共查询到20条相似文献，搜索用时 171 毫秒
1.
《岩土力学》2017,(1):91-100
黏土在低水力坡降下偏离达西定律的现象及应力历史对土体变形的影响已为人们所认识,但能够同时考虑非达西渗流及应力历史影响的土体固结理论还很鲜见。在传统太沙基一维固结理论基础上,引入经典的Hansbo渗流模型,并考虑土体在不同应力状态下的变形特性,建立实际变荷载作用下土体的非线性固结模型。利用有限差分法对模型进行数值求解。在保证数值解可靠性的基础上,着重分析非达西渗流对超固结土固结性状的影响及非达西渗流下应力状态对固结性状的影响,并分析比较其异同点。结果表明:非达西渗流下超固结土的固结速率要比达西定律下慢,且随非达西渗流模型参数m、i_1值的增大,固结速率的减慢愈加明显;对考虑非达西渗流的不同应力状态土体而言,超固结土的固结速率最快,且超固结土在外荷载作用下产生的地基最终沉降值最小;对考虑非达西渗流的超固结土而言,前期固结压力越大、回弹再压缩指数越小,则土的固结速率越快,地基土的最终沉降值越小。 相似文献
2.
基于Wheeler土体各向异性旋转硬化法则,结合边界面理论,构造一个能够反映土体初始各向异性及加载后应力诱发各向异性的边界面本构模型,并借助ABAQUS软件提供的UMAT子程序接口,采用隐式积分算法--图形返回算法实现。通过对正常固结状态下（OCR=1）高岭土试样三轴不排水剪切试验进行模拟,并将模拟结果与ABAQUS自带的修正剑桥模型模拟结果进行了比较分析,表明本模型的模拟结果能够反映土体在偏压加载过程中产生的各向异性现象。在此基础上,采用本模型对中等超固结（OCR=4）高岭土试样三轴不排水剪切试验进行模拟,并再次与ABAQUS自带的修正剑桥模型模拟结果进行比较,表明本模型能够较好地反映中等超固结土在小应变情况下的非线性特性。相比于经典弹塑性模型,如修正剑桥模型,本模型的模拟结果更符合中等超固结土的变形特性。 相似文献
3.
K0固结饱和土柱孔扩张问题弹塑性分析 总被引：2，自引：0，他引：2
采用K0固结各向异性土体本构模型,将柱孔扩张后周围土体分为弹性区和塑性区,根据柱孔扩张理论和边界条件,推导出K0固结状态下饱和天然土体柱孔扩张问题弹塑性区的应力、塑性区半径以及超孔隙水压力的理论解答。同时,通过算例与修正剑桥模型解答进行对比分析,结果表明,土的不同初始固结状态对柱孔扩张后孔周围的应力和超孔隙水压力产生很大影响,采用考虑K0固结诱发各向异性土体本构模型所得到的应力和超孔隙水压力解答大于修正剑桥模型的解答,但塑性区影响半径却明显小于后者。 相似文献
4.
5.
天然土体经历开挖卸荷应力路径后,其应力变形特性与常规加载应力路径条件下规律存在较大差异。目前常用土体本构模型大多建立在等向固结单向加载三轴试验基础上,没有考虑初始K0固结和开挖卸荷应力路径的影响。以剑桥模型为基础,借鉴关口-太田模型的建模思想,通过引入新的应力比参数,对p-q平面上屈服轨迹硬化轴进行旋转,调整弹性区范围,以反映初始K0固结的影响;再运用变换应力法将模型三维化处理,从而使模型可以描述土体三向不等向应力状态,最终得到一个能综合反映土体K0固结开挖卸荷应力-应变特性的三维弹塑性本构模型。通过和典型室内应力路径试验结果进行对比,验证了模型的合理性。 相似文献
6.
7.
8.
建筑桩基的有效应力地震反应分析：Ⅰ--计算方法 总被引：1，自引：1，他引：0
根据地震作用、上部结构、桩基的特点,建立了建筑桩基地震反应分析的计算模型,考虑了桩-土-上部结构的动力相互作用。然后将饱和土体视为由固、液二相组成的两相介质,基于Biot动力固结方程,提出一种建筑桩基地震反应的有效应力动力分析方法,并给出了具体计算步骤。 相似文献
9.
考虑温度影响的非饱和土本构模型 总被引：1，自引：1，他引：0
首先建立了反映温度对非饱和土前期固结压力影响的加载-升温(loading thermal, LT)屈服线,而后基于真强度概念并结合潜在强度的确定方法推导出不同温度下非饱和黏土临界状态应力比的理论计算公式;将LT屈服线与反映常温下吸力对土体前期固结压力影响的加载-湿陷(loading collapse, LC)屈服线结合,建立了加载-升温-湿陷(loading thermal collapse, LTC)屈服面,该屈服面综合考虑了温度和吸力对土前期固结压力的影响;最后在临界土力学框架内建立了一个考虑温度影响的正常固结非饱和土本构模型,并将其扩展到超固结非饱和土。与巴塞罗那模型相比,所提出的模型仅增加了一个参数来反映非饱和土的前期固结压力随温度升高而降低的特性。模型能够综合描述温度、吸力以及不同超固结程度对土应力、应变的影响,方便于数值计算和有限元分析。模型预测和试验分析表明,某一固定吸力下升温会使正常固结非饱和土强度提高;对于超固结非饱和土,升温或湿化均会破坏土体超固结,降低软化和剪胀的效果。 相似文献
10.
