共查询到20条相似文献，搜索用时 24 毫秒
1.
Design parameters for single- and multiple-tuned liquid column dampers for reducing the response of structures to seismic excitations are presented. A deterministic analysis is carried out using 72 earthquake ground motion records to determine the tuning ratio, tube width to liquid length ratio, and head loss coefficient corresponding to a given mass ratio for single-tuned liquid column dampers. A similar analysis is performed to determine the central tuning ratio, tuning bandwidth, and grouping of dampers for multiple-tuned liquid column dampers. The study indicates that by properly selecting the design parameters, single- and multiple-tuned liquid column dampers can reduce the response of structures to seismic excitation by up to 45 per cent. Design examples using single- and multiple-tuned liquid column dampers in a bridge and a ten-storey building are presented to illustrate how the parameters are selected and to demonstrate the performance of the devices under different ground excitations. The response of several structures with tuned liquid column dampers is compared with that using tuned mass dampers where it is shown that both devices result in comparable reductions in the response. © 1998 John Wiley & Sons, Ltd. This paper was produced under the auspices of the U.S. Government and it is therefore not subject to copyright in the U.S. 相似文献
2.
Lifecycle cost optimization of tuned mass dampers for the seismic improvement of inelastic structures 
下载免费PDF全文
下载免费PDF全文 Emiliano Matta 《地震工程与结构动力学》2018,47(3):714-737
The seismic performance of tuned mass dampers (TMDs) on structures undergoing inelastic deformations may largely depend on the ground motion intensity. By estimating the impact of each seismic intensity on the overall cost of future seismic damages, lifecycle cost (LCC) proves a rational metric for evaluating the benefits of TMDs on inelastic structures. However, no incorporation of this metric into an optimization framework is reported yet. This paper presents a methodology for the LCC‐optimal design of TMDs on inelastic structures, which minimizes the total seismic LCC of the combined building‐TMD system. Its distinctive features are the assumption of a mass‐proportional TMD cost model, the adoption of an iterative suboptimization procedure, and the initialization of the TMD frequency and damping ratios according to a conventional linear TMD design technique. The methodology is applied to the seismic improvement of the SAC‐LA benchmark buildings, taken as representative of standard steel moment‐resisting frame office buildings in LA, California. Results show that, despite their limited performance at the highest intensity levels, LCC‐optimal TMDs considerably reduce the total LCC, to an extent that depends on both the building vulnerability and the TMD unit cost. They systematically present large mass ratios (around 10%) and frequency and damping ratios close to their respective linearly designed optima. Simulations reveal the effectiveness of the proposed design methodology and the importance of adopting a nonlinear model to correctly evaluate the cost‐effectiveness of TMDs on ordinary structures in highly seismic areas. 相似文献
3.
Porcelain electrical equipment (PEE), such as current transformers, is critical to power supply systems, but its seismic performance during past earthquakes has not been satisfactory. This paper studies the seismic performance of two typical types of PEE and proposes a damping method for PEE based on multiple tuned mass dampers (MTMD). An MTMD damping device involving three mass units, named a triple tuned mass damper (TTMD), is designed and manufactured. Through shake table tests and finite element analysis, the dynamic characteristics of the PEE are studied and the effectiveness of the MTMD damping method is verified. The adverse influence of MTMD redundant mass to damping efficiency is studied and relevant equations are derived. MTMD robustness is verified through adjusting TTMD control frequencies. The damping effectiveness of TTMD, when the peak ground acceleration far exceeds the design value, is studied. Both shake table tests and finite element analysis indicate that MTMD is effective and robust in attenuating PEE seismic responses. TTMD remains effective when the PGA far exceeds the design value and when control deviations are considered. 相似文献
4.
This paper presents a study on the behaviour of rectangular liquid dampers under a horizontal excitation of arbitrary time history. The theoretical model to predict motion of a shallow liquid in a rectangular tank is adapted from a previous researchers' model which was developed for sinusoidal excitations. The model includes an energy dissipation term arising from liquid viscosity. In the present consideration of arbitrary excitations, the energy dissipation term is derived in a straightforward way, without resorting to the equivalent linearization method or assumption of harmonic response as used by earlier researchers. The up-crossing rate of wave height is used in furnishing the Reynolds number required for the evaluation of shear stress in the boundary layer. Since there was no known precedent study involving arbitrary excitations, experiments have been performed accordingly to verify the model. Generally, the theoretical model furnishes results which are found to be in close agreement with the experimental ones. The results also illustrate the strong dependency of liquid motion upon the natural frequency of the damper, amplitude and frequency content of the excitation spectrum. The model is then applied to study the effectiveness of tuned liquid dampers in vibration control of a single-degree-of-freedom structure subjected to earthquake excitations. Significant suppression of structural vibration can be achieved using tuned liquid dampers. 相似文献
5.
