共查询到20条相似文献，搜索用时 942 毫秒
1.
The paper presents a theoretical and an experimental investigation into the plastic collapse of circular steel corrugated cylinders under external hydrostatic pressure. The experimental investigation gives a detailed study of 9 steel corrugated cylinders which were tested to destruction. Six of these cylinders failed by plastic non-symmetric bifurcation buckling and three failed by plastic axisymmetric deformation. The results of these tests were used, together with the results obtained from previous tests, to present a design chart for the plastic collapse of these vessels. The design chart was obtained by a semi-empirical approach, where the thinness ratios of the vessels were plotted against their plastic knockdown factors. The process of using the design chart is to calculate the theoretical elastic instability pressure for a perfect vessel by the finite element method and also to calculate the thinness ratio for this vessel. Using the appropriate value of the thinness ratio, the plastic knockdown factors are obtained from the design chart. To obtain the actual collapse pressure of the vessel, the theoretical elastic instability pressure for a perfect vessel is divided by the plastic knockdown factor. This work is of importance in ocean engineering. A large safety factor must also be introduced. 相似文献
2.
The performance of multilayered thin steel plates subjected to close-range air blasts has been experimentally studied and compared with that of monolithic plates made of the same material and having equal mass. In present experiments, multilayered plates are in-contact four-layered thin steel plates and two types of deformation/failure modes were observed for them. Comparisons concerning deformation/failure modes, strain distributions and energy absorptions between the multilayered plate and its monolithic counterpart were conducted. It is found that the multilayered plate is much superior to its monolithic counterpart in the ability to deform against blast loading. Furthermore, under intense airblast loading, the multilayered plate can not only absorb much more energy but also effectively reduce the secondary destruction ability of structural fragments in comparison with its monolithic counterpart. 相似文献
3.
P.M. CiancioJ.A. Reyes 《Ocean Engineering》2003,30(11):1323-1333
This paper deals with the determination of the critical load in the buckling of isotropic, circular annular thin plates whose thickness varies slightly according to an exponential law.The outer edge of the plate is elastically restrained against rotation while the inner boundary is free. Classical small-deflection theory is used. An hidrostatic pressure acting in the middle plane is considered.The eigenvalues of the problem are obtained by means of an analytical approach based on the optimized Rayleigh-Ritz method. It is shοwnι that the results are in good agreement from an engineering viewpoint, with those available in the literature. 相似文献
4.
Murat Altekin 《Ocean Engineering》2010,37(11-12):1048-1060
Bending analysis of orthotropic super-elliptical plates of uniform thickness was investigated. Optimum location of the point supports was searched by minimizing the maximum absolute deflection. The support location which minimizes the bending moments at the supports was reported. The Ritz method was used and the total potential energy functional was modified by introducing the Lagrange multipliers to improve the accuracy of the stress resultants. The deflection and the bending moments computed at various points for a large variety of plate shapes ranging from an ellipse to a rectangle were checked with those of rectangular and elliptical plates. Good agreement was obtained for both cases. The structural response was found to be sensitive to support position. 相似文献
5.
变截面劲性水泥土桩承载特性室内模型试验研究 总被引：1，自引：0，他引：1
研究变截面劲性水泥土桩的几何特征对承载特性的影响,结果表明:具有1个扩大盘或2个扩大盘间距较大的变截面桩,盘下部的土体发生压缩和局部剪切破坏现象,上部的土体则发生梨形滑落;盘间距较小时,上下两盘之间的土体与两盘成为一体;变截面桩的桩侧荷载分担值均远大于桩端荷载分担值,盘的数量及间距对桩侧及桩端荷载分担值影响不大;1个盘时,其位置对承载力有一定的影响;2个等间距盘的变截面桩,盘位置越高承载力越高;盘间距对承载力影响不显著;3个盘的承载力大于2个盘的承载力,但结果相差不大;变截面桩的承载力得到显著提高,其承载力不小于与扩大盘直径相等的等截面桩;随着桩顶荷载的增大,盘承担的荷载增加显著,盘以下桩身的轴力因盘承担大部分而骤减,其降低幅度与盘的数量、位置及间距有关. 相似文献
6.
《中国海洋工程》2020,(4)
An investigation is conducted on the static ultimate limit state assessment of ship hull plates with elastically restrained edges subjected to axial compression. Both material and geometric non-linearities were considered in finite element(FE) analysis. The initial geometric imperfection of the plate was considered, while the residual stress introduced by welding was not considered. The ultimate strength of simply supported ship hull plates compared well with the existing empirical formula to validate the correctness of the applied boundary conditions, initial imperfection and mesh size. The extensive FE calculations on the ultimate strength of ship hull plates with elastically restrained edges are presented. Then a new simple empirical formula for plate ultimate strength is developed, which includes the effect of the rotational restraint stiffness, rotational restraint stiffness, and aspect ratios. By applying the new formula and FE method to ship hull plates in real ships, a good coincidence of the results between these two methods is obtained, which indicates that the new formula can accurately predict the ultimate strength of ship hull plates with elastically restrained edges. 相似文献
7.
