共查询到20条相似文献，搜索用时 31 毫秒
1.
2008年汶川发生MS8.0级地震,此次地震触发了大约20万处滑坡,其中大光包滑坡是汶川地震触发的最大规模的滑坡,其复杂的高速远程运动机理引起了国内外学者的广泛关注。本文结合热分解及动态结晶将地震中断层间摩擦弱化机制(闪速加热导致热分解及粉末润滑)运用于大光包滑坡高速远程运动的模拟。本文通过修改非连续变形分析(DDA)程序中强度参数的输入方式,以基于速度变化的强度参数取代原DDA程序中的常数强度参数,进而实现了摩擦系数随接触两侧相对速度变化的动态调整。运用修改后的DDA对大光包滑坡的运动过程进行模拟。模拟结果表明滑床摩擦弱化是导致大光包滑坡高速远程运动特征的重要原因,修改后的DDA由于考虑了滑床摩擦弱化能够更加合理地模拟滑坡的高速远程运动特征,本文模拟的大光包滑坡在地震作用下失稳后,由于滑床摩擦弱化,更多的能量转化为动能,高速滑体掠过黄洞子沟后,爬上对面的平梁子,最终由于平梁子的“急刹车”作用,滑体停止运动。与修改前DDA相比,修改后的DDA对大光包滑坡运动过程和最终堆积形态的模拟结果与已有文献记载和野外调查结果相吻合。这也间接证明了大光包滑坡滑动过程中由于白云岩间摩擦闪速加热导致热分解及粉末润滑造成的摩擦系数降低,可能是造成大光包滑坡高速远程运动的重要原因。 相似文献
2.
An extensive examination of the discontinuous deformation analysis (DDA) in block dynamic sliding modeling is carried out in this paper. Theoretical solutions for a single block sliding on an arbitrarily inclined plane by applying the horizontal/vertical seismic loadings to the sliding block as acceleration time histories or to the base as constraint displacement time histories are derived. As compared with the theoretical solutions, for a single block sliding, the DDA predicts the sliding displacements and block interaction forces accurately under various base incline angles and friction angles under both the harmonic loadings and a real seismic loading. The vertical seismic component may influence the block sliding displacements to different extent, and the DDA can capture these phenomena successfully and give accurate results. For the calculation of the single block relative sliding, both the theoretical and the DDA solutions indicate that applying the seismic accelerations as constraint displacement time histories (derived by integrating the seismic accelerations twice) to the base is equivalent to applying the seismic accelerations as volume forces to the sliding block in the opposite directions. The DDA modeling also demonstrates that this conclusion still stands for the case of multi‐block sliding. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
3.
高温高压及干燥条件下斜长石和辉石断层泥的摩擦滑动研究 总被引：1，自引：0，他引：1
岩石摩擦滑动的力学行为能够很好地用速率和状态依赖性摩擦本构关系来描述。在速率和状态依赖性本构关系中,速度依赖性参数a-b是控制摩擦滑动稳定性的重要参数。且a-b<0是断层上不稳定滑动成核的必要条件。为了进一步研究控制摩擦滑动的矿物成分因素,在已有辉长岩摩擦滑动实验结果的基础上,对辉长岩中主要矿物(斜长石和辉石)在不同加载条件下进行了3个系列的摩擦滑动实验研究。通过对实验结果的分析得到如下结论:(1)斜长石断层泥在实验温度范围内(<617℃)显示速度强化,且在大于450℃的高温区其速度依赖性参数a-b随温度的增大而增加。辉石断层泥的实验显示其有利于速度弱化滑动行为的出现,是造成辉长岩在615℃出现速度弱化的原因。(2)斜长石与辉石断层泥的摩擦强度都没有随温度的增加而显著变化。辉长岩断层泥的摩擦强度(1.83mm滑动位移处的值)为斜长石与辉石断层泥摩擦强度按体积百分比加权的平均值(摩擦系数精确到2位有效数字一致)。这一结果表明,辉长岩断层泥的应力支承结构可以抽象为一种双组分并列单元模型。(3)尽管前人研究结果表明石英控制了花岗岩的摩擦特性,但是某种主要矿物对岩石整体摩擦滑动性质的控制作用并不具有普适性。对于中性岩、基性岩而言,不能以一种主要矿物(如斜长石等)来判断岩石整体的摩擦滑动稳定性,否则会导致错误结论。 相似文献
4.
