex geographical environment with strong bottom currents, seasonal upwelling, and faulted structure. The role and impact of the various geomorphic processes on the reworking of sediment movement and the overall progression of the seafloor morphology has been revealed for the first time in this part of the ocean bottom.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号