共查询到20条相似文献，搜索用时 656 毫秒
1.
基于挪威海洋技术研究所 (MARINTEK) 和挪威科技大学 (NTNU) 共同研发的VIVANA模型,编制了一个基于频率响应法的海底悬跨管道涡激振动预报程序,其计算结果与VIVANA符合得较好.应用所编制的程序分析在不同流速条件下海底悬跨管道的涡激振动响应及响应频率的特征,对不同悬跨长度、不同截面特征、具有简单边界的海底悬跨管道涡激振动响应和响应频率进行了计算,给出位移和应力沿管跨的分布及响应频率的变化规律. 相似文献
2.
3.
提出一种海底管道沉降计算方法——递推法，应用到胜利油田埕岛海域海底管道沉降计算中，并将计算结果与目前常用的日本规范法和极限法进行比较。研究发现在粉土与粉质粘土为主的强度较高的海床上，递推法与日本规范法计算结果比较接近，极限法的最小；在淤泥质土组成的强度较低的海床上，日本规范法的计算值最大，递推法的居中，极限法的最小。逆推法可计算裸置和埋设两种形式的管道沉降量，而另外两者只能计算裸置管道的沉降。文中进一步讨论了引起管道沉降的影响因素，土体强度和压缩性对管道沉降影响较大。且管道埋深越大，沉降也越大。最后分析了黄河水下三角洲埕岛海域4个区的管道沉降量，Ⅰ区争Ⅱ区管道沉降较小，可以忽略，Ⅳ区沉降较大，在淤泥质软土上的管道，可能会完全陷入土中。 相似文献
4.
5.
埕岛油田海底管线在位稳定性的计算分析 总被引：1，自引：0，他引：1
埕岛油田主要分布粉土和淤泥质软土2类典型的海床.通过建立海床与其上裸置管线相互作用的有限元计算模型,对埕岛油田2类典型海床上裸置管线的在位稳定性进行了数值计算分析,并与现行常用的DNV(挪威船级社)管道设计方法的计算结果进行了对比.分析表明,对于埕岛油田粉土海床上裸置管线的在位稳定性分析,数值计算结果与DNV简化分析方法的结果较为一致;对于埕岛油田淤泥质软土海床上裸置管线的在位稳定性分析,DNV简化分析得到的裸置管线的在位稳定性一般高于相应的数值计算结果. 相似文献
6.
海底管道是天然气水合物大规模开采和集输的关键装备。天然气水合物的开采过程会扰动沉积层的结构，改变沉积层的强度和力学特性，诱发海床发生不均匀沉降，并对水合物开采区内海底管道的力学特性产生影响，如引起管道发生大变形、悬跨、屈曲、断裂等。基于ABAQUS有限元软件，建立天然气水合物开采区内“海床-管道”耦合作用模型，模拟了天然气水合物开采过程中海床沉降变形及其对管道应力、应变、弯矩、悬跨等力学行为的影响。研究结果表明，在天然气水合物开采过程中，海床的不均匀沉降将引起管道发生显著位移并发生弯曲，管道的应力、应变随着变形的增大而增大。当海床沉降量达到某一程度时，管道将脱离海床，产生悬跨，并引发涡激振动风险。 相似文献
7.
海底滑坡会对海洋工程结构物造成严重破坏。滑移速度和距离是量化和分析海底滑坡的两个重要参数。目前BING等计算方法在模拟水下土体流动方面存在局限性,因此通过建立考虑土体固结和侵蚀效应的控制方程,选用摩擦流变模型,采用SPH深度积分算法,对海底滑坡进行了模拟研究。对比不同水深、坡度、接触摩擦系数和侵蚀率条件下的滑移体的速度、高度、长度的时程曲线,整理了最大滑移距离和速度,讨论变化规律。研究成果可为海底滑坡灾害预警和海底管线路由选址提供技术参考。 相似文献
8.
水下生产系统跨接管结构极限承载能力分析 总被引：1，自引：0，他引：1
跨接管是水下生产系统的主要构件之一,水下地形变化易导致跨接管两端承受较大边界位移载荷,对水下生产系统的结构安全性产生不利影响。研究并分析了端部相对位移载荷作用下跨接管结构的极限承载能力及跨接管失效模式的特点,表明整体轴向压缩位移分量是导致跨接管结构发生极限破坏的主要因素。在此基础上考虑了内表面周向裂纹对跨接管极限强度的影响。分析结果表明:当裂纹较小时,因弯管截面的椭圆化和塑性屈服,轴向压缩位移很容易使跨接管发生整体压缩失效;当裂纹较大时,因为裂纹韧带区的高应力效应,跨接管会在整体压缩失效之前达到极限状态;最终失效模式取决于裂纹的位置及大小。 相似文献
9.
10.
悬跨海底电缆作为细长柔性结构,在静力平衡状态下具有一定的垂度,在水流作用下的涡激振动特性与海底管线和海洋立管等结构也有很大的不同,其振动模态受垂跨比影响很大。通过物理模型试验开展了不同垂跨比下悬跨海缆的涡激振动和疲劳损伤特性研究。试验模型按照水弹性相似准则设计,试验中测量了不同流速下海缆模型产生涡激振动时的应变历时数据,采用模态分析法获得了模型涡激振动时的振动模态和振幅。分析了不同流速下海缆模型的振动模态、应变和疲劳损伤的变化和分布特征。试验结果表明：垂跨比显著影响了海缆的涡激振动模态和应变幅值大小。在本试验流速范围内,对一定长度的悬跨海缆模型,当垂跨比较大时,随着流速的增大,模型涡激振动的主响应振动依次出现反对称1阶和对称1阶模态;当垂跨比较小时,模型涡激振动的主响应模态依次出现反对称1阶和对称2阶模态。当涡激振动主响应模态为反对称1阶时,疲劳损伤最大值达到0. 1~0.7。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
13.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
14.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
15.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
16.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
Shigehisa Nakamura 《Marine Geodesy》2000,23(1):55-61
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone. 相似文献
19.
The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics. 相似文献
20.