Viscoelastic dampers (VEDs) are one of the most common passive control devices used in new and retrofit building projects which reduce the structure responses and dissipate seismic energy during an earthquake. Various methods to design this kind of dampers have been proposed based on the desired level of additional damping, eigenvalue assignment, modal strain energy, linear quadratic regulator control theories, and other approaches. In the current engineering practice, the popular method is the one based on the modal strain energy that uses the inter-story lateral stiffness as one of the main variables for damper design. However, depending on the configuration of the structure, in some cases the resulting interstory lateral stiffness can be very large. Consequently, the dampers size would also be large producing much more damping than that effectively necessary, resulting in an increase of the overall cost of the supplemental damping system and causing excessive stress on the structural elements connected to the dampers. In this paper an alternative practical design method for structures with VEDs is proposed. This method uses the inter-story shear forces as one of the main variables to accomplish the damper design compared to what was done in previous studies. Nonlinear time-history analyses were conducted on a 7-story reinforced concrete (RC) structure to check the reliability and effectiveness of the proposed method. Comparisons on the seismic performance between the structure without dampers and that equipped with VEDs were carried out. It is concluded that the proposed method results in a very suitable size of dampers, which are able to improve the performance of the structure at all levels of earthquake ground motions and satisfying the drift requirement prescribed in the codes. 相似文献
6.
Domenico Altieri Enrico Tubaldi Marco De Angelis Edoardo Patelli Andrea Dall’Asta 《Bulletin of Earthquake Engineering》2018,16(2):963-982
Viscous dampers are widely employed for enhancing the seismic performance of structural systems, and their design is often carried out using simplified approaches to account for the uncertainty in the seismic input. This paper introduces a novel and rigorous approach that allows to explicitly consider the variability of the intensity and characteristics of the seismic input in designing the optimal viscous constant and velocity exponent of the dampers based on performance-based criteria. The optimal solution permits controlling the probability of structural failure, while minimizing the damper cost, related to the sum of the damper forces. The solution to the optimization problem is efficiently sought via the constrained optimization by linear approximation (COBYLA) method, while Subset simulation together with auxiliary response method are employed for the performance assessment at each iteration of the optimization process. A 3-storey steel moment-resisting building frame is considered to illustrate the application of the proposed design methodology and to evaluate and compare the performances that can be achieved with different damper nonlinearity levels. Comparisons are also made with the results obtained by applying simplifying approaches, often employed in design practice, as those aiming to minimize the sum of the viscous damping constant and/or considering a single hazard level for the performance assessment. 相似文献
7.
Tuned mass dampers for response control of torsional buildings 总被引：1，自引：0，他引：1
This paper presents an approach for optimum design of tuned mass dampers for response control of torsional building systems subjected to bi‐directional seismic inputs. Four dampers with fourteen distinct design parameters, installed in pairs along two orthogonal directions, are optimally designed. A genetic algorithm is used to search for the optimum parameter values for the four dampers. This approach is quite versatile as it can be used with different design criteria and definitions of seismic inputs. It usually provides a globally optimum solution. Several optimal design criteria, expressed in terms of performance functions that depend on the structural response, are used. Several sets of numerical results for a torsional system excited by random and response spectrum models of seismic inputs are presented to show the effectiveness of the optimum designs in reducing the system response. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
8.
本文提出了一种新的控制策略——多重双重调谐质量阻尼器(以下简称为MDTMD)。MDTMD系统参数的可能组合形成十种MDTMD模型,本文评价其中最易制作的一种MDTMD模型。利用定义的优化目标函数,评价了MDTMD的控制性能。数值结果表明MDTMD比双重调谐质量阻尼器(DTMD)具有更好的有效性和对频率调谐的鲁棒性。但MDTMD的冲程大于DTMD的冲程。 相似文献
9.
李春祥 《地震工程与工程振动》2005,25(4):155-161
提出了适用于控制大跨桥梁风致振动的杠杆式主动多重调谐质量阻尼器（LT-AMTMD）控制策略.利用建立的LT-AMTMD结构系统的动力放大系数,评价了LT-AMTMD的性能.数值结果表明,驱动器置于质量块处的LT-AMTMD比驱动器置于其它位置的LT-AMTMD更加有效.驱动器置于质量块处的LT-AMTMD可以根据实际需要,通过改变支撑位置来调节弹簧的静伸长,而且保持其性能不变（包括冲程）.数值结果还表明,驱动器置于质量块处的LT-AMTMD可以明显地提高LT-MTMD的性能,而且比单个杠杆式主动调谐质量阻尼器（LT-ATMD）更加有效. 相似文献
10.
