共查询到20条相似文献，搜索用时 31 毫秒
1.
Soils are classified as sandy soils and clayey soils in most soil classification systems, and appropriate equations are used for practical design, depending on soil type, to represent each soil behavior. Sand-clay mixtures, however, need a special standard to evaluate their specific behaviors since they are categorized as intermediate soils or transitional soils and typically show intermediate properties. In this article, a series of cyclic triaxial tests were conducted on specific sand-fines mixtures with three fine types and various fine contents. The behaviors of various soil mixtures (silica sand with Iwakuni natural clay, Tottori silt, and Kaolin clay) were investigated by considering a concept of granular void ratio expressed in terms of sand structure. The cyclic shear strengths of the soil mixtures were also evaluated by increasing the fine content but no more than the threshold fine content. In the results, the cyclic deviator stress ratio decreased in dense soils whereas it increased in loose soils by increasing the fine content. In addition, a simple equation was proposed to predict the liquefaction resistance of sandy soils by evaluating the cyclic deviator stress ratio with a concept of equivalent granular void ratio. 相似文献
2.
A stress path with continuous rotation of the principal stress direction and continuous alteration of amplitude of deviatoric stress difference under the interaction of wave and earthquake loading was proposed based on the characteristics of the stress path under wave and earthquake loading, respectively. Using a GDS dynamic hollow cylinder apparatus, a series of cyclic triaxial-torsional coupling shear tests were performed on Nanjing saturated fine sand via the stress path mentioned previously under different relative densities, effective initial confining pressures, plastic fines contents, and loading frequencies to study the development of excess pore water pressure (EPWP) of saturated sand under the interaction of wave and earthquake loading. It was found that the development of EPWP follows the trend of fast-steady-mutative-drastic, which is different from that under the cyclic triaxial test or wave loading. The number of cycles causing initial liquefaction (NL) of saturated sand increases remarkably with relative densities. However, the relationships between NL and effective initial confining pressures, plastic fines content, or loading frequencies are more complex. 相似文献
3.
Khayra Merabet Ismail Benessalah Mohammed Chemmam 《Marine Georesources & Geotechnology》2020,38(4):461-467
AbstractThe study of the unsaturated soils is a very complex field to which several researches in laboratory and on site are directed these last years. An experimental study aims to quantify the influence of the Skempton coefficient B characterizing the degree of saturation on the behavior of the granular sand to the liquefaction resistance of sand. The study is based on undrained triaxial tests performed on natural Chlef sand carried out at an initial relative density Dr = 50% under a confining pressure of 50, 100 and 200?kPa for Skempton coefficient B?=?10 to 92%. The results of the tests show that an increase of confining pressure leads to an increase of the shear stress of the samples. For the lower value of the degree of saturation results of our findings indicate an increase of the resistance to liquefaction; our results are in good agreement with others observed in several research projects conducted with other sands. The increase of Skempton coefficient B induces an increase of pore water pressure and a decrease of the shear strength. The pore pressure (u) increases with an exponential manner with the increase of the degree of saturation; while the residual shear strength (Rs) decreases with logarithmic manner with the increase of degree of saturation (B). 相似文献
4.
The liquefaction resistance of the soils used to be estimated through the in situ tests, such as standard penetration test and cone penetration test; or by means of cyclic triaxial test in laboratory. However, both in situ tests and cyclic triaxial test are time-consuming and costly; this study introduces a quick and cost-effective method to evaluate the liquefaction resistance of soils under certain confining pressure in laboratory. A particular device modified from the conventional triaxial compression test apparatus, namely “Triaxial Cone Penetration Test”, was developed to obtain the peak values of cone resistance in soils so as to correlate the liquefaction resistance of the reclaimed soils evaluated by cyclic triaxial tests. The test result indicates a good correlation between the peak value of cone resistance and the corresponding cyclic stress ratio (CSR) at the state of initial liquefaction, in which the correlation for loose samples is better than that for dense samples. Besides, both peak values of cone resistance and corresponding CSR increase with fine content of soils reaches 10% and decreased with fine content varying between 10% and 50%. By examining the compositions of the soils with scanning electron microscopy and X-ray diffraction, it is found that the proportion and characteristics of the fines plays an important role on the liquefaction resistance of the reclaimed soils. 相似文献
5.
