共查询到20条相似文献，搜索用时 78 毫秒
1.
遥感影像中海洋锋具有弱边缘(Weak Edge)信息特性,其空间尺度在不同的空间位置存在较大的差异。针对传统边缘算子只能提取某一尺度的海洋锋信息,而损失其他尺度信息不足,本文利用小波多尺度分析特性,探讨了海洋锋信息在各尺度间的分布的继承性,提出最佳尺度确定的算法框架,设计出最佳尺度确定算法的流程,进一步进行海洋锋各尺度信息的提取。最后以海面温度锋-墨西哥湾流为实例进行形态特征提取,并与典型的边缘提取算子效果在信息量、抗干扰性、定位精度、连续性和对比度上进行对比分析。试验结果表明了该算法在提取多尺度的海洋锋信息上的可行性和实用性。 相似文献
2.
基于海洋锋空间位置、水平分布结构和垂直扩展特征等时空特征参数,结合海洋锋空间结构几何模型,建立了区域海洋锋温盐三维结构快速重构特征模型,对黄海西部沿岸锋和东海黑潮中段锋锋区温度场进行了仿真计算,并与实测数据进行了比较分析,实验结果表明：仿真结果与实测数据符合较好,实验结果验证了特征模型的有效性和可推广性。海洋锋区声速具有明显的水平梯度变化,对声纳的水下探测和反探测产生显著影响,因此,需要建立实时估计获取锋区水下温、盐结构的方法。海洋锋特征模型能够快速有效地重构海洋锋区温度场,为实时获取海洋锋水下结构特征提供了方法。 相似文献
3.
本文利用1987年1-2月中国第三次南极考察期间在南设得兰群岛邻近海域获得的STD资料,详细阐述了群岛以北海域中的一条海洋峰——大陆水边界(CWB)在表层、次表层和深层的表观特征,并给出了测区表面的地转流分布,计算了斜压变形半径Rbc.作者认为这里沿锋向海流处于地转平衡状态,且锋主要由边界流的作用所致.CWB的沿锋尺度约360km,平均宽度约30km. 相似文献
4.
海洋锋是重要的中尺度海洋现象,具有数据量小、目标小、弱边缘等特性。针对实际检测任务中弱边缘、小目标海洋锋的检测精度低、错检及漏检率高等问题,融合scSE (spatial and channel Squeeze&Excitation)空间注意力模块构建了一种改进的Mask R-CNN海洋锋检测模型。该方法首先对Mask R-CNN骨干网络结构进行改进,采用scSE模块引导的ResNet-50网络作为特征提取网络,通过加权策略对图像通道和空间位置进行特征突出,提升网络对重要特征的提取能力;其次,针对海洋锋目标边缘定位不准确的问题,引入IoU boundary loss构建新的Mask损失函数,提高边界检测精度。最后,为验证方法的有效性,从训练数据和实验模型上,分别设计多组对比实验。实验结果表明,相比传统Mask R-CNN、YOLOv3神经网络及现有Mask R-CNN改进网络,本文方法对SST梯度影像数据集上的强、弱海洋锋检测效果最好,定位准确率（IoU,Intersection-over-union））及检测精度（mAP,Mean Average Precision）均达0.... 相似文献
5.
《中国海洋大学学报(自然科学版)》1989,(Z1)
海洋锋是一种海洋学特征。作者根据1960—1981年的资料,用温、盐指标依聚类方法分析研究了该海区的环流结构和水团的混合带,最后定出了海洋锋的位置。本文还描述了春季黄海中的海洋锋的分布及特征,及其与鹰爪虾、鲅鱼、鲐鱼洄游规律和渔场的关系。 相似文献
6.
7.
本文利用近十年来获得的ＮＯＡＡ卫星红外影像，较为系统地分析了东海海洋锋（黑潮锋、对马暖流锋和浙江沿岸锋）的波动谱特征以及形态的演变。同时还利用浮标测流结果分析了锋面波动中的流态。分析结果表明：东海黑潮锋通常存在４～５个折叠波形，其波长平均约２００ｋｍ，波动随黑潮流向东北方向传播，速度约１６ｃｍ／ｓ。浙江沿岸锋的波动多呈锯齿形，其波长较短，波数多。在浙江沿岸锋波动发展过程中，其波长从开始的２０～４０ｋｍ发展成３０～６０ｋｍ，它们约以１８ｃｍ／ｓ的速度向东北方向传播。东海海洋锋波动演变形态复杂，其中黑潮锋的波动可能演变成锋面涡旋、暖丝和暖环。 相似文献
8.