使用Kanai-Tajimi地震动模型,建立了主动调谐质量阻尼器(ATMD)结构系统的传递函数。将ATMD最优参数的评价准则定义为：设置ATMD结构均方根位移(解析式)的最小值的最小化。将ATMD有效性的评价准则定义为：设置ATMD结构均方根位移的最小值的最小化与未设置ATMD结构的均方根位移之比。根据逃择的评价准则,评价了地震卓越频率系数(EDFR)对ATMD抗震控制性能的影响。同时也评价了EDFR对被动调谐质量阻尼器(PTMD)抗震控制性能的影响。 相似文献
11.
Buildings are continually subject to dynamic loads, such as wind load, seismic ground motion, and even the load from internal utility machines. The recent trend of constructing more flexible high‐rise buildings underscores the importance of including viscoelastic dampers in building designs. Viscoelastic dampers are used to control the dynamic response of a building. If the seismic design is based only on the linear response spectrum, considerable error may occur when calculating the seismic response of a building; rubber viscoelastic dampers show non‐linear hysteretic damping that is quite different from viscous damping. This study generated a non‐linear response spectrum using a non‐linear oscillator model to simulate a building with viscoelastic dampers installed. The parameters used in the non‐linear damper model were obtained experimentally from dynamic loading tests. The results show that viscoelastic dampers effectively reduce the seismic displacement response of a structure, but transmit more seismic force to the structure, which essentially increases its seismic acceleration response. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
12.
Second‐mode tuned mass dampers in base‐isolated structures for reduction of floor acceleration 下载免费PDF全文
下载免费PDF全文 To reduce floor acceleration of base‐isolated structures under earthquakes, a tuned mass damper (TMD) system installed on the roof is studied. The optimal tuning parameters of the TMD are analyzed for linear base isolation under a generalized ground motion, and the performance of the TMD is validated using a suite of recorded ground motions. The simulation shows that a TMD tuned to the second mode of a base‐isolated structure reduces roof acceleration more effectively than a TMD tuned to the first mode. The reduction ratio, defined as the maximum roof acceleration with the TMD relative to that without the TMD, is approximately 0.9 with the second‐mode TMD. The higher effectiveness of the second‐mode TMD relative to the first‐mode TMD is attributed primarily to the unique characteristics of base isolation, ie, the relatively long first‐mode period and high base damping. The modal acceleration of the second mode is close to or even higher than that of the first mode in base‐isolated structures. The larger TMD mass ratio and lower modal damping ratio of the second‐mode TMD compared to the first‐mode TMD increases its effect on modal acceleration reduction. The reduction ratio with the second‐mode TMD improves to 0.8 for bilinear base isolation. Because of the detuning effect caused by the change in the first‐mode period in bilinear isolation, the first‐mode TMD is ineffective in reducing roof acceleration. Additionally, the displacement experienced by the second‐mode TMD is considerably smaller than that of the first‐mode TMD, thereby reducing the installation space for the TMD. 相似文献
13.
In this study, several mass dampers were designed and fabricated to suppress the seismic responses of a ¼‐scale three‐storey building structure. The dynamic properties of the dampers and structure were identified from free and forced vibration tests. The building structure with or without the dampers was, respectively, tested on a shake table under the white noise excitation, the scaled 1940 El Centro earthquake and the scaled 1952 Taft earthquake. The dampers were placed on the building floors using the sequential procedure developed by the authors in previous studies. Experimental results indicated that the multiple damper system is substantially superior to a single tuned mass damper in mitigating the floor accelerations even though the multiple dampers are sub‐optimal in terms of tuning frequency, damping and placement. These results validated the sequential procedure for placement of the multiple dampers. The structure was also analysed numerically based on the shake table excitation and the identified structure and damper parameters for all test cases. Numerical and experimental results are in good agreement, validating the dynamic properties identified. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
14.
调质阻尼器地震反应控制应用研究 总被引：6，自引：0，他引：6
本文在结构地震反应时程分析基础上,研究调质阻尼器控制地震反应的最优参数设计方法,分析了多自由度体系的阻尼器设计以及调质阻尼器控制的失调效应．并用算例验证了该设计方法用于地震反应控制的可行性。 相似文献
15.
