首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 62 毫秒
1.
Static stability mainly against sliding of a typical, relatively large skirted gravity structure was investigated using three-dimensional finite element modeling. The numerical model was validated against centrifuge test results. A specific set of dimensions was chosen to model a typical skirted gravity structure in a centrifuge with two types of foundation soils: uniform saturated sand and a clay zone sandwiched between two sand layers. Soil shear strength parameters used in the finite element models were estimated from in-flight cone penetration resistance measurements obtained in the centrifuge. Numerical parametric studies were conducted using the validated finite element model. The parameters included were the depth and strength of the clay zone and the inclination of external load. It is shown that a relatively simple three-dimensional finite element model was effective in providing information that would be needed to design such a critical and expensive offshore structure. Basic Mohr-Coulomb strength parameters and moduli based on cone penetration resistance measurements and published empirical correlations were appropriate in modeling the soils in the finite element simulations.  相似文献   

2.
Abstract

Evaluation of the strength of cement-treated clay with a broad range of mix ratios and curing periods was conducted using unconfined compression tests (UCTs). The influence of cement content, total water content, and curing period on the unconfined compressive strength of cemented clay are investigated. It is found that, at constant total water content, higher cement content results in higher unconfined compressive strength, while the total water content has an opposite effect. A power function can be used to correlate the unconfined compressive strength with the cement content or the total water content. For a fixed mix ratio, the unconfined compressive strength of cement-stabilized clay increases with the curing period, the effect of which can be characterized by a semi-log formula. Also, a strength-prediction model that considers both mix ratios and curing periods for cement-admixed marine clay is developed and validated; the model can capture the effect of clay type by considering the plastic index of untreated soils. It is also proved that the proposed framework for strength development is also applicable for other cement types.  相似文献   

3.
Abstract

River-dredged sludge has a high water content and minimal bearing capacity and strength. Adding cement, fly ash, and slag to dredged sludge as a combined curing agent can quickly reduce its water content and improve its strength. This study experimentally investigates the solidification effectiveness of different proportions of curing agents using methods including electron microscopy, particle size analysis, water ratio limit, and water content and direct shear tests. The water content and shear strength of different combined curing agents are obtained at different ages. We find that an optimum curing agent combination exists. With increases in fly ash and slag content, test results indicate that the water content of solidified sludge first decreases and then increases, whereas the shear strength first increases and then decreases, allowing an optimal combination curing agent to be obtained. When using industrial waste residue as curing agent, it is necessary to consider the negative effects of the curing agent to better control the dosage so as to achieve better curing effect.  相似文献   

4.
ABSTRACT

In this paper, a series of mini-drum centrifuge experiments on motion of submarine debris flow, which are able to correctly reproduce the self-weight stresses and gravity-dependent processes, are presented. These tests were performed using artificial submarine clay with high water content, from 93 to 149%. The extremely low shear strength made the debris material behave as idealistic lubricating material when it was deposited, resulting in a linear relationship between water content and runout distance of strongly coherent debris flow. On the other hand, the dilation of the flow body and hydroplaning was observed for weakly coherent debris flow, which further increased the mobility of flow body. A densimetric Froude number Frd was used to indicate the threshold of hydroplaning, which occurs if the Frd is greater than 0.2. Finally, two simple analytical models based on prototype debris flow under 1?g condition was used to validate the experiment results, which further prove the effects of soft marine clay on the high mobility of submarine debris flow. On the other hand, when the water content exceeded 120%, the experiment results deviated from the analytical solution due to the effects of hydroplaning.  相似文献   

5.
Abstract

A series of direct shear tests were performed on cement-admixed silty clay to investigate the effect of cement content and nano-magnesia (MgO) on its shear strength properties. For each normal stress, shear strength increased with cement content. However, an obvious increment in shear strength was achieved when the cement content was adjusted from 13% to 17%. Both cohesion and friction angle of cemented soil increased with cement content, and exponential function was adopted to correlate both the factors with cement content. For cement content of 10% investigated in this study, the optimum nano-MgO content was 10‰, wherein the cohesion could reach the peak value. The microstructure of the mixture revealed that the structure of the mixture was compacted for the optimum nano-MgO content. However, micro-cracks were formed when the amount of nano-MgO exceeded its optimum content.  相似文献   

