共查询到20条相似文献，搜索用时 31 毫秒
1.
自主式深海海底溶质通量原位观测站研究进展 总被引：3，自引：1，他引：2
针对深入了解深海海底界面的物理、化学和生物动态变化过程及机制的观测需求,综述了自主式海底观测站(着陆器,lander)在深海海底溶质通量监测的研究进展。探讨了海底观测站的设计与实施技术,分析总结了深海自主式原位观测站在沉积物-水界面化学组分通量的观测机理,讨论了自主式海底观测站的国内外发展现状。自主式海底观测站具有可灵活机动选择观测地点、操作简单、便于多参数综合测量的特点,为获取深海海底长时空尺度综合参数资料提供了有效的技术支撑。根据目前深海生物地球化学循环研究特点,提出了自主式海底观测站面临的问题与发展建议。 相似文献
2.
泉州湾水体结构的潮周期变化 总被引：1，自引：0，他引：1
泉州湾6个站点的观测数据显示：内湾涨潮流历时由底层向表层逐渐变短，而落潮流历时则逐渐变长；同时，各个站点实测的盐度水深结构也具有明显的潮周期变化特征，这可能与局地水体的层化和混合机制的交替变化密切相关．进一步定量分析S2站位上影响水体结构变化的四种机制发现：外湾的河口环流作用与潮汐张力、风混合以及潮汐混合作用相比要小一个量级．在一般天气条件下的大潮周期，潮汐混合与潮汐张力相互竞争是导致水体结构交替变化的根本原因；小潮周期由于潮流混合作用减弱，水体层化现象得以持续较长时间，风的搅动在特定时刻可以起到削弱层化结构的作用． 相似文献
3.
This paper describes a complete set of methods for arranging acoustic images of the sea floor by projecting and interpolating data gathered with a novel front-scan sonar system, developed in the context of the EC-COSMOS project. Traditional sonar imaging systems for sea-floor analysis generate acoustic images during the motion of a ship; on the contrary, the front-scan sonar system not only provides information unreachable by traditional devices (blind region), but also does not need the ship motion to compose a whole image of the sea floor. Two different projection methods have been devised: a simpler analytical solution and a more precise ray-tracing approach. The development of an analytical solution is possible under the classical assumptions about a flat sea floor and a constant sound velocity profile; when these hypotheses are not realistic or a more precise image is required, a numerical solution obtained by a ray-tracing approach can be applied, which is based on some ad hoc solutions worked out for the front-scan sonar system. To move from the projection results to an image defined over a dense matrix of pixels, an interpolation stage is needed. To this end, an algorithm based on the generation of virtual-beam signals (only where necessary) has been tested and compared with more-traditional techniques. The potentials of the proposed projection and interpolation methods have been evaluated and some comparisons have been made, using real data gathered with the COSMOS sonar prototype during trials at sea. 相似文献
4.
TenCate J.A. Muir T.G. Caiti A. Kristensen A. Manning J.F. Shooter J.A. Koch R.A. Michelozzi E. 《Oceanic Engineering, IEEE Journal of》1995,20(4):300-310
The problem of locating very low frequency sound sources in shallow water is made difficult by the interaction of propagating acoustic waves with the sea floor. Slow wave speeds and the attendant short wavelengths suggest that low frequency beamforming and source localization with sea floor geophones can be accomplished with relatively small arrays when compared with hydrophone arrays in the water column. To test the feasibility of this approach, experiments were carried out in the shallow water of the Malta Channel of the Straits of Sicily where the Scholte wave speed was some 10 to 20 times slower that the speed of sound in water. A linear array of ten vertically gimballed geophones was deployed and measurements were made on propagating seismic wave fields generated by explosive shots. The resulting directivities, beam patterns, and sidelobe characteristics are in excellent agreement with array theory, which suggests that coherent processing is a viable technique on which to base new applications for seismic arrays on the sea floor. Supporting materials on the geophysics of Scholte waves and calculations of the wave field at the site are presented 相似文献
5.
An investigation of biological transport processes which may link the deep ocean floor to shallow depths was carried out at a site on the Madeira Abyssal Plain, depth 5440m, position 31°17′N 25°24′W. Benthic and midwater sampling was carried out concurrently; time lapse photography provided an estimate of biological activity on the bottom.Biomass was measured throughout the water column; overall biomass was low and no evidence was found for mass upward transport resulting from biological activity. The potential for transport via individual species does exist since a number of species were distributed from the sea bed to thousands of metres above the bottom. However, theres is no direct evidence for vertical migrations through these vast depth ranges and the numbers of individuals concerned is very small. The arrival and possible predation of a large food parcel on the deep sea floor was observed. 相似文献
6.
ＳｕｒｖｅｙｏｎｂｉｏｌｏｇｉｃａｌｆｏｕｌｉｎｇａｎｄｃｏｒｒｏｓｉｏｎｏｆｖｅｓｓｅｌｓＩＮＴＲＯＤＵＣＴＩＯＮＳｉｎｃｅｔｈｅｓｔｅｅｌｓｈｅｌｌｖｅｓｓｅｌｓｃａｍｅｉｎｔｏｂｅｉｎｇ，ｂｉｏｌｏｇｉｃａｌｆｏｕｌｉｎｇａｎｄｃｏｒｒｏｓｉｏ... 相似文献
7.
H.A. Karl W.C. Schwab A.St.C. Wright D.E. Drake J.L. Chin W.W. Danforth E. Ueber 《Ocean & Coastal Management》1994,22(3)
The oceans have been and will continue to be disposal sites for a wide variety of waste products. Often these wastes are not dumped at the designated sites or transport occurs during or after dumping, and, subsequent attempts to monitor the effects the waste products have on the environment are inadequate because the actual location of the waste is not known. Acoustic mapping of the seafloor with sidescan sonar is a very effective technique for locating and monitoring dredge-spoil material and other debris. Sidescan sonar provides an acoustic image or sonograph of the sea floor that is similar to a satellite image of the Earth's land surface. In effect sidescan sonar allows the water column to be stripped from the sea floor, thereby providing a clear, unobstructed view of the sea bed.An example of the potential of this technique is summarized herein for the Gulf of the Farallones region. More than 47 800 drums (55 gallon) and other containers of low-level radioactive waste were dumped on the continental margin offshore the San Francisco Bay between 1946 and 1970. These drums now litter a large area (1200 km2) of the sea floor within the Gulf of the Farallones National Marine Sanctuary (GFNMS). The exact location of the drums and the potential hazard the drums pose to the environment are unknown. To evaluate the risk, samples of the sediment, biota and water must be collected near and distant from the concentrations of barrels. To do this the exact location of the barrels must be known prior to sampling. The USGS, through a cooperative research agreement with GFNMS, used sidescan sonar to map two areas within the sanctuary. Total sea-floor coverage was obtained and computer-processed sonographic mosaics were constructed on board ship. Many small nongeologic targets were distributed throughout the survey areas that covered about 70 km2 on the shelf and 120 km2 on the slope. Analysis of the sidescan data suggests that the targets are 55-gallon drums. This interpretation was confirmed at one site with an underwater video and 35-mm camera system. Data were collected with both a 30-kHz and a 120-kHz sidescan system within a 15-km2 area on the shelf. We found that the barrels were more easily detected with the mid-range 30-kHz system than with the higher resolution 120-kHz system. Maps of barrel distribution derived from the sonographs are being used to design sampling schemes to evaluate the risk that the radioactivity may have on the biota and environment. 相似文献
8.
A novel variation of the geophysical technique known as MOSES, for Magnetometric Off-Shore Electrical Sounding, has been developed to map the electrical properties of the sea floor in Aretic regions. The particular target is the permafrost layer under the Beaufort Sea, a layer containing frozen or partially frozen sediment from 100 to 600 m thick underlying shallow sea water, typically 10 to 100 m deep, and several tens of metres of soft sediment. A detailed knowledge of the location and physical properties of the permafrost layer is essential for accurate interpretation of reflection seismic data. The permafrost can contain pockets, regions or layers of gas hydrate. The latter is both a possible resource and a hazard to drilling operations or hydrocarbon production. A local map of the permafrost zone is essential geotechnical information required prior to the construction of an offshore structure or pipeline.The MOSES method is particularly suitable for offshore electrical mapping as it can be made relatively insensitive to the shielding effects of the highly conductive sea water, in sharp contrast to many other electrical techniques. The transmitter is a vertical, long-wire bipole, extending from the sea surface to the sea floor. A commutated current is fed to two large electrodes: one near the sea surface and the other on the sea floor. The return current is through the sea water and the subjacent sediment. The receiver consists of two horizontal orthogonal coils located on the sea floor, and the data are measurements of two components of the magnetic field as a function of frequency and transmitter-receiver horizontal separation.The electrical conductivity of a sample of frozen material is much smaller than that of unfrozen or partially frozen sediment of the same type. Frozen and unfrozen thin layers are often observed sequentially throughout the geological section. The resistivity measured as a function of depth by an electrical logging tool is consequently highly variable. The resulting depth-averaged resistivity, the resistivity resolved by a surface electrical method, is macro-an-isotropic. An experimental design study reveals that both the vertical and horizontal averaged resistivities could be determined in a MOSES sounding without vertical scale distortion.A test of the methodology in very shallow water was conducted in the spring of 1986 at a site, approximate coordinates (70° N, 134.5° W), 85 km north-west of the town of Tuktoyaktuk. The instrumentation was lowered and subsequently recovered through holes in the ice which covers the Beaufort Sea at that time of the year. The transmitter power was obtained from a single lead-acid battery. Transmitter-receiver separations ranged from 10 to 300 m. A rapid increase in sediment resistivity with depth was observed. The higher resistivity values are consistent with those expected for a partially frozen zone. 相似文献
9.
