共查询到20条相似文献，搜索用时 328 毫秒
1.
提出了一种既有钢筋混凝土框架结构的抗震加固方法,该法采用防屈曲支撑提高框架结构体系的水平承载力和耗能能力,利用外包钢进一步提高柱子的抗弯和抗剪承载力。采用开源有限元程序OpenSees,分别建立空钢筋混凝土框架和防屈曲支撑加固钢筋混凝土框架的分析模型,对2榀钢筋混凝土框架的抗震性能进行模拟。防屈曲支撑采用了弹塑性桁架单元模型,加固框架柱混凝土考虑了外包钢的约束作用。将分析结果与拟静力试验结果进行比较,以检验分析模型的准确性,以及研究防屈曲支撑和外包钢对混凝土框架抗震性能的影响。分析结果表明,数值模拟与试验结果吻合较好,验证了基于OpenSees建立的数值模型的准确性;外包钢有效改善了框架柱的抗弯承载力和变形能力;防屈曲支撑显著提高了加固框架体系的水平刚度、水平承载力和耗能能力。 相似文献
2.
Seismic retrofit of reinforced concrete frames using buckling‐restrained braces with bearing block load transfer mechanism 
下载免费PDF全文
下载免费PDF全文 Kuan‐Yu Pan An‐Chien Wu Keh‐Chyuan Tsai Chao‐Hsien Li Hsen‐Han Khoo 《地震工程与结构动力学》2016,45(14):2303-2326
A new method of retrofitting reinforced concrete (RC) frames with buckling‐restrained braces (BRBs) to improve frame strength, stiffness and energy dissipation is proposed. Instead of typical post‐installed anchors, load is transferred between the BRB and RC frame through compression bearing between an installed steel frame connected to the BRB, and high‐strength mortar blocks constructed at the four corners of the RC frame. This avoids complex on‐site anchor installation, and does not limit the allowable brace force by the anchor strength. Cyclic displacements of increasing amplitudes were imposed on two RC frame specimens retrofitted with different BRB strength capacities. In one of the frames, the bearing blocks were reinforced with wire mesh to mitigate cracking. A third RC frame was also tested as a benchmark to evaluate the retrofit strength and stiffness enhancements. Test results indicate that the proposed method efficiently transferred loads between the BRBs and RC frames, increasing the frame lateral strength while achieving good ductility and energy‐dissipating capacity. When the bearing block was reinforced with wire mesh, the maximum frame lateral strength and stiffness were more than 2.2 and 3.5 times the RC frame without the BRB respectively. The BRB imposes additional shear demands through the bearing blocks to both ends of the RC beam and column member discontinuity regions (D‐regions). The softened strut‐and‐tie model satisfactorily estimated the shear capacities of the D‐regions. A simplified calculation and a detailed PISA3D analysis were shown to effectively predict member demands to within 13.8% difference of the measured test results. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
3.
为研究钢筋砼摩擦耗能支撑框架结构的动力反应性能 ,对其中的摩擦耗能器单元和框架杆单元的单元刚度和力学模型做了分析。钢筋砼摩擦耗能支撑单元由支撑杆单元和钢板—橡胶摩擦耗能器单元组成 ,支撑单元可取空间杆单元 ,摩擦耗能器单元为平面应力矩形单元。摩擦耗能器单元的剪切恢复力曲线为理想的弹塑性曲线 ,根据耗能器单元的力学模型 ,可确定其在每一时刻的刚度 ;框架结构空间杆单元的恢复力模型采用双线型模型 ,根据杆单元的力学模型 ,可确定其在每一时刻的刚度。并利用所编制的程序对十层单榀两跨空间普通框架和摩擦耗能支撑框架在地震作用下进行了弹塑性反应时程分析 ,结果表明耗能支撑框架的顶层最大位移明显小于普通框架 相似文献
4.
