首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
九龙江口水体中1995年有机物的转移   总被引:1,自引:0,他引:1  
1995年3个航次调查研究结果表明,九龙江口水体总有机物的含量受悬浮物含量控制。在S<5的低盐度区,悬浮泥沙和有机物产生明显的絮凝沉降;在S>5的广阔海域,它们的迁移接近于理想混合。估算得出九龙江河流的入海通量约:悬浮泥沙为9.8×105t/a;总COD为3.2×104t/a,其中溶解态COD为2.1×104t/a,约占2/3,为水体有机物的主要形态,如换算为溶解有机碳,则DOC的平均通量为3.2×104t/a。  相似文献   

2.
九龙江—厦门湾河口区溶解226Ra的分布   总被引:3,自引:0,他引:3  
利用锰纤维富集和直接射气法测定海水中226Ra的方法,对九龙江-厦门湾溶解226Ra的分布进行了一次调查。结果发现在河口区内溶解态的226Ra呈非保守行为,与世界上几大河流河口区226Ra的行为极为相似。在海门岛附近的水体中(S≈9)发现溶解态226Ra浓度最大,其值为0.598dpm/dm3,说明咸淡水在此处混合最激烈。本河口区溶解226Ra的最大值比Mississippi河的值小,比其他河流的值大2~5倍。  相似文献   

3.
九龙江口本中1995年有机物的转移   总被引:1,自引:0,他引:1  
陈松  廖文卓 《台湾海峡》1998,17(2):180-184
1995年3个航次调查研究结果表明,九龙江口水体总有机物的含量受悬浮物含量控制。在S〈5的低盐度区,悬浮泥沙和有机物产生明显的絮凝;在S〉5的广阔海域,它们的行移接近于理想混合。估算得出九龙江河流的入海一约;悬浮泥沙为9.8*10^5t/a;总COD为3.2*10^t/a,其中溶解态COD为2.1*10^4t/a约占2/3,为水体有机物的主要开矿如换算为溶解有机碳,则DOC的平均通量为3.2*10  相似文献   

4.
九龙江河口区磷的转移和入海通量   总被引:1,自引:3,他引:1  
1992~1993年4个航次的调查研究结果表明,九龙江河口区总磷的分布和转移受悬浮物含量明显控制。当SPM含量低时,其迁移过程接近理想行为;SPM含量高时则为非理想行为。估算得出,九龙江水体总磷的平均人海通量为1.47×103t/a。其中,溶解态磷为0.43×103t/a,约占29%;颗粒态磷占71%,九龙江水磷的输入以颗粒态为主。溶解态磷的分布,基本上在某一水平上了波动,其入海通量受环境影响很小,可能意味着颗粒磷的缓冲作用。  相似文献   

5.
九龙江河口区营养盐分布特征及其影响因素分析   总被引:2,自引:0,他引:2  
根据2009、2010年"丰水期"和"枯水期"四航次九龙江河口混合区的调查资料,且结合历史资料对营养盐含量及分布特征、周日变化特征进行了统计和相关分析,研究了九龙江流域营养盐输入海洋的变化过程,探讨九龙江河口营养盐伴随潮汐变化,以及河口混合过程中的生物地球化学行为。调查期间溶解无机氮、硅和磷含量的平面分布呈现出由径流冲淡水高值向河口外海端递减的变化趋势;在涨潮时,河口区感潮段高溶解无机氮、硅、磷营养盐的陆源冲淡水与低溶解无机氮、硅、磷营养盐外海水相遇,随着外海水的侵入,外海水的作用逐渐加强,在稀释混合过程中呈现出无机营养盐逐步降低的变化趋势,退潮时则相反;营养盐在这复杂的河口过程中往往表现出在水动力的作用下稀释混合是主要过程,无机氮和活性硅酸盐在河口稀释混合过程中呈现保守性特征,活性磷酸盐在河口转移(补充)过程的行为复杂化,呈现缓冲作用为主。  相似文献   