6.
ABSTRACT

Natural Ariake clays are characterized by high sensitivity. In this study, the mechanism and the factors controlling undrained shear strengths of both undisturbed and remolded Ariake clays are discussed. A series of unconfined compressive tests were performed on undisturbed samples of natural Ariake clays. The remolded undrained shear strength is predicted using a quantitative expression derived from extensive data of remolded undrained shear strength for a number of soils compiled from resources in the literature. The sensitivity of natural Ariake clays derived from the ratio of half of unconfined compressive strength for undisturbed samples to remolded undrained shear strength is found to be affected by both natural water content and normalized water content that is defined as the ratio of natural water content to liquid limit. The smaller the natural water content, the higher the sensitivity is at the same normalized water content. At the same natural water content, the larger the normalized water content, the higher the sensitivity is.  相似文献   

7.
非结构化网格下近岸波生流数值模拟   总被引：5，自引：2，他引：3  
唐军  魏美芳 《海洋学报》2010,32(6):41-46
波浪破碎产生的近岸流是近岸海域关键的水动力因素之一。基于近岸波浪的椭圆型缓坡方程和二维近岸波生流方程,建立了非结构化网格下近岸波浪破碎形成的近岸流数值模型。数值模型中,在空间上采用有限体积法进行数值离散,在时间上采用欧拉向前格式数值离散。数值计算结果表明,该数值模型可以有效地模拟近岸波浪破碎产生的近岸流。  相似文献   

8.
四叉树网格下的椭圆型缓坡方程数值模型研究   总被引：1，自引：1，他引：0  
唐军  李巧生  沈永明 《海洋学报》2013,35(5):162-168
波浪是近岸海域关键的水动力因素之一。考虑到近岸地形复杂、波浪演化显著的特点,建立了四叉树网格体系下的椭圆型缓坡方程数值模型,采用有限体积法对模型进行数值离散,应用GPBiCG(m, n)算法求解离散后的控制方程。模型中根据波浪波长布局计算网格,生成多层次四叉树网格,对复杂计算域有较好的适应性,并且在离散和方程求解中无需引入形函数、不产生复杂的交叉项,节约了存储空间和计算时间。将模型成功应用于物理模型实验及Acapulco海湾的波浪场数值模拟,结果表明该模型能够准确、高效地模拟近岸波浪场,可为近岸波浪场的模拟提供一定的理论和技术支持。  相似文献   

9.
Large Eddy Simulation for Wave Breaking in the Surf Zone   总被引：1，自引：0，他引：1  
In this paper, (he large eddy simulation method is used combined with the marker and cell method to study the wave propagation or shoaling and breaking process. As wave propagates into shallow water, the shoaling leads lo the increase of wave height, and then at a certain position, the wave will be breaking. The breaking wave is a powerful agent for generating turbulence, which plays an important role in most of the fluid dynamic processes throughout the surf zone, such as transformation of wave energy, generation of near-shore current and diffusion of materials. So a proper numerical model for describing the turbulence effect is needed. In this paper, a revised Smagorinsky subgrid-scale mode! is used to describe the turbulence effect. The present study reveals that the coefficient of the Smagorinsky model for wave propagation or breaking simulation may be taken as a varying function of the water depth and distance away from the wave breaking point. The large eddy simulation model presented in this pape  相似文献   

10.
1.IntroductionIn mathematics and physics,a soliton is a self-reinforcing solitary wave caused by nonlinear ef-fectsinthe medium.Solitons are found in many physical phenomena(Chou and Shih,1996;Chouand Quyang,1999;Chouet al.,2003;Chenet al.,2004;Wang,2004;…  相似文献   

11.
Abstract

Newly dredged fills feature a high moisture content and a high floating mud content. Based on the conventional vacuum preloading (CVP) method, this article presents a new method of air-booster vacuum preloading (AVP) to reinforce newly dredged fills for different air-booster periods (45, 60 and 90?min). Compared with other methods, this new method features no sand cushion and adopts a self-developed air-booster pipe and a water–air separation device. A series of laboratory model tests were performed to explore the effect of the improved AVP method for the enhancement of newly dredged fills. A comparison of variables monitored during reinforcement (vacuum pressure, surface settlement, water discharge and pore-water pressure) and after reinforcement (water content, vane shear strength, SEM and MIP) indicates that the reinforcement effect of the AVP method is superior to that of the CVP method; the former can effectively alleviate the problem of prefabricated vertical drain (PVD) clogging, greatly reducing engineering costs and significantly shortening construction periods.  相似文献   