Self-centering seismic retrofit scheme for reinforced concrete frame structures: SDOF system study 总被引：1，自引：1，他引：0
This paper presents the results of a parametric study of self-centering seismic retrofit schemes for reinforced concrete (RC) frame buildings. The self-centering retrofit system features flag-shaped hysteresis and minimal residual deformation. For comparison purpose,an alternate seismic retrofit scheme that uses a bilinear-hysteresis retrofit system such as buckling-restrained braces (BRB) is also considered in this paper. The parametric study was carried out in a single-degree-of-freedom (SDOF) system framework since a multi-story building structure may be idealized as an equivalent SDOF system and investigation of the performance of this equivalent SDOF system can provide insight into the seismic response of the multi-story building. A peak-oriented hysteresis model which can consider the strength and stiffness degradation is used to describe the hysteretic behavior of RC structures. The parametric study involves two key parameters -the strength ratio and elastic stiffness ratio between the seismic retrofit system and the original RC frame. An ensemble of 172 earthquake ground motion records scaled to the design basis earthquake in California with a probability of exceedance of 10% in 50 years was constructed for the simulation-based parametric study. The effectiveness of the two seismic retrofit schemes considered in this study is evaluated in terms of peak displacement ratio,peak acceleration ratio,energy dissipation demand ratio and residual displacement ratio between the SDOF systems with and without retrofit. It is found from this parametric study that RC structures retrofitted with the self-centering retrofit scheme (SCRS) can achieve a seismic performance level comparable to the bilinear-hysteresis retrofit scheme (BHRS) in terms of peak displacement and energy dissipation demand ratio while having negligible residual displacement after earthquake. 相似文献
5.
为检验抗侧刚度比和支撑布置方式等因素对具有不同总层数的屈曲约束支撑钢框架的抗震性能影响,借助SAP2000软件,探讨6层、12层、18层屈曲约束支撑钢框架结构在抗侧刚度比分别为1、2、3、4、5共五种工况及倒V型和单斜向两种支撑布置方式下的抗震性能。结果表明,屈曲约束支撑钢框架结构基底剪力-顶点位移曲线呈典型的双线性特征;随抗侧刚度比的增大,结构的层间位移角总体上呈降低趋势,基底剪力及支撑轴力增大,顶点水平位移变小,框架所分担的剪力降低;倒V型布置支撑较单斜向布置具有略大的基底剪力、谱加速度,较小的顶点位移、层位移、层间剪力和框架剪力分担率。分析表明,总体上来看,倒V型布置较单斜向布置时支撑框架结构具有略优的抗震性能;抗侧刚度比较支撑布置方式对支撑框架结构抗震性能的影响更为显著。 相似文献
6.
This study presents a nonlinear modelling technique for reinforced concrete (RC) frames retrofitted with metallic yielding devices to predict the seismic response using a computer software OpenSees. The numerical model considers the axial–flexure interaction, shear force–displacement response and the bond-slip characteristics of the frame members. The predicted hysteretic response has been compared with the results of slow-cyclic testing. The validated numerical model is then used to predict the seismic response of a five-story RC frame with soft-story. Nonlinear cyclic pushover and dynamic analyses are conducted to investigate the effectiveness of the proposed retrofitting scheme in enhancing the lateral strength and energy dissipation potential and in controlling the premature failure of the study frame. Analysis results showed significant improvement in the seismic response of RC frames with soft-story using the proposed retrofitting technique. 相似文献
7.
Performance evaluation of retrofitting strategies for non-seismically designed RC buildings using steel braces 总被引：1，自引：1，他引：0
H. Varum F. Teixeira-Dias P. Marques A. V. Pinto A. Q. Bhatti 《Bulletin of Earthquake Engineering》2013,11(4):1129-1156
Recent major earthquakes around the world have evidenced that research in earthquake engineering must be directed to the vulnerability assessment of existing constructions lacking appropriate seismic resisting characteristics. Their retrofit or replacement should be made in order to reduce vulnerability, and consequent risk, to currently accepted levels. In this work, the efficiency of ductile steel eccentrically-braced systems in the seismic retrofitting of existing reinforced concrete (RC) buildings is studied. The retrofit technique studied consists in a bracing system with an energy dissipation device, designed to dissipate energy by shear deformation. The numerical model was calibrated with cyclic test results on a full-scale structure. The models used for the RC frame and masonry represent their real behavior and influence in the global structural response. The steel bracing system was modeled with strut rigid elements. The model for the energy dissipater device reproduces rigorously the behavior of the shear-link observed in the cyclic tests, namely in terms of shear, drift and energy dissipation. With the calibrated numerical model, a series of non-linear dynamic analyses were performed, for different earthquake input motions, intending to study: the influence of the retrofitting system in the response of bare and infilled structures; the influence of the location and strength of the retrofitting system. 相似文献
8.
