共查询到20条相似文献，搜索用时 703 毫秒
1.
磷作为海洋浮游生物生长必需营养元素之一,其准确测定对海洋生态系统元素循环过程的研究具有重要意义。目前,文献中对于海洋浮游生物中总磷的测定方法报道不多。由于海洋浮游生物生存的高盐海洋环境,高盐基体的存在导致常规检测方法不能准确测定磷的含量。为剔除高盐基体效应及干扰,本文运用微波密闭消解预处理样品,采用电感耦合等离子体发射光谱法(ICP-OES)联合标准加入法建立工作曲线,同时结合样品的特异性,对ICP-OES分析谱线、射频功率、雾化气流速、观测高度、蠕动泵泵速和观测方式等仪器参数进行优化,构建确定了准确测定海洋浮游生物中总磷的优化条件和技术流程。实验结果显示, ICP-OES最佳工作条件为分析谱线P213.617 nm,射频功率1 300 W,雾化气流量0.8 L/min,观测高度14mm,进样泵速1.5 m L/min,观测方式轴向。标准加入法标准曲线相关系数大于0.999,相对标准偏差为1.36%~1.67%,加标回收率为92.6%~94.3%,方法检出限为0.010 mg/L,检测结果具有较高的准确度和精密度,可为海洋浮游生物及其它高基体生物样品中磷含量的准确测定提供技术支持。 相似文献
2.
海水中硼的快速测定方法 总被引：2，自引：2，他引：2
海水、卤水及废水等样品中微量硼的测定方法很多,其中姜黄素法是测硼灵敏度最高的一种,现已被列入美国《水和废水标准检验法》第13版中。我们以姜黄素-分光光度法测定海水中微量硼时,在标准曲线中加入了与海水样相当的无硼人工海水,消除了阴阳离子的干扰,在半年多的海水中硼的间断性测定试验方面,获得了较满意的结果,其相对标准偏差为3.1％,测一批样品仅需4小时,因此,该法是测定海水中硼的快速准确的较好方法。 相似文献
3.
运用电感耦合等离子体发射光谱法(Inductively Coupled Plasma-Optical Emission Spectrometry,ICP-OES)比较研究了干法灰化、湿法消解和微波消解3种前处理方法对海带样品中Se、Fe、Mn、Zn、Ca、Mg、P、As、Cd、Cr、Cu和Pb 12种元素含量测定的影响。结果表明,不同前处理方法对微量元素的测定结果会产生不同程度的影响。干法灰化对易挥发元素As等带来明显的负误差;湿法消解由于加入的消解液量大,对低含量的微量元素常带来较大的试剂空白;微波消解法相对于其他两种前处理方法适于样品的快速消解,具有操作简便、试剂用量少、操作误差小等优点,检测结果具备较高的准确度、精密度和回收率,对海带样品微波消解ICP-OES检测的相对标准偏差为0.29%~2.63%,加标回收率为87.3%~103.6%。微波消解是海带等海洋生物样品中微量元素测定较理想的前处理方法。 相似文献
4.
ICP-AES测定海洋生物体中13种元素的微波消解条件优化 总被引：3，自引：1，他引：2
报道了微波密闭消解正交试验条件优化电感耦合等离子体发射光谱法(ICP-AES),同时测定8种海洋生物体中硒、铁、锰、锌、钙、镁、锶、砷、镉、铬、铜、铅和镍等13种元素含量的实验结果。优化后的样品消解条件为加入的HNO3V:H O2 2V=6.0 mL:1.0 mL,第二步程序升温温度为170℃,消解时间20 min;测定标准曲线相关系数大于0.999,相对标准偏差为0.30%~2.55%,加标回收率为92.0%~104.8%,方法检出限为0.0010~0.0468μg/g。结果表明,优化后方法测定操作简便、具有高的灵敏度、准确度和精密度,且能多元素同时测定,适合于海洋生物样品中这些元素含量的准确测定,并可为评估海产品食用安全提供科学依据。 相似文献
5.
