首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到18条相似文献,搜索用时 62 毫秒
1.
为研究敷设消浪材料不同构造浮箱的消浪性能,通过物模试验得到规则波作用下不同周期、不同波高、不同锚泊方式及不同结构形式下浮箱的透射系数(C_t)、反射系数(C_r)及波能衰减系数(C_s)。研究结果表明:随着相对堤宽(B/L)的增大,不同构造浮箱的透射系数均逐渐减小,反射系数逐渐增大,波能衰减系数逐渐增大;敷设消浪材料的浮堤相比于单浮箱透射系数减小了0.10左右,而采用方箱-垂直板式构造的浮堤消浪性能相对于单浮箱透射系数减小了0.10~0.15,且敷设消浪材料的浮堤结构在研究的2种波高下,相对堤宽达到0.30时,透射系数可减小到0.25;当浮堤采用张紧式锚泊时,其消浪性能相对于悬链式锚泊浮堤减小了0.10左右,通过对比不同构造浮箱的消浪性能,可为实际工程设计提供参考。  相似文献   

2.
在现有的矩形方箱和透空结构的基础上,提出一种由立管和水平板组合而成的消浪结构。利用波浪水槽物理模型试验,测试该结构在单向规则波作用下的消浪性能。分别探讨了其单排布置和双排布置时的透射系数随结构宽度、相对吃水深 度、相对间距等因素的变化规律。结果表明:单排布置时,透射系数随结构宽度的增大而减小,总体上随吃水深度的增大而减小;双排布置时,透射系数相对总宽度相同的单体结构减少 10 %,透射系数随吃水深度的增大而减小,前后间距对透射系数的影响不明显。对试验结果数据进行曲线拟合,得到了透射系数关于各影响因素的函数表达式。  相似文献   

3.
针对设计的新型双浮筒+Savinious型(S型)桨叶浮式防波堤的结构形式,基于势波理论和结构耦合水动力分析理论,利用面元积分和Newmark-β时间步进格式进行计算,研究其在线性规则波作用下的消波性能、运动响应和系泊张力响应,验证该结构的合理性。数值计算结果表明,阻尼修正后的防波堤纵摇运动响应合理,在波高H=1.5 m、波浪周期T=3 s下其消浪性能较为理想,透射系数达到0.65,同时系泊线张力呈周期响应并满足最大破断力的条件。此外,还研究了浮筒相对间距S1/L,浮筒—桨叶相对间距S2/L以及Savinious型桨叶高径比d/h三个无量纲关键几何参数对防波堤透射系数Ct和系泊线时域张力响应的影响。计算结果表明,浮筒间距S1越接近波长,防波堤消波性能越好,但迎浪侧张力响应幅值越大;随着浮筒—桨叶相对间距S2/L由0趋近于1,其透射系数随之减小,但迎浪侧张力响应幅值基本保持不变;减小桨叶的高径比d/h可以提高防波堤消波性能的稳定性,但张力响应幅值随之增大。  相似文献   

4.
为使防波堤同时具有良好的掩护效果和水体交换能力,提出了两种带有透浪通道的新型直立式防波堤。基于Fluent求解器建立了三维数值波浪水槽,通过与试验结果对比,验证了该数值水槽求解波浪与透空堤作用具有较高的精度。对两种防波堤在规则波作用下的透浪特性进行了研究,结果表明:透射系数K_t与透空率呈正线性相关,且可通过调整透浪通道间距,使相同透空率下K_t降低20%~30%。对同一结构,K_t随相对波长的增大而显著增大,但受相对波高的影响较小。在透空率大于0.16后,异型沉箱防波堤的消浪性能明显优于错位沉箱。基于数值计算结果,给出了以上两种透空堤波浪透射系数的经验公式。  相似文献   

5.
波浪作用下方箱-水平板浮式防波堤时域水动力分析   总被引:1,自引:0,他引:1  
在线性化势流理论范围内求解方箱-水平板浮式防波堤的波浪绕射和辐射问题,从时域角度分析了浮式防波堤的水动力特性.采用格林函数法将速度势定解问题的控制微分方程变换成边界上的积分方程进行数值求解,浮式防波堤的运动方程采用四阶Runge-Kutta方法求解.对不同层数水平板的浮式防波堤的波浪透射系数、运动响应和锚链受力进行了计算分析,结果表明方箱相对宽度对方箱-水平板浮式防波堤的波浪透射作用有重要的影响,透射系数随着方箱相对宽度的增加而减小.对于方箱加二层水平板的浮式防波堤,在本研究的计算条件下,当方箱相对宽度从0.110增加至0.295时,透射系数从0.88减小至0.30.水平板有利于增加浮式防波堤对波浪的衰减作用,但随着水平板层数从0增加至2,这种波浪衰减作用增加的程度趋弱.方箱-水平板的浮式防波堤的运动量小于单一方箱防波堤的运动量.与此对应,方箱-水平板防波堤的锚链受力小于单一方箱防波堤的锚链受力.  相似文献   