Masonry buildings are primarily constructed out of bricks and mortar which become discrete pieces and cannot sustain horizontal forces created by a strong earthquake.The collapse of masonry walls may cause significant human casualties and economic losses.To maintain their integrity,several methods have been developed to retrofit existing masonry buildings,such as the constructional RC frame which has been extensively used in China.In this study,a new method using precast steel reinforced concrete(PSRC)panels is developed.To demonstrate its effectiveness,numerical studies are conducted to investigate and compare the collapse behavior of a structure without retrofitting,retrofitted with a constructional RC frame,and retrofitted with external PSRC walls(PSRCW).Sophisticated finite element models(FEM)were developed and nonlinear time history analyses were carried out.The results show that the existing masonry building is severely damaged under occasional earthquakes,and totally collapsed under rare earthquakes.Both retrofitting techniques improve the seismic performance of existing masonry buildings.However,it is found that several occasional earthquakes caused collapse or partial collapse of the building retrofitted with the constructional RC frame,while the one retrofitted by the proposed PSRC wall system survives even under rare earthquakes.The effectiveness of the proposed retrofitting method on existing masonry buildings is thus fully demonstrated. 相似文献
9.
钢管混凝土叠合柱边框内藏钢桁架核心筒抗震性能试验研究 总被引：1，自引：1，他引：0
为进一步改善混凝土核心简的抗震性能,本文提出了钢管混凝土叠合柱边框内藏钢桁架组合核心筒.进行了2个1/6缩尺的核心筒模型在低周反复荷载下的抗震性能试验研究,1个为钢管混凝土叠合柱边框毛组合核心筒,1个为钢管混凝土叠合柱边框内藏钢桁架组合核心筒.通过试验,对比分析了2个核心简的承载力、延性、刚度及其衰减、滞回特性、耗能能力及破坏特征,给出了钢管混凝土叠合柱边框内藏钢桁架组合核心筒的承载力计算模型,计算结果与实测值符合较好.研究表明,钢管混凝土叠合柱边框内藏钢桁架组合核心筒与钢管混凝土叠合柱边框组合核心筒相比,其抗震性能明显提高. 相似文献
10.
This study describes the seismic performance of an existing five storey reinforced concrete building which represents the typical properties of low-rise non-ductile buildings in Turkey. The effectiveness of shear walls and the steel bracings in retrofitting the building was examined through nonlinear static and dynamic analyses. By using the nonlinear static analysis, retrofitted buildings seismic performances under lateral seismic load were compared with each other. Moreover, the performance points and response levels of the existing and retrofitting cases were determined by way of the capacity-spectrum method described in ATC-40 (1996). For the nonlinear dynamic analysis the records were selected torepresent wide ranges of duration and frequency content. Considering the change in the stiffness and the energy dissipation capacities, the performance of the existing and retrofitted buildings were evaluated in terms of story drifts and damage states. It was found that each earthquake record exhibited its own peculiarities, dictated by frequency content, duration, sequence of peaks and their amplitude. The seismic performance of retrofitted buildings resulted in lower displacements and higher energy dissipation capacity depending mainly on the properties of the ground motions and the retrofitting strategies. Moreover, severe structural damage (irreparable or collapse) was observed for the existing building. However, buildings with retrofit alternatives exhibited lower damage levels changing from no damage to irreparable damage states. 相似文献
11.