土体结构性的数学模型是21世纪土力学的核心问题。由于土体微观结构的变化造成了重塑土与原状土的力学特性上的差异。采用应变型和应力型结构性宏观参数来表征这种微观结构的变化,同时将应变性结构性参数引入到等向固结过程中去,用以描述常规三轴试验中剪切前的等向固结过程以及剪切时球应力对结构性土体的影响。实现应变型和应力型结构性宏观参数对整个三轴剪切过程的描述。修正剑桥模型对正常固结重塑黏土的三轴压缩试验能做出准确地描述,但对超固结黏土及原状土,即具有结构地土体,则不能给出准确地描述。将应变型和应力型结构性宏观参数引入到修正剑桥模型中,实现修正剑桥模型的结构化。该结构性修正剑桥模型参数的确定方法与常规修正剑桥模型参数的确定方法相差不多,只不过多了球应力与土体结构性体应变的关系式、偏应力与土体结构性广义剪应变的关系式。经过数值模拟比较,结构性修正的剑桥模型能较好地反映原状土的结构性演化过程,能描述原状土结构的整个破坏过程,在多种应力路径下具有很好的预测作用。 相似文献
11.
The performance of several soil constitutive models was evaluated by comparing experimental results and simulated behavior of a medium plasticity clay. Input parameters for the soil constitutive models were obtained from triaxial compression and extension tests on normally and overconsolidated medium plasticity clay. The soil models employed for this study were the Cam Clay, Modified Cam Clay, 3-SKH, and S-CLAY1 models. In order to investigate the influence of some of the input parameters on the performance of the models, sensitivity analyses were also performed. The comparisons demonstrate that the Cam Clay model was able to predict the normally consolidated compressive behavior of medium plasticity clay. Both 3-SKH and Cam Clay models were able to produce acceptable predictions for stress?Cstrain and stress path behavior for overconsolidated compression of the soil. The 3-SKH model did not perform satisfactorily for predicting pore pressure variations, while the Cam Clay model demonstrated fairly acceptable predictions. For the normally consolidated reduced extension test, the Modified Cam Clay and S-CLAY1 models performed better than the Cam Clay and 3-SKH models in predicting the stress?Cstrain curve, pore pressure variations, and stress path. 相似文献
12.
Experimental results and simulated behavior of a medium plasticity clay were compared to investigate the performance of an advanced soil constitutive model. The soil model employed for this study was the 3-SKH model. The performance of this model was compared to the performance of two other critical state models; the Cam Clay (CC) and Modified Cam Clay (MCC) models. In addition, the influences of some of the input parameters on the performance of the 3-SKH model were investigated by performing sensitivity analyses. The comparisons demonstrated that the CC model was able to predict normally consolidated compressive behavior of the remolded medium plasticity clay. The compression behavior of overconsolidated clay was better captured by both the 3-SKH and CC models. For extension behavior of the normally consolidated samples, the MCC model performed better than the CC and 3-SKH models in predicting the stress path. The 3-SKH model was found to be very sensitive to varying the exponent in the hardening function. In particular, a difference between the evaluated values as small as 0.01 had a noticeable effect on the predicted stress–strain values for the overconsolidated compression and extension samples. 相似文献
13.
A critical state model for overconsolidated structured clays 总被引：1，自引：0，他引：1
This paper presents a generalised critical state model with the bounding surface theory for simulating the stress–strain behaviour of overconsolidated structured clays. The model is formulated based on the framework of the Structured Cam Clay (SCC) model and is designated as the Modified Structured Cam Clay with Bounding Surface Theory (MSCC-B) model. The hardening and destructuring processes for structured clays in the overconsolidated state can be described by the proposed model. The image stress point defined by the radial mapping rule is used to determine the plastic hardening modulus, which varies along loading paths. A new proposed parameter h, which depends on the material characteristics, is introduced into the plastic hardening modulus equation to take the soil behaviour into account in the overconsolidated state. The MSCC-B model is finally evaluated in light of the model performance by comparisons with the measured data of both naturally and artificially structured clays under compression and shearing tests. From the comparisons, it is found that the MSCC-B model gives reasonable good simulations of mechanical response of structured clays in both drained and undrained conditions. With its simplicity and performance, the MSCC-B model is regarded as a practical geotechnical model for implementation in numerical analysis. 相似文献
14.