Fan Jian Tang Jiaxiang Department of Civil Engineering Huazhong University of Science Technology Wuhan 《中国地质大学学报(英文版)》2001,12(4)
lNTRODUCTlONBase iso1ation is regarded as a practical and economicalway to protect structures from damages subjected to earth-quake motion. Isolators implemented between the base raft ofthe structure and foundation can dissipate and absorb earth-quake energy, and reduce obviously the transmission of groundmotion to structure. In short, the principle of base isolation in-cludes two factors: (i) The natural period of structures withfixed base is usually 0. 2-- l. 2 s, close to the natural pe… 相似文献
5.
A series of centrifuge shaking table model tests are conducted on 4?×?4 pile groups in liquefiable ground in this study, achieving horizontal–vertical bidirectional shaking in centrifuge tests on piles for the first time. The dynamic distribution of forces on piles within the pile groups is analysed, showing the internal piles to be subjected to greater bending moment compared with external piles, the mechanism of which is discussed. The roles of superstructure–pile inertial interaction and soil–pile kinematic interaction in the seismic response of the piles within the pile groups are investigated through cross-correlation analysis between pile bending moment, soil displacement, and structure acceleration time histories and by comparing the test results on pile groups with and without superstructures. Soil–pile kinematic interaction is shown to have a dominant effect on the seismic response of pile groups in liquefiable ground. Comparison of the pile response in two tests with and without vertical input ground motion shows that the vertical ground motion does not significantly influence the pile bending moment in liquefiable ground, as the dynamic vertical total stress increment is mainly carried by the excess pore water pressure. The influence of previous liquefaction history during a sequence of seismic events is also analysed, suggesting that liquefaction history could in certain cases lead to an increase in liquefaction susceptibility of sand and also an increase in dynamic forces on the piles. 相似文献
6.
针对常规摩擦阻尼器的起滑力难以确定的问题,提出了复合摩擦阻尼系统（CFDS）,它由非线性硬弹簧和摩擦阻尼器串联而成。当地震较小时,摩擦阻尼器处于附着状态,非线性硬弹簧发挥作用,防止隔震层位移过大;当地震较大时,非线性硬弹簧的变形则保持不变,摩擦阻尼器处于滑动状态,通过摩擦阻尼耗散能量。建立了带有复合摩擦阻尼系统的基础隔震结构的运动方程,指出摩擦阻尼器处于附着和滑移2种状态下边界条件。据此研究了常规强震和近断层脉冲型地震动作用下复合摩擦阻尼装置对橡胶隔震结构的减震效果。仿真分析表明：安装复合摩擦阻尼系统,在显著降低隔震层位移的同时,对上部结构的层间位移和加速度均有一定的减震效果;并且,在整个运动过程中,摩擦阻尼器会在附着和滑移2种状态之间来回切换。详细研究了复合摩擦阻尼系统的３个参数对隔震结构的减震效果。结果表明：在不同地震波作用下,由于摩擦阻尼系统参数的变化导致隔震结构地震响应的变化趋势是不同的,因此最优参数的取值与输入地震波类型和地面加速度峰值有关,并且不存在使隔震层位移和上部结构加速度同时达到最小的最优参数,因此需要设定合适的控制目标以确定适当的阻尼系统参数。 相似文献
7.
液化场地桩-土-桥梁结构地震相互作用简化分析方法 总被引：2，自引：0，他引：2
液化场地桩-土-桥梁结构地震相互作用分析属于桩基桥梁抗震设计中的一个关键科学问题,而目前尚缺乏合理的简化分析方法。鉴于此,直接针对振动台试验,基于Penzien模型,建立了液化场地桩-土-桥梁结构地震相互作用的数值分析模型与相应的简化分析方法。通过振动台试验验证了数值建模途径与简化计算分析方法的正确性,可用于液化场地桩基桥梁结构地震反应的分析,并且特别考虑砂层中孔压升高引起的砂土承载力衰减效应,推荐了计算参数的合理选取方法;据此进行了桩径、桩土初始模量比、砂土内摩擦角、上部桥梁结构质量等重要参数对液化场地桩-土地震相互作用影响的敏感性分析。研究表明：在液化场地条件下,随桩径和桩土初始模量比的增大,桩的峰值加速度、峰值位移减小,而桩的峰值弯矩则增大;随砂土内摩擦角增大,桩的峰值加速度、峰值弯矩、峰值应力均增大,而桩的峰值位移则减小;随上部结构配重增大,桩的峰值位移、峰值弯矩均增大。 相似文献
8.