船舶与海洋结构在服役期间会遭受电化学和微生物侵蚀等多种腐蚀环境影响,加筋板作为此类结构的主要受力构件,其表面易产生不规则形态的点蚀,引起构件的强度退化。利用ANSYS有限元软件构建加筋腹板遭受随机点蚀损伤的加筋板有限元模型,研究带板长宽比、带板长细比、加筋长细比和腐蚀体积损失率对加筋板极限强度的影响。研究结果表明,加筋遭受同等腐蚀体积损失率下,带板长宽比变化对极限强度退化的影响很小,但带板长细比和加筋长细比变化产生的影响明显;带板长细比越大,极限强度退化越严重,而加筋长细比越大,极限强度退化反而越小。针对文中研究的加筋板,当加筋长细比为 0.2时,腐蚀体积率为14%的随机点蚀导致结构极限强度退化程度达到约14.0%。因此,加筋的随机点蚀损伤会显著削弱加筋板结构的极限强度,其影响不可忽略。 相似文献
8.
Mohammed Y. Fattah Bushra S. Zbar Faris S. Mustafa 《Marine Georesources & Geotechnology》2017,35(8):1111-1120
In this study, the dynamic response of pile foundation in dry sandy soil excited by two opposite rotary machines was considered experimentally. A small scale physical model was manufactured to accomplish the experimental work in the laboratory. The physical model consists of two small motors supplied with eccentric mass (0.012?kg) and eccentric distance (20?mm) representing the two opposite rotary machines, an aluminum shaft as the pile, and a steel plate a pile cap. The experimental work was achieved taking the following parameters into considerations: pile embedment depth ratio (L/d, where L is the pile length and d is its diameter) and operating frequency of the rotary machines. All tests were conducted in medium dense fine sandy soil with 60% relative density. Twelve tests were performed to measure the change in load transferred through the pile’s tip to the underlying soil. To predict precisely the dynamic load that will be induced from the rotary machines, a mini load cell with a capacity of 100?kg was mounted between the aluminum plate (the machine base) and the steel plate (pile cap). The results revealed that, before machine operation, the pile tip load was approximately equal to the static load (machine and pile cap), whereas during machines’ operation, the pile tip load decreased for all embedment depth ratios and operating frequencies. This reduction was due to the action of skin friction that was mobilized along the pile during operation, and as a result the factor of safety against pile bearing failure increases. For all operating frequencies and pile lengths, the factor of safety against bearing failure increased during machines’ operation, where the pile tip load became less than its value before starting operation. During operation, the skin friction resistance mobilized along pile length led to decrease the bearing load. 相似文献
9.
- A generalized point conforming rectangular element for plate bending is proposed. The present element displacement field can not only satisfy the continuity of normal displacement and its derivative at the element node, but also satisfy the generalized continuity at the middle point of each element boundary, where the generalized conforming condition is to make the non-conforming residual to be minimum. Numerical results show that the proposed element is more accurate than the ordinary 4-node non-conforming rectangular plate element (ACM element). 相似文献
10.
钢管脐带缆包含多种螺旋缠绕的功能单元，其在外力载荷下会发生相对运动，而且钢管的刚度较大对扭转平衡有重要影响，因此，相对于普通电缆，钢管脐带缆在扭转平衡设计时更加困难。根据扭转平衡理论公式，采用控制变量法，以第二层铠装钢丝的绞合角度为变量进行扭转平衡设计。首先建立脐带缆缆芯有限元模型，对其施加拉伸载荷，结果显示缆芯出现了扭转，这证明不能将脐带缆缆芯视为一实心圆柱。其次建立不同绞合角度的脐带缆有限元模型，设置各功能单元的材料属性和摩擦系数，分析模型在拉伸载荷下的扭转角度，并将相同拉伸载荷下的扭转角度拟合为直线，从而得到钢管脐带缆在扭转平衡状态时的最优绞合角度。最后，采用试验方法对实物钢管脐带缆进行扭转平衡测试，测试结果显示在拉伸载荷下脐带缆单位长度扭转角度十分微小，这表明缆是扭转平衡的。因此验证了使用的有限元方法在钢管脐带缆扭转平衡设计中的有效性。 相似文献
11.
