共查询到20条相似文献，搜索用时 734 毫秒
1.
In this study, loss with time of dredged sea sand in a tidal embankment subject to sea level variation was examined through the centrifugal model test. The experimental results demonstrate that a differential subsidence occurs on the surface of the dredged-sea-sand fill and that the largest subsidence was observed just above the damaged portion of the geosynthetic mat. In addition, image analysis provided the largest displacement vector at the damaged portion of the geosynthetic mat, the shear-strain localization from the damaged portion of the geosynthetic mat through the center of the slope surface, and the crest of the dredge-sea sand fill. These displacement vectors and shear strains occurred early in the experiment and increased over time. Therefore, the loss of dredged sea sand can occur rapidly with damage to the geosynthetic mat and can possibly induce differential subsidence and cracks at the surface of the dredged-sea sand fill. 相似文献
2.
Mostefa Belkhatir Ahmed Arab Noureddine Della Tom Schanz 《Marine Georesources & Geotechnology》2013,31(2):106-122
The hydraulic conductivity plays a major role on the excess pore pressure generation during monotonic and cyclic loading of granular soils with fines. This paper aims to determine how much the hydraulic conductivity and pore pressure response of the sand-silt mixtures are affected by the percentage of fines and void ratio of the soil. The results of flexible wall permeameter and undrained monotonic triaxial tests performed on samples reconstituted from Chlef River sand with 0, 10, 20, 30, 40, and 50% nonplastic silt at an effective confining stress of 100 kPa and two relative densities (Dr = 20, and 91%) are presented and discussed. It was found that the pore pressure increases linearly with the increase of the fines content and logarithmically with the increase of the intergranular void ratio. The results obtained from this study reveal that the saturated hydraulic conductivity (k) of the sand mixed with 50% low plastic fines can be, on average, four orders of magnitude smaller than that of the clean sand. The results show also that the hydraulic conductivity decreases hyperbolically with the increase of the fines content and the intergranular void ratio. 相似文献
3.
Jun Chen Zhen-Yu Yin Ye-Shuang Xu Suksun Horpibulsuk 《Marine Georesources & Geotechnology》2016,34(5):420-430
This article presents a case history of determination of effective depth of prefabricated vertical drains (PVDs) under embankment loading on a very soft clay deposit in central China, near Jiujiang, Jiangxi Province. The height of the embankment was 5.3 m and construction time was about one year. The PVDs were installed to a depth of 8.5 m at a spacing of 1.5 m in a triangular pattern. Field observations and the finite element method (FEM) were employed to analyze the performance of the soft deposit during embankment construction. The influential depth of the embankment loading was evaluated based on settlement, excess pore pressure, and stress increase in subsoil, both from the observed data and FEM analysis. The effective PVD depth was determined in the following ways: (1) the depth of 5% subsoil settlement of surface settlement; (2) vertical stress increase in subsoil of 25% in-situ stress; and (3) consolidation time/PVD depth relation by FEM. Based on the analysis, the effective depth of PVDs was determined to be between 10 and 12.8 m for this field case. 相似文献
4.
—Presented is the numerical analysis of settlements of soft soil by a 2-D dynamic effective stressFEM method.The model based on the results of cyclic triaxial tests on the reconstituted soft Ariake clay isused to predict the wave induced excess pore water pressure and residual strain of soft clay.The settle-ments of two types of breakwaters on the soft clay under ocean wave load,a low embankment subjected totraffic load and the tunnel surrounded by soft clay in Shanghai subjected to locomotive load are calculatedas examples. 相似文献
5.
Consolidation occurs in estuarine marine clays for coastal reclamation by dissipation of the excess pore pressure, which is induced by increasing the total overburden stress during conventional mechanical surcharging. The excess pore pressure can be decreased usually by the use of several construction methods such as sand drain and paper drain. Besides the drain methods, vacuum can also be used in the soil mass to consolidate the estuarine marine clays by decreasing the pore pressure as well as increasing the effective stress.The study on vacuum consolidation is devoted so far mainly for laboratory model tests or numerical analysis in Korea. Recently, an instrumentation system was applied to manage the vacuum-applied consolidation on a field, in which a sewage disposal plant was constructed. While vacuum was applied, the behaviors of estuarine marine clays such as the settlement, lateral deformation and pore water pressure have been investigated precisely. The behavior of estuarine marine clays during vacuum-applied consolidation shows some difference from the behavior of estuarine marine clays in the case of conventional preloading. A principal difference is that the lateral deformation corresponding to settlement is smaller than before vacuum application even though the surcharge height has been increased. 相似文献
6.