An original theoretical model has been devised to simulate mass flow over hill slopes due to gravitational sliding. The sliding mass is discretized into a sequence of contiguous blocks which are subjected to gravitational forces, to bottom friction and to surface resistance stresses that are generally negligible for subaerial flows, but are relevant for submarine slides. The blocks interact with each other while sliding down the hill flanks because of internal forces that dissipate mechanical energy and produce a momentum exchange between the individual blocks, yet conserving the total momentum of the mass. Internal forces are expressed in terms of interaction coefficients depending on the instantaneous distance between the block centers of mass, which is a measure of the deformation experienced by the blocks: the functional dependence includes three parameters, namely the interaction intensity ¯, the deformability parameter and the shape parameter , by means of which a wide range of interaction types can be fully accounted for. The time integration is performed numerically by solving the equations for the block velocities and positions at any time ti by means of the block accelerations at the previous time ti-1, and by subsequently updating the block accelerations, which allows to proceed iteratively to the following times. The model has been tested against laboratory results available from literature and by means of several numerical experiments involving a simplified geometry both for the sliding body and the basal surface, with the purpose of clarifying the influence of the model parameters on the slide dynamics. The model improves the performance of the existing kinematic models for slides, moreover preserving an equivalent numerical simplicity. Future applications and possible improvements of this model are suggested. 相似文献
9.
进行岩石摩擦滑动变形演化过程的声发射特征试验研究。以数字散斑相关方法和声发射系统为试验监测手段,采用双面剪切模型试验方法,开展界面摩擦滑动速率与声发射振铃计数、界面摩擦滑动位移与声发射累计能量、试件变形能密度与声发射b值的对应关系研究。结果表明：（1）声发射振铃计数演化受岩石界面摩擦滑动速率影响,界面摩擦滑动速率的突变与声发射振铃计数激增有较好对应关系;（2）界面摩擦滑动位移与摩擦滑动过程中声发射累计能量演化趋势具有较好的对应关系,可以利用声发射累计能量对岩石摩擦滑动位移的变化趋势进行定性判断;（3）通过声发射b值演化分析可以得出,在剪应力缓慢增长阶段,界面摩擦滑动以随机分布的小尺度微破裂为主;在剪应力线性增长阶段后期,界面摩擦滑动以锁固段的大尺度微破裂为主;在剪应力波动增长阶段,岩石摩擦滑动失稳既可能是由小尺度微破裂为主引发的状态转化,又可能是由以锁固段大尺度微破裂为主引发的稳定状态转换。 相似文献
10.
11.
Summary Direct shear tests were conducted on a granite to granite interface for the purpose of tracing the evolution of frictional resistance as the initially smooth and polished surface wears during continuing shearing displacement. At the moment when sliding on the freshly manufactured interface starts (first slip), the friction angle is very low, between 15° and 20°, but then it increases with displacement rapidly without reaching a peak in the first test (maximum displacement less than 25 mm). Upon repeated shearing of the same surface (without re-finishing), this process of displacement-strengthening continues until a total accumulated displacement of about one half of one meter is reached. At this point, the angle of friction would typically be between 42° and 44°.Once the residual surface was established, the effect of time-related parameters, the duration of stationary contact under constant normal and shear load and variable displacement rate, were investigated. The frictional resistance is shown to increase with decreasing displacement rate and to increase with the duration of stationary contact.At a normal load greater than about one half of one MPa, shear displacement on a residual surface proceeds in an unstable, stick-slip manner. The change from stable to unstable sliding, that can be effected by either decreasing the sliding velocity or increasing the normal load, is not instantaneous, but occurs over a finite amount of displacement. 相似文献
12.