Ben J. Korgen 《Marine Geophysical Researches》1971,1(3):354-357
A versatile probe for simultaneous studies of heat flow and near-bottom water parameters has evolved through modifications of the Bullard heat probe frame. Suitable sensor arrays have been used with this instrument to study (1) heat flow through the ocean floor, (2) water column temperature structure, (3) near-bottom current speeds, and (4) the differential cooling of water-column temperature sensors placed in a current speed gradient.Some of the advantages of such a modified Bullard probe are: (1) several parameters, including heat flow, can be measured across the sediment-water interface simultaneously, (2) the instrument frame is rigidly pinned to the ocean floor during measurement, permitting true Eulerian measurement in the water column with no effects of ship movement, swaying moorings or cable oscillation, and (3) the device is inexpensive and simple. 相似文献
10.
A case study: imaging OBS multiples of South China Sea 总被引：3，自引：0，他引：3
The subseafloor structure offshore South China Sea was imaged using first-order water-layer multiples from ocean-bottom seismometer
data and the results were compared to conventional imaging using primary reflections. The mirror-imaging method employs a
primaries-only reverse time pre-stack depth migration algorithm to image the receiver ghosts. The additional travel path of
the multiples through the water layer is accounted for by a simple manipulation of the velocity model and processing datum:
the receivers lie not on the sea floor but on a sea surface twice as high as the true water column. Migration results show
that the multiple-migrated image provides a much broader illumination of the subsurface than the conventional image using
the primaries, especially for the very shallow reflections. The resulting image from mirror imaging has illumination comparable
to the vertical incidence surface streamer (single-channel) reflection data. 相似文献
11.
Maintaining a fixed position near the sea floor is a critical capability during the deployment of remotely operated or intelligent (autonomous) undersea vehicles in a variety of missions, including inspection and repair of undersea structures, data collection, and surveillance. We present an automatic optical station-keeping system for application to submersible vehicles in deep waters by exploiting the information in sea floor images. Readily measurable spatio-temporal image gradients are used to detect and compute the vehicle's translational and yaw motions using a direct motion vision technique. The vision system has been implemented on a Windows-NT Pentium platform, and the estimated positions and yaw angles are communicated via a serial link to the control system, running on a PC-386. Accurate station-keeping is demonstrated in experiments with a three-thruster floating vehicle in a 6-ft×12-ft×6-ft water tank 相似文献
12.
S. Ramesh K. Nvv Murthy S. M. Hussain S. Ramasamy G. A. Ramadass 《Marine Georesources & Geotechnology》2020,38(1):57-63
AbstractPalar basin is located between Pennar and Cauvery sedimentary basins of East coast of India in Bay of Bengal, northeast Indian Ocean. Sea floor drill (Wire-line Autonomous Coring System – WACS) with operational capability of up to 3000?m water depth was developed to collect long cores from deep sea floor for geotechnical and ocean resource assessment studies. During the drilling operation it encountered Nummulitic coralline limestone of Lower Eocene age at 18 meters below the seafloor (mbsf) at 850?m water depth indicating carbonated platform presence for the first time at the study region. Bathymetry contour from Naval Hydrography Chart and General Bathymetric Chart of the Oceans (GEBCO) has revealed the presence of shallow mounds from 50 to 200?m depth closure contour near the sampling site at 850?m water depth which might be a submerged carbonated structure. Since, Nummulites are shallow water dwelling fauna (<20?m depth) but its occurrence at 18 mbsf in 850?m water depth is recorded because of the advancement in technology tool for long core sampling by means of sea floor drill. 相似文献
13.
14.
