共查询到20条相似文献，搜索用时 453 毫秒
1.
通过全岩化学分析、显微镜下鉴定、扫描电镜分析及矿物自动定量分析(AMICS),查明了断峰山铌钽矿床的矿石物质组成和铌钽赋存状态.矿石Nb2O5品位为0.0112％～0.0117％,Ta2O5品位为0.0033％～0.0084％,主要矿物组成为钠长石、石英、白云母、黑云母及高岭石等,矿石中的铌钽矿物主要有钽锰矿(Ta/Nb=2.94,Fe/Mn=0.45)、钽铌锰矿(Ta/Nb=0.51,Fe/Mn=0.56)和铌锰矿(Ta/Nb=0.11,Fe/Mn=0.82)3种.矿石含Nb2O5量为0.0112％～0.0117％,含Ta2O5量为0.0033％～0.0084％,该矿床为花岗伟晶岩类铌钽矿床.铌在铌锰矿、钽铌锰矿和钽锰矿分布率分别为48.76％、37.26％和13.99％.钽在钽锰矿、钽铌锰矿和铌锰矿的分布率分别为62.65％、28.96％和8.39％.铌钽矿物粒度主要分布于16～75μm之间,矿物单体解离度较低,占24.47％. 相似文献
2.
一、原理含锰矿物种类较多,分布普遍,但具有经济价值的锰矿物,主要是锰的氧化物和碳酸盐。其主要矿物有硬锰矿、软锰矿、黑锰矿、水锰矿、菱锰矿等。这些锰矿物一般都能与盐酸作用,其化学反应式为: 2 MnO_2+4HCl→2 MnCl_2+2H_2O+O_2 MnCO_3+2 HCl→MnCl_2+H_2O+CO_2 锰矿物与盐酸作用后的溶液,经干涸后,易生成氯化锰和含水氯化锰晶体,可在正交偏光显微镜下,根据其晶体形状、光性和潮解转变等特征加以鉴别。二、方法该方法只需一台偏光显微镜、酒精灯和数片载物片,以及20～50％的盐酸一滴瓶。其步骤是:刻取粒径为1毫米左右的矿物或矿石置于载物片上,滴入20～50％盐酸,移于酒精灯上缓缓加热 相似文献
3.
铜精矿经混合酸消解溶样处理，标准溶液中加入一定含量的Cu、Fe进行基体匹配，电感耦合等离子体发射光谱法测定矿样中的银、砷、铅、锌。方法基体效应较小，各待测元素之间没有明显干扰，用于分析有证标准物质和实际样品，分析结果与推荐值和其他常规方法测定值一致，均在允许误差范围内。方法的回收率为Ag87％～95％、As91％～103％、Pb92％～110％、Zn88％～108％，方法的精密度（RSD，n=12）为0．55％-1．52％。与现行的单元素分析方法相比，建立的方法分析周期短，适用于大宗铜精矿商品进出口的检验。 相似文献
4.
发射光谱法测定勘查地球化学样品中银硼锡钼铅 总被引：21，自引：13，他引：21
以K2S2O7、NaF、Al2O3和炭粉为缓冲剂，Ge为内标，电弧发射光谱法测定勘查地球化学样品中Ag、B、Sn、Mo、Pb。方法检出限为Ag0．013μg／g、B0．83μg/g、Sn0．23μg／g、Mo0．073μg/g、Pb0．37μg／g。方法精密度（RSD，n=12）为Ag4．2％～11．3％、B3．2％～6．5％、Sn2．6％～7．1％、Mo2．9％～6．3％、Pb1．57％～5．18％。测定了国家一级地球化学标准物质，结果与标准值相符。 相似文献
5.
多目标地球化学调查土壤样品中氮和碳的快速测定 总被引：2，自引：1，他引：2
详细研究了元素分析仪的工作条件，建立了直接固体进样同时测定多目标地球化学调查土壤样苎支氮、碳的方法。方法简便、快速，检出限为氮14．5μg／g、碳0．013％。经土壤国家一级标准物质分析验证，测定值与标准值相符，精密度（RSD，n=12）为氮1．49％-3．27％、碳0.64％～3.63％。 相似文献
6.