12.
Modeling of the Turbulence in the Water Column under Breaking Wind Waves   总被引：1，自引：0，他引：1  
Past studies have shown that there is a wave-enhanced, near-surface mixed-layer in which the dissipation rate is greater than that derived from the “law of the wall”. In this study, turbulence in water columns under wind breaking waves is investigated numerically and analytically. Improved estimations of dissipation rate are parameterized as surface source of turbulent kinetic energy (TKE) for a more accurate modelling of vertical profile of velocity and TKE in the water column. The simulation results have been compared with the experimental results obtained by Cheung and Street (1988) and Kitaigorodskii et al. (1983), with good agreement. The results show that the numerical full model can well simulate the near-surface wave-enhanced layer and suggest that the vertical diffusive coefficients are highly empirical and related to the TKE diffusion, the shear production and the dissipation. Analytical solutions of TKE are also derived for near surface layer and in deep water respectively. Near the surface layer, the dissipation rate is assumed to be balanced by the TKE diffusion to obtain the analytical solution; however, the balance between the dissipation and the shear production is applied at the deep layer. The analytical results in various layers are compared with that of the full numerical model, which confirms that the wave-enhanced layer near the surface is a diffusion-dominated region. The influence of the wave energy factor is also examined, which increases the surface TKE flux with the wave development. Under this region, the water behavior transits to satisfy the classic law of the wall. Below the transition depth, the shear production dominantly balances the dissipation. This revised version was published online in August 2006 with corrections to the Cover Date.  相似文献   

13.
Abstract

An experimental study about the effects of initial conditions of soil and geotextile reinforcement on the mechanical behavior of reinforced sand is presented in this paper. A series of direct shear tests are conducted on reconstituted specimens of dry and moist natural sand prepared with different initial water content (w?=?0, 1.5, 3, and 5%) and including the two arrangements of geotextile layers (one and two layers, respectively). Both S41 and PEC55types of non-woven geotextile were used and placed at different heights of the specimens to investigate the effect of geotextile reinforcement on the behavior of sand. Test specimens were prepared at Dr =80% of relative density and were subjected to three different normal stresses of 100, 200, and 300?kPa. The experimental results showed that the deposition mode (wet and dry) and the geotextile reinforcement have significant effects on the behavior of reinforced sand. The increase in shear strength is relatively more significant for specimens prepared with dry deposition mode as compared to those prepared with wet deposition mode and it increases with the number of geotextile layers, this effect becomes less significant for wet specimens. The experimental results also demonstrated that (PEC55) non-woven geotextile shows a better performance than the (S41) of geotextile. These results can be explained by the effective tensile strength property of polyester yarns of the (PEC55) non-woven geotextile that it has led to a significant increase in the shear strength.  相似文献   

14.
非线性波传播的新型数值模拟模型及其实验验证   总被引：3，自引：4，他引：3  
以一种新型的Boussinesq型方程为控制方程组,采用五阶Runge-Kutta-England格式离散时间积分,采用七点差分格式离散空间导数,并通过采用恰当的出流边界条件,从而建立了非线性波传播的新型数值模拟模型.通过对均匀水深水域内波浪传播的数值模拟说明,模型能较好地模拟大水深水域和强非线性波的传播.通过设置不同的入射波参数来进行潜堤地形上波浪传播的物理模型实验,并将数值解与物理模型实验结果进行了比较.  相似文献   

15.
张洪生  冯文静  商辉 《海洋学报》2007,29(5):161-173
以一种新型的含变换速度变量的Boussinesq型方程为控制方程组,采用五阶Runge-Kutta-England格式离散时间积分,采用七点差分格式离散空间导数,并采用恰当的出流边界条件,从而建立了非线性波传播的新型数值模拟模型.对均匀水深水域内波浪传播的数值模拟,说明在引入变换速度后进一步增大了模型的水深适用范围.对潜堤地形上波浪传播的数值模拟说明,在引入变换速度后进一步提高了模型的数值模拟精度.  相似文献   

