共查询到20条相似文献，搜索用时 71 毫秒
1.
Since the most severe roll motion occurs at resonance (known as synchronous rolling), the best way of reducing it is to increase the damping. The most common means of doing so is by the installation of bilge keels. If more control is required, both anti-roll tanks and fins are used. Tanks have the advantage of being able to function when the ship is not underway. The use of tanks with liquid free surfaces for reducing roll motion of ships is an old idea. Many researchers have studied the design of anti-roll tanks. However, most of the past effort has concentrated on studying the performance of anti-roll tanks in damping the roll motion of the ship. Little attention has been paid to the fluid motion inside the tank itself. Another important issue is the tank tuning. Proper tuning of the anti-roll tank, to match the ship's natural frequency, is very important in reducing the roll motion. This paper concentrates on the most familiar type, which is the U-tube passive tank as a mechanical absorber of roll motion. A detailed study, covering tank damping, mass, location relative to the ship CG, and tuning, is presented. New suggestions and observations are stated concerning tank damping and tuning. 相似文献
2.
We numerically studied the full (six degrees of freedom) motion of a cargo ship without roll stabilizers in rough (sea state 5) conditions for multiple heading angles ranging from 0° (follower seas) to 180° (head seas). We found that the ship exhibits excessive roll motion in quartering (45° off the stern), beam, and head seas. Therefore, roll damping is critical in these conditions. We then investigated the performance of passive and active anti-roll tank (ART) systems and compared their performance in each of the three sea conditions. Each ART consists of three identical tanks, distributed along the centerline of the ship, each of which consists of two vertical ducts connected at the bottom with a horizontal duct. A pump is located at the middle of the horizontal duct of each tank. The pumps are switched on for active ARTs but switched off for passive ones. The loads (forces and moments) exerted on the ship by the ARTs are added to the hydrodynamic loads (e.g., due to pressure and viscous effects) and the thrust in the governing equations of motion of the ship. Whereas both passive and active ARTs are able to reduce the excessive roll motion, active ARTs outperform the passive ones from three perspectives. First, they are more effective in reducing the roll motion. Second, they require much less working liquid. Third, their performance is insensitive to their natural frequencies and, hence, to their geometric design. In addition, we found that head seas are most responsive to ARTs, which suggests that they are effective in mitigating parametric roll. 相似文献
3.
In this paper our previously developed advanced system identification technique [1] has been applied to extract the frequency dependent roll damping from a series of model tests run in irregular (random) waves. It is shown that this methodology accurately models the roll damping which can then be used to produce accurate predictions of the ships roll motion. These roll motion predictions are not only more accurate than the potential flow predictions but more accurate than potential flow models corrected using either empirical prediction methods [2] and even those corrected using roll damping obtained from free decay sallying experiments. This methodology has the potential to significantly improve roll motion prediction during full scale at sea trails of vessels in order to dramatically improve safety of critical operations such as helicopter landing or ship to ship cargo transfer. 相似文献
4.
M. Taylan 《Ocean Engineering》2000,27(9):1159
Many researchers have studied a wide range of nonlinear equations of motion describing a ship rolling in waves. In this study, a form of nonlinear equation governing the motion of a rolling ship subjected to synchronous beam waves is suggested and solved by the generalized Duffing's method in the frequency domain. Various representations of damping and restoring terms found in the literature are investigated and their solutions are analyzed by the above-mentioned method. Comparative results of nonlinear roll responses are obtained for four distinct vessel types at resonance conditions which constitute the worst situation. The results indicate the importance of roll damping and restoring, when constructing a nonlinear roll model. An inappropriate selection of damping and restoring terms may lead to serious discrepancies with reality, especially in peak roll amplitudes. 相似文献
5.