Esra Mete Güneyisi 《地震工程与结构动力学》2012,41(5):853-874
The present paper investigates the seismic reliability of the application of buckling restrained braces (BRBs) for seismic retrofitting of steel moment resisting framed buildings through fragility analysis. Samples of regular three‐storey and eight‐storey steel moment resisting frames were designed with lateral stiffness insufficient to comply with the code drift limitations imposed for steel moment resisting frame systems in earthquake‐prone regions. The frames were then retrofitted with concentrically chevron conventional braces and BRBs. To obtain robust estimators of the seismic reliability, a database including a wide range of natural earthquake ground motion records with markedly different characteristics was used in the fragility analysis. Nonlinear time history analyses were utilized to analyze the structures subjected to these earthquake records. The improvement of seismic reliability achieved through the use of conventional braces and BRBs was evaluated by comparing the fragility curves of the three‐storey and eight‐storey model frames before and after retrofits, considering the probabilities of four distinct damage states. Moreover, the feasibility of mitigating the seismic response of moment resisting steel structures by using conventional braces and BRBs was determined through seismic risk analysis. The results obtained indicate that both conventional braces and especially BRBs improve significantly the seismic behavior of the original building by increasing the median values of the structural fragility curves and reducing the probabilities of exceedance of each damage state. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
12.
13.
Seismic performance of steel reinforced ultra high-strength concrete composite frame joints 总被引：1，自引：1，他引：0
To investigate the seismic performance of a composite frame comprised of steel reinforced ultra high-strength concrete (SRUHSC)
columns and steel reinforced concrete (SRC) beams, six interior frame joint specimens were designed and tested under low cyclically
lateral load. The effects of the axial load ratio and volumetric stirrup ratio were studied on the characteristics of the
frame joint performance including crack pattern, failure mode, ductility, energy dissipation capacity, strength degradation
and rigidity degradation. It was found that all joint specimens behaved in a ductile manner with flexural-shear failure in
the joint core region while plastic hinges appeared at the beam ends. The ductility and energy absorption capacity of joints
increased as the axial load ratio decreased and the volumetric stirrup ratio increased. The displacement ductility coefficient
and equivalent damping coefficient of the joints fell between the corresponding coefficients of the steel reinforced concrete
(SRC) frame joint and RC frame joint. The axial load ratio and volumetric stirrup ratio have less influence on the strength
degradation and more influence on the stiffness degradation. The stiffness of the joint degrades more significantly for a
low volumetric stirrup ratio and high axial load ratio. The characteristics obtained from the SRUHSC composite frame joint
specimens with better seismic performance may be a useful reference in future engineering applications. 相似文献
14.
针对平面不规则RC框架结构,从构件安全层次出发提出基于传力路径的减震设计方法。首先根据广义结构刚度法的基本原理计算结构中所有构件的重要性系数,再假定消能支撑的截面参数,取每层最重要的构件位置布置支撑,经支撑在最不利地震组合下的轴力验算后确定支撑的最终设计参数和数量,然后考虑远场、近场有脉冲以及近场无脉冲地震动从双向输入对结构响应的影响,对减震前、后结构分别进行动力时程分析。分析结果表明,利用此方法优化布置支撑能为结构中重要构件提供有效保护,且在小、中、大震下消能支撑均能运作良好,使整体结构响应得到很好地控制。 相似文献
15.
首先介绍了CFRP加固受损钢筋混凝土柱的数值模拟方法,通过OpenSees软件进行了建模分析,数值模拟结果与试验结果的对比验证了该数值模型的有效性;其次,对一6层钢筋混凝土框架以受极罕遇地震影响进行预损,采用损伤指数和折减系数的方法建立震损钢筋混凝土框架的分析模型,并选择5种不同的CFRP加固方案对其进行加固;最后,对CFRP加固的震损RC框架进行增量动力分析。定量的评价了CFRP加固震损RC框架的抗整体性倒塌能力和抗倒塌安全储备。结果表明:CFRP加固能有效提高震损钢筋混凝土框架结构的抗震性能。加固部位的选择对加固效果的影响很大,在所选用的5种CFRP加固方案中,对底层及第2层的梁柱进行加固的方案对提高震损钢筋混凝土框架的抗整体性倒塌能力效果最佳。 相似文献
16.