危岩体在经历地震和强降雨之后其抗滑力下降,从而导致重力作用失稳,是一种常见的破坏形式。危岩块体的失稳破坏取决于岩体结构面的状况,随着结构面的张开及黏结程度下降,危岩块体会发生失稳而崩塌,基于常规位移监测方法难以达到危岩块体监测预警的目的。而固有振动频率可以有效反映岩体的物理力学参数的变化,进而可以对其安全性做出预判。基于模型试验,在保持下滑力不变的情况下,通过固有振动频率来对滑坡内部的黏结力和摩擦力等力学指标进行分析。通过实际静摩擦力是否达到最大静摩擦力的方法来科学判识岩体的稳定情况。试验结果得出：计算的摩擦力可以有效分析岩体的安全性,并证明固有振动频率在降低至6 Hz以下,岩体开始趋于破坏。同时,得出由于摩擦力破坏后期占据抗滑力的比重逐渐升高,最高达到抗滑力的80%,从而造成破坏末期摩擦力不降反升的情况。基于固有振动频率的监测,可对岩体的损伤做出定量判断,也可评估岩体静摩擦力指标,从而实现扰动后岩体的安全评价。这种基于振动模态的岩体安全监测与损伤评价新的技术思路,将在实际工程中发挥重大作用。 相似文献
13.
断层作用热模型及其对烃源岩热演化的影响 总被引：1，自引：0，他引：1
从盆地的应力状态分析入手,从断层摩擦生热的角度,建立了断层作用生热的定量模型。在此基础上,确定了断层摩擦产生的热量与断层的性质、深度、构造应力和流体压力等之间的定量关系,定量分析了断层摩擦生热对烃源岩热演化的影响。结果表明:断层作用的生热量主要决定于断层的深度,构造应力的大小、流体压力、断层的位移量、断面摩擦系数等;断层的活动速率对断层摩擦的生热量没有影响,但对断层带内产生的温度却起决定性的作用;在断层快速活动的条件下(地震型),断层摩擦生热虽然可以产生很高的温度,可以造成断层面附近岩石的局部熔融,但其影响范围和影响持续的时间是十分有限的。 相似文献
14.
建筑桩基的有效应力地震反应分析：I—计算方法 总被引：2，自引：1，他引：1
根据地震作用、上部结构、桩基的特点,建立了建筑桩基地震反应的计算模型,考虑了桩－土－上部结构的动力相互作用。然后奖饱和土体现为由固、液二相组成的两相介质,基于Ｂｉｏｔ动力固结方程,提出一种建筑桩基地震反应的有效应力动力分析方法,并给出了具有计算步骤。 相似文献
15.
可液化土中地铁结构的地震响应 总被引：14，自引：3，他引：11
在饱和土耦合作用与土和结构相互作用理论基础上,以地铁车站为例,用有限元法研究地下结构在地震液化作用下的响应。所采用的软件为动力两相体非线性有限元软件Dyna-Swandyne-II,该软件可以应用先进的Pastor-Zienkiewicz III广义塑性模型模拟可液化土的动力特性,应用u-p形式的Biot方程,在有限元分析中充分考虑孔隙水与土之间的耦合,同时考虑地下结构与饱和土在动力作用下的非线性相互作用。分析了地铁车站的动力响应,包括地铁内力、加速度以及地铁位移。研究结果表明,地铁结构在地震液化作用下会产生较大的上浮,从而对结构造成比较严重的破坏;地铁结构在地震作用下的最大内力位于结构的交接处。因此,结构交接处的配筋应该格外小心。 相似文献
16.
The stick-slip of frictional sliding depends not only on material properties but also on the elastic and inertial properties of the loading system. To compare data from different testing machines or to apply them to the problem of natural seismogenic faulting, one must account for the differences in stiffness and mass. We develop a simple mechanical model to describe the stick-slip oscillation during frictional sliding in a triaxial-compression machine. The experimental system, the loading frame and rock specimen with precut sliding surface, is divided into two subsystems across this surface. The model is based upon two key assumptions: the kinetic friction is constant regardless of the relative motion of the subsystems, and the elastic restoring force is uniform throughout each subsystem. The first assumption leads to the decoupling of the subsystems, and the behavior of each becomes mathematically analogous to that of a simple spring/mass/slider-block model, owing to the second assumption. The theory agrees well with the experimental data from the dynamic measurements of stick-slip. The displacement-time function is of cosine form, the rise time of stick-slip is constant, and the relation between force drop and average displacement rate is linear. From this model we argue that the differences in the frictional behavior of experimental fault-gouges may indeed be ascribed to differences in the material properties of their specimens because the elastic and inertial properties of a particular testing machine are little influenced by the specimen itself, so long as all specimens are of about the same size. However, interlaboratory correlations may well be invalid unless machine effects are properly accounted for. 相似文献
17.