电感耦合等离子体发射光谱法直接测定黄铜矿中多元素 总被引：12，自引：12，他引：12
应用电感耦合等离子体原子发射光谱法直接测定黄铜矿中Cu、Fe、Cd、Co、In、Mn、Ni、Pb和Zn9种元素。试样经HCl-HNO3溶解，不需要化学分离，用干扰系数校正法消除黄铜矿中主量元素Cu和Fe对其它微量元素的干扰，以国家一级标准物质GBW 07268检验方法的准确度，结果与标准值相符，相对误差除Ni元素外，其它均小于5．00％，精密度(RSD，n=8)为2．55％～7．62％。 相似文献
7.
电感耦合等离子体原子发射光谱法同时测定沉积岩中15个元素 总被引：2，自引：10，他引：2
采用电感耦合等离子体原子发射光谱法同时测定沉积岩样品中K、Na、Ca、Mg、Fe、Mn、Ni、V、Ga、Cu、Zn、Sr、Ba、Cr和B等15个元素。在应用混合酸处理样品的过程中，加入适量的甘露醇能够抑制硼的挥发。在优化选定的仪器条件中，15个元素的检出限为0．0010-0．032mg／L。对岩石国家一级标准物质GBW 07105～GBW 07108进行检测，各元素的测定值与标准值吻合。方法的回收率为93．3％～106．0％，测定结果的相对标准偏差（RSD，n=10）均小于5．2％。 相似文献
8.
熔融制片-X射线荧光光谱法测定锰矿样品中主次量元素 总被引：6，自引：0，他引：6
采用混合熔剂熔融制备样片，加入碘化铵粉末，有效地驱赶了锰矿熔融制样时产生的大量气泡，用Axios型X射线荧光光谱仪测定锰矿样品中的Mn、Fe、Si、Al、Ti、Ca、Mg、Na、K、P、Ba、Cu、Zn、Ni等元素的氧化物含量，用理论a系数校正基体效应，方法简便快捷。用国家一级锰矿石标准物质GBW 07266验证，结果与标准值相符；以锰矿石考察方法的精澈（RSD，n=12），除CuO为10．05％，其余各组分均≤8％。 相似文献
9.
发射光谱法快速测定银锡铜铅锌钼铍 总被引：4，自引：9，他引：4
使用两台摄谱仪同时接收光谱，以K2S2O7、NaF、Al2O3为缓冲剂，Ge、Sb为内标，测定化探样品中7项元素，检出限(μg／g)分别是：Ag0．02，Sn0．5，Cu 1，Pb 2，Zn 10，Mo 0．2，Be 0．5；精密度(RSD，n=20)在2．9％～16．8％。采用国家一级标准物质验证方法可靠性，测定结果与标准值一致。 相似文献
10.
全谱直读等离子体发射光谱法测定高纯金中的杂质元素 总被引：3，自引：0，他引：3
用新型号的全谱直读等离子体发射光谱仪测定了高纯金中的杂质元素，进行了分析谱线的选择，功率、气体流量等工作条件的优化，选用内标法校正标准溶液与样品溶液基体不同的影响。取样量为0．5g时，方法的测定下限为0．02～4．67μg/g，回收率在90％～101％，当待测元素含量大于5μg/g时，分析结果的相对标准偏差小于5％。方法用于实际样品的分析，结果与其他方法相符。 相似文献
11.
S. Viswanathan K. Surya Prakash Rao B. Mahabaleswar 《Journal of the Geological Society of India》2013,82(6):621-627
Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours. 相似文献
12.
奥地利安东帕有限公司 《岩矿测试》2009,28(3):306-306
最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提 相似文献
13.
14.