Extreme waves can induce seepage in a seabed and cause problems to marine structures in coastal regions. In this study, the seepage under cnoidal waves was studied using the transient seepage equation. An analytical solution is presented for the pore pressure in a seabed of defined thickness. Parametric studies were carried out to examine the influence of air content in the pore water, and of the soil hydraulic conductivity on the seepage. It has been shown that the air content and the soil hydraulic conductivity can affect the pore pressure response significantly. An increase in the air content or a decrease in the soil hydraulic conductivity will increase the magnitude of the pore pressure gradient and results in the pore pressure varying sharply. The liquefaction potential of a seabed under cnoidal waves is discussed. Consequently, comparative studies are carried out to show that the soil shear modulus and Poisson constant can influence the difference between the transient seepage equation and Biot's equation, and the transient seepage equation is a limit of Biot's equation. 相似文献
7.
以 Iversion的海底稳定渗流理论为基础 ,运用静力极限平衡方法和库仑破坏准则 ,提出了以海底水下斜坡坡度、沉积物有效内摩擦角和内聚力为自变量 ,波浪在海底产生的孔压梯度为参变量的海底稳定性分析方法。并给出了黄河水下三角洲不同土质所需的临界孔压梯度判断曲线 ,预测了黄河水下三角洲的海底稳定性 ,其分析结果与实测资料吻合良好 相似文献
8.
A series of regular wave experiments have been done in a large-scale wave flume to investigate the wave-induced pore pressure around the submarine shallowly embedded pipelines.The model pipelines are buried in three kinds of soils,including gravel,sand and silt with different burial depth.The input waves change with height and period.The results show that the amplitudes of wave-induced pore pressure increase as the wave period increase,and decay from the surface to the bottom of seabed.Higher pore pressures are recorded at the pipeline top and the lower pore pressures at the bottom,especially in the sand seabed.The normalized pressure around pipeline decreases as the relative water depth,burial depth or scattering parameters increase.For the silt seabed,the wavelet transform has been successfully used to analyze the signals of wave-induced pore pressure,and the oscillatory and residual pore pressure can be extracted by wavelet analysis.Higher oscillatory pressures are recorded at the bottom and the lower pressures at the top of the pipeline.However,higher residual pressures are recorded at the top and the lower pressures at the bottom of the pipeline. 相似文献
9.
Bang-Fuh Chen 《Ocean Engineering》1999,26(1):47
A finite-differnece method was used to calculate the nonlinear hydrodynamic pressures acting on the coastal embankment faces by seismic-wave actions. The nonlinearity of free surface flow, convective acceleration, viscosity and surface tension of fluid are included in the analysis. The kinematic and dynamic free surface boundary conditions are employed for calculating the horizontal fluid velocity, pressure at the free surface and the surface profile of the fluid. The time-dependent water surface is transformed to the horizontal plane, and the flow field is mapped onto a rectangular, making it convenient to model the complex sea bottom geometry and the wavy water surface by the finite-difference method. Fully nonlinear and weakly nonlinear dynamic free surface conditions are used and compared. The effects of surface tension of fluid are also discussed. The nonslip boundary condition is applied on the most part of the interface between fluid and solid face, except the region near the intersection between free surface and wall face. The numerical results are presented for various water depths and ground motion intensities, and their associate viscous effects on coastal embankment hydrodynamics are discussed. 相似文献
10.
硅藻席沉积在热带西太平洋陆续被发现,其形成年代和机制对于热带西太平洋碳循环研究具有重要意义。本文对采自西马里亚纳弧,含近2.5 m厚硅藻席沉积的E20岩芯进行了高分辨率的XRF元素扫描、颜色扫描以及AMS14C测年分析。结果表明,E20可分为3个沉积单元,从下至上具有深海黏土—硅质软泥—硅质黏土的沉积序列,Ti、Fe、Cu、Br等元素呈三段式变化,Ca与Si元素呈反向变化。综合AMS14C测年结果推测,E20反映了西太平洋低纬度海区末次冰期以来显著的环境变化,10.9～28.6 ka B.P.为硅藻席勃发期,而末次冰期时风尘输入量的增加可能是勃发的主要原因。硅藻席沉积的保存与其周围的围陷地形有很大关系。 相似文献
11.