6.
弧板式透空堤消浪性能影响因素数值研究   总被引:1,自引:0,他引:1  
弧板式透空堤是由弧型板组成的新型防波堤结构。为探讨其透射系数的影响因素,利用Fluent软件基于N-S方程构建了波浪与板式透空堤相互作用的数值模型,讨论了相对潜深、入射波周期、相对波高、相对板宽和结构型式对透射系数的影响。结果表明:弧板式透空堤的透射系数随着相对波高和入射波周期的增大而增大,在静水面附近透射系数最小,尤以静水面和略高于静水面时的消浪效果最佳;在相同波浪要素条件下,静水面及其上0.02 m和0.04 m位置处,弧板式透空堤的消浪效果明显优于平板式透空堤。  相似文献   

7.
高桩挡板透空式防波堤消浪性能数值研究   总被引:1,自引:1,他引:0  
以RANS方程为控制方程,基于有限体积法,在动量方程中添加源项,建立了具有造波‐消波功能的数值波浪水槽。利用建立的源项造波数值波浪水槽,模拟了高桩挡板透空式防波堤在规则波作用下的消浪效果,完整地再现了堤前堤后的流态,分析了挡板相对入水深度对透浪系数的影响。在与试验值及拉帕公式对比后发现,数模计算结果与试验值较接近,拉帕公式偏大。研究了堤顶相对宽度、相对水深、相对波高对透浪系数的影响并提出修正公式,修正公式与计算值和试验值吻合较好。  相似文献   

8.
垂直挡板式透空堤作为一种新型的透空式防波堤结构,通过将挡浪板垂直设置于波能最集中的水体表层来消减波浪,透浪系数是其最关键的指标。通过物理模型试验,分析不规则波作用下入射波高、波周期、挡板相对入水深度、相对堤宽、相对挡板超高、相对面板超高等因素对垂直挡板式透空堤透浪系数的影响规律,并在Wiegel公式的基础上拟合了垂直挡板式透空堤透浪系数的计算公式。可作为今后类似透空式防波堤结构透浪系数的近似估算,具有一定的参考价值。  相似文献   

9.
针对海工作业平台、海洋养殖网箱等海洋装备的安全防护问题,提出了一种带空气透平的后弯管浮式防波堤,该空气透平既可将作用在防波堤上的波浪能转化成机械能并用于发电,还可显著减小防波堤的锚链力。在介绍了防波堤原理和结构特点的基础上,设计了物理实验模型,并在实验室造波池内进行了模型试验,研究了波浪周期、波高、吃水深度与弯管数量等因素对后弯管浮式防波堤透射系数和锚链力的影响规律。研究结果表明,波浪周期越短,波高越低,防波堤的透射系数越小,锚 链力越小,其消波性能优于传统的浮式防波堤.  相似文献   

10.
于珍  李雪艳  程志  孟钰婕 《海洋工程》2023,41(2):132-143
鉴于双弧板式透空堤的消浪性能仍不理想,提出了一种潜堤—双弧板组合结构,并基于OpenFOAM软件建立了波浪与该结构相互作用的数值模型,采用试验结果对所建数值模型进行验证。在此基础上,讨论了该新型结构的消浪特性、波压力分布特征以及所受波浪力的影响因素。结果表明,透射系数随相对板宽的增大而减小,反射系数则相反。透射与反射系数随相对潜深的变化较为显著。当结构位于静水位上方(即相对潜深为-0.05)时,透射系数最小而反射系数最大;当结构位于静水位下方(即相对潜深为0.05)时,透射系数最大而反射系数最小。该组合结构两块弧板上下表面的正负压力变化关于横轴近似对称,不同测点处的压力值差异显著。水平波浪力与垂直波浪力的变化趋势大致相似,但垂直波浪力远大于水平波浪力。研究结果可为其工程应用提供理论指导与技术支撑。  相似文献   

11.
浮式防波堤非线性波浪力实验研究   总被引:2,自引:1,他引:2  
对浮式防波堤在不同吃水深度、周期、波高和入射波波型情况,进行了波浪对浮式防波堤非线性作用力的研究,给出了有关实验结果。实验结果表明波浪力在周期较大时,随着波高的增加,出现一阶力减小、高阶力增大的强非线性现象。实验中出现了二阶力大于一阶力的现象,也出现了三阶力大于二阶力和一阶力的现象。  相似文献   