地震作用下挡土墙主动土压力及转动位移分析 总被引：2，自引：0，他引：2
分析地震引起的挡土墙位移及墙后土压力,对于评估挡土墙可靠性具有重要意义。基于拟动力法,考虑时效、地震波传播的相位差、超载、墙背摩擦角、填土黏聚力以及填土开裂等影响,建立地震作用下挡土墙主动土压力计算模型,获得挡土墙绕墙趾转动模式下主动土压力大小、分布形式及作用点高度。同时,考虑挡土墙本身受地震荷载作用的影响,求出挡土墙绕墙趾的转动位移。通过与Mononobe-Okabe法对比可知,文中获得的主动土压力值与Mononobe-Okabe法接近,但Mononobe-Okabe法低估了主动土压力作用点高度,表明采用Mononobe-Okabe法设计存在风险。通过算例分析了地震系数、墙背摩擦系数、超载大小、时间、填土黏聚力和内摩擦角对挡土墙转动位移的影响。 相似文献
18.
强风化软硬互层岩质高边坡属岩质边坡特殊情况,其结构面组成及性质复杂,与支护结构相互作用的复杂程度较高,相互影响较大,顺倾结构面临空等情况下破坏可能性很大。以兰永一级公路某深挖路堑边坡的治理工程为依托,对边坡支护过程中及支护结束后的锚杆应力、锚索内力、坡体位移进行了原位监测,并利用岩土分析软件PLAXIS,采用节理岩模块对该边坡工程进行了数值模拟分析。监测及模拟结果表明：该边坡由节理裂隙与岩层面形成折线形潜在滑面,且具有相同滑动可能性的潜在滑面不止一个;支护结构穿透组成滑面折线的任何折线段部分均对结构面稳定有显著影响,但支护结构穿透泥岩面对结构面的影响较穿透节理裂隙更大;支护锚索预应力变化具有一定规律,预应力变化过程对坡体位移及支护结构内力具有一定影响;坡体的主动变形对支护结构内力的影响较坡体被动变形大,结构面产生滑动趋势对坡面位移影响的敏感程度较支护结构内力影响的敏感程度低。该边坡支护稳定,支护设计合理,可为同类边坡支护设计提供相应建议。 相似文献
19.
基于Morgenstern Price法和强度折减法的边坡稳定性对比分析 总被引：3，自引：0，他引：3
应用Morgenstern-Price法和强度折减法,对云南省宣威市万家口子水电站附近的九子崩塌堆积体的主滑体进行稳定性分析,考虑了正常蓄水位、库水位下降和地震作用时的正常蓄水位、库水位下降4种工程情况。结果表明：Morgenstern Price法所得稳定系数随着蓄水位的下降而减小,在考虑地震作用的情况下,稳定系数也相应降低;强度折减法所得数据则不一样,蓄水位不同时,稳定系数则变化不大。相同蓄水位情况下,考虑地震时稳定系数有所减小,强度折减理论对于简单的均质土坡可能会得到与极限平衡法接近的稳定系数和滑动面,但对于非均质（如成层）土坡,则会有较大的差异性。Morgenstern-Price法使用条分法对滑动岩土体进行受力分析,针对的是人为假定的土体极限平衡条件,不能提供边坡的位移信息,需在计算中事先假定出若干个滑动面;强度折减法通过降低材料的强度参数来达到极限平衡状态,能够考虑土体的应力-应变关系,同时能给出边坡的位移信息,但是缺乏统一的边坡达到极限破坏的判断标准。2种方法都可为边坡稳定性提供有效的分析与评价。 相似文献
20.
Disk clusters are developed to represent the shape of granular materials more precisely (compared to circular particles) and to minimise excessive rolling. Investigating the behaviour of dynamic disk-based discontinuous deformation analysis (DDA) with disk clusters is very important to evaluate the applicability of disk-based DDA to dynamic problems in geomechanics. In this paper, the accuracy of disk-based DDA under dynamic conditions is studied by a comprehensive sensitivity analysis. The results obtained by disk-based DDA are compared with the analytical solutions of a disk cluster on an incline subjected to gravitational force only, and three different accelerations of increasing complexity with sinusoidal input functions as well as gravitational load. In this research, the effects of time step size and interface friction angles on the results are studied. Overall, most of the error for both velocity and displacement occurs at the beginning of the solution. With increasing friction angle, the initial perturbation of the solution increases in the case of sliding under gravitational force only, and decreases in the case of sliding under dynamic loads. This study shows that disk-based DDA predicts accurately the velocities and displacements derived with respect to the frictional resistance offered by the inclines. 相似文献