AbstractHollow cylinder torsional shear tests on loose isotropically and anisotropically consolidated calcareous sand were conducted to investigate the cyclic behavior under three different linear stress paths, including horizontal line, oblique line, and vertical line stress paths, in a coordinate system of the normal stress difference and the horizontal shear stress. The dominant strain components of the isotropically consolidated specimens are affected by the stress paths. With increasing consolidation stress ratio, axial strain gradually becomes the dominant strain component under the three different stress paths. The cyclic strength of the isotropically consolidated specimens under the three different stress paths are almost the same, while for the anisotropically consolidated specimens, the cyclic strengths are strongly affected by the stress paths. These results indicate that conventional cyclic triaxial tests may overestimate cyclic strength in some cases. Irrespective of the stress paths and cyclic stress ratios, the terminal residual excess pore pressure ratio decreases with increasing consolidation stress ratio. Moreover, an empirical equation is proposed to describe the relationship between the normalized shear work and the normalized residual excess pore pressure ratio. The comparative study reveals that the relationship proposed for silica sand is not suitable for the dynamic analyses of calcareous sand. 相似文献
6.
Noureddine Della Ahmed Arab Mostefa Belkhatir 《Marine Georesources & Geotechnology》2013,31(3):218-229
In order to study pore water response and static liquefaction characteristics of silty sand, which has previously experienced liquefaction, two series of monotonic triaxial tests were run on medium dense sand specimens (RD = 50%) at confining pressure of 100 kPa. In the first test series, the influence of the soil saturation under undrained static loading has been studied. It summarizes results of monotonic tests performed on Chlef sand at various values of the Skempton's pore pressure coefficient. Analysis of experimental results gives valuable insights on the effect of soil saturation on sand response to undrained monotonic paths. In the second series of tests, the overconsolidation influence on the resistance to the sands liquefaction has been realized on samples at various values of overconsolidation ratios (OCR). It was found that the increase of overconsolidation ratio (OCR) increases the resistance of sands to liquefaction. 相似文献
7.
AbstractIn this article, the dilatancy of calcareous soil is studied systematically based on triaxial consolidation drainage shear tests, and the difference in dilatancy between calcareous soil and siliceous soil is also investigated. It was found that: ① Calcareous soil experience obvious dilated deformation. Dilatancy tendency increases with increasing related density and decreases with increasing confining pressure. ② The volumetric strain rate initially increases from negative to positive. After it reaches a maximum, there is a small decrease in the volumetric strain rate, but it is still greater than zero, and the stress-strain curves are of softening type. ③ For the same condition, the dilatancy deformation of calcareous sand begins later than that of siliceous sand, and the volume compression before dilatancy is also larger for calcareous sand. ④ The critical state alone cannot accurately describe the entire deformation process of soil, and it is proposed that the phase transformation state be added to the standard method used to assess soil dilatation and contraction. ⑤ Based on the statistical analysis of experimental data, mathematical relationships were established between void ratio, relative density, and effective confining pressure of phase transformation state and critical state, respectively.
- Highlights
Reports results from a well-designed experiment that includes a good amount of samples and data.
Effects of relative density and effective confining pressure on deformation mode and mechanical properties of calcareous sand are evaluated.
The difference in dilatancy between calcareous sand and siliceous sand was compared
The phase-transformation state and critical state were compared with the axial strain, volumetric strain and deviatoric stress.
Using phase-transformation void ratio and critical void ratio to describe the whole deformation process of calcareous sand is proposed.
The mathematical expressions of phase-transformation void ratio and critical void ration were given, respectively.
8.