Corrugated stainless steel membranes have been used as the primary barriers for LNG carriers to reduce thermal stresses at cryogenic temperatures. As the capacity of the LNG cargo is increased, however, the corrugated stainless steel membranes suffer from buckling and collapse due to increased sloshing loads in large-capacity LNG cargo carriers. In this study, the pressure resistance of the corrugated part of the stainless steel membrane was evaluated using a finite element method for better design of the LNG containment system, and an experimental equipment was developed and the pressure resistance of the stainless steel corrugations was measured and compared with the calculated results. In addition, a new membrane with high-pressure resistance and its reinforcing method were developed and evaluated experimentally. 相似文献
12.
Jeom Kee Paik 《Ocean Engineering》2009,36(3-4):266-276
The main objective of the present paper is to numerically examine the residual ultimate strength characteristics of steel plates with longitudinal cracks under axial compressive actions. The present paper is a sequel to the author's previous paper [Paik, J.K., 2008. Residual ultimate strength of steel plates with longitudinal cracks under axial compression—Experiments. Ocean Engineering 35, 1775–1783]. In contrast to the previous paper, the present paper deals with nonlinear finite element method investigations. Because the test programme is usually limited to a few test models in number for many reasons, the application of nonlinear finite element methods is often more beneficial to handle a more variety of parameters of influence. In the present paper, the insights developed from a series of ANSYS nonlinear finite element method computations are documented, where the effects of the crack orientation, the crack location, the crack size, the plate thickness, and the plate aspect ratio on the residual ultimate strength of steel plates with longitudinal cracks under axial compression are discussed. The insights developed from the present work will be useful for cracking damage-tolerant design of steel-plated structures and also for health monitoring or condition assessment of aging steel-plated structures with cracking damages. 相似文献
13.
Uplift response of symmetrical anchor plates with and without grid fixed reinforced （GFR） reinforcement was evaluated in model tests and numerical simulations by Plaxis. Many variations of reinforcement layers were used to reinforce the sandy soil over symmetrical anchor plates. In the current research, different factors such as relative density of sand, embedment ratios, and various GFR parameters including size, number of layers, and the proximity of the layer to the symmetrical anchor plate were investigated in a scale model. The failure mechanism and the associated rupture surface were observed and evaluated. GFR, a tied up system made of fiber reinforcement polymer （FRP） strips and end balls, was connected to the geosynthetic material and anchored into the soil. Test results showed that using GFR reinforcement significantly improved the uplift capacity of anchor plates. It was found that the inclusion of one layer of GFR, which rested directly on the top of the anchor plate, was more effective in enhancing the anchor capacity itself than other methods. It was found that by including GFR the uplift response was improved by 29%. Multi layers of GFR proved more effective in enhancing the uplift capacity than a single GFR reinforcement. This is due to the additional anchorage provided by the GFR at each level of reinforcement. In general, the results show that the uplift capacity of symmetrical anchor plates in loose and dense sand can be significantly increased by the inclusion of GFR. It was also observed that the inclusion of GFR reduced the requirement for a large L/D ratio to achieve the required uplift capacity. The laboratory and numerical analysis results are found to be in agreement in terms of breakout factor and failure mechanism pattern. 相似文献
14.
岩石圈挠曲研究采用的是弹性薄板小挠度弯曲方程(即克希霍夫方程),克希霍夫方程基于薄板的前提,忽略并假设薄板内垂向应力为0。本文在无需垂向应力为0的这一与地质事实不相符的假设的情况下,由弹性体几何方程、物理方程和静力平衡方程推导出岩石圈挠曲-弹性薄板小挠度弯曲的新中面方程,具有同等的数学简洁性。取泊松比为0.25时,有DFF/D=1.125,即新挠曲方程中的挠曲刚度DFF要比经典的克希霍夫挠曲方程的D值大12.5%。本文推导的新方程不仅可以在岩石圈动力学,也可以在弹性力学中获得应用。 相似文献
15.
Three types of ice loading, which are most commonly present when ice acts on structures, are chosen and simulated for use of fatigue crack propagation tests on offshore structural steel A131. The three types of ice categorized in accordance with the failure modes when acting on structures called crushing ice, bending ice, and buckling ice, respectively. This paper presents an experimental investigation on the fatigue crack propagation behavior of widely used high strength steel A131 for offshore jackets in the loading environment of ice crushing, bending, and buckling. The test results of fatigue crack propagation in steel A131 under these simulated ice loading at temperature 292K. are presented and analyzed in detail in this paper. The amplitude root mean square stress intensity factor is optimized to be the fundamental parameter of fatigue crack propagation for all types of ice loading histories. The results are also compared with constant amplitude fatigue crack propagation conclusions as in wave loa 相似文献
16.
Materials have been developed that match densityp and dilatational sound speedc to the values of water as closely as possible while maintaining sufficient rigidity to serve for structural purposes. Matching of density and speed results in transparency for fluids only; the shear modulus in a solid admits the presence of a shear wave which causes deviation from idealpc behavior. The effect of a finite shear modulus on the reflection of plane waves by an infinite plane is analyzed. The shear modulus of the material was measured following a method developed by R. L. Adkins in 1966. Examples are given of the reflection coefficient as a function of incidence angle for values ofp andc close to those of the medium, and various ratios of plate thickness to dilatational wavelength. The condition of total reflection is shown to be related to the occurrence of thickness-shear resonances. Insertion-loss measurements on a structurally rigidpc panel are compared with results of the analysis. 相似文献
17.