AbstractThe suction anchor becomes more popular for offshore oil and gas industry in deeper water. For suction anchor–soil interaction, the prediction of hydraulic conductivity of porous materials is a long-standing problem in offshore engineering. To investigate the hydraulic characteristics, an upward seepage flow through saturated sands is considered in this study. A numerical approach, which is able to describe the fluid–particle interaction at particle scale, has been employed to analyse fluid flow in sands. This approach is constructed by adopting a coupled discrete element method and computational fluid dynamic approach (CFD-DEM numerical model). The coupled CFD-DEM approach is first benchmarked by a classic geomechanics problem where analytical solutions are available, and then employed to investigate the characteristics of upward seepage flow in coarse sand columns. Through numerical modelling, the predicted relation between hydraulic gradient and flow velocity is obtained and it is compared with the classical analytical correlation. The effect of several bulk and micromechanical parameters including packing porosity, particle size combination and inter-particle rolling resistance on the flow characteristics is numerically examined. The results show that the particle polydispersity and packing porosity have significant effect on the hydraulic conductivity in the seepage flow. The introduction of inter-particle rolling resistance can change initial packing structure of particle assembly in some extent rather than the hydraulic conductivity from the particle shape effect perspective. A further development of numerical model, in which the effect of non-spherical particles on the seepage flow, will be carried out later. 相似文献
12.
A series of model tests were conducted on Perspex-made suction caissons in saturated dense marine sand to study the sand plug formation during extraction. Suction caissons were extracted by pullout loading or by pumping air into the suction caisson. Effects of the pullout rates, aspect ratios and loading ways (monotonic or sustained) on the pullout capacity, and plug formation were investigated. It was found that the ultimate pullout capacity of the suction caisson increases with increasing the pullout rate. The sand plug formation under the pullout loading is significantly influenced by the pullout rate and the loading way. When the suction caisson is extracted at a relatively slow rate, the general sand boiling through the sand plug along the inner caisson wall occurs. On the contrary, the local sand boiling will occur at the bottom of the suction caisson subjected to a rapid monotonic loading or a sustained loading. Test results of the suction caisson extracted by pumping air into the caisson show that the pressure in the suction caisson almost follows a linear relationship with the upward displacement. The maximum pressures for suction caissons with aspect ratios of 1.0 and 2.0 during extraction by pumping air into the caisson are 1.70 and 2.27 times the maximum suction required to penetrate the suction caisson into sand. It was found that the sand plug moves downward during extraction by pumping air into the caisson and the variation in the sand plug height is mainly caused by the outflow of the sand particles from the inside of the suction caisson to the outside. When the suction caisson model is extracted under the pullout rate of 2?mm/s (0.28?mm/s for the prototype), the hydraulic gradient along the suction caisson wall increases to the maximum value with increasing the penetration depth and then reduces to zero. On the contrary, when extracted under the pullout rate of 10?mm/s (1.4?mm/s for the prototype), the hydraulic gradient along the suction caisson wall increases with increasing the pullout displacement. When extracted by pumping air into the caisson, the hydraulic gradient reaches the critical value, and at the same time, the seepage failure occurs around the suction caisson tip. 相似文献
13.
14.
Present-day stress and pore pressure fields in the Cuu Long and Nam Con Son Basins, offshore Vietnam 总被引：1，自引：0，他引：1
Nguyen Thi Thanh Binh Tomochika Tokunaga Hoang Phuoc Son Mai Van Binh 《Marine and Petroleum Geology》2007,24(10):607-615
Knowledge of the in situ, or contemporary stress field is vital for planning optimum orientations of deviated and horizontal wells, reservoir characterization and a better understanding of geodynamic processes and their effects on basin evolution.This study provides the first documented analysis of in situ stress and pore pressure fields in the sedimentary formations of the Cuu Long and Nam Con Son Basins, offshore Vietnam, based on data from petroleum exploration and production wells.In the Cuu Long Basin, the maximum horizontal stress is mainly oriented in NNW–SSE to N–S in the northern part and central high. In the Nam Con Son Basin, the maximum horizontal stress is mainly oriented in NE–SW in the northern part and to N–S in the central part of the basin.The magnitude of the vertical stress has a gradient of approximately 22.2 MPa/km at 3500 m depth. Minimum horizontal stress magnitude is approximately 61% of the vertical stress magnitude in normally pressured sequences.The effect of pore pressure change on horizontal stress magnitudes was estimated from pore pressure and fracture tests data in depleted zone caused by fluid production, and an average pore pressure–stress coupling ratio (ΔSh/ΔPp) obtained was 0.66. The minimum horizontal stress magnitude approaches the vertical stress magnitude in overpressured zones of the Nam Con Son Basin, suggesting that an isotropic or strike-slip faulting stress regime may exist in the deeper overpressured sequences. 相似文献
15.