Stiffness degradation will occur due to the generation of accumulated pore pressure in saturated soft clays under cyclic loading. The soil static-dynamic multi-purpose triaxial and torsional shear apparatus in Dalian University of Technology was employed to perform different types of test on saturated soft marine clay in the Yangtze estuary. Undisturbed samples of the clay were subjected to undrained cyclic vertical and torsional coupling shear and cyclic torsional shear after three-directional anisotorpic consolidation with different initial consolidation parameters. Investigated were the effects of the initial orientation angle of the major principal stress, initial ratio of deviatoric stress, initial coefficient of intermediate principal stress and continuous rotation of principal stress axes on the stiffness degradation. It is found that the degradation index decreases (or degradation degree increases) significantly with increasing initial orientation angle of the major principal stress and initial ratio of deviatoric stress. Compared to the effects of the initial orientation angle of the major principal stress and initial ratio of deviatoric stress, the effect of initial coefficient of intermediate principal stress is less evident and this trend is more clearly reflected by the results of the cyclic torsional shear tests than those of the cyclic coupling shear tests. At the same cycle number, the degradation index obtained from the cyclic torsional shear test is higher than that from the cyclic coupling shear test. The main reason is that the continuous rotation in principal stress directions during cyclic coupling shear damages the original structure of the soil more than the cyclic torsional shear does. Based on a series of experiments, a mathematical model for stiffness degradation is proposed and the relevant parameters are determined. 相似文献
9.
作为一种常见的近海海底灾害地质现象,波致海床液化严重威胁着黄河三角洲地区海底工程设施的安全。粉质海床液化后,海底粉土的结构、物理和力学性质均发生了改变,研究该变化规律尤其是评估液化后海底粉土再次发生液化的可能性具有重要的理论意义和应用价值。本文利用室内动三轴仪对取自黄河三角洲已液化和未液化海底粉土开展了液化试验对比研究,讨论了已液化和未液化海底粉土在孔压增长模式和轴向动应变发展趋势方面的异同,对比分析了二者的液化势。研究结果表明:应变标准比孔压标准更适用于评估黄河三角洲地区海底粉土的液化势;孔压和动应变发展模式均表明与未液化粉土相比,已液化海底粉土再次发生液化的抗力有所提高;已液化和未液化海底粉土归一化孔压比ud/σ3与循环加载次数比N/Nf间相关关系可采用双曲线或指数函数模型进行定量化描述;未液化海底粉土的波致液化临界循环应力比约为0.20,已液化海底粉土的临界循环应力比约为0.35。研究成果有助于加深对海底粉土波致液化特性的认识,亦可为循环应力历史影响下的土体力学性质研究提供参考。 相似文献
10.
The foundations of nearshore and offshore structures are always subjected to long-term cyclic loading which is often a one-way, with low amplitude and a large number of cycles. Hence, the long-term dynamic behaviour of shoreline soils and sediments should be understood to avoid excessive deformation and liquefaction. As one of the most problematic soft soils in Melbourne, Coode Island Silt (CIS) at the northern shoreline of Port Phillip Bay contains a considerable but variable amount of sand. This paper explores the dynamic response of CIS containing different sand content subjected to a large number of cycles. To determine the liquefaction potential, and the effect of sand content on the resilient modulus and permanent strain of CIS, a series of long-term cyclic triaxial tests at a sinusoidal loading frequency of 1 Hz is performed. Based on the test results, it is found that CIS with varying sand content up to 30%, does not liquefy under the cyclic stress ratios and frequency applied in this study. Also, a sand content of 10% causes CIS to degrade more under cyclic loading. In the end, an empirical model to predict the permanent strain of CIS with a variable sand content is calibrated. 相似文献
11.
