共查询到20条相似文献，搜索用时 15 毫秒
1.
高墩梁桥的地震冲撞效应及其应对策略初探 总被引：1，自引：0，他引：1
国内外多次地震表明了高墩桥梁的地震冲撞破坏现象,针对目前国内大量兴建的高墩梁桥,有必要研究高墩梁桥地震冲撞效应和减轻桥梁地震冲撞破坏的应对策略。本文根据高烈度震区的1座高墩梁桥建立全桥的空间有限元模型,并在墩-梁结合部伸缩缝处采用非线性接触单元模拟相邻梁间的冲撞行为,同时考虑了下部支座的影响;考虑不同的强震动输入,采用非线性时程分析方法,研究了高墩梁桥的地震冲撞效应及减轻冲撞的有效措施。研究结果表明:本文采用的冲撞力学模型能够合理地模拟地震作用下结构的冲撞现象;冲撞行为对结构的地震反应影响复杂;地震动特性对冲撞效应影响显著;调整伸缩逢宽度或设置弹簧-阻尼限位装置可有效缓解结构间的冲撞效应。 相似文献
2.
Shear keys are used in the bridge abutments and piers to provide transverse restraints for bridge superstructures. Owing to the relatively small dimensions compared to the main bridge components (girders, piers, abutments, piles), shear keys are normally regarded as secondary component of a bridge structure, and their influences on bridge seismic responses are normally neglected. In reality, shear keys are designed to restrain the lateral displacements of bridge girders, which will affect the transverse response of the bridge deck, thus influence the overall structural responses. To study the influences of shear keys on bridge responses to seismic ground excitations, this paper performs numerical simulations of the seismic responses of a two-span simply-supported bridge model without or with shear keys in the abutments and the central pier. A detailed 3D finite element (FE) model is developed by using the explicit FE code LS-DYNA. The bridge components including bridge girders, piers, abutments, bearings, shear keys and reinforcement bars are included in the model. The non-linear material behaviour including the strain rate effects of concrete and steel rebar are considered. The seismic responses of bridge structures without and with shear keys subjected to bi-axial spatially varying horizontal ground motions are calculated and compared. The failure mode and damage mechanism of shear keys are discussed in detail. Numerical results show that shear keys restrain transverse movements of bridge decks, which influence the torsional–lateral responses of the decks under bi-axial spatially varying ground excitations; neglecting shear keys in bridge response analysis may lead to inaccurate predictions of seismic responses of bridge structures. 相似文献
3.
针对双薄臂高墩连续刚构桥两侧桥台处主梁与背墙的碰撞现象,基于桥台-背土作用简化模型和Kelvin碰撞模型,采用非线性时程法研究碰撞对双薄臂墩地震剪力、弯矩、曲率和位移,以及支座纵向变形的影响。提出可牺牲背墙、阻尼器、加强型横系梁等三种减碰措施,并对比分析其减碰效果。研究表明:碰撞会显著增大高墩的地震内力和曲率响应,降低墩顶位移和支座的纵向变形;碰撞刚度的变化对碰撞效应的影响在20%以内;可牺牲背墙和阻尼器两种减碰措施均可大幅降低桥墩的地震内力和曲率,使其接近不考虑碰撞时的状态,阻尼器同时还可以保护支座不超过容许变形,而可牺牲背墙则会导致支座的地震破坏;加强型横系梁不能发挥减碰作用,反而会增大桥墩的地震响应。 相似文献
4.
桥梁非线性地震反应分析若干问题研究现状 总被引：11，自引：1，他引：11
评述了钢筋混凝土桥墩非线性地震反应分析模型与损伤评估、桩－土－桥梁结构动力相互作用试验与理论研究和伸缩缝处的碰撞效应等问题的研究现状，指出了进一步的发展趋势。 相似文献
5.