The large roll motion of ships sailing in the seaway is undesirable because it may lead to the seasickness of crew and unsafety of vessels and cargoes, thus it needs to be reduced. The aim of this study is to design a rudder roll stabilization system based on Radial Basis Function Neural Network (RBFNN) control algorithm for ship advancing in the seaway only through rudder actions. In the proposed stabilization system, the course keeping controller and the roll damping controller were accomplished by utilizing modified Unscented Kalman Filter (UKF) training algorithm, and implemented in parallel to maintain the orientation and reduce roll motion simultaneously. The nonlinear mathematical model, which includes manoeuvring characteristics and wave disturbances, was adopted to analyse ship’s responses. Various sailing states and the external wave disturbances were considered to validate the performance and robustness of the proposed roll stabilizer. The results indicate that the designed control system performs better than the Back Propagation (BP) neural networks based control system and conventional Proportional-Derivative (PD) based control system in terms of reducing roll motion for ship in waves. 相似文献
6.
This study investigates the coupling effects of six degrees of freedom in ship motion with fluid oscillation inside a three-dimensional rectangular container using a novel time domain simulation scheme. During the time marching, the tank-sloshing algorithm is coupled with the vessel-motion algorithm so that the influence of tank sloshing on vessel motions and vice versa can be assessed. Several factors influencing the dynamic behavior of tank–liquid system due to moving ship are also investigated. These factors include container parameters, environmental settings such as the significant wave height, current velocity as well as the direction of wind, wave and flow current acting on the ship. The nonlinear sloshing is studied using a finite element model whereas nonlinear ship motion is simulated using a hybrid marine control system. Computed roll response is compared with the existing results, showing fair agreement. Although the two hull forms and the sea states are not identical, the numerical result shows the same trend of the roll motion when the anti-rolling tanks are considered. Thus, the numerical approach presented in this paper is expected to be very useful and realistic in evaluating the coupling effects of nonlinear sloshing and 6-DOF ship motion. 相似文献
7.
The paper studies the parametric stochastic roll motion in the random waves. The differential equation of the ship parametric roll under random wave is established with considering the nonlinear damping and ship speed. Random sea surface is treated as a narrow-band stochastic process, and the stochastic parametric excitation is studied based on the effective wave theory. The nonlinear restored arm function obtained from the numerical simulation is expressed as the approximate analytic function. By using the stochastic averaging method, the differential equation of motion is transformed into Ito's stochastic differential equation. The steady-state probability density function of roll motion is obtained, and the results are validated with the numerical simulation and model test. 相似文献
8.
The prediction of ship stability during the early stages of design is very important from the point of vessel’s safety. Out of the six motions of a ship, the critical motion leading to capsize of a vessel is the rolling motion. In the present study, particular attention is paid to the performance of a ship in beam sea. The linear ship response in waves is evaluated using strip theory. Critical condition in the rolling motion of a ship is when it is subjected to synchronous beam waves. In this paper, a nonlinear approach has been tried to predict the roll response of a vessel. Various representations of damping and restoring terms found in the literature are investigated. A parametric investigation is undertaken to identify the effect of a number of key parameters like wave amplitude, wave frequency, metacentric height, etc. 相似文献
9.
For a large floating structure in waves, the damping is computed by the linear diffraction/radiation theory. For most degrees of freedom, this radiation damping is adequate for an accurate prediction of the rigid body motions of the structure at the wave frequencies. This is not particularly true for the roll motion of a long floating structure. For ships, barges and similar long offshore structures, the roll damping is highly nonlinear. In these cases the radiation damping is generally quite small compared to the total damping in the system. Moreover, the dynamic amplification in roll may be large for such structures since the roll natural period generally falls within the frequency range of a typical wave energy spectrum experienced by them. Therefore, it is of utmost importance that a good estimate of the roll damping is made for such structures. The actual prediction of roll damping is a difficult analytical task. The nonlinear components of roll damping are determined from model and full scale experiments. This paper examines the roll damping components and their empirical contributions. These empirical expressions should help the designer of such floating structures. The numerical values of roll damping components of typical ships and barges in waves and current (or forward speed) are presented. 相似文献
10.