6.
胶体磷在河口区随盐度变化的研究   总被引:1,自引:0,他引:1  
陈丁  郑爱榕  陈敏 《海洋学报》2009,31(1):71-78
研究了胶体磷在河口海区随盐度变化的趋势,并将其与颗粒态、真溶解态磷随盐度的变化趋势进行对比,分析胶体态磷在河口的行为与颗粒态磷和真溶解态磷二者的异同。探讨磷在颗粒相、胶体相和真溶液相之间的分配及其与悬浮颗粒物浓度的关系,研究胶体磷在河口海区中的迁移转化作用。研究结果表明,胶体相中总磷、有机磷和活性磷浓度由河端向海端降低,表明陆源输入是其主要来源。胶体有机磷占总磷比例随盐度增加而下降,表明有机磷受胶体去除过程的影响较明显,胶体磷在河口海区的浓度变化趋势及胶体中有机磷和活性磷的比例都与真溶解相接近而与颗粒相差别较大。  相似文献   

7.
研究了胶体磷在河口海区随盐度变化的趋势,并将其与颗粒态、真溶解态磷随盐度的变化趋势进行对比,分析胶体态磷在河口的行为与颗粒态磷和真溶解态磷二者的异同.探讨磷在颗粒相,胶体相和真溶液相之间的分配及其与悬浮颗粒物浓度的关系,研究胶体磷在河口海区中的迁移转化作用.研究结果表明,胶体相中总磷、有机磷和活性磷浓度由河端向海端降低,表明陆源输入是其主要来源.胶体有机磷占总磷比例随盐度增加而下降,表明有机磷受胶体去除过程的影响较明显,胶体磷在河口海区的浓度变化趋势及胶体中有机磷和活性磷的比例都与真溶解相接近而与颗粒相差别较大.  相似文献   

8.
九龙江口生物可利用磷的行为与入海通量   总被引:6,自引:0,他引:6  
于1995年3、5月在九龙江口进行两个航次的现场调查,研究不同形态磷的河口行为,并估算生物可利用磷的入海通量。结果表明,在S<20区域内,溶解活性磷(DRP)的行为受控于“缓冲机制”,其含量在8~10μg/dm3水平上下波动。颗粒磷中MgCl2。可提取磷(MgCl2-P)含量随盐度增大而增大,并与叶绿素a以及悬浮物中Fe、Mn、Al含量呈正相关关系。NaOH/NaCl可提取磷(NaOH/NaCl-P)随盐度增大按指数关系下降,其含量与悬浮物中Fe、Mn、Al含量呈正相关关系。HCl可提取磷(HCl-P)在河口区的行为表现为保守混合。九龙江口生物可利用磷入海通量约517t/a,其中潜在生物可利用磷(PBAP)的贡献为溶解活性磷(DRP)的3倍。  相似文献   

9.
九龙江河口区有机物的转移和入海通量   总被引:3,自引:2,他引:3  
陈松  廖文卓 《台湾海峡》1996,15(3):260-264
1992-1993年4年个航次调查结果表明,九龙江河口区水体中总有机物的含量和转移与悬浮物含量密切相关。当SPM含量低时,其转移过程接近于理想行为;当SMP含量高时,同为非理想行为。  相似文献   

10.
本文讨论了2006年12月冬季和2007年8月夏季海南省万泉河、文昌/文教河河流及河口溶解态铝的含量、分布及季节差异。结果发现,万泉河冬、夏两季河流及河口溶解态铝的平均含量分别为(156±127)和(157±97)nmol/L,季节差异不明显。文昌/文教河冬、夏两季河流及河口溶解态铝的平均含量分别为(242±156)和(222±66)nmol/L,冬季溶解态铝的平均含量略高于夏季。万泉河溶解态铝在河海混合初期表现为清除行为,而后表现为保守混合行为,而文昌/文教河则表现出明显的非保守混合行为,在中等盐度区域存在明显外源输入,原因可能是八门湾底沉积物再悬浮过程中释放的影响。部分河流上游采样点由于受到人为活动引起的污水排放的影响,溶解态铝含量明显增加。万泉河、文昌/文教河溶解态铝的平均含量明显低于我国其他及世界主要河流。  相似文献   

11.
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.  相似文献   

12.
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.  相似文献   

13.
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.  相似文献   

14.
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.  相似文献   

15.
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.  相似文献   

16.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明:土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。  相似文献   

17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.  相似文献   

18.
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.  相似文献   

19.
20.
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号