针对非规则人字形桥梁在地震作用下灾变严重的问题,以一座非规则人字形桥梁为研究对象,建立其空间分析模型,研究综合考虑支座摩擦滑移、结构碰撞对非规则人字形桥梁地震响应的影响。结果表明:邻梁间的碰撞作用可使得桥梁墩顶位移及内力相比不考虑时有所减小,但同时也使梁体产生了较大的加速度脉冲效应;当考虑支座摩擦滑移和结构碰撞时,固定墩墩顶位移和邻梁相对位移峰值有一定程度增大,然而对梁体加速度脉冲效应结果影响并无统一规律;纵向地震波作用下,非规则人字形桥梁不仅存在顺桥向的碰撞,横桥向的碰撞响应也不容忽视。非规则人字形桥梁进行抗震设计计算时应选取符合实际情况的计算模型,考虑支座摩擦滑移及结构间的碰撞。 相似文献
6.
Damage investigation of small to medium-span highway bridges in Wenchuan earthquake revealed that typical damage of these bridges included: sliding between laminated-rubber bearings and bridge girders, concrete shear keys failure, excessive girder displacements and even span collapse. However, the bearing sliding could actually act as a seismic isolation for piers, and hence, damage to piers for these bridges was minor during the earthquake. Based on this concept, an innovative solation system for highway bridges with laminated-rubber bearings is developed. The system is comprised of typical laminated-rubber bearings and steel dampers. Bearing sliding is allowed during an earthquake to limit the seismic forces transmitting to piers, and steel dampers are applied to restrict the bearing displacements through hysteretic energy dissipation. As a major part of this research, a quarter-scale, two-span bridge model was constructed and tested on the shake tables to evaluate the performance of this isolation system. The bridge model was subjected to a Northridge and an artificial ground motion in transverse direction. Moreover, numerical analyses were conducted to investigate the seismic performance of the bridge model. Besides the test bridge model, a benchmark model with the superstructure fixed to the substructure in transverse direction was also included in the numerical analyses. Both the experimental and the numerical results showed high effectiveness of this proposed isolation system in the bridge model. The system was found to effectively control the pier-girder relative displacements, and simultaneously, protect the piers from severe damage. Numerical analyses also validated that the existing finite element methods are adequate to estimate the seismic response of bridges with this isolation system. 相似文献
7.
Evgueni T. Filipov Jessica R. Revell Larry A. Fahnestock James M. LaFave Jerome F. Hajjar Douglas A. Foutch Joshua S. Steelman 《地震工程与结构动力学》2013,42(9):1375-1394
Modern highway bridges in Illinois are often installed with economical elastomeric bearings that allow for thermal movement of the superstructure, and steel fixed bearings and transverse retainers that prevent excessive movement from service‐level loadings. In the event of an earthquake, the bearing system has the potential to provide a quasi‐isolated response where failure of sacrificial elements and sliding of the bearings can cause a period elongation and reduce or cap the force demands on the substructure. A computational model that has been calibrated for the expected nonlinear behaviors is used to carry out a parametric study to evaluate quasi‐isolated bridge behavior. The study investigates different superstructure types, substructure types, substructure heights, foundation types, and elastomeric bearing types. Overall, only a few bridge variants were noted to unseat for design‐level seismic input in the New Madrid Seismic Zone, indicating that most structures in Illinois would not experience severe damage during their typical design life. However, Type II bearing systems, which consist of an elastomeric bearing and a flat PTFE slider, would in some cases result in critical damage from unseating at moderate and high seismic input. The sequence of damage for many bridge cases indicates yielding of piers at low‐level seismic input. This is caused by the high strength of the fixed bearing element, which justifies further calibration of the quasi‐isolation design approach. Finally, the type of ground motion, pier height, and bearing type were noted to have significant influence on the global bridge response. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
8.
Experimental research and finite element analysis of bridge piers failed in flexure-shear modes 总被引：2，自引：1，他引：1
In recent earthquakes, a large number of reinforced concrete （RC） bridges were severely damaged due to mixed flexure-shear failure modes of the bridge piers. An integrated experimental and finite element （FE） analysis study is described in this paper to study the seismic performance of the bridge piers that failed in flexure-shear modes. In the first part, a nonlinear cyclic loading test on six RC bridge piers with circular cross sections is carried out experimentally. The damage states, ductility and energy dissipation parameters, stiffness degradation and shear strength of the piers are studied and compared with each other. The experimental results suggest that all the piers exhibit stable flexural response at displacement ductilities up to four before exhibiting brittle shear failure. The ultimate performance of the piers is dominated by shear capacity due to significant shear cracking, and in some cases, rupturing of spiral bars. In the second part, modeling approaches describing the hysteretic behavior of the piers are investigated by using ANSYS software. A set of models with different parameters is selected and evaluated through comparison with experimental results. The influences of the shear retention coefficients between concrete cracks, the Bauschinger effect in longitudinal reinforcement, the bond-slip relationship between the longitudinal reinforcement and the concrete and the concrete failure surface on the simulated hysteretic curves are discussed. Then, a modified analysis model is presented and its accuracy is verified by comparing the simulated results with experimental ones. This research uses models available in commercial FE codes and is intended for researchers and engineers interested in using ANSYS software to predict the hysteretic behavior of reinforced concrete structures. 相似文献
9.
After the occurrence of various destructive earthquakes in Japan, extensive efforts have been made to improve the seismic performance of bridges. Although improvements to the ductile capacities of reinforced concrete (RC) bridge piers have been developed over the past few decades, seismic resilience has not been adequately ensured. Simple ductile structures are not robust and exhibit a certain level of damage under extremely strong earthquakes, leading to large residual displacements and higher repair costs, which incur in societies with less-effective disaster response and recovery measures. To ensure the seismic resilience of bridges, it is necessary to continue developing the seismic design methodology of RC bridges by exploring new concepts while avoiding the use of expensive materials. Therefore, to maximize the postevent operability, a novel RC bridge pier with a low-cost sliding pendulum system is proposed. The seismic force is reduced as the upper component moves along a concave sliding surface atop the lower component of the RC bridge pier. No replaceable seismic devices are included to lengthen the natural period; only conventional concrete and steel are used to achieve low-cost design solutions. The seismic performance was evaluated through unidirectional shaking table tests. The experimental results demonstrated a reduction in the shear force transmitted to the substructure, and the residual displacement decreased by establishing an adequate radius of the sliding surface. Finally, a nonlinear dynamic analysis was performed to estimate the seismic response of the proposed RC bridge pier. 相似文献
10.
服役曲线梁桥常存在爬移病害。为探讨爬移病害程度对曲线梁桥抗震性能的影响规律,通过总结服役曲线梁桥爬移病害,确定以不同梁端爬移位移量作为描述服役曲线梁桥爬移状态的对比分析工况,并以一座三跨预应力混凝土曲线梁桥为例,采用MIDAS Civil建立有限元模型,考虑桩-土相互作用、双向碰撞效应及材料非线性,分析曲线梁桥支座及桥墩等主要受力构件地震响应规律,探讨爬移状态对服役曲线梁桥抗震性能影响。研究结果表明：主梁的爬移病害对桥梁的抗震性能会产生不利影响,会导致支座位移的增长,增加支座破坏的风险,从而增加桥梁上部结构碰撞效应及落梁风险;随着爬移位移的增加,桥墩的损伤状态可能由爬移前的无损伤转变为考虑爬移后的严重损伤状态。因此,在进行服役曲线梁桥抗震性能评估时应量化其爬移状态,并采用合理的措施对主梁的爬移进行限制。 相似文献
11.