Direct design method based on seismic capacity redundancy for structures with metal yielding dampers 下载免费PDF全文
下载免费PDF全文 In this study, a direct static design method for structures with metal yielding dampers is proposed based on a new design target called the seismic capacity redundancy indicator (SCRI). The proposed method is applicable to the design of elastic‐plastic damped structures by considering the influence of damper on different structural performance indicators separately without the need for iteration or nonlinear dynamic analysis. The SCRI—a quantitative measure of the seismic capacity redundancy—is defined as the ratio of the seismic demand required by the target performance limit to the design seismic demand. Changes in the structural SCRI are correlated with the parameters of the supplemental dampers so that the dampers can be directly designed according to a given target SCRI. The proposed method is illustrated through application to a 12‐story reinforced‐concrete frame, and increment dynamic analysis is performed to verify the effectiveness of the proposed method. The seismic intensity corresponding to the target structural performance limit is regarded as a measure of the structural seismic capacity. The required seismic intensity increases after the structure is equipped with the designed metal yielding dampers according to the expected SCRI. It is concluded that the proposed method is easy to implement and feasible for performance‐based design of metal yielding dampers. 相似文献
16.
Seismic structural control using semi-active tuned mass dampers 总被引：8，自引：1，他引：8
This paper focuses on how to determine the instantaneous damping of the semi-active tuned mass damper (SATMD) with continuously
variable damping. An off-and-towards-equilibrium (OTE) algorithm is employed to examine the control performance of the structure/SATMD
system by considering the damping as an assumptive control action. The damping modification of the SATMD is carried out according
to the proposed OTE algorithm, which is formulated based on analysis of the structural movement under external excitations,
and the measured responses of the structure at every time instant. As examples two numerical simulations of a five-storey
and a ten-storey shear structures with a SATMD on the roof are conducted. The effectiveness on vibration reduction of MDOF
systems subjected to seismic excitations is discussed. Analysis results show that the behavior of the structure with a SATMD
is significantly improved and the feasibility of applying the OTE algorithm to the structural control design of SATMD is also
verified. 相似文献
17.
This paper reports on the results of a study conducted on tanks partially filled with water, representing tuned liquid dampers (TLD), subjected to both 1D and 2D horizontal excitations. The sloshing response of the water in the tank is characterized by the free surface motion, the resulting base shear force, and evaluation of the energy dissipated by the sloshing water. A 1D non‐linear flow model capable of simulating a TLD equipped with damping screens is employed to model a 2D TLD. Application of this particular model requires the assumption that the response is decoupled and can be treated as the summation of two independent 1D TLDs. Results from the non‐linear flow model are compared with the 2D experimental shake table test results leading to a validation of the decoupled response assumption. This attractive decoupled response property allows square and rectangular tanks to be used as 2D TLDs, which can simultaneously reduce the dynamic response of a structure in two perpendicular modes of vibration. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
18.
Numerical studies of existing buildings demonstrate the effectiveness of nonlinear/inelastic rooftop tuned mass damper frames (NRTMDF) used as a retrofit for reducing seismic response. The technique utilizes a rooftop penthouse as a tuned mass damper with mass incorporated as the roof deck of the penthouse while targeted nonlinearity and energy dissipation are introduced through buckling restrained braces (BRBs) linking the penthouse mass to the structure below. The writers summarize numerical studies of ten existing buildings modified with a specifically tuned NRTMDF. The studies demonstrate the effectiveness of the technique that stems from elastic and transient inelastic period shifts enabled by the damper coupled with targeted energy dissipation in the penthouse BRBs. Numerical simulations using response nonlinear time‐history analysis techniques show that for many structures and sites, the NRTMDF decreases peak transient response and overall seismic demand of the original structure. The technique also reduces seismic demand on nonstructural elements and components, manifested as reductions in floor acceleration spectra. Energy methods show that the approach enables significant reductions in energy demand on the original structure through the complete earthquake acceleration history. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
19.
20.
Yutaka Nakamura Akira Fukukita Kazuo Tamura Issei Yamazaki Taichi Matsuoka Kazuhiko Hiramoto Katsuaki Sunakoda 《地震工程与结构动力学》2014,43(4):507-527
This paper presents a new type of electromagnetic damper with rotating inertial mass that has been developed to control the vibrations of structures subjected to earthquakes. The electromagnetic inertial mass damper (EIMD) consists of a ball screw that converts axial oscillation of the rod end into rotational motion of the internal flywheel and an electric generator that is turned by the rotation of the inner rod. The EIMD is able to generate a large inertial force created by the rotating flywheel and a variable damping force developed by the electric generator. Device performance tests of reduced‐scale and full‐scale EIMDs were undertaken to verify the basic characteristics of the damper and the validity of the derived theoretical formulae. Shaking table tests of a three‐story structure with EIMDs and earthquake response analyses of a building with EIMDs were conducted to demonstrate the seismic response control performance of the EIMD. The EIMD is able to reduce story drifts as well as accelerations and surpasses conventional types of dampers in reducing acceleration responses. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献