The yield locus governing the stress–strain response of a soil may degrade during rebound at high overconsolidation ratios. The cause can be attributed to a breakdown in bonding. A Cam–Clay model is applied to account for the degrading yield locus, and the influence of this degradation is assessed using a theoretical approach for friction pile capacity. Stress changes in the soil continuum due to pile installation and setup are simulated by cylindrical cavity expansion and radial consolidation, anda segment loading model is used to determine the effective stress change in the soil at peak load transfer under undrained conditions. The results indicate that plastic rebound affects peak load transfer to at least the same extent as shear strength. 相似文献
15.
16.
This paper presents a two-surface plasticity model for describing some important features of saturated clay under cyclic loading conditions, such as closed hysteresis loops, cyclic shakedown and degradation, and different stress–strain relations for two-way loading. The model, namely ACC-2-C, is based on the elastoplastic model ACC-2 (an adapted Modified Cam Clay model with two yield surfaces) developed by Hong et al. (Acta Geotech 11(4):871–885, 2015). The small-strain nonlinearity concept is adopted to achieve the nonlinear characteristics of clay during unloading–loading stage. The new hardening law related to accumulated deviatoric plastic strain is proposed for the inner surface to describe the cyclic shakedown and degradation. Following the advantages of the ACC-2 model, the constitutive equations are simply formulated based on the consistency condition for the inner yield surface. The model is conveniently implemented in a finite element code using a stress integration scheme similar to the Modified Cam Clay model. The simulation results are highly consistent with experimental data from drained and undrained isotropic cyclic triaxial tests in normally consolidated saturated clay under both one-way and two-way loadings.
相似文献17.
The paper presents numerical simulations investigating the settlement reduction caused by stone columns in a natural soft clay. The focus is on the influence of the soft soil alteration caused by column installation. A uniform mesh of end-bearing columns under a distributed load was considered. Therefore, the columns were modelled using the “unit cell” concept, i.e. only one column and the corresponding surrounding soil in axial symmetry. The properties of the soft clay correspond to Bothkennar clay, which is modelled using S-CLAY1 and S-CLAY1S, which are Cam clay type models that account for anisotropy and destructuration. The Modified Cam clay model is also used for comparison. Column installation was modelled independently to avoid mesh distortions, and soft soil alteration was directly considered in the initial input values. The results show that the changes in the stress field, such as the increase of radial stresses and mean stresses and the loss of overconsolidation, are beneficial for high loads and closely spaced columns but, on the contrary, may be negative for low loads, widely spaced columns and overconsolidated soils. Moreover, whilst the rotation of the soil fabric reduces the settlement, in contrast the soil destructuration during column installation reduces the improvement. 相似文献
18.
A shortcoming of the hypoplastic model for clays proposed by the first author is an incorrect prediction of the initial portion
of the undrained stress path, particularly for tests on normally consolidated soils at isotropic stress states. A conceptually
simple modification of this model, which overcomes this drawback, is proposed in the contribution. The modified model is applicable
to both normally consolidated and overconsolidated soils and predicts the same swept-out-memory states (i.e., normal compression
lines) as the original model. At anisotropic stress states and at higher overconsolidation ratios the modified model yields
predictions similar to the original model. 相似文献
19.
循环荷载作用下超固结软黏土软化-孔压模型研究 总被引：1，自引：0，他引：1
随着循环次数的增加,循环荷载作用下正常固结软黏土孔隙水压力逐渐增加,而孔压的增加将导致土体发生软化现象。对于超固结软黏土,循环荷载作用下在循环初期将产生负孔压,而此时也发生循环软化现象,这显然与有效应力原理是相矛盾的。以往的研究往往通过建立软化指数与循环次数的关系来描述土体的循环软化特性,从而不能反映土体的循环过程中残余孔压变化对土体循环软化的影响。通过对杭州饱和软黏土进行应力控制的循环三轴试验,对循环荷载作用下超固结软黏土的软化特性及孔压发展规律及两者关系进行了研究。在试验的基础上建立了超固结软黏土循环软化-孔压模型,该模型反映了残余孔压增长对超固结软黏土循环软化特性的影响规律。 相似文献
20.
土结构性是土结构空间排列几何特征和联结特征所表现出的力学性质,是影响土力学特性的重要内在因素。它与土的密度、粒度、湿度相联系,能够综合反映土的强度、变形等力学特性的变化和发展。从综合反映增湿导致土结构内在主动变化和加载变形导致土结构被动变化两个方面出发,沿用土综合结构势的应力比结构性参数,首先建立压缩、剪切及增湿作用下黄土的结构性演化规律;其次,通过压剪湿作用下黄土的应力-应变特性、屈服破坏特性及其与结构性之间的关系,揭示结构性变化对土力学性质的影响;进而,建立了反映压剪湿作用下黄土结构性发展演化的湿载结构性本构模型。最后通过与试验数据、修正剑桥模型的比较分析,初步验证该模型的准确性。 相似文献