Over the last two decades, the probabilistic assessment of reinforced concrete (RC) structures under seismic hazard has been developed rapidly. However, little attention has been devoted to the assessment of the seismic reliability of corroded structures. For the life‐cycle assessment of RC structures in a marine environment and earthquake‐prone regions, the effect of corrosion due to airborne chlorides on the seismic capacity needs to be taken into consideration. Also, the effect of the type of corrosive environment on the seismic capacity of RC structures has to be quantified. In this paper, the evaluation of the displacement ductility capacity based on the buckling model of longitudinal rebars in corroded RC bridge piers is established, and a novel computational procedure to integrate the probabilistic hazard associated with airborne chlorides into life‐cycle seismic reliability assessment of these piers is proposed. The seismic demand depends on the results of seismic hazard assessment, whereas the deterioration of seismic capacity depends on the hazard associated with airborne chlorides. In an illustrative example, an RC bridge pier was modeled as single degree of freedom (SDOF). The longitudinal rebars buckling of this pier was considered as the sole limit state when estimating its failure probability. The findings show that the life‐cycle reliability of RC bridge piers depends on both the seismic and airborne chloride hazards, and that the cumulative‐time failure probabilities of RC bridge piers located in seismic zones can be dramatically affected by the effect of airborne chlorides. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
12.
Past severe earthquakes indicate that pounding may cause considerable damage or even lead to collapse of colliding structures. The aim of this paper is to present an analysis of pounding between superstructure segments of an isolated elevated bridge induced by the propagating seismic wave. High-damping rubber bearings (HDRBs), used as isolation devices, are modelled by proposed non-linear formulation and the significance of the bearings model for pounding is indicated. The results of the study show that pounding leads to the increase or decrease of the forces acting on piers, depending on the gap size between superstructure segments. © 1998 John Wiley & Sons, Ltd. 相似文献
13.
以墩顶漂移率为指标运用ABAQUS有限元软件对钢筋混凝土桥墩进行地震易损性分析。对钢筋混凝土桥墩模型进行精细网格划分,运用循环往复Pushover方法模拟钢筋混凝土桥墩破坏界限值,以此界限值为标准对轴压比为0.20、0.22、0.24、0.26和0.30钢筋混凝土桥墩进行增量动力分析（IDA）。研究结果表明:结构的破坏超越概率,随着轴压比的增大而增大;考虑钢筋混凝土桥墩延性抗震性能,设计轴压比不宜超过0.30;轴压比为0.24~0.26时,钢筋混凝土桥墩破坏概率增加不大,宜为合理的轴压比。 相似文献
14.
为研究近断层地震动对曲线连续梁桥地震响应及碰撞效应的影响,采用非线性时程分析法,分别研究脉冲效应、上盘效应及方向性效应对某三跨曲线连续梁桥支座位移、桥墩内力及邻梁间碰撞力的影响;通过支座隔震率的对比分析,探究不同类型近断层地震动下地震响应产生差异的原因。研究结果表明:脉冲效应、上盘效应和方向性效应均会增大曲线连续梁桥地震响应,脉冲效应的影响尤为显著;脉冲效应和方向性效应削弱了高阻尼橡胶支座的隔震特性,而上盘效应对桥梁响应的影响仅与上盘地震动自身特性有关;综合来看,脉冲效应对曲线梁碰撞响应影响最明显,上盘效应影响不大。 相似文献
15.
地震作用下,相邻主梁间的碰撞会改变桥台-引桥-刚构连续梁桥结构体系的动力响应。为了探究主桥结构形式、墩高、引桥跨数和伸缩缝间距等结构参数对伸缩缝处碰撞效应和桥梁结构地震响应的影响,以某实际桥梁为背景,考虑碰撞能量耗散、桩土相互作用、桥台与台后填土相互作用以及支座和桥墩的非线性行为,采用CSIBridge建立桥台-引桥-刚构连续梁桥结构体系的有限元模型进行碰撞弹塑性动力分析。研究结果表明：不同主桥结构形式的主桥墩受力区别较大,相邻主桥墩高差较大时,选择连续梁桥结构体系更加合理。墩高增加使主引桥间动力差异增大,碰撞效应更加显著,仅对刚构墩受力影响较大。引桥跨数增多和伸缩缝间距增大分别使伸缩缝处碰撞效应增大和减小,碰撞抑制作用的增强和减弱也使得刚构墩内力和变形分别减小和增大,但对于其他桥墩基本无影响。 相似文献
16.