Precise Positioning of Ocean Bottom Seismometer by Using Acoustic Transponder and CTD 总被引：1，自引：0，他引：1
Shiobara Hajime Nakanishi Ayako Shimamura Hideki Mjelde Rolf Kanazawa Toshihiko Berg Eivind W. 《Marine Geophysical Researches》1997,19(3):199-209
We have obtained precise estimates of the position of Ocean Bottom Seismometers (OBS) on the sea bottom. Such estimates are usually uncertain due to their free falling deployment. This uncertainty is small enough, or is correctable, with OBS spacing of more than 10 km usually employed in crustal studies. But, for example, if the spacing is only 200 m for OBS reflection studies, estimates of the position with an accuracy of the order of 10 m or more is required.The determination was carried out with the slant range data, ship position data and a 1D acoustic velocity structure calculated from Conductivity–Temperature–Depth (CTD) data, if they are available. The slant range data were obtained by an acoustic transponder system designed for the sinker releasing of the OBS or travel time data of direct water wave arrivals by airgun shooting. The ship position data was obtained by a single GPS or DGPS. The method of calculation was similar to those used for earthquake hypocenter determination.The results indicate that the accuracy of determined OBS positions is enough for present OBS experiments, which becomes order of 1 m by using the DGPS and of less than 10 m by using the single GPS, if we measure the distance from several positions at the sea surface by using a transponder system which is not designed for the precise ranging. The geometry of calling positions is most important to determine the OBS position, even if we use the data with larger error, such as the direct water wave arrival data. The 1D acoustic velocity structure should be required for the correct depth of the OBS. Although it is rare that we use a CTD, even an empirical velocity structure works well. 相似文献
15.
Poul Andersen 《Ocean Engineering》1979,6(6):557-569
The influence of the sea bottom on ship motions and sea loads is examined. It is described how to calculate the vertical motions and loads for a ship with non-zero forward speed in regular waves by use of sttip theory and fluid finite element method. Results of such calculations are shown. The effects of shallow water are significant as is seen from several figures. 相似文献
17.
以载人深潜器的各种水动力参数和实际尺寸为基础,根据几何空间坐标方程建立了其运动学模型,采用MultiGen公司的Creator建模工具和Vega视景环境完成了在深海虚拟环境下的系统仿真。该系统可以实现深海机器人的可视化,更加直观、生动和实时的反映其位姿状态和水面、水下巡航过程。该系统实际应用在中国科学技术馆深海机器人展馆项目上,一方面展示载人深潜器的水下工作过程,同时也使得观众有机会亲身体验潜水器的操纵与驾驶。实际运行结果表明,该系统逼真地演示了载人深潜器水面备航、无动力下潜以及近海底巡航等仿真过程,能够满足系统仿真的实时性要求。该系统还可以应用到深海环境模拟研究、水下机器人运动仿真、控制系统调试以及操纵驾驶训练等中。 相似文献
18.
通过研究、分析现有基于遥感影像的舰船检测算法,提出了基于Itti视觉显著度模型改进的高分辨率遥感影像海面舰船检测方法,该方法利用海面舰船相对于海面背景信息视觉关注高的特点,参考视觉显著度模型计算原理,对高分辨率遥感影像中的颜色、亮度、方向、纹理等特征进行有效提取,然后利用归一化方法将不同特征融合,形成有利于舰船目标提取得视觉显著度图,最后对生成的视觉显著度图进行阈值分割和精细化处理获得最终的舰船检测结果。与传统舰船检测算法相比,本文算法能够有效检测复杂海面背景下的舰船目标,减少了单一特征变化对检测精度的影响,提高了检测准确率,具有较好的抗噪性和较强的鲁棒性。 相似文献
19.
The natural motion of a ship at sea produces undesirable effects on sonar displays. To overcome this problem some form of stabilization is desirable. A practical sonar display system, which uses image processing techniques to stabilize the displayed sonar image against rotational motion is described. The stabilization method provides the capability of image enhancement as well as improved image interpretation due to an increased area of view and a geometrically correct conversion to polar display. Details of the three processing stages required in the system are provided. These processes are ship motion analysis, image integration, and polar display conversion. Stabilized results are given for simulated ship motion 相似文献
20.
A wave-height meter using a simple microwave Doppler radar,simeq10 mW in power and 10.525 GHz in frequency, is proposed so that we can measure oceanic waves effectively while the ship is steaming. It was first applied to the measurement of the variation of water level generated in a wave tank, which suggested that it is adequately applicable to the measurement of oceanic waves. A field test was carried out off the cape of Nojimazaki by installing the Doppler radar 5 m above the sea level at the bow of the ship. The result agreed reasonably well with that measured simultaneously by the ultrasonic wave-height meter installed at the same position. Another test is running successfully on a larger ship with the wave-height meter installed at 9 m above the sea level. The significant wave height measured by the present meter is being compared with that observed visually by the navigation officers. 相似文献