Thomas W. TreakleIII Dean T. Mook Stergios I. Liapis Ali H. Nayfeh 《Ocean Engineering》2000,27(12):1171
A method to evaluate the use of actively controlled moving weights on board ships to reduce roll motion is developed. The weights can simulate in principle anti-roll-tank systems, or they can be considered a possible anti-roll device in their own right. The ship, the moving weight, and the control device are considered components of a single dynamic system. The full eight-degree-of-freedom set of coupled governing equations for the complete dynamic system is derived. And a three-degree-of-freedom non-linear approximation for the roll motion only (MOTSIM) is derived from these eight equations. The reduced set of equations is used to determine the influence of various parameters and to evaluate control strategies. A PID controller is developed to command the position of the weight and a servomechanism model is used to predict its actual position. Then, the moving-weight system is incorporated into LAMP (Large–Amplitude–Motion Program), a computer code that integrates the governing equations of the sea and the motion of the ship interactively and simultaneously and predicts the motion of the ship in the time domain. A comparison of the results from the two simulations shows that there is fairly good correlation between the simple and complex models, but the simple model is a little optimistic in predicting the effectiveness of the moving-weight system. The results predict that the moving-weight system can be an excellent roll-suppressing device when the moving weight is as small as 1% of the displacement of the ship and the maximum distance the weight moves is as small as 15% of the half-beam. 相似文献
11.
The present paper describes a mathematical model in which the fluid motion inside a U-tank is nonlinearly coupled to the heave, roll and pitch motions of the ship. The main purpose of the investigation is centred on the control of roll motion in the case of parametric resonance in longitudinal waves. A transom stern small vessel, known to be quite prone to parametric amplification, is employed in the study. Four tank designs are employed in order to study the influence of tank mass, tank natural frequency and tank internal damping on the control of parametric rolling at different head seas conditions. Additionally, the influence of the vertical position of the tank is also investigated. The main results are presented in the form of limits of stability, with encounter frequency and wave amplitudes as parameters. Distinct dynamical characteristics are discussed and conclusions are drawn on the relevant parameters for the efficient control of the roll amplifications in head seas. 相似文献
12.
This paper has shown a numerical motion simulation method which can be employed to study on parametric rolling of ships in a seaway. The method takes account of the main nonlinear terms in the rolling equation which stabilize parametric rolling, including the nonlinear shape of the righting arm curve, nonlinear damping and cross coupling among all 6 degrees of freedom. For the heave, pitch, sway and yaw motions, the method uses response amplitude operators determined by means of the strip method, whereas the roll and surge motions of the ship are simulated, using nonlinear motion equations coupled with the other 4 degrees of freedom. For computing righting arms in seaways, Grim's effective wave concept is used. Using these transfer functions of effective wave together with the heave and pitch transfer functions, the mean ship immersion, its trim and the effective regular wave height are computed for every time step during the simulation. The righting arm is interpolated from tables, computed before starting the simulation, depending on these three quantities and the heel angle. The nonlinear damping moment and the effect of bilge keels are also taken into account. The numerical simulation tool has shown to be able to model the basic mechanism of parametric rolling motions. Some main characteristics of parametric rolling of ships in a seaway can be good reproduced by means of the method. Comprehensive parametric analyses on parametric rolling amplitude in regular waves have been carried out, with that the complicated parametric rolling phenomena can be understood better. 相似文献
13.
14.
M. Taylan 《Ocean Engineering》1999,26(11):255
Mathematical modeling of the nonlinear roll motion of ships is one subject widely dealt with in nonlinear ship dynamics. This paper investigates setting up a form of nonlinear roll motion model and developing its periodic solution by the generalized Krylov–Bogoliubov asymptotic method in the time domain. In this model, nonlinearities are introduced through damping and restoring terms. The restoring term is approximated as a third-order odd polynomial whereas the quadratic term is favored to represent the nonlinear damping. The ship is assumed to be under the influence of a sinusoidal exciting force. Although the method is expressible to contain any order of the perturbing term, a single degree is chosen to avoid cumbersome mathematical complexity. In order to improve the solution a first-order correction term is also included. Moreover, a numerical example is carried out for a small vessel in order to validate the solution scheme. 相似文献
15.
随着船舶大型化和港口建设深水化发展,外海不同周期波浪作用下大型系泊船泊稳问题与小型系泊船相比出现了新的特点。为此,利用数值模型方法研究了在不同入射角度和周期的涌浪作用下港内大型系泊船的水动力响应,针对系泊船的泊稳情况探讨了船舶的运动规律和运动特性。研究发现,在涌浪周期较大的情况下,限定波高的泊稳标准不足以用来确定系泊船的正常作业条件,港内泊船的水平运动（纵荡、横荡和艏摇）极易超出运动标准值并影响装卸作业效率,并且船舶的水平运动表现出主要由次重力波主导的低频运动特性,而垂直运动（垂荡、横摇和纵摇）表现出主要由短波主导的波频运动特性。 相似文献
16.