地震作用下隔震简支梁桥碰撞反应的振动台试验 总被引：2，自引：0，他引：2
由地震引发的碰撞是影响桥梁地震反应以及造成桥梁破坏的重要因素。本文对地震作用下隔震简支梁桥的碰撞反应进行了振动台试验。设计制作1个两跨简支的隔震梁桥模型,试验研究了梁间隙、邻梁质量比、隔震支座类型等参数对桥梁碰撞反应的影响。试验结果表明邻梁间隙、邻梁质量比、隔震支座类型等参数对桥梁的碰撞反应有着显著的影响。邻梁间隙越大,碰撞次数越少;邻梁质量比越大,撞击力越大。铅芯橡胶支座比板式橡胶支座耗能能力更强,可以有效降低邻梁之间的撞击力甚至避免碰撞发生。从而为桥梁防碰撞设计提供了可靠的试验依据。 相似文献
17.
Unseating of bridge girders/decks during earthquakes is very harmful to the safety and serviceability of bridges. Evidence from recent severe earthquakes indicates that in addition to damage along longitudinal direction, lateral displacement and rotation of bridge girders caused by pounding to adjacent girders can also lead to unseating. To simulate this effect, 3D modelling of the dynamic performance of whole bridge structures, including pounding, is needed strongly. This paper presents a 3D model that is practically suitable to precisely analyse pounding between bridge girders. Experiments have been conducted to verify the proposed pounding model. The 3D non‐linear modelling of steel elevated bridges is also discussed. A general‐purpose dynamic analysis program for bridges, namely dynamic analysis of bridge systems (DABS) has been developed. Seismic analyses on a chosen three‐span steel bridge are conducted for several cases including pounding as a case study. The applicability of the proposed pounding model is illustrated by the computations. The effects of poundings on the response of bridge girders are discussed and the computation results are given. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
18.
Effects of seismic isolation on the seismic response of a California high‐speed rail prototype bridge with soil‐structure and track‐structure interactions 
下载免费PDF全文
下载免费PDF全文 With the launch of the high‐speed train project in California, the seismic risk is a crucial concern to the stakeholders. To investigate the seismic behavior of future California High‐Speed Rail (CHSR) bridge structures, a 3D nonlinear finite‐element model of a CHSR prototype bridge is developed. Soil‐structure and track‐structure interactions are accounted for in this comprehensive numerical model used to simulate the seismic response of the bridge and track system. This paper focuses on examining potential benefits and possible drawbacks of the a priori promising application of seismic isolation in CHSR bridges. Nonlinear time history analyses are performed for this prototype bridge subjected to two bidirectional horizontal historical earthquake ground motions each scaled to two different seismic hazard levels. The effect of seismic isolation on the seismic performance of the bridge is investigated through a detailed comparison of the seismic response of the bridge with and without seismic isolation. It is found that seismic isolation significantly reduces the deck acceleration and the force demand in the bridge substructure (i.e., piers and foundations), especially for high‐intensity earthquakes. However, seismic isolation increases the deck displacement (relative to the pile cap) and the stresses in the rails. These findings imply that seismic isolation can be promisingly applied to CHSR bridges with due consideration of balancing its beneficial and detrimental effects through using appropriate isolators design. The optimum seismic isolator properties can be sought by solving a performance‐based optimum seismic design problem using the nonlinear finite‐element model presented herein. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
19.
斜交桥梁由于其不规则的结构形式使其受力规律与规则桥梁相比具有特殊性和复杂性,在地震作用下梁体的平动与转动存在弯扭耦合效应,导致结构动力响应分析复杂。针对斜交桥梁的结构特点,建立包含桩土相互作用的三维有限元模型,在考虑水平双向地震作用下,采用反应谱法及时程分析法对京包高速公路某互通式斜交桥梁进行地震反应分析。结果表明:互通式简支斜交桥梁的地震响应受地震动输入方向的影响较大,在考虑碰撞效应后,碰撞涉及结构部位的地震位移显著增加,地震内力也出现较大差异,即说明在斜交桥梁抗震设计时有必要适当考虑地震动输入方向和梁端与墩台及相邻梁端的碰撞效应。 相似文献