共查询到20条相似文献，搜索用时 781 毫秒
1.
为研究孤立波作用下结构物周围流场特征,基于无网格SPH方法,建立孤立波与海洋结构物相互作用模型,对不同波幅孤立波作用下部分淹没矩形结构物周围波面、流速、涡量及结构受力特征进行计算分析,探索了相对波高对非淹没结构物周围流场的影响规律。结果表明:流场特征与相对波高密切相关,相对波高较小时,波面、流速、涡量及结构荷载均较为光滑,相对波高在0.2以上时,波峰爬升至结构物顶部并在越过结构物后与水槽内水体碰撞造成流场波动,波面、流速、涡量及结构荷载的波动幅度随着相对波高增大而增大,流场更加复杂,结构物水平和垂向负压也越大,且结构物周围涡分布逐渐向深度方向和下游方向发展。 相似文献
2.
张其一 《中国海洋大学学报(自然科学版)》2013,(4):100-105
海洋工程中结构物除了受到自身重力作用外,往往还受到海风、海浪、海流等的作用,使得海床土体中的基础一般受到集中力、弯矩和扭矩的联合作用,这一受力状态称为结构物基础的复合加载模式。本文以复合加载模式下海床土体变形规律与失稳机理为研究对象,基于通用有限元分析软件Abaqus,采用数值计算方法,对海床土体的极限承载能力进行了详细的研究。结果表明,荷载分量大小与组合形式对海床失稳机理与极限承载能力具有较大影响,H-M荷载空间内破坏包络面具有非对称性。本文给出的土体失稳模式,能够较为合理地评估复合加载模式下海床土体的变形规律;给出的土体极限力矩荷载判别准则,能够较为合理地计算海床土体的极限力矩荷载。 相似文献
3.
基于3D FEMDEM方法建立三维原型尺度数值模型,模拟波浪荷载作用下斜坡上护面块体内部的应力分布。波浪作用下结构物的水动力荷载采用微幅波理论模拟,护面块体之间的运动、碰撞接触以及块体内部的应力变化采用3D FEMDEM方法模拟。块体之间的接触力采用基于势函数的罚函数法计算,有限元的变形采用中心差分的显式方法求解。应用该数值模型与ANSYS软件程序对自重作用下混凝土扭王字块的内部应力分布特性进行了比较分析,验证了数值模型应力计算的可行性和计算精度。通过数值模拟计算给出了波浪作用下斜坡上护面块体之间的相对运动和块体内部的应力分布及应力历时曲线,探讨了块体内部应力变化特性。 相似文献
4.
水波数值模拟一直是水利、海岸、海洋工程和物理海洋等学科关注的重要研究领域之一。在诸多的水波模型之中,非静压水波模型以其计算精度和效率较为平衡的特点受到青睐。非静压水波模型经过近三十年的发展,为科学研究、工程设计分析和海洋资源开发等提供了重要的技术手段。然而,如何开发更为高效的非静压模型,拓宽模型的应用领域一直是研究的主要研究方向。文章综述了非静压模型概念的提出以及数值开发的难点,介绍了非静压模型在波浪传播演化和波浪与结构物相互作用这两方面的应用进展,将有助于研究者了解非静压水波模型的研究和应用现状。 相似文献
5.
6.
7.
本研究基于FVCOM环流模型,耦合ECMWF背景风场和Jelesnianski台风经验模型形成合成风场,对9711台风“温妮”过境辽河口区域的水动力进行模拟研究。模型通过在动量方程、湍流方程中加入附加源项来表达盐沼植被对水动力的阻碍作用。使用研究区域实测的潮位、流速、流向等数据对水动力模型进行验证,模拟结果与实测数据吻合较好。结果表明：潮滩盐沼植被对台风过境期间的潮位变化无明显影响,但对流速具有显著的衰减作用,且芦苇对潮流的衰减作用大于盐地碱蓬植被,芦苇区的速度最大衰减率达81.43%。此外,台风路径变化对辽河口湿地海域的增减水及流速影响较大,台风强度越强,局部区域造成的风暴潮增水和流速也相应越大。 相似文献
8.
近海区域广泛分布着第四纪新沉积的松散海洋土,波浪荷载作用下松散海床会发生液化进而对近海结构物的稳定性存在巨大威胁。本文采用中国科学院流体-结构-海床相互作用数值计算模型FSSI-CAS 2D,选用Pastor-Zienkiewicz-Mark Ⅲ（PZⅢ）弹塑性本构研究了波浪诱发的松散海床液化问题。分析了波浪荷载引起的松散海床内超孔隙水压力、有效应力以及应力角的时程变化特性,并预测了松散海床的渐进液化过程。计算结果表明,波浪荷载作用下松散海床内残余孔压会累积增长,海床表面最先发生液化,然后逐渐向下发展至液化最大深度。同时指出海床内超孔隙水压力的竖向分布特征和应力角的变化时程均可以作为判断海床液化的间接参数。最后,通过应力状态分析,讨论了海床渐进式液化的发展过程和趋势。 相似文献
9.
现行的海浪危险性评估方法仅以波高作为指标,没有考虑波浪周期对海上建筑物和船舶航行安全的影响。基于1979-2016年福建外海海浪数值后报结果,建立了基于周期的海浪强度和危险性等级划分标准,提出了基于波高和周期双指标的福建海域海浪危险性分析方法。结果表明,双指标下海浪危险等级分布结合了波高单指标下环状分布和周期单指标下带状分布的特点,以台湾海峡中南部海域海浪危险等级最高,闽南近岸海域海浪危险等级高于闽东和闽中海域,总体危险等级分布呈现南高北低的特征;双指标下的福建外海海浪危险等级分布比单指标考虑更为全面,不仅包含波高对结构物的影响还考虑了周期对浮式结构物和防波堤的作用,更加贴近真实情况下的海浪危险性特征。 相似文献
10.
漫堤是天文潮、风暴潮与海浪等物理要素作用于海堤后海水翻越海堤的物理过程。本文利用天文潮-风暴潮-台风浪耦合模式(ADCIRC+SWAN)、基于非结构三角形网格和高分辨率地理数据(海堤位置和高程、岸线和水深等)构建福建沿海精细化漫堤风险等级评估系统。该系统在近岸网格分辨率最高达50m,可精确刻画福建沿海复杂地形。利用模拟的水位与海浪参数,采用波浪爬高公式计算得到各海堤堤前波浪爬高。按照总水位与波浪爬高之和与海堤高程的对比,将漫堤风险分为五个等级。对2013年的超强台风天兔过程进行后报检验。结果显示,该系统计算的漫堤情况与灾后调查的漫堤实况基本一致,结果准确,说明本研究中采用的漫堤风险评估标准和方法是可行的。在此基础上,设计了4种不同的台风强度等级,对福建沿海206条海堤进行了漫堤风险等级评估,探究台风强度对漫堤风险的影响。结果表明:波浪爬高对漫堤风险的影响高于单纯的风暴潮增水;风暴潮增水随台风强度的增强增量较小,对于漫堤的风险影响较小;福建沿海波浪爬高普遍较高,随着台风强度的增强,波浪爬高会显著增加漫堤的风险等级,且应重视台风浪对海堤造成的冲击所导致的溃堤灾害。本研究可为沿海防灾减灾提供科学依据。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
13.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
14.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
15.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
16.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
Shigehisa Nakamura 《Marine Geodesy》2000,23(1):55-61
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone. 相似文献
19.
The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics. 相似文献
20.