AbstractLiquefaction is a phenomenon developed in loose and saturated layers of sands subjected to dynamic or seismic loading, and often leads to excessive settlement and subsequent failures in structures. Several methods have been proposed to improve soil resistance against liquefaction, among which use of stone columns is one of the most applicable methods. In this research, the effect of stone columns with different geometries and arrangements on the liquefaction behaviour of loose and very loose saturated sands subjected to vibration is investigated using shaking table. Results of the experiments show that when using stone columns in sand layers, the level of maximum settlement is significantly reduced. Further, the presence of stone columns significantly reduces pore water pressure ratio. This further indicates that stone columns have a positive effect and reasonable performance, even in relatively strong earthquakes, provided that the number and cross-section of the columns are sufficient. In addition, stone columns reduce the pore water pressure dissipation time. Moreover, by increasing cross-sectional area and the number of columns, both pore water pressure and settlement decrease. Stone columns in loose sand have a greater effect on the reduction of pore water pressure compared to that of very loose sand. 相似文献
12.
Mohammed Chemmam Mostefa Belkhatir Rachid Bouferra 《Marine Georesources & Geotechnology》2016,34(4):384-394
This article presents a laboratory study of static behavior of silty-sand soils. The objective of this laboratory investigation is to study the effect of initial confining pressures and fines content on the undrained shear strength (known as liquefaction resistance) response, pore pressure, and hydraulic conductivity of sand–silt mixtures. The triaxial tests were conducted on reconstituted saturated silty-sand samples at initial relative density Dr = 15% with fines content ranging from 0 to 50%. All the samples were subjected to a range of initial confining pressures (50, 100, and 200 kPa). The obtained results indicate that the presence of low plastic fines in sand–silt mixture leads to a more compressible soil fabric, and consequently to a significant loss in the soil resistance to liquefaction. The evaluation of the data indicates that the undrained shear strength can be correlated to fines content (Fc), inter-granular void ratio (eg), and excess of pore pressure (Δu). The undrained shear strength decreases with the decrease of saturated hydraulic conductivity and the increase of fines content for all confining pressures under consideration. There is a relatively high degree of correlation between the peak shear strength (qpeak) and the logarithm of the saturated hydraulic conductivity (ksat) for all confining pressures. 相似文献
13.
利用水饱和法制备含天然气水合物试样,进行等向压缩试验和不排水三轴试验.采用天然气水合物临界状态(M HCS)模型同时预测排水条件和不排水条件下的三轴试验,并进行变动参数分析.不排水条件下,密实纯砂发生应变硬化,而相近密实度的含水合物试样出现应变软化,峰值偏应力随水合物饱和度和围压增大.通过与排水和不排水三轴试验结果的对... 相似文献
14.
ABSTRACTThe behavior of loose anisotropically consolidated calcareous sand obtained from an island in the South China Sea was investigated under undrained monotonic and cyclic loading in a hollow cylinder torsional apparatus. The tests were conducted on specimens which consolidated under various initial effective confining pressures and consolidation stress ratios. The monotonic test results show that the failure and phase transformation line are essentially independent of the consolidation conditions, while the initial contractive tendency of the specimens decreases with an increasing consolidation stress ratio. During monotonic loading of the anisotropically consolidated specimens, a same major principal stress direction is observed at the constant stress ratio lines up to the phase transformation line, irrespective of initial effective confining pressure. The cyclic strength of the sand increases with an increasing consolidation stress ratio. Moreover, a pronounced stress dependence is observed in the sand with higher consolidation stress ratio. During cyclic loading, the generated excess pore water pressure presents considerable fluctuations. The normalized terminal excess pore water pressure is described as a function of consolidation stress ratio. The tests show that the particle shape, rather than particle crushing, plays an important role in the monotonic and cyclic behaviors of the calcareous sand. 相似文献
15.
The post-cyclic behavior of biogenic carbonate sand was evaluated using cyclic triaxial testing through a stress control method under different confining pressures between 50 to 600 kPa. The testing program included a series of isotropically and anisotropically consolidated, undrained triaxial compression and extension tests on samples of remolded calcareous Bushehr sand. Grading analyses (before and after each test) were used to examine the influence of particle breakage on post-cyclic behavior of Bushehr sand. The particle breakage commonly occurred in these soils even in lower values of confining pressure, yet there was not a clear correlation between the post-cyclic responses and particle breakage. Based on the present study, a concept is suggested for post-cyclic behavior of carbonate sand. It was observed that post-cyclic strength has a good correlation with cyclic stress ratio, type of consolidation, and value of residual cyclic strain. For all specimens, it is clear that the post-cyclic strength is greater than monotonic strength, irrespective of confining pressure and relative density. 相似文献
16.