主要探讨了半潜钻井平台浮体结构由于受到海洋环境腐蚀作用后的时变极限强度问题。首先,总结各种关于腐蚀损伤的平均厚度缩减模型,选择较能反映实际腐蚀过程的数学模型来估量浮体的钢板厚度缩减。在此基础上进行一系列极限强度计算,根据计算结果给出浮体极限强度预报公式。最后研究不同纵向构件板厚折减对极限强度的影响,发现浮体角隅板的单位体积影响率最高,而占结构比例大的构件厚度折减也将使得强度大大削弱,这两类纵向构件需要予以重点腐蚀保护。 相似文献
18.
The deployment of suitable configurations of mutually interacting floating bodies for efficiently controlling their hydrodynamic interactions towards the reduction of the wave drift forces and, thus, of the mooring lines’ loads, has, nowadays, gained a great scientific interest. In this paper, the hydrodynamic behaviour of a floating cylinder and a concentric annular flexible plate is analysed in the frequency domain aiming at the minimization of the drift forces acting on the cylinder by optimizing the flexural rigidity of the plate. The diffraction/radiation problem is solved using a higher-order boundary element method. The analysis is implemented assuming that both floating bodies oscillate freely in heave, while for the plate, flexible modes are, additionally, considered for describing its structural deformations. The required modes shapes are determined in vacuum (“dry” mode superposition approach) through analytical expressions. The flexural rigidity of the plate, D, is optimized at a specific wave number using a real-coded genetic algorithm. Initially, results are compared with numerical results of other investigators for the case of two rigid concentric floating cylinders. Next, extended results are presented, focusing on the effect of D, including its optimum value, on various physical quantities describing the behaviour of both the cylinder and the plate. Contrary to the isolated cylinder, the presence of the plate introduces sharp peaks in the variation pattern of the drift force of the cylinder, bounded at specific wave numbers, where resonance of the seiche mode of water motion in the annular cavity or of specific flexible modes of the plate occurs. However, by reducing D to its optimum value, the cylinder’s drift force obtains practically zero values at the target wave number, due to an efficient improvement of the wave field in the annular cavity around the cylinder. Moreover, a great reduction of the drift force compared to the isolated cylinder is achieved in the subsequent high frequency range. 相似文献
19.
Although Morison equation is often applied for simulating hydrodynamic force of marine structure, it may give poor results when non-linear behavior is severe or random wave is encountered. This leads to some modifications of Morison equation or other methods for predicting hydrodynamic force. One of them is the system identification technique. In this paper, NARMAX model theory is firstly used to identify the hydrodynamic system of heave damping plates, which are commonly installed on spar platform. Both linear and non-linear models are obtained. The comparisons between the predieted results and measured data indicate that NARMAX model can predict hydrodynamic force of a heave damping plate very well. The measured data for identification originate from forced oscillation tests, which are random records with given spectrum. The forced oscillation forms in experiment also contain simple harmonic, multi-frequency ones. 相似文献
20.
通过野外海区挂板的方法,探讨高密度聚乙烯(HDPE)、低密度聚乙烯(LDPE)、聚氯乙烯(PVC)、聚苯乙烯(PS)、聚对苯二甲酸乙二酯(PET)和聚氨酯(PUR)6种不同材料的塑料挂板对海月水母(Aurelia sp.1)附着的影响,分析不同塑料挂板表面粗糙度和海月水母附着的关系.研究结果表明:海月水母浮浪幼虫在夏末秋初可以附着在人工投放的塑料挂板附着基上,表明海岸带工程造成的人工附着基增多可能为海月水母的附着提供便利条件;海月水母螅状幼体在不同材料塑料挂板上的附着率有明显差异,PET、PUR和PVC塑料挂板海月水母螅状幼体附着率显著大于其他3种塑料挂板,其中PUR塑料挂板海月水母螅状幼体附着率最大,附着率为3.21±0.74 ind./cm2,HDPE塑料挂板海月水母螅状幼体附着率最低为0.26±0.08 ind./cm2;海月水母浮浪幼虫附着率与不同材料表面的粗糙度并不显著相关,表明塑料挂板材料的表面粗糙度并不是影响海月水母螅状幼体附着率的关键因子,而不同材料塑料挂板上形成的生物膜可能也对海月水母浮浪幼虫的附着产生影响.研究结果可为我国近岸海域有害水母海月水母暴发和防控研究提供一定的重要参考数据. 相似文献