Vacuum preloading is often used to improve the geotechnical properties of dredged slurry. Although the performance of this method has improved with rapidly developing technology, soil columns usually formed on the drainage boundary induce the decrease of permeability around the boundary, thereby limiting the further development of this method. To address this issue, this paper proposes a method for pretreating the slurry combined with sand prior to vacuum consolidation. This method partially replaces the fine particles with sand to reduce the formation of soil columns. Two groups of vacuum preloading tests were performed to investigate the effect of sand content and sand grain size on the vacuum consolidation of dredged slurry. The test results revealed that for a given sand grain size, increasing the sand content of the sand–slurry mixture increased the pore water drainage and accelerated the dissipation of pore water pressure, thereby increasing the vane shear strength. In contrast, for a constant sand content, the samples containing coarse sand exhibited increased pore water drainage and accelerated dissipation of pore water pressure, thereby increasing the vane shear strength of the soil. 相似文献
16.
During the construction process of Qingdao Jiaozhou Bay Undersea Tunnel, the faults and other unfavorable geological discontinuities were often encountered. To study the water inrush mechanism in the faults, both physical model test and numerical analysis were carried out. The results of crown displacement and hydraulic pressure of the monitoring sections in the physical model and numerical model were analyzed in this paper. It was found that the displacement and hydraulic pressure in the process of tunnel construction are often interacted as both cause and effect, and the lower of hydraulic pressure is often accompanied with the growth of its displacement. The changing of the excavation disturbed zone during the excavation in the undersea tunnel was also studied. The results show that the excavation disturbed zone in fault is larger than that in surrounding rock mass, and the excavation disturbance effects in the filling type fault are both transient and persistent. When the displacement and hydraulic pressure in the undersea tunnel change sharply during excavation, there are relatively slow and continuous change trend of the displacement and hydraulic pressure. For practical purposes, to prevent water inrush in the undersea tunnel, more attentions should also be paid to the undersea tunnel after excavation. 相似文献
17.
海床土层在波浪的循环荷载作用下会逐渐累积孔压,降低土层的稳定性,并威胁海上工程。为了研究孔隙水压力的累积机制,本文提出离散元孔隙密度流方法,并改进研发离散元分析软件MatDEM,实现了海床沉积物孔压的累积过程模拟。基于现场试验装置及土体力学参数建立离散元模型,通过对比试验和数值模拟结果发现:对海床沉积物施加波浪荷载后,表层土体中产生较高孔压,并逐渐向深层传递;在循环波浪荷载作用下,土颗粒间孔压累积范围逐渐增加;当孔压累积时间足够长时,土层中孔压收敛于所施加最大荷载与最小荷载的平均值,此时若孔压达到初始有效应力,土体将发生液化,内部土颗粒成为再悬浮沉积物;在周期性波浪荷载作用下,土颗粒液化悬浮后发生移动,浅层颗粒位移量大,土体整体表现为圆弧形移动。 相似文献
18.
Zhuangcai Tian Lei Jia Naili Hu Susheng Wang Mingwei Zhang Guoqing Zhou 《海洋学报(英文版)》2023,42(2):142-149
Internal solitary wave(ISW) is often accompanied by huge energy transport, which will change the pore water pressure in the seabed. Based on the two-dimensional Biot consolidation theory, the excess pore water pressure in seabed was simulated, and the spatiotemporal distribution characteristics of excess pore water pressure was studied. As the parameters of both ISW and seabed can affect the excess pore water pressure, the distribution of pore water pressure showed both dissipation and phase lag... 相似文献
19.
破碎波对近海海岸地形以及海岸建筑物影响强烈,通过物理模型实验对孤立波、规则波作用下破碎带的床面形态以及孔隙水压力进行分析。破碎波冲击海床,破碎处床面上形成沙坝和沙坑,与规则波相比,孤立波破碎时对床面的冲刷更加剧烈,床面形成的沙坝和沙坑尺度更大,且土体内孔隙水压力幅值也较大。同时研究了波面变化对孔隙水压力的影响,发现波面变化历时曲线与孔隙水压力历时曲线相似,与孔隙水压力梯度历时曲线更为相似,说明波面变化更能反映海床内部孔隙水压力梯度的变化。通过探讨波浪与海床之间相互耦合作用,发现破碎带地形变化使得波浪出现不同破碎类型,分析得出卷破波比崩破波作用下孔隙水压力幅值大。 相似文献
20.
由常规枯竭型气藏改建的地下储气库仍然以气藏砂体(气砂体)为研究目标,与气藏砂体相邻的含水层(水砂体)亦能作为地下储气库的扩容空间,但这部分砂体很少被关注。板876地下储气库在储层精细描述基础上,结合气藏和气库的注采动、静态分析结果,评价了水砂体的分布范围和发育规模,利用精细地质模型计算了水砂体的总孔隙体积、未动用的及可动用的孔隙体积,应用板876地下储气库数值模拟技术对水砂体的扩容空间进行了验证,结果表明水砂体储集空间对地下储气库的扩容和运行效率具有现实意义。 相似文献