Chunxia Huang Zhilong Sui Lei Wang Kaifu Liu 《Marine Georesources & Geotechnology》2016,34(3):244-251
The risk of liquefaction and associated ground deformation may be reduced by using various ground-improvement methods, including the stone column technique. To examine the effects of stone columns, a shaking table experimental study using four models (two containing saturated sand and two containing stone column composite foundations) was conducted to measure the development and dissipation of excess pore water pressure and the acceleration response during a simulated earthquake. The test results demonstrate that the effectiveness of stone columns for mitigation of soil liquefaction during an earthquake depends on the following three aspects: (1) the densification of the surrounding soils; (2) drainage along the stone column; and (3) reduction in the total cyclic shear stress of the soil (because the cyclic shear stress is partially shared by the stone column). The first factor (the densification of the surrounding soils) is the most prominent factor among these three. The drainage and re-distribution of the shear stress can only develop fully for sand ground with a considerably higher density; thus, the effectiveness of the last two factors are only significant for dense sand ground. 相似文献
17.
18.
Ali Ghorbani Reyhaneh Jahanpour Hadi Hasanzadehshooiili 《Marine Georesources & Geotechnology》2020,38(1):1-22
AbstractAn elastoplastic, dynamic, finite-difference method was applied to study the effects of nonlinear seismic soil–pile interaction on the liquefaction potential of marine sand with piles. The developed model was well validated using the centrifuge test. The results showed that acceleration, bending moment, and excess pore water pressure complied well with centrifuge test results. The effect of different affecting parameters on liquefaction potential was investigated using parametric study. Using a sensitivity analysis, the pile embedment parameter was shown to be the most influential parameter. Finally, applying the evolutionary polynomial regression technique, a new model for predicting the liquefaction potential was presented. 相似文献
19.
海床式静力触探设备工作效率高,能够实现从垂向上对地层的连续探测,数据分辨率较好。通过对黄河口海域3个静力触探孔和1个地质钻孔的分析,将研究区20m以浅地层自上而下划分为粉土、粉质黏土、粉土夹粉砂或粉砂、粉质黏土、粉土五层,静力触探曲线对粉土层中的硬壳层和粉质黏土层中的贝壳夹层等特殊地质现象有很好的反映。对粉质黏土的静力触探参数与物理力学参数进行相关性分析,得到适合该区域的回归方程。采用基于CPT数据的液化判别法,对研究区表层粉土液化可能性进行评判,通过Seed简化法计算的周期应力比(CSR)与Olsen法计算的周期阻力比(CRR)的大小比较,得出当抗震设防烈度为7度时,研究区表层粉土不会液化,当抗震设防烈度为8度时,粉土层将发生液化,计算最大液化深度3.7m。 相似文献
20.
Yuke Wang Heyang Jia Hongjian Cai Xiangyuan Zhang 《Marine Georesources & Geotechnology》2013,31(3):402-407
ABSTRACTOne-way cyclic loading is more typical for traffic loading and cyclic triaxial test has been recognized as a useful method for solving many engineering problems. Under traffic loading, the influence of variable confining pressure on cyclic behavior of natural organic clay subjected to cyclic traffic loading is rarely reported in the literature. In this study, a laboratory investigation on undrained cyclic behavior of natural organic clay is presented and conducted by cyclic triaxial apparatus. Tests are conducted by both constant confining pressure and variable confining pressure, to simulate the loading conditions induced by passing vehicles in actual engineering. Different stress levels are also considered in this study. By comparing between the results of constant confining pressure tests and variable confining pressure tests, it shows that the one-way cyclic behavior of organic clay is influenced significantly by variation of confining pressure, in terms of pore water pressure, permanent axial strain and stress–strain hysteretic loops. 相似文献