元素分析仪快速测定海洋沉积物TOC和TN的条件优化 总被引：4，自引：0，他引：4
报道了在优化样品前处理、燃烧温度、最小加氧量和最佳称样量的基础上,综合构建优化了直接固体进样varioMACRO cube元素分析仪同时测定海洋沉积物样品中总有机碳(TOC)和总氮(TN)的条件,即准确称取20~30 mg沉积物样品用1 mol/L盐酸除去无机碳后,直接进样在燃烧管温度960℃,次级燃烧管温度830℃,还原管温度900℃,氦气压力0.12 MPa,流量600 mL/min,氧气压力0.20 MPa,加氧量22.5 mL仪器条件下,用标准曲线法峰面积获取TOC和TN浓度。结果表明,海洋沉积物中TOC和TN测定的检出限分别为0.0508%和0.0146%,回收率分别为97.7%~100.9%和97.2%~101.1%,对4个实际外海沉积物样测定总有机碳和总氮结果的相对标准偏差(RSD)为0.83%~3.06%和1.33%~3.49%(n=12)。该方法操作简便快速、灵敏度高,具有较好的精密度和准确度,可准确可靠地用于海洋沉积物中总有机碳和总氮含量的测定。 相似文献
6.
离线固相萃取螯合富集分离-ICP-MS测定海水中的稀土元素 总被引：1，自引：0，他引：1
通过测定条件优化、方法比对等实验建立了一种固相萃取小柱离线螯合富集分离电感耦合等离子体质谱仪测定海水中稀土元素的方法。海水样品通过调节p H后,进入VAC ELUT SPS24 Agilent圆形固相萃取装置,其主要基体物质的去除率高于97%;萃取富集的优化条件是海水样品p H 4.0~7.0,海水进入萃取柱速率2 m L/min,硝酸洗脱液浓度为1 mol/L;方法对稀土元素的加标回收率为83%~108%,14种稀土元素的检出限为0.057~0.613 ng/L,RSD10%;该方法与氢氧化铁共沉淀法富集稀土元素比对测定结果一致,方法具有准确度与精密度高、操作简便快速等优点,可用于海水样品中稀土元素的定量精确测量。 相似文献
7.
8.
本文研究并建立了海水中测定砷形态的液相色谱—原子荧光法。进行了实验参数流动相浓度、pH、流速的优化。在优化的实验条件下，采用Hamilton PRP-X100分析柱在6 min内可以完成三价砷、甲基砷和五价砷3种形态的分离、检测。在载流5% HCl，还原剂2% KBH4、0.5% KOH，进样量100 μL的条件下，三价砷、甲基砷和五价砷的检出限分别为0.31 μg/L、0.52 μg/L和0.36 μg/L。在浓度2~80 μg/L范围内，3种砷形态均有良好的线性关系，相关系数均优于0.999。用本文所建立的方法进行了海水样品中无机砷和有机砷形态的测试，海水中三价砷、甲基砷的含量较低，五价砷稍高，说明海水中砷形态主要以五价砷存在，当加标量为5~10 μg/L，加标回收率在73%~104%之间。该方法操作前处理简单，灵敏度高、运行费用低廉，适用于海水中砷形态的测试。 相似文献
9.
本文选择酒石酸消除海水基体对铜信号的干扰,用塞曼石墨炉原子吸收法直接测定海水中的铜。从Cu的原子化曲线可知,加入酒石酸后,背景值减小,Cu原子吸收信号增强,且出现时间提前,表明酒石酸是有效的海水基体改进剂。用P.E.Z3030光谱仪测得双蒸水及海水中的元素Cu的特征质量(m。)分别为12.5pg及12.7pg;检测限分别为0.18μg/L和0.19μg/L,表明基体效应已消除,符合海洋监测要求。可用纯Cu标准溶液作校正曲线,以国家海洋局的两个标准海水样品中的Cu评定本法的准确度,相对偏差为0及-4.6%,与经典的经富集后的FAAS法的结果相比,相对偏差在3.0—6.5％范围内。用不同类型的光谱仪测定了30个海水样品,回收率在89—104％范围内。本法操作简便、快速。 相似文献
10.
如何去除元素硫高含量样品的背景硫,是测定该类样品中微量元素成功的关键.通过分别对样品进行燃烧和升华两种前处理方法的研究对比,得出用升华的方法处理自然硫样品对于其微量元素的测定可靠性大,所测定微量元素回收率的优良率是68%,燃烧法处理后测定微量元素回收率的优良率是64%.而且前者优良回收率的范围是79.9%~120.5%,明显高于后者的优良回收率范围76.2%~98.0%.对于这样的结果,温度是主要的控制因素.燃烧法处理样品温度条件较难控制,升华法则可以较严格的控制温度,从而减少被测元素的散失,能得到较为理想的数据. 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
13.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
14.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
15.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
16.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
Shigehisa Nakamura 《Marine Geodesy》2000,23(1):55-61
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone. 相似文献
19.
20.