This study considers the coupling effects of ship motion and sloshing. The linear ship motion is solved using an impulse-response-function (IRF) method, while the nonlinear sloshing flow is simulated using a finite-difference method. The IRF method requires the frequency-domain solution prior to conversion to time domain, but the computational effort is much less than that of direct time-domain approaches. The developed scheme is verified by comparing the motion RAOs between the frequency-domain solution and the solution obtained by the IRF method. Furthermore, a soft-spring concept and linear roll damping are implemented to predict more realistic motions of surge, sway, yaw, and roll. For the simulation of sloshing flow in liquid tanks, a physics-based numerical approach adopted by Kim [2001. Numerical simulation of sloshing flows with impact load. Applied Ocean Research 23, 53–62] and Kim et al. [2004. Numerical study on slosh-induced impact pressures on three-dimensional prismatic tanks. Applied Ocean Research 26, 213–226] is applied. In particular, the present method focuses on the simulation of the global motion of sloshing flow, ignoring some local phenomena. The sloshing-induced forces and moments are added to wave-excitation forces and moments, and then the corresponding body motion is obtained. The developed schemes are applied for two problems: the sway motion of a box-type barge with rectangular tanks and the roll motion of a modified S175 hull with rectangular anti-rolling tank. Motion RAOs are compared with existing results, showing fair agreement. It is found that the nonlinearity of sloshing flow is very important in coupling analysis. Due to the nonlinearity of sloshing flow, ship motion shows a strong sensitivity to wave slope. 相似文献
17.
This paper reviews the development of ship anti-roll tanks from the 1880s to the present day including their modelling and control strategies. Mention is also made of other ship roll stabilization systems and the application of the technology to stabilization of other structures. The potential for the use of roll stabilization tanks on modern, high speed multi-hull craft which also have a low speed operational requirement is also discussed. 相似文献
18.
This paper presents two novel nonlinear models of u-shaped anti-roll tanks for ships, and their linearizations. In addition, a third simplified nonlinear model is presented. The models are derived using Lagrangian mechanics. This formulation not only simplifies the modeling process, but also allows one to obtain models that satisfy energy-related physical properties. The proposed nonlinear models and their linearizations are validated using model-scale experimental data. Unlike other models in the literature, the nonlinear models in this paper are valid for large roll amplitudes. Even at moderate roll angles, the nonlinear models have three orders of magnitude lower mean square error relative to experimental data than the linear models. 相似文献
19.
In this paper, we present a mathematical model including seakeeping and maneuvering characteristics to analyze the roll reduction for a ship traveling with the stabilizer fin in random waves. The self-tuning PID controller based on the neural network theory is applied to adjust optimal stabilizer fin angles to reduce the ship roll motion in waves. Two multilayer neural networks, including the system identification neural network (NN1) and the parameter self-tuning neural network (NN2), are adopted in the study. The present control technique can save the time for searching the optimal PID gains in any sea states. The simulation results show that the present developed self-tuning PID control scheme based on the neural network theory is indeed quite practical and sufficient for the ship roll reduction in the realistic sea. 相似文献
20.
Real sea conditions are characterized by multidirectional sea waves. However, the prediction of hull load responses in oblique waves is a difficult problem due to numeral divergence. This paper focuses on the investigation of numerical and experimental methods of load responses of ultra-large vessels in oblique regular waves. A three dimensional nonlinear hydroelastic method is proposed. In order to numerically solve the divergence problem of time-domain motion equations in oblique waves, a proportional, integral and derivative (PID) autopilot model is applied. A tank model measurement methodology is used to conduct experiments for hydroelastic responses of a large container ship in oblique regular waves. To implement the tests, a segmented ship model and oblique wave testing system are designed and assembled. Then a series of tests corresponding to various wave headings are carried out to investigate the vibrational characteristics of the model. Finally, time-domain numerical simulations of the ship are carried out. The numerical analysis results by the presented method show good agreement with experimental results. 相似文献