E. M. Prasolov S. A. Sergeev B. V. Belyatsky E. S. Bogomolov K. A. Gruzdov I. N. Kapitonov R. Sh. Krymsky V. O. Khalenev 《Geochemistry International》2018,56(1):46-64
This paper reports the first results of a study of 11 isotope systems (3He/4He, 40Ar/36Ar, 34S/32S, 65Cu/63Cu, 62Ni/60Ni, 87Sr/86Sr, 143Nd/144Nd, 206–208Pb/204Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others. 相似文献
15.
Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance. 相似文献
16.
17.
Alexander E. C. Broberg J. S. Kehren A. R. Graziani M. M. Turri W. L. 《Environmental Geology》1993,22(4):353-361
Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×106 1 of partially treated effluent and about 600 m3 of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes. 相似文献
18.
Mercury,arsenic, antimony,and selenium contents of sediment from the Kuskokwim River,Bethel, Alaska,USA 总被引：1，自引：0，他引：1
The Kuskokwim River at Bethel, Alaska, drains a major mercury-antimony metallogenic province in its upper reaches and tributaries. Bethel (population 4000) is situated on the Kuskokwim floodplain and also draws its water supply from wells located in river-deposited sediment. A boring through overbank and floodplain sediment has provided material to establish a baseline datum for sediment-hosted heavy metals. Mercury (total), arsenic, antimony, and selenium contents were determined; aluminum was also determined and used as normalizing factor. The contents of the heavy metals were relatively constant with depth and do not reflect any potential enrichment from upstream contaminant sources. 相似文献
19.
滇东南锡、银、铅、锌多金属矿床主要分布在个旧、白牛厂、都龙3个矿区,而滇东南较大的3个花岗岩体又分别出露在3个矿区或附近.花岗岩体均形成于燕山晚期,岩石化学、矿物成分相似,富含锡、银、铅、锌、钨、铜等成矿元素.矿床主金属元素组合与岩体之间的距离由远而近出现由锡、钨、(铍、铌、钽)→锡、钨、(铁)、铜、铟→锡、铅、锌、银、铟、(锑)有规律的变化.花岗岩浆是成矿物质来源和成矿热源.岩浆侵入初期使上覆地层隆起产生背斜(凹陷部位成向斜);同时使地层产生一系列裂隙、压性断层或层间断裂;岩浆侵入晚期,这些断层再次活动,表现为张性,岩浆产生的含矿热液沿由其活动所造成的断裂迁移、充填、交代、沉淀而形成矿床. 相似文献
20.
岩石密度和超高压岩石折返速率 总被引：1，自引：3，他引：1
在常温常压条件下对中国大陆科学钻CCSD主孔100-3000米岩心样品进行了密度测量,建立了密度连续剖面,并界定了不同超高压岩石的密度值。通过对比高温高压物性实验资料,岩石密度随着退变程度增强而降低,榴辉岩密度变化序列为3.52g/cm3→3.49g/cm3→3.07g/cm3→2.93g/cm3。超高压长英质岩石密度变化序列为3.00g/cm→2.80g/cm3→2.65g/cm3。上述实验资料是讨论不同折返阶段岩石所受浮力的基础,为研究折返速率大小提供了基本参数。本文通过折返板块运动平衡时,上浮力与粘滞力平衡这一关系式,定量研究了大陆俯冲板块的折返速率,认为密度差产生上浮力从而引起折返,温度对板块折返速率的影响最为显著;密度差大小、折返角度、折返板块大小对折返速率也有直接的影响。定量模拟分析表明,在温度高于850℃时,板块的折返速率可以超过100mm/a;当温度降至700℃时,折返速率则低于1.5mm/a。作者认为在折返早期,温度较高,板块快速折返至60-70km榴辉岩相深度;随着传导散热,温度降低,板块以较慢的速率折返至中下地壳。折返速率的估算表明,浮力是板块折返第一阶段(从>100km深部折返至<40km的中下地壳)的主要驱动力。 相似文献