为研究加固后锈蚀箍筋约束混凝土柱的抗震性能,设计16个钢筋混凝土矩形柱,对加速锈蚀后的试件采用外包钢及CFRP、GFRP材料进行加固处理,随后开展低周往复荷载试验,以研究不同加固材料、不同加固包裹方式、不同黏结材料等因素对锈蚀箍筋约束混凝土柱滞回曲线、骨架曲线、刚度衰减、延性性能及耗能能力等抗震性能指标的影响。研究结果表明:(1)与未锈蚀柱相比,加固后的箍筋锈蚀柱以弯剪破坏为主,CFRP加固试件较GFRP加固试件具有更高的承载力,但破坏时延性不如GFRP加固试件;(2)外包钢加固试件、CFRP加固试件、GFRP加固试件的耗能能力较未锈蚀试件分别增大222.3%、123.9%、98.5%,延性系数也相应增大45.3%、22.3%、25.6%。总之,外包钢加固对箍筋锈蚀柱抗震性能的提升最大,CFRP加固次之,但优于GFRP加固;整包加固优于环包加固;环氧树脂胶黏结略优于水泥基灌浆料黏结。 相似文献
17.
对两个1/6缩尺的开洞核心筒结构模型进行了偏心水平荷载作用下的低周反复荷载试验研究,其中包括一个普通开洞混凝土核心筒和一个内藏钢桁架开洞混凝土组合核心筒。在试验的基础上,对比分析了两个试件的承载力、刚度、延性、滞回特性、耗能能力、破坏特征以及抗震机理。试验研究表明,在偏心水平荷载作用下,内藏钢桁架开洞混凝土组合核心筒比普通开洞混凝土核心筒抗震能力显著提高。 相似文献
18.
19.
The results of experimental tests carried out on reinforced concrete (RC) full‐scale 2‐storey 2‐bays framed buildings are presented. The unretrofitted frame was designed for gravity loads only and without seismic details; such frame was assumed as a benchmark system in this study. A similar RC frame was retrofitted with buckling‐restrained braces (BRBs). The earthquake structural performance of both prototypes was investigated experimentally using displacement‐controlled pushover static and cyclic lateral loads. Modal response properties of the prototypes were also determined before and after the occurrence of structural damage. The results of the dynamic response analyses were utilized to assess the existing design rules for the estimation of the elastic and inelastic period of vibrations. Similarly, the values of equivalent damping were compared with code‐base relationships. It was found that the existing formulations need major revisions when they are used to predict the structural response of as‐built RC framed buildings. The equivalent damping ratio ξeq was augmented by more than 50% when the BRBs was employed as bracing system. For the retrofitted frame, the overstrength Ω and the ductility µ are 1.6 and 4.1, respectively; the estimated R‐factor is 6.5. The use of BRBs is thus a viable means to enhance efficiently the lateral stiffness and strength, the energy absorption and dissipation capacity of the existing RC substandard frame buildings. The foundation systems and the existing members of the superstructure are generally not overstressed as the seismic demand imposed on them can be controlled by the axial stiffness and the yielding force of the BRBs. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
20.
M. Fakharifar M. K. Sharbatdar Z. Lin A. Dalvand A. Sivandi-Pour G. Chen 《地震工程与工程振动(英文版)》2014,13(1):59-73
This paper presents a new FRP retrofi tting scheme to strengthen local beam-column joints in reinforced concrete(RC) frames.The new retrofi tting scheme was proposed following a preliminary study of four different existing retrofi tting schemes.A numerical simulation was conducted to evaluate the effectiveness of FRP-strengthened reinforced concrete frames by bridging behavior of local joints to the whole structure.Local confi nement effects due to varying retrofi tting schemes in the joints were simulated in the frame model.The seismic behavior factor was used to evaluate the seismic performance of the strengthened RC frames.The results demonstrated that the new proposed retrofi tting scheme was robust and promising,and fi nite element analysis appropriately captured the strength and global ductility of the frame due to upgrading of the local joints. 相似文献