12.
- In this paper, the theoretical calculation of floating breakwater performance in regular waves with arbitrary wave direction is discussed. Under the hypothesis of linearized system and applying the strip theory, we can solve the boundary condition problems of diffraction potential and radiation potential. Introducing the asymptotic expression of the wave velocity potential at infinity and using wave energy conservation, we can separately calculate the transmitted waves generated by the sway, heave and roll motion of the floating breakwater and by the fixed breakwater. Finally, we define the amplitude ratio of the transmitted wave to the incident wave as the transmitted wave coefficient CT which describes the floating breakwater effectiveness. Two examples are given and the theoretical results obtained by the present method agree well with experimental results.  相似文献   

13.
采用遗传算法作为优化手段,以透射系数为目标函数,对给定横剖面面积的浮式防波结构物在规则波中的消波性能及剖面形状进行了最优化计算研究,探讨了透射系数最小的剖面形状与波浪周期之间的关系,为浮式防波结构物的设计提供了一定的理论依据  相似文献   

14.
An analytical method is developed to study the sheltering effects on arc-shaped floating perforated breakwaters. In the process of analysis, the floating breakwater is assumed to be rigid, thin, vertical, and immovable and located in water with constant depth. The fluid domain is divided into two regions by imaginary interface. The velocity potential in each region is expanded by eigenfunction in the context of linear theory. By satisfying continuity of pressure and normal velocity across the imaginary fluid interface, a set of linear algebraic equations can be obtained to determine the unknown coefficients for eigenfunction expansions. The accuracy of the present model was verified by a comparison with existing results for the case of arc-shaped floating breakwater. Numerical results, in the form of contour maps of the non-dimensional wave amplitude around the breakwater and diffracted wave amplitude at typical sections, are presented for a range of wave and breakwater parameters. Results show that the sheltering effects on the arc-shaped floating perforated breakwater are closely related to the incident wavelength, the draft and the porosity of the breakwater.  相似文献   

15.
This paper proposes ten types of improved floating breakwaters for experiment with regular waves, based on the experience in the development and manufacture of existing floating breakwaters both at home and abroad, and on the results of experimental studies on the hydraulic characteristics of several types of floating breakwaters. The wave heights before and behind the breakwaters are measured, the movements of floating breakwaters are observed and the chain forces of the floating breakwaters are measured. The paper studies and compares the hydraulic characteristics of the improved rectangular floating breakwaters of which the internal and external structures and their installation methods are changed. Finally the optimal type of structure is selected through experiments.  相似文献   

16.
The application of a Smoothed Particle Hydrodynamics (SPH) model to simulate the nonlinear interaction between waves and a moored floating breakwater is presented. The main aim is to predict and validate the response of the moored floating structure under the action of periodic waves. The Euler equations together with an artificial viscosity are used as the governing equations to describe the flow field. The motion of the moored floating body is described using the Newton’s second law of motion. The interactions between the waves and structures are modeled by setting a series of SPH particles on the boundary of the structure. The hydrodynamic forces acting on the floating body are evaluated by summing up the interacting forces on the boundary particles from the neighboring fluid particles. The water surface elevations, the movements of the floating body and the moored forces are all calculated and compared with the available experimental data. Good agreements are obtained for the dynamic response and hydrodynamic performance of the floating body. The numerical results of different immersion depths of the floating body are compared with that of the corresponding fixed body. The effects of the relative length and the density of the structure on the performance of the floating body are analyzed.  相似文献   

17.
A pile-restrained pontoon-plate floating breakwater is proposed in this paper.The laboratory physical-model tests are conducted to investigate the wave-dissipation property and heave-motion response of a model.The influence of the model′s geometric parameters including relative pontoon width,plate width,number of plates and pontoon draft on wave-dissipation performance and heave-motion response are discussed,as well as the correlation between these two factors.The result indicates that wave-dissipation performance of the proposed structure is better than the pontoon structure:its transmission coefficient and heave-motion height are reduced by 0.2 and 0.3,respectively,in comparison with those of the pile-restrained pontoon model at a relative pontoon width of 0.2.  相似文献   

18.
海上漂浮式光伏在北方冬季面临被海冰破坏的危险,冰期海洋环境对漂浮式光伏的影响尚处于研究初级阶段,因此非常有必要开展相关研究。为了有效防冰与抗冰,本文从水动力、波浪冲击性、支架稳定性、海水腐蚀、锚固方式等方面入手,首先对光伏方阵总环境载荷进行计算与仿真,然后对集装箱式漂浮防波堤、浮体方阵结构、支架、配件材料及锚固系统等进行优化设计,最后在潮汐变化显著的天津南港近海水域进行了冰期试验。试验数据与结果表明:浮式防波堤能有效阻挡围堰外海冰,消浪效果达到设计要求;塑料螺栓不仅可以有效避免因潮汐产生的浮体松动,而且能抵抗来自高盐高雾环境的腐蚀;设计的锚固系统能有效固定光伏方阵,使其漂移在可控范围内。该试验研究成果为优化北方冰期海上光伏技术方案提供了试验依据与理论支持。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号