不同海洋动力过程之间的相互作用决定了海洋系统内部的结构,外观表征上则反映了海洋动力要素的空间及剖面精细化分布与演变特征,海洋动力系统相互作用理论愈来愈成为支撑海洋耦合数值模式与数值预报发展的重要基础.不同于Reynolds尺度平均概念,基于局域平稳均匀统计意义下的集合平均可易于实现集合层级和系统划分.在此基础上提出了一... 相似文献
9.
基于WOA东北亚海1/10°温盐统计数据产品、海洋水文图集和历史海洋调查相关研究成果,系统研究了东北亚海温度盐度结构主要特征;春季和夏季,黄海东西沿岸存在温度低值中心;描述和定义了黑潮右侧次表层伸向西南方向的"黑潮逆流冷舌";研究了东北亚海主要流系和部分海洋中尺度现象(海洋涡旋、海洋锋、上升流、长江冲淡水等)引起的温度盐度结构特征。日本海40°N附近海洋温度锋一年四季都比较强,中国东海海面温度锋在冬季和春季比较强。台湾东北冷涡和日本以南超级暖涡附近是温度极值中心。该研究成果为东北亚海海洋水文环境保障提供技术支撑。 相似文献
10.
《中国海洋大学学报(自然科学版)》2021,51(9)
基于ERA5再分析资料和卫星观测资料,本文揭示了2010年3月9—11日一次层积云发展-消亡过程中东海黑潮海洋温度锋对其的影响机制。研究发现,在层积云的发展阶段,海洋锋通过垂直混合机制影响层积云;而在维持阶段,海洋锋通过气压调整机制影响层积云;在消亡阶段,海洋锋对云的影响较弱。进一步研究表明,海洋锋能影响层积云的垂直结构,在维持阶段层积云的云底/顶高度在冷(暖)洋面下降(抬升),这对应于海洋锋强迫出的下沉(上升)气流。该结果说明东海黑潮海洋锋对大气行星边界层和层积云的垂直结构具有不可忽视的影响。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
13.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
14.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
15.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
16.
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
Oedometer tests have been carried out on 70 undisturbed surficial clays (at approximately 250 mm below the mudline), mostly collected by free-fall corers from sites widely scattered throughout the deep-sea North Atlantic. Acoustic measurements were also made, initially on contiguous samples and ultimately on the same sample using a geophysically instrumented oedometer which also collected electrical resistivity data. Apart from those quiescent areas below the carbonate compensation depth, such as north of the West Indies where very fine clays exist, most of the samples are silty clays whose geotechnical-geophysical properties are dependent on the type of clay minerals present (and their ability to take in moisture), the sand-size fraction, and the quantity of carbonate present. Thus the pure clays have high compressibilities which decrease on the addition of coarse particles, while the converse is true for the acoustic parameters, these increasing with the sand fraction. Using the notion of the intrinsic compression line for all samples, and comparison to it of the measured compression curves, it is clear that, contrary to some previously held ideas, most deep-sea clays are normally consolidated; the addition of carbonate has the effect of creating an open, stronger sediment skeleton. Interestingly, where information is available, the variation with depth of a sample's acoustic velocity follows the void ratio pressure relationship of the compression curve. This allows the construction of an in-situ sediment compression curve using the in-situ geophysical observations. 相似文献
19.
20.
Phylogenetic diversity and phenotypic characterization of cultivable bacterioplankton isolated from polar oceans 总被引：1，自引：0，他引：1
A set of 27 marine planktonic bacteria isolated from the polar regions was characterized by 16S rDNA sequencing and physiological and biochemical testing. More than half of these bacteria were positive for caseinase, gelatinase and 13-glucosidase, and could utilize glucose, maltose or malic acid as carbon source for cell growth. Twelve isolates expressed nitrate reduction activities. Except for one antarctic isolate BSwlO175 belonging to Actinobacteria phylum, these isolates were classified as γ-Proteobacteria, suggesting that γ-Proteobacteria dominated in cultivable marine bacterioplankton at both poles. Genus Pseudoalteromonas was the predominant group in the Chukchi Sea and the Bering Sea, and genus ShewaneUa dominated in cultivable bacterioplankton in the Prydz Bay. With sequence similarities above 97%, genus Psychrobacter was found at both poles. These 27 isolates were psychrotolerant, and significant 16S rDNA sequence similarities were found not only between arctic and antarctic marine bacteria （ 〉 99% ）, but also between polar marine bacteria and bacteria from other aquatic environments （ ≥ 98.8% ）, including temperate ocean, deep sea, pond and lake, suggesting that in the polar oceans less temperature-sensitive bacteria may be cosmopolitan and have a bipolar, even global, distribution at the species level. 相似文献