16.
Abstract

As a part of the environmental impact assessment studies, geotechnical properties of sediments were determined in the Central Indian Basin. The undrained shear strength and index properties of the siliceous sediments were determined on 20 box cores of uniform dimension collected from various locations in five preselected sites. The maximum core length encountered was 41 cm and most of the sediments were siliceous oozes consisting of radiolarian or diatomaceous tests. The shear strength measurements revealed that surface sediments deposited in recent times (0–10 cm) have a shear strength of 0–1 kPa; this value increases with depth, reaching 10 kPa at 40 cm deep. Older sediments have greater strength because of compaction. Water content varies in the wide range of 312–577% and decreases with depth. The clay minerals such as smectite and illite are dominant and show some control over water content. Wet density, specific gravity, and porosity do not indicate any notable variation with depth, thereby indicating a uniform, slow rate of sedimentation. The average porosity of sediments is 90.2%, specific gravity 2.18, and wet bulk density 1.12 g/cm3. Sediments exhibit medium to high plasticity characteristics, with the average plasticity index varying between 105% and 136%. Preliminary studies on postdisturbance samples showed an increase in natural water content and a decrease in undrained shear strength of sediments in the top 10- to 15-cm layer.  相似文献   

17.
Abstract

To achieve the rapid dewatering of dredged sludge, the flocculation–vacuum-preloading method was tested indoors. In this study, the optimal mixing ratio of six flocculants was determined through the settling column test, and then the proposed method was tested. The water drainage and settlement were monitored during the test, while the soil moisture content and shear strength were measured after the test. The results show that all the flocculants had an optimal mixing ratio, and the addition of 0.8% FeCl3 or 0.08% anionic polyacrylamide (APAM) in the sludge can better accelerate solid–liquid separation of the sludge. After the test, the water content in the sludge decreased from 140% to 60%. Compared with general vacuum preloading, the use of the proposed method increased the water drainage by 46.5% and 56.8% and decreased the soil volumes by 60.5% and 82.4% for FeCl3 and APAM, respectively. Moreover, the corresponding shear strength was increased from 10 to 14 and 17?kPa. In addition, the use of APAM increased the solidification rate of heavy metals in the sludge to more than 80%, effectively inhibiting the migration of heavy metals.  相似文献   

18.
The Huanghe River（Yellow River） Delta has a wide distribution of fine-grained soils. Fluvial alluviation, erosion,and wave loads affect the shoal area, resulting complex physical and mechanical properties to sensitive fine-grained soil located at the river-sea boundary. The cone penetration test（CPT） is a convenient and effective in situ testing method which can accurately identify various soil parameters. Studies on undrained shear strength only roughly determine the fine content（FC） without ma...  相似文献   

19.
Abstract

Recent marine forensic investigations have largely unravelled the sequence of events concerning the sinking of the R.M.S. Titanic and its descent through nearly 3800 m of water to the seafloor on the morning of 15 April 1912. In particular, the velocity and attitude of the Titanic's bow section (at present lying upright, reasonably intact, and embedded by ～12 m at the prow) as it hit the bottom are of general interest to marine accident investigators. During the 1998 Titanic Science Expedition, a single sediment sample was retrieved from the seafloor (depth 20–30 cm) near the wreck by the deep water submersible, Nautile. Published geological studies suggest the seafloor in this area has remained largely undisturbed since 1912. Geotechnical analysis of the sediment sample reveals that the impact was probably a substantially undrained event and that the characteristic undrained shear strength of the sediment is ～25kPa within 10–16 m below the seafloor. A simple analytical model was used to calculate the embedment of a cuboid with dimensions and mass of the water-filled bow as a function of impact velocity, impact angle, and the undrained shear strength of the sediment. The results indicate the impossibility of a steep angle of impact and fast velocity. The most likely scenario is an impact velocity of 5–10 m/s at a fairly shallow angle (<40°), which corroborates the results of hydrodynamic investigations.  相似文献   

20.
The three-dimensional numerical model with σ-coordinate transformation in the vertical direction is applied to the simulation of surface water waves and wave-induced laminar boundary layers. Unlike most of the previous investigations that solved the simplified one-dimensional boundary layer equation of motion and neglected the interaction between boundary layer and outside flow, the present model solves the full Navier–Stokes equations (NSE) in the entire domain from bottom to free surface. A non-uniform mesh system is used in the vertical direction to resolve the thin boundary layer. Linear wave, Stokes wave, cnoidal wave and solitary wave are considered. The numerical results are compared to analytical solutions and available experimental data. The numerical results agree favorably to all of the experimental data. It is found that the analytical solutions are accurate for both linear wave and Stokes wave but inadequate for cnoidal wave or solitary wave. The possible reason is that the existing analytical solutions for cnoidal and solitary waves adopt the first-order approximation for free stream velocity and thus overestimate the near bottom velocity. Besides velocity, the present model also provides accurate results for wave-induced bed shear stress.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号